Page 1
www.proform.com
Model No. PFTL49609.0
Serial No.
Write the serial number in the space
above for reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT CON-
TACT THE STORE; please contact
Customer Care.
USER'S MANUAL
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.proformservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Page 2
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
A
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the locations of the
warning decals. If a decal is missing or il-
legible, call the telephone number on the
front cover of this manual and request a
free replacement decal. Apply the decal
in the location shown. Note: The decals
may not be shown at actual size.
PROFORM is a registered trademark of ICON IP, Inc.
iPod is a trademark of Apple Computer, Inc., registered
in the U.S. and other countries. iPod
®
is not included.
2
Page 3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and in-
tructions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
s
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or persons with
pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 13. To purchase a surge suppressor, see
your local PROFORM dealer or call the telephone number on the front cover of this manual and order part number 146148, or see your
local electronics store.
13. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 22 if the treadmill is
not working properly.)
8. The treadmill should be used only by persons
weighing 300 lbs. (136 kg) or less.
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
11. When connecting the power cord (see page
13), plug the power cord into a surge suppressor (not included) and plug the surge
suppressor into a grounded circuit capable of
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 15).
17. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
3
Page 4
0. Never leave the treadmill unattended while it
2
is running. Always remove the key, unplug
the power cord, and switch the reset/off circuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 20.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
22. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
23. Never insert any object into any opening on
the treadmill.
SAVE THESE INSTRUCTIONS
4. Inspect and properly tighten all parts of the
2
treadmill regularly.
25.
DANGER: Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
ance and adjustment procedures described in
n
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
27. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
4
Page 5
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM
90 C treadmill. The 490 C treadmill offers an impres-
4
sive selection of features designed to make your workouts at home more enjoyable and effective. And when
youʼre not exercising, the unique treadmill can be
olded up, requiring less than half the floor space of
f
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Accessory Tray
Handrail
Upright
®
ing this manual, please see the front cover of this man-
al. To help us assist you, please note the product
u
model number and serial number before contacting us.
The model number and the location of the serial number decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Console
Pulse Sensor
Key/Clip
Walking Belt
Foot Rail
Idler Roller
Adjustment Bolts
Reset/Off
Circuit Breaker
Power Cord
Platform Cushion
5
Page 6
ASSEMBLY
Base Pad Spacer
(13)–2
#8 x 3/4" Screw
(12)–14
#8 x 1" Tek Screw
(2)–4
3/8" Nut (8)–4
#10 x 3/4" Screw
(5)–2
3/8" x 4" Bolt (6)–4
#8 x 3/4" Endcap
Screw (16)–2
#10 Star
Washer (27)–2
3/8" Star
Washer (9)–8
3/8" x 2" Bolt (4)–4
Bolt Spacer (80)–4
3/8" x 1 1/4" Bolt (7)–4
o hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.
T
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
elt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of
b
the walking belt or the shipping carton. This is normal and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex key and your own Phillips screwdriver ,
adjustable wrench , needlenose pliers , and scissors .
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached
to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly. Extra hardware may be included.
6
Page 7
. Make sure that the power cord is unplugged.
1
ith the help of a second person, carefully tip
W
the treadmill onto its left side. Partially fold the
Frame (51) so that the treadmill is more stable;
do not fully fold the Frame yet.
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
Cut the shipping tie securing the Upright Wire
(79) to the Base (86). Use a tie to pull the
Upright Wire out of the indicated hole.
Attach a Base Pad (88) to the Base (86) in the
location shown with a #8 x 1" Tek Screw (2) and
a Base Pad Spacer (13). Then, attach another
Base Pad (88) with only a #8 x 1" Tek Screw (2).
1
B
ole
H
9
7
A
86
88
2
13
88
51
2
2. Attach a Wheel (87) with a 3/8" x 2" Bolt (4) and
a 3/8" Nut (8). Do not overtighten the Nut; the
Wheel must turn freely.
Press a Base Cap (82) into the Base (86).
2
82
86
4
87
8
7
Page 8
. Identify the Right Upright (81) and the Right
3
Upright Spacer (89), which are marked with
“Right” stickers. Insert the Upright Wire (79)
through the Right Upright Spacer as shown. Set
he Right Upright Spacer on the Base (86).
t
Make sure the Upright Wire is not pinched.
Have a second person hold the Right Upright
81) near the Base (86). See the inset drawing.
(
Tie the long tie in the Right Upright securely
around the end of the Upright Wire (79). Then,
pull the other end of the long tie until the Upright
Wire is routed completely through the Right
Upright.
3
81
79
79
Long
Tie
89
86
81
Long
79
Tie
4. Hold a Bolt Spacer (80) inside the lower end of
the Right Upright (81). Insert a 3/8" x 4" Bolt (6)
with a 3/8" Star Washer (9) into the Right
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (80), 3/8" x 4" Bolt
(6), and 3/8" Star Washer (9).
Set the Right Upright (81) into the Right Upright
Spacer (89). Make sure the Upright Wire (79)
is not pinched.
Partially tighten the 3/8" x 4" Bolts (6); do not
fully tighten the Bolts yet.
4
6
81
89
9
79
80
8
Page 9
5. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (51) so the treadmill is more stable; do
ot fully fold the Frame yet.
n
emove and discard the two indicated bolts (A)
R
and the shipping bracket (B).
5
A
B
Attach a Base Pad (88) to the Base (86) in the
location shown with a #8 x 1" Tek Screw (2) and
a Base Pad Spacer (13). Then, attach another
Base Pad (88) with only a #8 x 1" Tek Screw
(2).
Attach a Wheel (87) with a 3/8" x 2" Bolt (4) and
a 3/8" Nut (8). Do not overtighten the Nut; the
Wheel must turn freely.
6. Press a Base Cap (82) into the Base (86).
Set the Left Upright Spacer (83) on the Base
(86). Hold a Bolt Spacer (80) inside the lower
end of the Left Upright (76). Insert a 3/8" x 4"
Bolt (6) with a 3/8" Star Washer (9) into the Left
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (80), 3/8" x 4" Bolt
(6), and 3/8" Star Washer (9). Set the Left
Upright in the Left Upright Spacer.
88
51
2
86
13
4
88
87
2
8
6
6
76
82
9
83
Partially tighten the 3/8" x 4" Bolts (6); do not
fully tighten the Bolts yet.
With the help of a second person, tip the treadmill so that the Base (86) is flat on the floor.
80
86
9
Page 10
7. Press a Front Handrail Cap (106) into the Left
Handrail (110). Attach the Front Handrail Cap
with a #8 x 3/4" Endcap Screw (16).
7
Slide the Left Collar (75) onto the Left Upright
76). Align the large holes in the Left Collar
(
with the large holes in the Left Upright. Set
the Left Handrail (110) on the Left Collar.
Attach the Left Handrail (110) with two 3/8" x
1 1/4" Bolts (7) and two 3/8" Star Washers (9).
Firmly tighten the Bolts.
Tighten two #8 x 3/4" Screws (12) into the Left
Collar (75).
8. Insert the Upright Wire (79) through the Right
Collar (84). Slide the Right Collar onto the Right
Upright (81).
Hold the Right Handrail (109) near the Right
Upright (81). Insert the Upright Wire (79) into the
hole in the bottom of the Right Handrail and pull
it out of the large hole in the side of the Right
Handrail.
8
Plastic Tie
110
79
75
76
Large
Hole
16
106
16
9
12
7
106
See the inset drawing. Insert the included plastic tie through the holes in the Right Handrail
(109) as shown. Look inside the Right Handrail.
Make sure that the plastic tie holds the
Upright Wire (79) to the side as shown in the
inset drawing. Tighten the plastic tie.
Press a Front Handrail Cap (106) into the Right
Handrail (109). Attach the Front Handrail Cap
with a #8 x 3/4" Endcap Screw (16).
Attach the Right Handrail (109) with two 3/8" x 1
1/4" Bolts (7) and two 3/8" Star Washers (9).
Firmly tighten the Bolts.
Tighten two #8 x 3/4" Screws (12) into the Right
Collar (84).
7
9
84
109
12
Hole
Tie
81
109
79
84
Hole
10
Page 11
9. Attach the Pulse Bar Bottom (15) to the
Handrails (109, 110) with two #10 x 3/4" Screws
(5) and two #10 Star Washers (27).
emove the long tie from the Upright Wire (79).
R
9
110
27
5
Long Tie
10. With the help of a second person, hold the console assembly near the Right Handrail (109) and
the Left Handrail (not shown).
Connect the Upright Wire (79) to the console
wire. See the inset drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and try
again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN YOU TURN ON THE
POWER. Insert the connectors and the excess
wire into the Right Handrail (109).
10
109
15
Console
Wire
79
109
Console
5
27
Console
Assembly
Wire
79
11. Connect the console ground wire to the handrail
ground wire.
Set the console assembly on the Handrails
(109, 110). Make sure that the wires are not
pinched. Attach the console assembly with ten
#8 x 3/4" Screws (12). Start all the Screws be-
fore tightening any of them.
Cut the plastic tie off the Right Handrail (109).
See steps 4 and 6. Firmly tighten the 3/8" x 4"
Bolts (6).
11
11
12
109
Console Assembly
Ground Wires
Plastic
Tie
12
12
12
12
79
110
12
12
Page 12
12. Raise the Frame (51) to the position shown.
Have a second person hold the Frame until
this step is completed.
Orient the Storage Latch (48) so that the large
barrel and the Latch Knob (49) are in the positions shown. Attach the lower end of the Storage
atch to the bracket on the Base (86) with a 3/8"
L
x 2" Bolt (4) and a 3/8" Nut (8).
Attach the upper end of the Storage Latch (48)
to the bracket on the Frame (51) with a 3/8" x 2"
Bolt (4) and a 3/8" Nut (8). Note: It may be necessary to move the Frame back and forth to
align the Storage Latch with the bracket.
2
1
1
5
8
4
48
49
Large
Barrel
Lower the Frame (51) (see HOW TO LOWER
86
THE TREADMILL FOR USE on page 21).
8
4
13. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used
to adjust the walking belt (see pages 23 and 24).
If you purchase the optional chest pulse sensor (see page 19), follow the steps below to install the receiver included with the chest pulse sensor.
1. Make sure that the power cord is unplugged.
Remove the indicated 4.2 x 16mm Screw (3)
96
and the Access Door (105) from the Console
Base (96).
2. Connect the wire on the receiver to the indicated wire extending from the Console Base
(96). Hold the receiver so the antenna is ori-
ented as shown and is facing the Console
Base. Attach the receiver to the plastic posts on
the Access Door (105) with the two included
small screws.
Small
Screws
Wire
Receiver
3. Make sure that no wires are pinched.
Reattach the Access Door (105) with the #8 x
3/4" Screw (12). Discard the other wires included with the receiver.
Antenna
105
3
12
Page 13
OPERATION AND ADJUSTMENT
HE PRE-LUBRICATED WALKING BELT
T
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply sil-
cone spray or other substances to the walking
i
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
ric shock. This product is equipped with a cord having
t
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
utlet that is properly installed and grounded in
o
accordance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets.
HOW TO PLUG IN THE POWER CORD
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeʼs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call the telephone
number on the front cover of this manual and order
part number 146148, or see your local electronics
store.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
1
Grounded Outlet
2
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Grounding Pin
Grounding Plug
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may slow, accelerate, or stop unexpectedly, which
may result in a fall and serious injury.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
Grounding Plug
13
Page 14
CONSOLE DIAGRAM
usic Port for iPod
M
Key
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to make your workouts more effective and enjoyable.
When you use the manual mode, you can change the
speed and incline of the treadmill with the touch of a
button. As you exercise, the console will display instant
exercise feedback. You can even measure your heart
rate using the handgrip pulse sensor or the optional
chest pulse sensor (see page 19).
You can customize your workout using one of the four
calorie goal workouts in the weight loss center. In addition, the console features eight iFit classic workouts.
Each workout automatically controls the speed and incline of the treadmill as it guides you through an effective exercise session.
You can even listen to your favorite workout music or
audio books with the consoleʼs premium stereo sound
system while you get in shape. This product has been
designed specifically to work with iPod and has been
Clip
certified by the developer to meet Apple performance
standards.
To turn on the power, see page 15. To use the manual mode, see page 15. To use the weight loss center, see page 17. To use a classic workout, see
page 18. To use the stereo sound system, see page
19. To use the information mode, see page 19.
IMPORTANT: If there are sheets of clear plastic on
the console, remove the plastic. To prevent damage to the walking platform, wear clean athletic
shoes while using the treadmill. The first time you
use the treadmill, observe the alignment of the
walking belt, and center the walking belt if necessary (see page 24).
Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of measurement, see THE INFORMATION MODE on page
19. Note: For simplicity, all instructions in this section
refer to miles.
14
Page 15
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
IMPORTANT: If the treadmill has been exposed to
old temperatures, allow it to warm to room tem-
c
perature before turning on the power. If you do not
o this, you may damage the console displays or
d
other electrical components.
Plug in the power cord (see
page 13). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
Reset
power cord. Switch the circuit breaker to the reset position.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is displayed in a store. If the displays light as soon as
you plug in the power cord and switch the reset/off
circuit breaker to the reset position, the demo
mode is turned on. To turn off the demo mode,
hold down the Stop button for a few seconds. If the
displays remain lit, see THE INFORMATION MODE
on page 19 to turn off the demo mode.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 14)
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the displays will light. IMPORTANT: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the position of the clip.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
When the key is inserted, the manual
mode will be selected. If you have
selected the weight
loss center or a
classic workout, remove the key and then reinsert
it.
3. Start the walking belt.
To start the walking belt, press the Start button, the
Speed increase button, or one of the Precision
Quick Speed buttons numbered 1 through 10.
If you press the Start button or the Speed increase
button, the walking belt will begin to move at 1 mph.
As you exercise, change the speed of the walking
belt as desired by pressing the Speed increase and
decrease buttons. Each time you press one of the
buttons, the speed setting will change by 0.1 mph; if
you hold down the button, the speed setting will
change in increments of 0.5 mph. Note: After you
press a button, it may take a moment for the walking belt to reach the selected speed setting.
If you press one of the numbered Precision Quick
Speed buttons, the walking belt will gradually
change speed until it reaches the selected speed
setting. To select a speed setting that includes a
decimal—such as 3.5 mph—press two numbered
buttons in succession. For example, to select a
speed setting of 3.5 mph, press the 3 button and
then immediately press the 5 button.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button or
the Speed increase button.
15
Page 16
4. Change the incline of the treadmill as desired.
6. Measure your heart rate if desired.
To change the incline of the treadmill, press the
ncline increase or decrease button. Each time you
I
press the Incline increase or decrease button, the
ncline will change by 0.5 percent. Note: After you
i
press an incline button, it may take a moment for
the treadmill to reach the selected incline setting.
5. Select a display mode and monitor your
progress with the display.
When the manual mode is selected, the console
offers two display modes. Press the Display button
repeatedly to select the desired display mode.
As you walk or run on the treadmill, the display can
show the following workout information:
• A 1/4-mile (400 meter) track.
• The number of laps you have completed.
• The elapsed time.
• The distance that you have walked or run.
• The approximate number of calories you have
burned.
• The incline level of the treadmill.
• The speed of the walking belt.
Regardless of which display mode you select, the
speed or incline setting will appear in the display
for a few seconds each time you change the setting. In addition, your heart rate will appear in the
display each time you use the handgrip pulse sensor or the optional chest pulse sensor.
To reset the console, press the Stop button, remove the key, and then reinsert the key.
Note: If you use the handgrip pulse sensor and
he optional chest pulse sensor at the same
t
time, the display will not show your heart rate
ccurately. See page 19 for information on the op-
a
tional chest pulse sensor.
Before using the
handgrip pulse
sensor, remove
the sheets of
clear plastic from
the metal contacts on the pulse
Contacts
bar. In addition,
make sure that
your hands are clean.
To measure your heart rate, stand on the foot
rails and hold the pulse bar with your palms on the
metal contacts. Avoid moving your hands. When
your pulse is detected, a heart symbol will flash in
the display each time your heart beats and then
your heart rate will be shown. For the most accu-
rate heart rate reading, continue to hold the
contacts for about 15 seconds.
7. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting or you may damage the treadmill when you
fold it to the storage position. Next, remove the
key from the console and put it in a secure place.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmillʼs electrical components may wear prematurely.
16
Page 17
HOW TO USE THE WEIGHT LOSS CENTER
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 15.
2. Select a calorie goal workout.
To use a calorie goal workout, press the Weight
Loss Center button.
Input your weight, the number of calories you wish
to burn, and the desired workout duration by repeatedly pressing the increase or decrease button
next to the Weight Loss Center button. Hold down
the increase or decrease button to rapidly change
your weight or the workout duration. Press the
Enter button after each selection. Note: Once you
have entered your weight, it will be saved in memory. The profiles on the console represent the
speed settings of the workout.
Incline buttons; however, when the next segment
begins, the treadmill will automatically adjust to
the speed and incline settings for the next seg-
ent.
m
o stop the workout at any time, press the Stop
T
button. To restart the workout, press the Start button or the Speed increase button. The walking belt
will begin to move at 1 mph. When the next segment of the workout begins, the treadmill will automatically adjust to the speed and incline settings
for the next segment.
4. Select a display mode and monitor your
progress with the display.
When the weight loss center is selected, the console offers two display modes. Press the Display
button repeatedly to select the desired display
mode. The display can show the following workout
information:
3. Start the walking belt.
Press the Start button or the Speed increase button
to start the workout. A moment after you press the
button, the treadmill will automatically adjust to the
first speed and incline settings of the workout. Hold
the handrails and begin walking.
Each workout is divided into segments. One speed
setting and one incline setting are programmed for
each segment. Note: The same speed setting
and/or incline setting may be programmed for consecutive segments.
Tones will sound at the end of each segment. If a
different speed setting and/or incline setting is programmed for the second segment, the speed setting and/or incline setting will flash in the display for
a moment to alert you. The treadmill will then automatically adjust to the speed and incline settings
for the second segment.
The workout will continue in this way until the last
segment ends. The walking belt will then slow to a
stop.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the Speed or
• Workout informa-
tion bars that
show your
progress during
the workout.
• A profile of the speed settings of the workout.
The arrow below the profile will indicate your
progress.
• The time remaining in the workout.
• The distance that you have walked or run.
• The approximate number of calories you have
burned.
• The incline level of the treadmill.
• The speed of the walking belt.
5. Measure your heart rate if desired.
See step 6 on page 16.
6. When you are finished exercising, remove the
key from the console.
See step 7 on page 16.
17
Page 18
HOW TO USE A CLASSIC WORKOUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 15.
incline setting will flash in the display for a moment
to alert you. The treadmill will then automatically
adjust to the speed and incline settings for the sec-
nd segment and the arrow will move one segment
o
to the right.
2. Select a classic workout.
To select a classic
workout, press the
Classic Workouts
button repeatedly.
The duration, the
maximum speed
setting, the maximum incline setting, and the number of the workout will appear in the display. In addition, a profile of the speed settings of the workout
will appear.
3. Start the walking belt.
Press the Start button or the Speed increase button
to start the workout. A moment after you press the
button, the treadmill will automatically adjust to the
first speed and incline settings of the workout. Hold
the handrails and begin walking.
Each workout is divided into one-minute segments.
One speed setting and one incline setting are programmed for each segment. Note: The same
speed setting and/or incline setting may be programmed for consecutive segments.
The workout will continue in this way until the arrow
reaches the right end of the profile and the last
segment ends. The walking belt will then slow to a
stop.
If the speed or incline setting for the current segment is too high or too low, you can override the
setting by pressing the Speed or Incline buttons;
however, when the next segment begins, the
treadmill will automatically adjust to the speed
and incline settings for the next segment.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start button. The walking belt will begin to move at 1 mph.
When the next segment of the workout begins, the
treadmill will automatically adjust to the speed and
incline settings for the next segment.
4. Select a display mode and monitor your
progress with the display.
See step 5 on page 16. Note: The display will show
a profile of the speed settings of the workout instead of a track and the number of laps you have
completed.
A profile of the speed settings of the workout will
appear in the display. A small arrow below the profile will indicate your progress.
At the end of the first one-minute segment of the
workout, a series of tones will sound. If a different
speed setting and/or incline setting is programmed
for the second segment, the speed setting and/or
5. Measure your heart rate if desired.
See step 6 on page 16.
6. When you are finished exercising, remove the
key from the console.
See step 7 on page 16.
18
Page 19
HOW TO USE THE STEREO SOUND SYSTEM
This product has been designed specifically to work
ith iPod and has been certified by the developer to
w
meet Apple performance standards. To play music or
udio books through the consoleʼs stereo speakers,
a
you must connect your iPod, MP3 player, CD player,
or other personal audio player to the console through
the audio jack or through the music port for iPod. The
music port will charge your iPod while you use it.
To use the audio jack, locate the audio wire and plug it
into the audio jack near the speakers. Then, plug the
audio wire into a jack on your iPod, MP3 player, CD
player, or other personal audio player. Make sure that
the audio wire is fully plugged in.
To use the music port for iPod, you need an iFit
Universal iPod Connector (not included). To purchase
an iFit Universal iPod Connector, please call the
telephone number on the front cover of this manual. Plug one end into the music port near the speaker
and the other end into your iPod. Make sure that the
iFit Universal iPod Connector is fully plugged in.
The display will show
the total number of
hours the treadmill has
een used.
b
The display will also show the total number of miles or
kilometers that the walking belt has moved.
The word ENGLISH for miles or METRIC for kilometers
will appear in the display. Press the Speed increase
button to change the unit of measurement if desired.
The console features a display demo mode, designed
to be used if the treadmill is displayed in a store. While
the demo mode is turned on, the console will function
normally when you plug in the power cord, switch the
reset/off circuit breaker to the reset position, and insert
the key into the console. However, when you remove
the key, the displays will remain lit, although the buttons will not function. If the demo mode is turned on,
the word ON will appear in the display while the information mode is selected. To turn on or turn off the demo
mode, press the Speed decrease button.
Next, press the Play button on your iPod, MP3 player,
CD player, or other personal audio player. Adjust the
volume on your personal audio player or press the
Volume increase and decrease buttons on the console.
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat surface instead of on the console.
THE INFORMATION MODE
The console features an information mode that keeps
track of the total distance that the walking belt has
moved and the total number of hours that the treadmill
has been used. The information mode also allows you
to select a measurement system of miles or kilometers, and to turn on and turn off the display demo
mode.
To select the information mode, hold down the Stop
button while inserting the key into the console and then
release the Stop button. When the information mode is
selected, the following information will be shown:
To exit the information mode, remove the key from the
console.
THE OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor offers hands-free operation as it tracks your heart rate during your workouts.
To purchase the optional chest pulse sensor, call
the telephone number on the front cover of this
manual.
19
Page 20
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
owest position. If you do not do this, you may damage the
l
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
lbs. (20 kg) to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight as you raise the frame. Raise the frame
about halfway to the vertical position.
2. Raise the frame until the latch knob locks into the storage
position. Make sure that the latch knob is locked in the
storage position.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage
position in temperatures above 85° F (30° C).
rame
F
Frame
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch
knob is locked in the storage position.
1. Hold a handrail and the frame and place one foot against
one of the wheels.
2. Tip the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface. Do not pull back on the frame.
3. Place one foot against a wheel, and carefully lower the
treadmill until it is resting in the storage position.
Latch Knob
Frame
Handrail
Wheel
20
Page 21
HOW TO LOWER THE TREADMILL FOR USE
. Hold the upper end of the treadmill with your right hand.
1
Pull the latch knob to the left and hold it. It may be necessary to push the frame forward as you pull the knob to
the left. Pivot the frame downward and release the latch
knob.
2. Hold the metal frame firmly with both hands and lower
it to the floor. CAUTION: Do not grip only the plastic
foot rails or drop the frame to the floor. Bend your
legs and keep your back straight.
Latch Knob
Frame
21
Page 22
TROUBLESHOOTING
ost treadmill problems can be solved by following the simple steps below. Find the symptom that
M
applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 13). Use only a single-outlet surge suppressor that meets all of the specifications described on page 13. IMPORTANT: The treadmill is not
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
PROBLEM:The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 19 to turn off the demo mode.
c
Tripped Reset
PROBLEM:The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG
THE POWER CORD. With the help of a second
person, carefully tip down the Uprights (76, 81).
There may be two Belly Pan Screws (A) in the bottom of the Belly Pan (74). If there are, remove them.
Note: A Phillips screwdriver with a shaft at least 5
in. (13 cm) long is required. Then, raise the
Uprights.
22
a
81
76
74
A
A
Page 23
Remove the three #8 x 3/4" Screws (12) and carefully pivot the Motor Hood (59) off.
Locate the Reed Switch (72) and the Magnet (45)
on the left side of the Pulley (46). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If nec-
essary, loosen the #8 x 3/4" Truss Head Screw
(17), move the Reed Switch slightly, and then
retighten the Screw. Reattach the Motor Hood (not
shown) with the #8 x 3/4" Screws (not shown).
Reattach the Belly Pan Screws (not shown) if necessary. Run the treadmill for a few minutes to
check for a correct speed reading.
1/8 in.
Top
View
59
17
72
12
45
46
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 13.
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may become damaged. Remove the key and UNPLUG
b
2–3 in.
THE POWER CORD. Using the hex key, turn both
idler roller bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walk-
Idler Roller Bolts
ing belt is properly tightened.
c. If the walking belt still slows when walked on, see the front cover of this manual.
23
Page 24
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the
ey and UNPLUG THE POWER CORD. If the
k
walking belt has shifted to the left, use the hex
ey to turn the left idler roller bolt clockwise 1/2 of a
k
turn; if the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn. Be
careful not to overtighten the walking belt. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first re-
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn both idler roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each
edge of the walking belt 2 to 3 in. (5 to 7 cm) off
the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for
a few minutes. Repeat until the walking belt is
properly tightened.
a
b
24
Page 25
EXERCISE GUIDELINES
WARNING: Before beginning this
r any exercise program, consult your physi-
o
cian. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is intended only as an exercise aid in determining
heart rate trends in general.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
WORKOUT GUIDELINES
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
25
Page 26
PART LIST—Model No. PFTL49609.0 R0310A
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty. Description Key No. Qty. Description
15#8 x 3/4" Tek Screw
24#8 x 1" Tek Screw
11 4.2 x 16mm Screw
3
443/8" x 2" Bolt
52#10 x 3/4" Screw
643/8" x 4" Bolt
743/8" x 1 1/4" Bolt
843/8" Nut
983/8" Star Washer
10 8 #8 x 1/2" Screw
11 2 #8 x 1/2" Pan Head Screw
12 17 #8 x 3/4" Screw
13 2 Base Pad Spacer
14 4 #8 x 1/2" Belt Guide Screw
15 1 Pulse Bar Bottom
16 2 #8 x 3/4" Endcap Screw
17 11 #8 x 3/4" Truss Head Screw
18 2 #8 x 1 1/2" Screw
19 2 5/16" x 1 1/2" Bolt
20 2 5/16" x 5/8" Bolt
21 2 3/8" x 1" Bolt
22 1 1/4" x 1" Bolt
23 2 Rear Roller Bolt
24 1 3/8" x 1 1/2" Bolt
25 1 3/8" x 1 3/4" Bolt
26 2 3/8" x 3/4" Bolt
27 2 #10 Star Washer
28 8 #12 x 1 1/4" Screw
29 2 Drive Motor Bolt
30 2 1/4" Flat Washer
31 2 1/4" Lock Washer
32 4 3/8" Jam Nut
33 4 5/16" Flange Nut
34 3 Hood Clip
35 6 #3 x 1/4" Screw
36 2 Foot Rail Decal
37 1 Left Foot Rail
38 1 Warning Decal
39 2 Platform Cushion
40 1 Walking Platform
41 1 Walking Belt
42 2 Belt Guide
43 2 Frame Cap
44 2 Frame Spacer
45 1 Magnet
46 1 Drive Roller/Pulley
47 1 Latch Cap
48 1 Storage Latch
49 1 Latch Knob
50 1 Right Foot Rail
51 1 Frame
52 2 Roller Bracket
3 1 Rear Roller Ground Wire
5
54 1 Right Rear Foot
55 1 Left Rear Foot
56 1 Rear Roller
57 1 Hex Key
58 2 Handrail Cap
59 1 Motor Hood
60 1 Hood Accent
61 1 Lift Frame
62 1 Lift Frame Ground Wire
63 3 Wire Tie
64 1 Drive Motor Belt
65 1 Drive Motor
66 1 Incline Motor Wire
67 1 Controller Ground Wire
68 1 Power Cord
69 1 Grommet
70 1 Reset/Off Circuit Breaker
71 1 Controller
72 1 Reed Switch
73 1 Reed Switch Clamp
74 1 Belly Pan
75 1 Left Collar
76 1 Left Upright
77 1 Incline Motor
78 1 Incline Motor Spacer
79 1 Upright Wire
80 4 Bolt Spacer
81 1 Right Upright
82 2 Base Cap
83 1 Left Upright Spacer
84 1 Right Collar
85 2 Caution Decal
86 1 Base
87 2 Wheel
88 4 Base Pad
89 1 Right Upright Spacer
90 2 15 1/2" Wire Tie
91 2 Releasable Tie
92 12 8" Wire Tie
93 1 Console
94 1 Left Tray
95 1 Right Tray
96 1 Console Base
97 1 Right Top Pulse Plate
98 1 Right Bottom Pulse Plate
99 1 Key Board
100 1 Left Top Pulse Plate
26
Page 27
Key No. Qty. Description Key No. Qty. Description
101 1 Left Bottom Pulse Plate
02 2 Plastic Tie
1
103 1 Audio Wire
104 0 Not Used
105 1 Access Door
06 2 Front Handrail Cap
1
107 1 Key/Clip
08 4 Console Clamp
1
109 1 Right Handrail
10 1 Left Handrail
1
111 1 Pulse Bar Ground Wire
*–8" Blue Wire, M/F
*–10" Blue Wire, 2F
*
– 12" Red Wire, M/F
*–10" Black Wire, M/F
*
– Userʼs Manual
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
27
Page 28
4
49
48
8
17
19
19
20
23
23
31
30
31
30
54
10
14
14
42
42
28
28
28
43
28
28
28
28
28
36
37
33
33
33
22
45
43
44
33
39
40
38
41
46
50
36
56
39
51
52
52
44
55
57
18
47
53
17
17
17
17
18
17
17
20
10
4
8
EXPLODED DRAWING A—Model No. PFTL49609.0 R0310A
28
Page 29
1
1
1
73
17
72
34
34
1
2
11
10
10
68
69
70
10
67
59
63
74
71
62
21
21
61
60
29
65
64
34
1
10
12
12
EXPLODED DRAWING B—Model No. PFTL49609.0 R0310A
29
Page 30
88
2
88
2
88
2
4
87
87
4
6
9
9
7
9
7
9
25
24
32
32
77
26
26
32
32
82
82
76
81
86
85
83
89
85
92
91
80
80
80
88
2
78
90
79
79
12
84
12
75
8
8
9
6
6
66
13
13
EXPLODED DRAWING C—Model No. PFTL49609.0 R0310A
30
Page 31
93
3
103
107
10
111
12
102
94
9
5
106
110
58
12
12
12
12
12
3
3
3
3
3
35
99
35
35
96
15
5
35
109
98
97
101
100
108
3
5
105
106
12
58
16
16
27
27
EXPLODED DRAWING D—Model No. PFTL49609.0 R0310A
31
Page 32
ORDERING REPLACEMENT PARTS
o order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro-
T
vide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
IMPORTANT: You must register this product within 30 days of the purchase date to avoid added
fees for service needed under warranty. Go to www.proformservice.com/registration.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The drive motor is warranted for twenty-five (25)
years from the date of purchase. Parts and labor are warranted for ninety (90) days from the date of purchase.
This warranty extends only to the original purchaser. ICONʼs obligation under this warranty is limited to
repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customerʼs responsibility. For
replacement parts shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to any damage to a product caused by or attributable to freight damage,
abuse, misuse, improper or abnormal usage, or repairs not provided by an ICON authorized service center; to products used for commercial or rental purposes or as store display models; or to products transported or purchased outside the US. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 282922 R0310A Printed in China © 2010 ICON IP, Inc.
Loading...