solarMate-10
10000mAh
Heavy Duty SOLAR Powered Battery Pack
• solarMate-10
• Micro-USB Charging Cable
• User Guide
Introduction
Packaging Contents
Thank you for purchasing solarMate-10. Get power-on-the go when outdoors
with solarMate-10. This revolutionary new solar powered battery pack is built
keeping durability and functionality in mind. Charge two devices simultane-
ously even when you are not around any electrical output. With solarMate-10’s
Monocrystalline Silicon Solar Panel, charge your device under incandescent
light indoors. Never run out of battery on long ights, extended meetings or
those outdoor events. Charge two devices at a lightning speed with two fast
USB charging interface’s and get to know the power level with the LED
indicator. Utilize the best renewable energy source known to mankind at its
optimum level with solarMate-10.
English
1
Specication
• Battery Type: Li-polymer.
• Capacity: 10000mAh
• Input: Micro USB 5V/1.5A(Max),
• Solar Charging: 5V/200mA(Max),
• Output:USB1: 5V/1.3A(Max),
USB2: 5V/2.1A(Max)
• Charging Time: via Solar Power: 55-60 hrs
via USB: 7-8 hrs.
Features
• Powerful 10000mAh Capacity Li-polymer Battery.
• Charge two devices simultaneously.
• Monocrystalline Silicon Solar Panel
• Fast USB Charging Interface.
• Power on-the-go.
• Key Chain Design.
• Heat Dissipating ABS Plastic Shell
• LED battery level indicator.
• Intelligent Power Management with 7 Protection: Overvoltage protection,
Overcurrent protection, overcharge protection, short-circuit protection,
over power protection, over discharge protection. Temperature protection
• Compatible with all Smartphones and Tablets.
• LED Light.
English
2
Precautions
Please read all safety instructions and warnings thoroughly before using this
product. Improper use of this product may result in damage to this or
attached products.
1. Do not disassemble the back-up battery or attempt to x it.
2. Kindly use an original charging cable provided to charge the product.
3. Do not attempt to replace any part of this Back-up battery or battery
inside.
4. Do not crush, puncture, dispose of in re, short the contacts or expose the
battery to water or other liquids.
5. Do not connect input and output in reverse.
6. Do not store or use the battery in a high temperature environment,
including intense sunlight or heat.
7. Avoid drops, bumps, abrasions and impacts.
8. If there is any reason to believe that there is damage to the battery,
discontinue use immediately.
9.If you nd that the battery is too hot, is emitting an odor, or is deformed,
punctured or exhibits any suspicious or abnormal behavior, discontinue use
immediately and contact our customer service.
10. Always charge this product before extended storage.
English
3
Tap the Multi-Function button once to view the amount of power remaining in
solarMate-5
1. Checking the remaining power left in solarMate-10 back-up battery
Appearance & Interface Description:
1. Solar Panel
2. LED Indicators
3. Multi-function button.
4. USB Output
5. LED Light
6. USB Output
7. Micro USB Input
Operation Instructions:
English
4
Plug the Micro-USB end of the charging cable provided into the Micro-USB
charging port in solarMate-10 back-up battery. Connect the other end of the
Micro-USB charging cable to a USB power adapter or computer USB port. The LED
battery level indicator light’s up indicating that the back-up battery is charging
normally.
solarMate-10, can be recharged by solar energy when kept under the sun rays or in
the environment with strong sunlight. solarMate-10 may also be charged using
incandescent light.
of power remaining %
No of LED’s Active
<=25% <=50% <=75% <=100%
1 2 3 4
2. Charging solarMate-10 back-up battery
English
5
3. Charging USB chargeable devices using solarMate-10
• Press and hold the Multi-function button for 3 seconds to turn ‘on’ the LED Light.
• Again press the Multi-function button for 3 seconds to turn ‘o’ the LED Light.
4. Using the LED Light on solarMate-10
There are 2 ports available on solarMate-10. It is recommended to use the 1.3A
charging output port to charge smartphones and the 2.1A charging output port to
charge tablet devices. Plug the USB cable into the USB output port on solarMate-10
back-up battery and the other end into the device. Press the multi-function button
once to start charging your device. Detach the USB cable once charging is
complete.
English
6
Loading...