Blk 16 Kallang Place #06-02
Singapore 339156
1. CAUTION English
The UPS battery has been fully charged before leaving our factory. During the shipment,
some level of power may have been discharged. In order to ensure the efficiency of the UPS,
please allow the UPS to charge its battery for at least 12 hours before use.
Connect the UPS to a two-pole, three-wire grounding mains (AC). T he AC source must be
connected to appropriate branch protection (fuse or circuit breaker). Connection to any other
type of AC source may result in a shock hazard and may violate your warranty claim.
This UPS has an internal battery and its energy can not be de-energiz ed by the user. The
output may be energized even though when the UPS is not connected to the main AC.
DO NOT install the UPS in locations where there is water or excessive humidity.
DO NOT allow water or any foreign object to enter the UPS or put any objects containing
liquid on or near the UPS.
DO NOT remove the cover. No user serviceable parts. Refer servicing to qualified service
personnel.
DO NOT connect any non-computer peripherals to the UPS. The UPS is designed for use
with computer loads only.
To reduce the risk of overheating the UPS, avoid exposing the un it to direct sunlight. Avoid
installing the unit near heat emitting appliances such as a room heater or stove.
Certificate Number: SGPSGP001496
2. OPERATION
2.1 Operating Instructions
A. Connect the AC input power cable of your UPS to the AC Power. ‘YELLOW’ LED on
the UPS front panel is lit. UPS is charging the battery. (Note: DO NOT connect any
load to your UPS until the UPS has charged its battery for 12 hours)
B. Plug computer and monitor t o UPS sockets. (Note: Power of computer and monitor
must be less than the maximum total power of your UPS. DO NO T con n ec t a l aser
printer to the UPS backup socket. Laser printers draw a significantly more pow er
than other types of equipment and may overload the UPS.)
C. Switch on the UPS by pressing the power switch on the front panel. The ‘GREEN’ LED
on the UPS front panel is lit and ‘YELLOW’ LED is off. UPS is supplying utility power to
the connected equipment and is still charging battery at the same time.
D. When external power source fails, the UPS will power up automatically by batteries.
The ‘YELLOW’ LED is blinking and the UPS has beep sound every 10 seconds. You
should save all your data and close all applications as soon as possible and turn off the
UPS.
E. When the battery output voltage dro ps to a minimum, the ‘YELLOW’ LED on the UPS
front panel is blinking while generating beeps every 1 second. You sho uld turn off the
main switch of the UPS.
2.2 UPS Status Information
UPS Status Buzzer
Yellow Green Red
Offline mode, Charge
Battery
AC mode, UPS Normal No beeps OFF ON OFF
AC abnormal
UPS in battery mode
Battery voltage low Every sec Blinking OFF OFF
Overload in AC mode Every 0.5 sec OFF ON OFF
Overload in Battery mode Every 0.5 sec Blinking OFF ON
UPS fault / Short circuit Continuous Sounding OFF OFF ON
Discharge Finished No beep OFF OFF OFF
No beeps ON OFF OFF
Once every 10 sec Blinking OFF OFF
LED Indication
2.3 Front / Rear Panel Explanation
Yellow LED
ON when UPS is offline charging battery.
Blinking when AC is abnormal.
Green LED
ON when UPS is running normal.
OFF when UPS is off or abnormal.
Red LED : On only when UPS is fault
2.4 Troubleshooting
Problem Possible Cause Solution
MAIN Switch : Control UPS On/Off
A. AC Inlet
B. Backup Outlets
C. AC Fuse Holder (W/fuse)
Green LED does not light up
when UPS is turn on. Yellow
LED is blinking and UPS is
beeping.
UPS beeps occasionally on AC
mode and UPS may be heated
up.
Battery backup time is short.
Beeping sound is heard every
second
1. AC power not on.
2. Power cable not properly
inserted.
3. Fuse blown.
4. Faulty wall socket.
1. UPS may be overloaded.
2. Unstable AC supply.
1. UPS may be overloaded.
2. Battery not fully charged.
3. Battery may be near the
end of its lifespan.
1) Turn on AC power.
2) Insert power cable
properly.
3) Change the fuse.
4) Change to another wall
socket.
1) Check that your
equipment matches the
specified capacity of your
UPS. Do not overload
your UPS.
2) Refer to qualified electrical
technician to check your
AC supply and wiring.
1) Remove any non critical
equipment.
2) Charge the battery for at
least 8 hours before use.
3) Refer to supplier for
replacement of battery
(charges may be
involved).
3. SPECIFICATIONS
Model PRO700
Capacity 650VA
Voltage Range 140 – 300VAC ± 5VAC Input
Frequency > 40 Hz
Phase Single + GND
Voltage Range 230VAC + 11% - 17% Output
Battery Mode 230VAC ± 10%
Frequency 50Hz ± 1Hz (Battery Mode)
Waveform
Transfer Time 2ms typical
Type & Number 12V8.2AH – 1pc Battery
Backup Time 8 – 20 minutes depending on load
Recharge Time 90% Capacity after 8 hours
Protection/
Monitoring
Interface
Short Circuit
Protection
Surge Protection Yes
Alarms Audible & Visual
Over Temperature
Protection
Overload
Protection
Intelligent Battery
management
Interface NA
9P D-Type
Connector
Software (optional) NA
Noise <40dB General
Temperature 0ºC - 40ºC
Humidity 0% - 95% relative humidity
Power Factor Up to 0.7
Built-in AVR Full AVR (3 Steps)
*Specifications are subject to change without prior notice.
Simulated Sine Wave (Battery Mode)
Sine Wave (AC Mode)
Line mode – Fuse & software protection (CPU)
Battery mode – Software protection (CPU)
>75ºC Alarm will sound
>85ºC the system will shutdown
Line Mode: 100-120% 5 minutes change to fault mode
>120% change to fault mode immediately
Battery Mode: 100 – 120% 5 secs shut down;
>120% shut down immediately
Prevent overcharging of battery.
Protect battery and prolong battery life.
NA
1. PERHATIAN Bahasa Indonesia
Baterei UPS sudah diisi penuh sebelum keluar dari pabrik. Selama pengiriman, kapasitas
dari isi baterei akan berkurang. Untuk memastikan efisiensi dari UPS, sebaiknya baterei
diisi kembali sebelum digunakan selama 12 jam.
Hubungkan UPS ke pusat listrik dengan menggunakan kabel 3 pin (berikut grounding).
Grounding ini sangat berguna untuk memproteksi peralatan kita dari petir.
UPS ini mempunyai baterei internal dan energi nya tidak bisa dibuang. Output dari UPS
sendiri akan mengeluarkan arus listrik walaupun UPS tidak dihubungkan langsung ke aliran
JANGAN meletakan UPS di dekat daerah yang lembab atau basah.
JANGAN biarkan air atau benda asing lain nya masuk kedalam UPS.
JANGAN membuka casing UPS atau melakukan reparasi sendiri.
JANGAN gunakan UPS ini ke peralatan yang bukan peralatan komputer. UPS ini hanya di
rancang untuk digunakan oleh peralatan komputer saja.
Untuk mengurangi resiko panas yang berlebihan dari UPS, jangan meletakan UPS yang
langsung terkena sinar matahari atau hindari peletakaan ya ng dekat dengan peral atan yang
mengeluarkan panas.
Certificate Number: SGPSGP001496
2. PENGGUNAAN
2.1 Instruksi Penggunaan
A. Sambungkan kabel power dari UPS ke sumber listrik (PLN). Lampu ‘KUNING’ akan
menyala. Artinya UPS sedang melakukan charging ke baterai. (Note: JANGAN dulu
menggunakan UPS anda sampai baterai dari UPS anda sudah di charge selama
kurang lebih 12 jam).
B. Sambungkan komputer dan monitor anda ke output UPS. (Note: Total daya dari
komputer dan monitor harus lebih kecil dari kemampuan output daya maximum
dari UPS anda. JANGAN gunakan peralatan yang melebihi dari kemampuan UPS
anda. seperti laser printer, karena Laser printers membutuhkan daya yang sangat
besar dari peralatan komputer anda yang lainnya)
C. Nyalakan UPS dengan menekan tombol power yang ada pada panel depan. Lampu
‘HIJAU’ akan menyala dan lampu ‘KUNING’ akan padam. Artinya UPS bekerja dengan
menggunakan listrik PLN dan tetap melakukan charging ke baterai dalam waktu yan g
bersamaan.
D. Ketika sumber listrik padam, UPS akan bekerja secara otom atis dengan menggunakan
baterai. Lampu ‘KUNING’ akan berkedip dan diikuti dengan suara beep di setiap 10
detik. Saat ini anda harus menyimpan seluruh data anda dan matikan UPS secara
manual.
E. Ketika output dari baterai melemah, lampu ‘KUNING’ akan terus berkedip dan diikuti
dengan suara beep disetiap detik. Anda secepatnya harus mematikan UPS secara
manual. Ini sering terjadi untuk UPS jenis tanpa software monitoring.
2.2 Informasi Status UPS
Status UPS Buzzer
KUNING HIJAU MERAH
Mode AC, Baterai Charge Tidak ada Bunyi HIDUP MATI MATI
Mode AC, UPS Normal Tidak ada Bunyi MATI HIDUP MATI
Sumber Listrik Padam,
dan UPS bekerja dengan
baterai
Output Baterai melemah
Overload pada kondisi AC
Overload pada kondisi
Battery
UPS bermasalah Bunyi beep panjang MATI MATI HIDUP
Proses Discharge Selesai Tidak ada Bunyi MATI MATI MATI
Bunyi beep setiap 10
detik
Bunyi beep setiap
detik
Bunyi beep setiap 0.5
detik
Bunyi beep setiap 0.5
detik
2
Berkedip MATI MATI
Berkedip MATI MATI
MATI HIDUP MATI
Berkedip MATI HIDUP
Indikator Lampu
2.3 Penjelasan Panel Depan
Lampu KUNING
HIDUP ketika UPS sedang melakukan
Proses charging
BERKEDIP ketika sumber listrik (PLN)
padam
Lampu HIJAU
HIDUP ketika UPS bekerja normal.
MATI ketika UPS mati atau tidak normal.
Lampu MERAH
HIDUP UPS overload, atau bermasalah
MAIN Switch
2.4 Permasalahan Dan Solusi
Masalah Possible Cause Solution
Untuk mengontrol UPS HIDUP / MATI
A. AC Inlet
B. Backup Outlets
C. AC Fuse Holder (W/fuse)
Lampu HIJAU tidak menyala
pada saat UPS dihidupkan.
Lampu KUNING berkedip
dan mengeluarkan bunyi
Beeps.
Terdengar bunyi beep pada
kondisi UPS terhubung listrik
(PLN) atau UPS mengalami
panas yang berlebihan.
Waktu backup baterai yang
pendek.
Mengeluarkan bunyi beep.
1. AC power tidak menyala
2. Kabel input listrik tidak
terpasang dengan benar.
3. Sekering terputus.
4. Kerusakan di soket
koneksi listrik pada
dinding.
1. Beban UPS yang
mungkin berlebih.
2. Listrik yang kurang stabil.
1. Beban UPS yang
mungkin berlebihan
2. Battery tidak di isi dengan
penuh.
3. Battery mungkin sudah
dekat dengan masa
pakainya
3
1) Nyalakan AC power.
2) Pastikan pemasangan
kabel power listrik sudah
terpasang dengan benar.
3) Ganti sekering yang putus.
4) Ganti ke soket listrik yang
lainnya.
1) Periksa semua peralatan
yang terhubungkan ke UPS.
Pastikan beban tidak
melebihi kapasitas dari
UPS.
2) Mengacu pada teknisi yang
ahli dalam bidang kelistrikan
untuk memeriksa soket dan
kabel listrik
1) Lepaskan barang-barang
yang tidak terlalu di
perlukan dari UPS.
2) Lakukan pengisian battery
sedikitnya lebih dari 8 jam
sebelum di gunakan
3) Bawa UPS pada supplier
untuk mengganti battery
(dengan pergantian battery
mungkin dapat membantu)
3. SPECIFICATIONS
Model PRO700
Capacity 650VA
Voltage Range 140 – 300VAC ± 5VAC Input
Frequency > 40 Hz
Phase Single + GND
Voltage Range 230VAC + 11% - 17% Output
Battery Mode 230VAC ± 10%
Frequency 50Hz ± 1Hz (Battery Mode)
Waveform
Transfer Time 2ms typical
Type & Number 12V8.2AH – 1pc Battery
Backup Time 8 – 20 minutes depending on load
Recharge Time 90% Capacity after 8 hours
Protection/
Monitoring
Interface
Short Circuit
Protection
Surge Protection Yes
Alarms Audible & Visual
Over Temperature
Protection
Overload
Protection
Intelligent Battery
management
Interface NA
9P D-Type
Connector
Software (optional) NA
Noise <40dB General
Temperature 0ºC - 40ºC
Humidity 0% - 95% relative humidity
Power Factor Up to 0.7
Built-in AVR Full AVR (3 Steps)
*Specifications are subject to change without prior notice.
Simulated Sine Wave (Battery Mode)
Sine Wave (AC Mode)
Line mode – Fuse & software protection (CPU)
Battery mode – Software protection (CPU)
>75ºC Alarm will sound
>85ºC the system will shutdown
Line Mode: 100-120% 5 minutes change to fault mode
>120% change to fault mode immediately
Battery Mode: 100 – 120% 5 secs shut down;
>120% shut down immediately
Prevent overcharging of battery.
Protect battery and prolong battery life.
NA
4
TECHNICAL SUPPORT
FREE TECHNICAL SUPPORT HOTLINE:
Mon to Fri: 9am - 6pm
(Closed on Saturdays, Sundays & Public Holidays)
Singapore : (65) 6357 0666
Malaysia : (60) 3 802 3 9151
Indonesia : (62) 21 628 3205
OPERATING HOUR:
Mon to Fri: 9am - 6pm
(Closed on Saturdays, Sundays & Public Holidays)
Singapore
FIDA INTERNATIONAL (S) PTE LTD
Blk 16 Kallang Place #06-02
Kallang Basin Industrial Estate Singapore 339156
Malaysia
FIDA SYSTEMS (M) SDN BHD
29 USJ 1/31, 47600 Subang Jaya Selangor,
Darul Ehsan, Malaysia
Indonesia
PROLiNK INDONESIA
P.Jayakarta Komplek 85 BR/AJ, Jakarta Pusat, Indonesia
ONLINE TECHNICAL SUPPORT:
support@fida.com
Register Online For Your Product Warranty
www.prolink2u.com
SINGAPORE
FIDA INTERNATIONAL (S) PTE LTD
Block 16 Kallang Place, #06-02 Kallang Basin Industrial Estate, Singapore 339156.
Tel : (65) 6357 0668 Email : support@fida.com
MALAYSIA
FIDA SYSTEMS (M) SDN BHD
29 Jalan USJ 1/31, 47600 Subang Jaya, Selangor Darul Ehsan, Malaysia.
Tel : (60) 3 8024 9151 Email : support_my@fida.com
INDONESIA
PROLiNK INDONESIA
P. Jayakarta Komplek 85 BR/AJ, Jakarta Pusat - Indonesia.
Tel : (62) 21 628 3205 Email : support@prolink.co.id
© 2009 Fida International (S) Pte Ltd. Version 1.0 (Jul’09).
PROLiNK is a trademark of Fida International (S) Pte Ltd and is manufact ured under its authority. All
other brands, products, services, logos and company names mentioned herein are trademarks of their
respective owners. All specifications, desig ns and contents are subject to changes with out prior notice.
© Copyright 2009. PROLiNK all rights reserved.
Loading...