InstructionSheet
InstructionSheet
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker.
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
INSTALLATION INSTRUCTIONS
Housing Installation
Figure 1
Support Frame
(By Others)
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .03424500
All servicing or relamping must be performed by
ALCF-1, 4, 5, and 6
www.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ET
Housing
Adjustable Mounting
Bracket (2)
Conduit
(By Others)
Profile Trim
Figure 2
Housing
Adjustable
Mounting
Bracket (2)
Conduit
Entry
Trim
Profile
(Wet or Drywall
Construction)
Fastener (Nail)
(By Others)
Conduit
(By Others)
1. Install the housing by nailing the mounting brackets on
the housing to the frame support as shown in Fig. 1, or
frame in the housing as desired for wet or dry wall
construction.
2. Adjust the mounting brackets to locate the housing as
required for profile trim (Fig. 2).
3. Install the conduit (by others) to align with one of three
7/8" diameter knockouts located on the sides and
bottom of housing. Remove the wingnut retaining the
socket mounting plate and lift out plate.
4. When installed in concrete pour or mortar and in a
situation where direct water exposure is frequent, the
concrete or mortar is to be suitably treated with a
sealing or repelling agent to insure that the fixture
housing does not remain continuously wet.
101 Corporate Drive • Spartanburg, SC 29303
With representatives of
Copyright 2005, 08/05 revision, All Rights Reserved - Printed in U.S.A.
fices in principal cities throughout North
America.
InstructionSheet
Socket Holder
Plate
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .03424500
www.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ET
Housing
(Installed)
Faceplate
Faceplate Installation
Figure 3
5. Make electrical connections. Connect ground wires to green
ground leads. Connect white (common) to white leads. Connect
power supply (line) to black leads. (see wiring diagram).
For through wiring: replace the J-Box cover (Fig. 4). Replace the
socket mounting plate and install lamp.
pinch wires. Consult a Qualified Electrician for all other
options that require other wiring configurations.
Assemble faceplate to the housing (Figure 3)with two (2) 8-32
6.
flathead screws (provided in packet).
7. To relamp fixture:
ALCF-1 Remove faceplate
ALCF-4, 5, & 6 Loosen thumbscrew and
open faceplate door.
120V
Supply
Wire Nut
(By Others)
WARNING: DO NOT
(WHT)
(BLK)
BALLAST
(BLK)
SOCKET
Wiring Diagram
101 Corporate Drive • Spartanburg, SC 29303
With representatives of
Copyright 2005, 08/05 revision, All Rights Reserved - Printed in U.S.A.
fices in principal cities throughout North
America.
Fig. 4
Loading...