InstructionSheet
InstructionSheet
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124420100
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
INSTALLATION INSTRUCTIONS
79XCP
TRIM INSTALLATION (FIGURE 2):
1. ADJUST SOCKET BRACKET TO PROPER POSITION BY
.
ousing
H
Thick Ceiling
Adjustment
Screw (3)
LOOSENING WING NUT
PAR 30 LAMPS: SLIDE BRACKET TO LOWEST
OWARDS APERTURE) POSITION.
(T
PAR 38 LAMPS: SLIDE BRACKET TO HIGHEST
(AWAY FROM APERTURE) POSITION.
2. TIGHTEN WING NUT SECURELY.
ST832BB SERIES TRIMS:
3. INSTALL TRIM BY LOCATING COIL SPRINGS
IN SLOTS ON HOUSING.
4. INSTALL LAMP.
ST832 SERIES TRIMS:
3. INSTALL LAMP.
4. LOCATE TRIM CLIP RETAINING HOLES ON LIP
OF PLASTER FLANGE. ATTACH TRIM
RETAINING CLIPS (3) TO PLASTER FLANGE.
5. PRESS TRIM INTO APERTURE.
www.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ET
Adjustable
Mounting Bracket (2)
J-Box Covers
Figure 1.
1. Install the fixture in the ceiling using mounting channel, bar stock or 1/2" rigid conduit placed in the adjustable mounting brackets.
The fixture should be installed in such a manner that the weight of the fixture is supported by the mounting channels/bar
stock/rigid conduit and/or hanger wires secured to the building structure.
2. Adjust the fixture so the bottom edge of the plaster flange is flush with the ceiling line by sliding the mounting brackets and secure
using adjusting screws (Fig. 1). Housing may be lowered further to compensatefor thick ceilings by use of the (3) thick ceiling
screws
3. Remove J-Box cover plate. Remove appropriate knockout and assemble appropriate connector for the supply wire used. Connect
ground wires to green ground leads. Connect white (common) to white (leads). Connect power supply (line) to black lead(s).
Reinstall J-Box cover.
WARNING: DO NOT pinch wires between J-Box/ballast cover and J-Box. Consult a Qualified Electrician for all other options
CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND
that require other wiring configurations.
PROPER OPERATIONOF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.
701 Millennium Boulevard • Greenville, SC 29607
With representatives of
Copyright 2007, 02/07 revision, All Rights Reserved - Printed in U.S.A.
fices in principal cities throughout North
Plaster Flange
America.
AR 38 LAMPS
P
PAR 38 LAMPS
Slide
Figure 2.
Loading...