Prastel UNIK2E230 SK Manual

ISUNIK2E230v2_GB_10_12.doc

WARNING

FOR

TWO

230VAC

MOTORS

ELECTRONIC CONTROL PANEL

UNIK2E230

(COMPLETE)

UNIK2E230SK

(

WITHOUT BOX AND TRANSFORMER)

_ V2

_ V 2

BOX IP 54

The symbol CE conforms with European Directive R&TTE 99/05CE

TECHNICAL INSTALLATION MANUAL

FOR AUTOMATIC

Before installing, thoroughly read this manual that is an integral part of this Kit. Prastel S.p.A. declines any responsibility in the event current standards in the country of installation are not complied with

GATES

UNIK2E230 V2

ENGLISH

ISUNIK2E230v2_GB_10_12.doc

1. INTRODUCTION .......................................................................................... 3

2. MAIN FEATURES ........................................................................................ 3

3. TECHNICAL SPECIFICATIONS .................................................................. 3

4. CONNECTION AND SET UP OF THE CONTROL UNIT ............................. 4

4.1 GENERAL DIAGRAM OF SETTINGS AND CONNECTIONS .................................. 5

4.2 SIMPLIFIED LEARNING PROCEDURE (also see pages 8-10) .............................. 6

4.3 PROFESSIONAL LEARNING PROCEDURE (see also pages 8-10) ...................... 7

5. CONTROL UNIT OPERATING LOGIC (ANALYTIC EXAM) ........................ 8

5.1 PROGRAMMING AND CANCELLATION OF THE REMOTE CONTROLS ............. 8

5.2 OPERATION OF THE SAFETY DEVICES ............................................................... 8

5.3 TRIMMER “FOR”- MOTOR SPEED ......................................................................... 9

5.4 TRIMMER “DEL”- DELAY BETWEEN MOTORS .................................................... 9

5.5 TRIMMER “PAU” - “OPENING AND CLOSING” OPERATING MODE .................. 9

5.6 “PEDESTRIAN OPENING” FUNCTION ................................................................. 11

5.7 TRIMMER “OBS” - “OBSTACLE SENSITIVITY” DETECTION ............................. 11

5.8 FLASHING LIGHT .................................................................................................. 11

5.9 GATE OPEN WARNING LIGHT ............................................................................. 11

5.10 SLOW-DOWN ......................................................................................................... 11

5.11 ELECTRIC LOCK ................................................................................................... 12

5.12 COURTESY LIGHT ................................................................................................. 12

5.13 LOGICAL STOP (STP INPUT) ................................................................................ 12

5.14 CONTROL UNIT MEMORY FAULT ........................................................................ 12

6. SIGNALLING LED ..................................................................................... 12

7. PROGRAMMING THROUGH GTSYSTEM ................................................ 13

8. ACCESSORIES ABSORPTION CHECK INFORMATION ......................... 13

9. TROUBLESHOOTING ............................................................................... 14

SAFETY WARNINGS FOR INSTALLATION AND USE ................................................... 15

UNIK2E230 V2

ENGLISH

ISUNIK2E230v2_GB_10_12.doc

1. INTRODUCTION

UNIK2E230 is a universal self-learning control unit especially designed for the automatic control of 230VAC powered, 1 or 2 motor driven accesses. It is fitted with an innovative self-learning procedure allowing rapid

installation and four trimmers for fine adjustment of the main parameters; force, pause time, obstacle detection sensitivity and out of phase closing when two motors are used.

The following are available:

- simplified programming, thanks to which the unit automatically performs a learning operation to acquire running time and determine slow-down setting at 85% of opening and closing runs;

- A professional programming in which the installer can determine the instant in which the gate starts to

slow-down, the enabling of the pedestrian opening via radio, the safety device trigger mode.

2. MAIN FEATURES

•

Management and control of 230VAC (max 400W) powered, 1 or 2 motor-driven automated accesses

•

Motors closing offset adjustable from 0 to 15 seconds using trimmers

•

Opening motors delay settable at 0 or 3 seconds

•

Double limit switch input open close

•

Motor force (speed) adjustable from 50-100%.using a trimmer.

•

Customisable partial opening (for pedestrian transit)

•

0 to 60” stand-by time adjustment via trimmer.

•

0.1 to 3.0” obstacle detection triggering time adjustment via trimmer.

•

Initial settings using dip-switches

•

Signalling LEDs (8)

•

Expansion for electric lock 12V 15W max (optional board ELU, with optional relay)

•

Expansion for courtesy light (optional board LCU)

•

Built-in 433MHz rolling-code receiver with 180 memorisable codes

•

Built-in flashing logic management

•

Flash microprocessor re-programmable on-board via serial interface.

•

Programming and control of the control unit using a portable terminal GTSYSTEM (optional)

•

Built to European reference Directive Standards (R&TTE 99/05/CE)

DECLARATION OF CONFORMITY

Prastel S.p.A. declares that UNIK2E230 IS IN ACCORDANCE with the 99/05/EC (R&TTE) direcitve The complete declaration of conformity is available in Prastel or to the internet address www.prastel.it

3. TECHNICAL SPECIFICATIONS

Transformer power supply: primary230 / secondary 18V 20VA / secondary12V 20VA Control unit power: 230VAC Motor output: 2 x 400W Max current peak of motor: Max 8 Ampere Accessories power: 24 VDC - 500 mA protected by fuse (see info page 13) Environmental operating temperature : -20°C / + 55 °C Programming parameters: memorised in EEPROM Functions handler: microprocessor with watch-dog BOX IP rating: IP54

UNIK2E230 V2

INITIAL FACTORY SETTINGS

ENGLISH

ISUNIK2E230v2_GB_10_12.doc

4. CONNECTION AND SET UP OF THE CONTROL UNIT

a) Before installing the UNIK2E230 control unit, read the “General safety warnings and

notes” (page 15).

b) Mount a differential thermo-magnetic circuit breaker 6A (IC=30mA) on the mains supply

as specified in the current reference standards (IC = differential current).

Fix the box using the special fixing holes.

d) * Place the supplied cable-ways and insert the cables keeping the power and supply

cables separate from each other.

e) Connect the motors to the terminal blocks “MOT1” e “MOT2”; if only one motor is used

connect it to the terminal blocks “MOT1”.

f) Connect the external accessories making sure that the total of the average absorption

of all the connected accessories is less than the maximum current available (see info page 13).

g) ATTENTION: Connect the limit switches if present, otherwise do not bridge inputs

FC1, FC2, FO1, and FO2 in the terminal board.

h) ATTENTION: To avoid noisy or irregular operating when the control panel is used

with hydraulic operators, the following is recommended:

• set the Force to 100% (“FOR” trimmer completely clockwise).

• do not use the slow-down (carry out the professional learning procedure).

• do not use the obstacle detection (trimmer OBS to MAX),

i) During the learning with no electric limit switches present and with the obstacle

detection disabled (e.g. with hydraulic operators), or else with no mechanical STOP (strike plate) present, to define the manoeuvre times:

• Press pushbutton 1 of the remote control or pushbutton P1/SET to stop the gate in the desired position.

• Press pushbutton 2 of the remote control or pushbutton P2/SET to stop the gate in the desired position.

j) Check the correct connection and operation of all the accessories connected to the

terminal board.

NOTE:

When the control panel is mounted directly onto the operator with the special control

panel-holder, these two points are not relevant.

If there is no programming, the control unit will operate as follows:

• Step by step mode with automatic closing disabled

• No slow-down

• Closing safety present

• No opening safety

• Obstacle detection trigger time (OBS) 1 second

• 3 second opening and closing time of the motors

• Pushbutton 1 of transmitters enabled

• Safety test disabled

• Kick-back disabled

UNIK2E230 V2

30 31 32 33

ENGLISH

4.1 GENERAL DIAGRAM OF SETTINGS AND CONNECTIONS

ISUNIK2E230v2_GB_10_12.doc

+ 10 hidden pages