Prima LPR661, PR659 Technical & Service Manual
Specification 1
Test program 36-39
Theory of parts 19-33
Contents
Function Description 4-18
Inspection 40-43
Location 19
PCB 19-21
Inlet valve 22-24
Drain pump 25-26
Heater 27-28
Washing pump 29-30
Procedure 37
Error code 38-39
Water circuit 4-5
Circuit schematic 6
Exploded View & Part List 7-18
Technical Service Manual
D
i
s
h
w
a
s
h
e
r
Pressure switch 31
NTC 32-33
SAFETY NOTICE
This documentation is only intended for qualified technicians who are
aware of the respective safety regulations.
Model
LPR661
LPR659
Operation instructions 2
Installation instructions 3
Flowmeter 34-35
Specifications
Models：
220-240V, 50Hz
0.04MPa-1.0MPa
below 60℃
12
Models：
220-240V, 50Hz
0.04MPa-1.0MPa
below 60℃
8
Supply water pressure
Supply water temperature
Settings
LPR661
Electrical supply
Supply water pressure
Supply water temperature
Settings
LPR659
Electrical supply
1
Operation instructions
2
Control Panel
5
Half washing button:To select half washing.
(Optional half washing means that the lower spray arm
does not run, so you should load the upper basket only).
Power on light: To come on when Power ON/OFF
button is pressed down.
11
2
3
4
ON/OFF Button: Will turn on/off the power supply.
6
Program button: To select washing program
when the button is pressed.
Delayed Start Button: Press this button to set the
delayed hours for washing. You can delay the start
of washing up to 24 hours. One press on this
button delays the start of washing by one hour.
11
2
3
4
5
6
Display Window: delay time, running indicator,
fault codes etc.
On
Off
P
rog.
Delay
Di617
1
2
/
/
NOTE:
Turning on the Appliance
Starting a wash cycle...
Draw out the lower and upper basket, load the dishes and
push them back. It is commended that loading the lower
basket first, than the upper one (see the section entitled
“Loading the Dishwasher”).
Pour in the detergent (see the section entitled “Salt,
Detergent and Rinse Aid”).
Insert the plug into the socket. The power supply is 220-240
VAC 50 HZ, the specification of the socket is 10 A 250 VAC.
Make sure that the water supply is turned on to full pressure.
Open the door,press the ON/OFF button,and the ON/OFF light
will turn on.
Pre
ss the "prog. "button to select a desired "Wash cycle".(see
the section entitled."Wash Cycle Table".)
With a little force to ensure the door is properly closed.
NOTE: A click will be heard when the door is closed perfectly.
When the washing is over, you can shut off the switch by
pressing ON/OFF button.
Change the Programme . . .
Premise: A cycle that is underway can only be modified if it
has only been running for a short time. Otherwise, the detergent
may have already been released, and the appliance may have
already drained the wash water. If this is the case, the detergent
dispenser must be refilled (see the section entitled " Loading the
Detergent " ).
Open the door,Press current prog. button more than three
seconds to cancel the program ,then you can change the
program to the desired cycle setting (see the section entitled
" Starting a wash cycle. . . " ). Then, close the door.
NOTE: If you open the door when washing, the machine
will pause. When you close the door , the machine will
resume working after 10 seconds.
1
2
3
4
5
6
If all the lights begin to glimmer, this indicates the machine has developed a fault,
please turn off the main power and water supply before calling a service agent.
2
I
nstallation instructions
3
w
a
s
h
i
n
g
p
u
m
p
w
a
s
h
i
n
g
p
u
m
p
pr
essure
switch
p
r
e
s
s
u
r
e
s
w
i
t
c
h
dr
ain
pu
m
b
d
r
a
i
n
p
u
m
b
dr
ain
ho
s
e
d
r
a
i
n
h
o
s
e
ov
er
flow
switch
o
v
e
r
f
l
o
w
s
w
i
t
c
h
ai
r
breaker
a
i
r
b
r
e
a
k
e
r
in
let
valve
i
n
l
e
t
v
a
l
v
e
in
let
ho
s
e
i
n
l
e
t
h
o
s
e
Regeneration
water
route
R
e
g
e
n
e
r
a
t
i
o
n
w
a
t
e
r
r
o
u
t
e
u
p
p
e
r
s
p
r
a
y
a
r
m
u
p
p
e
r
s
p
r
a
y
a
r
m
t
o
p
s
p
r
a
y
t
o
p
s
p
r
a
y
t
u
b
e
t
u
b
e
Inlet
water
r
o
u
te
I
n
l
e
t
w
a
t
e
r
r
o
u
t
e
up
per
spray
a
r
m
u
p
p
e
r
s
p
r
a
y
a
r
m
so
ftener
s
o
f
t
e
n
e
r
W
a
t
e
r c
i
r
c
u
i
t s
c
h
e
m
e
regeneration valver
e
g
e
n
e
r
a
t
i
o
n
v
a
l
v
e
Cycle
water
r
o
u
te
C
y
c
l
e
w
a
t
e
r
r
o
u
t
e
Drain
water
r
o
u
te
D
r
a
i
n
w
a
t
e
r
r
o
u
t
e
Water Circuit Function Description->
4
F
o
r
a
l
l
t
h
e
m
o
d
e
l
s t
h
i
s m
a
n
u
a
l m
e
n
t
i
o
n
e
d
Process of water inlet (indicated by magenta route)
Process of cycle washing (indicated by blue route)
Process of regeneration (indicated by green route)
In this process, regeneration water route is cut off, main water route is open. The water in the main water
route is softened when pass through the softener, and then enter in the tub. During this phase, some of inlet
water will be stored in the air breaker to be regenerating water.
Cycle washing action is driven by washing pump motor. Water can obtain the power during it passing through
the working washing pump, then be pumped into spray arm, pass from spray arm nozzles, over the dishes,
into sump ,where connect to washing pump, and to get in the next water cycle.
Regeneration valve is open, the regenerating water dissolve salt in the salt chamber of softener, and then
enter in the resin tank to reactivate the resin.
Water Circuit Function Description->
5
Circuit Schematic Function Description->
Circuit schematic diagram
6
LPR661 LPR659
Exploded view Function Description->
7
LPR661
Please Note: Exploded view and part list of each model have
some different visions, so please refer to newest vision Midea
sent you.
Exploded view Function Description->
8
LPR 661
Exploded view Function Description->
9
LPR 661
Part List Function Description->
10
LPR661
Serial
Number
Code Description Quantity
1001 673000900249 External pipe 1
1002 673001500005 O Ring I 31. 5X3.55 3
1003 673001800364 Guide casing 1
1004 673001600021 External pipe nut 1
1005 673001900016 Water dispenser 1
1006 673000300067 Upper sprayer 1
1007 673000900089 Upper sprayer pipe 1
1009 673001300041 Upper sprayer holder block 1
1010 673002300002 Float holder 1
1011 672000900012 Screw ST2.9x22 1
1012 673002300003 Float 1
1013 674000300060 Micro switch 1
1016 673002500047 Micro filter 1
1017 673001600022 Sump nut 1
1018 673001500016 Sump gas ket 1
1019 673000700081 Sump 1
1020 672000700028 Clamp 12.7 1.8 1
1022 673000900073 PVC hos e 1
1027 674000600106 Drain pump 1
1029 673002200043 Salt filler 1
1030 673002800050 Softener cover assembly 1
1031 673001700053 Softener cover gasket 1
1032 673001600039 Softener nut 1
1033 673001700001 Softener gasket 1
1034 674000700021 Softener 1
1036 672000700029 Clamp 14.5 1.8 1
1037 673006200003 Drain hose hook 1
1038 673001500002 Drain hose holder 1
1039 673000900186 Drain hose 1
1042 674000000092 Power cord 1
1043 674000200002 Iniet valve 1
1045 673000900060 inlet hose assem bly 1
1046 673000900026 Regeneration hose 1
1048 673000900024 Inlet hos e of air breather 1
1051 673001600055 Air breather nut 2
1054 673002700008 AWECO Flowmeter 1
1064 672000600013 Lower sprayer 1
1070 674000600047 Washing pump 1
Part List Function Description->
11
LPR661
Serial
Number
Code Description Quantity
1083 673000900045 Bend connect hose 1
1085 673001400025 Heating element support 1
1086 674001100039 Heating elements 1
1088 673001600024 Water inlet nut 1
1089 673001500019 Water inlet gasket 1
1091 673002600035 Water inlet 1
1093 674000900038 Sensing device 1
1113 673002500048 plane filter 1
1114 673001300137
Scran collection 1
1115 674000300079 Pressure switch 1
1116 673001400083 power cord clasper 1
1117 674000300067 pressure switch assembly for heating elements 1
2001 673002000042 Door edge guard piece 2
2002 672002200150 Inner door 1
2004 672001700002 Dispenser bracket 2
2005 674000800032 Dispenser 1
2006 674000100453 Wiring harness 1
2008 672000500006 Ring Φ64
2009 672001300029 Left hinge 1
2010 672001200012 Joint pin 2
2011 672001300030 Right hinge 1
2012 672001300024 Door gemel assembly 1
2013 672000100008 Door spring 2
2017 672001800315 Outer door 1
2018 673000404251 Front panel 1
2023 673001800513 Handle assembly 1
2027 674000300065 Power switch 1
2028 674000400011 Red pilot lamp 1
2034 674001020203 Control board 1
2035 672000300989 Control panel film 1
2036 673002400095 Control board box 1
2039 673002800090 Window 1
2040 673001800365 Screw sleev e 2
2041 673000700005 Sleeve cover 2
2053 673002800041 Control panel cover 1
2080 672000100012 button spring 3
2950 673000800906 Power button 1
2951 673000800905 Program key 3
3001 672001600212 Left side panel 1
3003 672002100058 Lower rear crosspiece 1
Part List Function Description->
12
LPR661
Serial
Number
Code Description Quantity
3005 672001500008 Upper rear crosspiece 1
3006 673001300061 door clamp 1
3007 672001400039 door lock 1
3009 672001500246 Upper front crosspiece 1
3010 673001700057 Tank gasket 1
3011 672002100057
Upright right assembly 1
3012 672001600211 Right panel 1
3013 673001300102 Upper basket cup holder 4
3014 673002200099 Cutlery bas ket 1
3017 672000800210 Lower basket 1
3018 672000800255
Upper basket
1
3021 673001300044 Rail block 2
3022 672001700005 Rail 2
3023 673001400056 Rail support ass embly 4
3027 672001500303
Lower front crosspiece 1
3029 672002000066 Tray assembly 1
3032 673001700010 Tank band bracing block 2
3033 672001500202 Lower rear crosspiece 1
3034 672001500007 Middle rear crosspiece 1
3035 673002200079 Measurable spoon 1
3048 672001100004 Adjust steel rope 2
3049 672002300002 Adjust nut 2
3050 673001300012 Top board hook 2
3051 672001100003 Adjust screw 2
3052 673001400145
Right adjuster holder assem bly 1
3053 672001400005 Front foot 2
3054 673003000001 slide 2
3055 672001100002 Adjustable pole 2
3056 673001400146 Left adjuster holder assembly 1
3057 672001400006 Back foot 2
3079 673002200091
3 in 1 tablet container
1
1035+1047 673000900224 Softener pipe 2
1071+1072 672000200054 Washing m o tor support 1
1074- a 673000900140 Connec t hose a 1
1074- b 673000900182 Connec t hose b 1
C5004 673006200004 rinsing agent cup 1
OTK 175 672000700004 OTK 175 4
OTK 286 672000700003 OTK 286 1
OTK 310 672000700001 OTK 310 6
OTK 396 672000700007 OTK 396 3
Exploded view Function Description->
13
LPR659
Loading...