Precision Power FRX 322 User Manual
TM
CLASS
CONTENTS
(click on a topic to view)
Congratulations Functions
Features and Specifications Input
Mounting Troubleshooting
Mounting Frequency Chart
Wiring 3 Way System Design
Wiring Block Diagram
Functions Warranty
FRX322 Electronic Crossover OWNERS MANUAL POWER
Congratulations and thank you.....
for choosing
proudly design, engineer and manufacture audio products at our facility in
Phoenix, Arizona. Our award winning engineering team utilizes innovative
technology to consistently deliver Absolutely State of the Art
sound quality, reliability, and value. This
our commitment to offer you unparalleled versatility and quality for years of
dependable service and listening enjoyment.
PrecisionPower
audio epuipment. At
PrecisionPower
PrecisionPower
TM
performance,
product reflects
we
Service
Do not attempt to service
Performing exploratory surgery on your audio equipment yourself
will void the warranty. Many parts of your
are custom built to our specifications. Our factory parts are not
made available to anyone else nor are they for sale. Our goal
is to make sure that your
sound as good as the day it was purchased. Contact your
authorized
service through
PrecisionPower
PrecisionPo wer
PrecisionPower
PrecisionPower
dealer about obtaining any warranty
.(See Warranty insde back cover)
products yourself.
PrecisionPower
product will always
gear
FOR YOUR RECORDS:
Model
Serial Number
Purchase Date
Caution!
The extended use of a high powered audio system may
result in hearing loss or damage. While
systems are capable of
incredible accuracy, they are also designed for you to
enjoy at more reasonable levels all of the sonic subtleties
created by musicians. Please observe all local sound
ordinances.
"Concert Level"
PrecisionPower
volumes with
BA CK TO CONTENTS
FEATURES / SPECIFICATIONS
3-Way Active Crossover
12dB/octave Slopes
Low Pass Level Control
Input Attenuation Switch
Detented Frequency Selection Controls
Gold RCA Input and Output Connectors
PowerLock
Power, Ground and Remote Connector
PWM Power Supply
Designed and Handcrafted in the USA
Specifications
Signal-to-Noise Ratio >102dB
Total Harmonic Distortion (1KHz, 1VRMS) 0.002%
Input Impedance 10 kΩ
Maximum Output (10 kΩ Load) 8 VRMS
Supply Voltage 11-15 VDC
Crossover Slopes 12 dB/octave
Crossover Frequencies:
Low Pass 40Hz to 500Hz
Front High Pass 40Hz to 5kHz
Rear High Pass 40Hz to 500Hz
Dimensions 6.813" W
0.995" H
3.805" D
1
BA CK TO CONTENTS
Mounting
MOUNTING
To prevent damage to the
FRX-322
while driving, mount it in a
secure place. Choosing the appropriate location will depend
upon your vehicle and the complexity of your system design. Typical
mounting locations for your new
FRX-322
would be in the dash or
center console. Never mount the component in a location that would
subject it to immersion or exposure to water.
Once a location has been chosen, securely mount the
FRX-322
using
the two supplied brackets. There are two different sets of brackets
included with your
322
, as shown above. The other set is used to surface mount, as
FRX-322
. One set is used to flush mount the
FRX-
shown on the next page. The brackets are connected to the equalizer/
preamp by two 6-32 x 1/4" socket head cap screws. We have made
the brackets adjustable to compensate for the uniqueness of each
vehicle. Be Careful! Inspect the area underneath to be sure you are
not drilling into wires, etc. that could be damaged by the drill bit or
screws.
2
BA CK TO CONTENTS
Power
250
300100
0dB
40050
40
500
Low Pass Freq.
- ∞
Low Pass Level
Dimensions
6.813"W
0.995"H
3.805"D
Precision
Power
40
Low Pass Freq.
FRX-322
250
300100
0dB
40050
+5 -10
500
+7 -20
- ∞
+10
Low Pass Level
Front/Rear
Input Connect
Precision
FRX-322
+5 -10
+7 -20
+10
Front/Rear
Input Connect
Power
250
300100
40050
40
500
Low Pass Freq.
Power
FRX-322
Attenuation
-12dB in
Power
FRX-322
Attenuation
-12dB in
0dB
- ∞
Low Pass Level
X 10
FRX-322
+5 -10
+7 -20
+10
Front/Rear
Input Connect
250
40
Front
High Pass Freq.X 10
MOUNTING
Power
R
Low Pass
Output
Made in USA
250
300100
250
40050
300100
40
Front
500
High Pass Freq.
Precision
Power
300100
40050
500
FRX-322
Attenuation
Output
250
40
Rear
High Pass Freq.
Power
-12dB in
R
Low Pass
Made in USA
300100
40050
500
40
Rear
High Pass Freq.
L
40050
500
L
R
Front
L
Input
R
Rear
L
Input
Power
R
Low Pass
Output
Made in USA
250
300100
250
40050
300100
40
Front
500
High Pass Freq.X 10
R
Front
Input
L
40
Rear
High Pass Freq.
R
Rear
Input
40050
500
L
L
High Pass Out
Front
Input
R
R
High Pass Out
Front
L
High Pass Out
Faceplate of bracket blank for installer's
individual needs. We suggest using a
#6 metal screw. Predrill a hole in the
location desired to mount the FRX-322.
R
Front
L
R
Rear
Input
L
R
High Pass Out
Rear
L
Adjustable slots
for screws
R
Rear
L
L
R
High Pass Out
Front
L
High Pass Out
Rear
Adjustable slots
for screws
Bracket can be reversed
for installer's individual needs.
We suggest securing to
surface with a #6 metal screw.
Secure the bracket
to the FRX-322
with the two 6-32x1/4"
screws provided.
Adjustable slots
for screws
Secure the bracket
to the FRX-322
with the two 6-32x1/4"
screws provided.
R
L
Surface mounting
bracket.
3
BA CK TO CONTENTS
Loading...