PRASTEL UNIK1E Technical Manual For The Installer

Technical Manual for the Installer

CONTROL UNITFORONEMOTOR

12VDC

UNIK1E

Attention!!Beforeinstalling, carefully read this manual.

N.B.

- Stateurop declines every responsib

the Country where the installation is made

The CE mark conforms to the European directive R&TTE 99/05CE

ility in case of not observance of the normative in force in

ENGLISH

SUMMARY

Title Description Page

• INTRODUCTION

1

• MAIN FEATURES

2

• TECHNICAL SPECIFICATIONS

3

• CONNECTING AND TURNING ON THE CONTROL UNIT

4

• EASY LEARNING PROCEDURE

5

• PROFESSIONAL LEARNING ROUTINE

6

3
3
3
4
5

7
7
8
9

10

• RADIOTRANSMITTERS PROGRAMMING AND ERASING

• SAFETIES AND OPERATING LOGIC

• CONTROL UNIT OPERATION

• Turning ON

• Automaticoperation

• Step-by-step operation

• Pedestrian opening

• Obstacle detection

• Flashing warning light

• Quick closing after photocell triggering

• Slowdown

• Emergency battery

• PROGRAMMING BY GTSYSTEM

8

9

9

9

9

9

9

10
10
10
10
10
10

11

• TROUBLESHOOTING

• SAFETY WARNINGS

11
12

2

ENGLISH

1. INTRODUCTION

UNIK1E is a universal self-learning control unit especially designed for the automatic control of 12VDC, 1 motor
driven accesses. Its innovative self-learning procedure makes for quick and easy installation and its three
trimmers permit fine adjustment of all main parameters, namely force, pause time and obstacle detection
sensitivity.
Are available :

- a quick self-learning routine thanks to which the unit automatically performs a learning operation to acquire
running times and determine slow down setting at ninety percent of opening and closing runs;

- a professional routine thanks to which the installer performs slow down triggering, remote pedestrian
opening, photocell-triggered instant reverse or reverse upon release.

2. MAIN FEATURES

• Management and control of 12/24VDC powered

• Quick and professional self-learning routines for acquisition of running and slow down times and of the

presence of safeties

• 50-100% force adjustment via trimmer

• Motor speed adjustment

• 0 to 60” stand-by time adjustment via trimmer

• 0.1 to 3.0” obstacle detection triggering time adjustment via trimmer

• Customisable partial opening (for pedestrian transit)

• 12V 15W electric lock expansion (optional ELU)

• Courtesy light expansion (optional LCU)

• Setting up for 12V 1.2Ah battery operation for optional emergency running

• Incorporated 433MHz rolling-code receiver

• 40 remote code storage capacity

• Reprogrammable on-board Flash microprocessor via serial interface

• Control unit programming via GTSYSTEM

• Built to European reference Directive Standards (R&TTE 99/05/CE)

3. TECHNICAL SPECIFICATIONS

Control Unit power: 230 VAC

Motor output: 12VDC 80Watt (24VDC with optional transformer TRT12-24V100VA)

Motor Current: Max 10 Ampere

Accessories power: 12 VDC - 150 mA

Operating temperature: -20°C / + 55 °C

Programmable parameters:in EE-PROM

Functions manager: microprocessor with watchdog

3

ENGLISH

4. CONNECTING AND TURNING ON THE CONTROL UNIT

• Before installing the UNIK1E control unit carefully read “General Safety Precautions”.

• Secure the box in place through the appropriate mounting holes.

• Make sure the power line is fitted with an appropriate disconnector / isolating switch as required by

prevailing reference Provisions and Standards.

• Fit on the fairleads provided and route the cable making sure to keep power lines separate from control
ones.

• Connect power and control lines according to the diagram and instructions given below.

• Make sure that all terminal board inputs are correctly connected and operative.

Obstacle

Force Trimmer

GTSYSTEM

P1/SET learning key

Sensitivity
Trimmer

P2/RADIO learning key

Radio channel

selector

Safeties test

selector

Radio Antenna

Photocell

Controls

ELU Electro-lock
expansion

Motor

10A battery fuse

Transformer
Secondary

Battery

4