Prokit's Industries MT-7810 User Manual

MT-7810 SATELLITE FINDER KIT

USER GUIDE

INTRODUCTION

THANK YOU VERY MUCH FOR BUYING OUR SATELLITE FINDER KIT WHICH WILL HELP YOU TO RECEIVE

SATELLITE PROGRAMS AS YOU WISH WITH YOUR TV WITHOUT ANY PROBLEM.

PLEASE USE THIS ACCORDING TO THE FOLLOWING PROCESS TO SET UP YOUR SATELLITE ANTENNA.

1. BEFORE BEGINNING TO SET UP A SATELLITE ANTENNA, YOU SHOULD CHOOSE A SUITABLE PLACE FOR IT.

SUCH AS, ON THE WALL, ROOF, OR IN THE GARDEN, ETC. KEEP IN MIND THAT THE DISH SHOULD HAVE A

WIDE-OPEN OF VIEW OF THE SKY IN THE DIRECTION OF THE SATELLITE (ASK YOUR PROVIDER).

2. PLEASE REFER TO THE TABLE BELOW TO DETERMINE THE DIRECTION AND AZIMUTH OF THE SATELLITE

YOU WISH TO RECEIVE.

3. PLEASE USE ACCORDING TO THIS INSTRUCTION MANUAL FOR ALL THE REQUIRED ADJUSTMENTS.

160˚W-73˚E 73˚E-0˚E 0˚W-61˚W 61˚W-160˚W

Satellites: Asia Europe Atlantic America
Packages: Asia Europe Atlantic America
HD TV: Asia Europe Atlantic America
SatTracker: Asia Europe Atlantic America

For more details, go to http://www.lyngsat.com/

OPERATION MANUAL

1. FIX LNB TO DISH FIRST.

2. CONNECT A RF JUMPER CABLE FROM LNB TO LEFT SIDE OF SATELLITE FINDER (“TO LNB” TERMINAL).

3. CONNECT BATTERY PACK TO RIGHT SIDE OF THE SATELLITE FINDER (“TO REC/DC 15V” TERMINAL).

4. THE NEEDLE OF THE METER SHOULD INDICATE MOVEMENT WITHIN THE FULL SCALE OF THE METER

(BETWEEN 0 AND 10, AND THE SCALE WILL LIGHT UP.

5. REFER TO TABLE ABOVE AND MAKE COARSE DISH ALIGNMENT BY SETTING AZIMUTH AND INCLINATION.

6. SET THE NEEDLE OF THE METER ON THE MIDDLE SCALE BY ADJUSTING SATELLITE FINDER’S

“SENSITIVITY CONTROL” ADJUST THE ANGLE AND DIRECTION OF THE DISH, IF YOU CATCH THE SIGNAL,

THE NEEDLE WILL JUMP TO NEAR FULL SCALE.

7. ADJUSTING THE “SENSITIVITY CONTROL” KNOB COUNTERCLOCKWISE, SET NEEDLE ON THE MIDDLE OF

THE SCALE. REPEATEDLY ADJUST THE DISH AND “SENSITIVITY CONTROL” KNOB UNTIL YOU GET THE

BEST RECEPTION.

8. FIX THE ANGLE AND DIRECTION OF THE DISH, REMOVE THE RF JUMPER CABLE AND SATELLITE FINDER.

RESUME CONNECTION OF SATELLITE RECEIVER TO LNB.

REMARK:

1. WHEN USING THIS UNIT WITH A “C” BAND DISH, YOU MUST NOT PLACE THE SATELLITE FINDER IN FRONT

OF DISH. DOING SO WILL RESULT IS A CONSTANT FULL-SCALE READING.

2. IF THE READ-OUT IS JUMPING OR ALWAYS FULL-SCALE, THE INPUT SENSITIVITY IS TOO HIGH. LOWER

THE SENSITIVITY BY ADJUSTING “SENS. ADJ.” ON THE SATELLITE FINDER BOTTOM. ON THE OTHER HAND,

ADJUST THE “SENS. ADJ.” CLOCKWISE TO INCREASE SENSITIVITY.

A. SATELLITE FINDER SPECIFICATION

ITEM: SPECIFICATION:

Frequency Range: 950-2400MHz
Gain: 18dB
Sensitivity: 7dB
Power Supply: DC 13-18V
Operation Ranger(Input/Output): 52-60dB
Connector: “F” Type Female
Impedance: 75 Ohm
Dimension(mm): 100 x 60 x 30

B. LENSATIC COMPASS

ITEM: SPECIFICATION:

Direction Accuracy: +/- 5
Direction Indication: 0 - 10 scale
Dimension (mm): 75 x 55 x 30

C. RF JUMPER CABLE

ITEM: SPECIFICATION

Connector: “F” Type Male X 2
Cable: RG-59/U
Length: 6ft
Frequency: 5-2150MHz
Insertion Loss: <1dB

D. BATTERY PACK

ITEM: SPECIFICATION
Battery Size: AA Type
Battery Qty: 10pcs/pack
Voltage Output: DC 15V
Connector: “F” Quick Type Male
Wire Length: 6’’
Dimension (mm): 75 x 60 x 30

E. P.V.C CASE

ITEM: SPECIFICATION
Dimension (mm): 245 x 120 x 50

©2012 Prokit’s Industries Co., LTD. All rights reserved 2012001(T)