Powerware 9125 Two-in-One
®
Extended Battery Module (EBM)
User’s Guide
For use with the Powerware 9125 Two-in-One
700–2000 VA UPS Models
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the
associated warning should be observed.
CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’s manual for
additional information, such as important operating and maintenance
instructions.
RJ-45 RECEPTACLE - For 230V models only: this receptacle provides network
interface connections. Do not plug telephone or telecommunications equipment
into this receptacle.
This symbol indicates that you should not discard the UPS or the UPS batteries
in the trash. This product contains sealed, lead-acid batteries and must be
disposed of properly. For more information, contact your local recycling/reuse or
hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic
equipment (WEEE) in the trash. For proper disposal, contact your local
recycling/reuse or hazardous waste center.
Powerware is a registered trademark of Eaton Electrical Inc.
ECopyright 2003–2006 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
Table of Contents
1 Introduction 1.........................................................
Safety Warnings 2......................................................................
2 Installation 15..........................................................
Inspecting the Equipment 15................................................................
EBM Installation 15......................................................................
Rack-Mount Installation 16..............................................................
Tower Installation 18..................................................................
3 EBM Maintenance 21....................................................
UPS and Battery Care 21..................................................................
Storing the UPS and Batteries 21............................................................
When to Replace Batteries 22...............................................................
How to Replace Extended Battery Modules 22...................................................
Recycling the Used Battery or UPS 24.........................................................
4 Service and Support 25..................................................
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
i
TABLE OF CONTENTS
ii
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
Chapter 1 Introduction
The Extended Battery Module (EBM) can be added to the 700–2000 VA
®
Powerware
9125 uninterruptible power system (UPS) to extend the
available battery time (see Table 1). Up to four EBMs can be installed
with the Powerware 9125 UPS.
Table 1. Battery Runtimes (in Minutes)
700–1000 VA Models
Load
200 VA/140W 37 271 546
400 VA/280W 19 142 278
700 VA/490W 9 72 156
850 VA/595W* 6 59 124
1000 VA/700W* 5 48 104
* Runtimes do not apply for 700 VA models.
Load
400 VA/280W 46 177 331 501 682
700 VA/490W 25 96 180 272 370
UPS Internal
Batteries
UPS Internal
Batteries
+1 EBM +2 EBMs +3 EBMs +4 EBMs
1250–2000 VA Models
+1 EBM +2 EBMs +3 EBMs +4 EBMs
850 VA/595W 21 76 142 214 292
1000 VA/700W 16 61 115 174 237
1250 VA/875W 11 46 87 131 179
1500 VA/1050W** 8 37 70 106 144
1800 VA/1260W*** 6 30 57 85 116
2000 VA/1400W*** 5 26 49 74 100
** Runtimes do not apply for 1250 VA models.
*** Runtimes do not apply for 1250 VA and 1500 VA models.
NOTE Battery times are approximate and vary depending on the load configuration and battery charge.
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
1
INTRODUCTION
Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
maintenance of the EBM. Please read all instructions before operating the equipment and
save this manual for future reference.
WARNING
This UPS contains its own energy source (batteries). The UPS output receptacles may carry
live voltage even when the UPS is not connected to an AC supply.
CAUTION
S Batteries can present a risk of electrical shock or burn from high short-circuit current.
Observe proper precautions. Servicing should be performed by qualified service
personnel knowledgeable of batteries and required precautions. Keep unauthorized
personnel away from batteries.
S Proper disposal of batteries is required. Refer to your local codes for disposal
requirements.
S Never dispose of batteries in a fire. Batteries may explode when exposed to flame.
2
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
Sikkerhedsanvisninger
Denne manual indeholder vigtige instruktioner, som skal følges under installation og
betjening af EBM-enheden. Læs venligst alle instruktioner inden betjening af udstyret og
gem denne manual mhp. fremtidige opslag.
Denne UPS indeholder sin egen energikilde (batterier). Udgangsstikkene kan endog være
strømførende, når UPS’en ikke er koblet til en vekselstrømsforsyning.
S Batterierne kan give risiko for elektrisk stød eller brandsår forårsaget af høj
kortslutningsstrøm. Overhold gældende forsigtighedsregler. Servicering skal udføres af
kvalificeret servicepersonale med kendskab til batterier og gældende forsigtighedsregler.
Hold uautoriseret personale væk fra batterierne.
S Korrekt bortskaffelse af batterier er påkrævet. Overhold gældende lokale regler for
bortskaffelsesprocedurer.
S Skaf dig aldrig af med batterierne ved at brænde dem. Batterierne kan eksplodere ved
åben ild.
INTRODUCTION
VIGTIGE SIKKERHEDSANVISNINGER
GEM DISSE ANVISNINGER
ADVARSEL!
ADVARSEL
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
3
INTRODUCTION
Belangrijke Veiligheidsinstructies
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
BEWAAR DEZE INSTRUCTIES
Deze handleiding bevat belangrijke instructies die u dient te volgen tijdens de installatie en
het gebruik van EBM. Lees alle instructies voordat u de apparatuur in bedrijf neemt en
bewaar deze handleiding als naslagwerk.
Deze UPS bevat een eigen energiebron (batterijen). De uitgangscontactdoos kan onder
spanning staan, zelfs wanneer de UPS niet is aangesloten op de netspanning.
S Batterijen leveren gevaar op voor elektrische schokken en kunnen brandwonden
veroorzaken door een grote kortsluitstroom. Neem de juiste voorzorgsmaatregelen in
acht. Het onderhoud moet worden uitgevoerd door bevoegde onderhoudsmonteurs die
verstand hebben van accu’s en op de hoogte zijn van de vereiste voorzorgsmaatregelen.
Houd onbevoegden uit de buurt van de accu’s.
S De batterijen moeten op de juiste wijze worden opgeruimd. Raadpleeg hiervoor uw
plaatselijke voorschriften.
S Nooit batterijen in het vuur gooien. De batterijen kunnen ontploffen.
WAARSCHUWING
OPGELET
4
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
Tarkeita Turvaohjeita
Tämä käyttöohje sisältää tärkeitä ohjeita, joita on noudatettava EBM-yksikön asennuksen ja
käytön yhteydessä. Lue kaikki ohjeet ennen laitteiston käyttöä ja säilytä ohje myöhempää
tarvetta varten.
Tässä UPS-virtalähteessä on oma energianlähde (akut). Lähtövastakkeissa voi olla jännite,
vaikka UPS-virtalähdettä ei ole kytketty verkkovirtaan.
S Akut voivat aiheuttaa sähköiskun tai palovammojen vaaran johtuen suuresta
S Akusto täytyy hävittää säädösten mukaisella tavalla. Noudata paikallisia määräyksiä.
S Älä koskaan heitä akkuja tuleen. Ne voivat räjähtää.
INTRODUCTION
TÄRKEITÄ TURVAOHJEITA - SUOMI
SÄILYTÄ NÄMÄ OHJEET
VAROITUS
VARO
oikosulkuvirrasta. Noudata kaikkia asianmukaisia varotoimia. Laitteen saa huoltaa vain
ammattitaitoinen huoltohenkilökunta, joka tuntee akut ja niihin liittyvät varotoimet. Älä
päästä valtuuttamatonta henkilöstöä lähelle akkuja.
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
5
INTRODUCTION
Consignes de Sécurité
Ce manuel contient des instructions importantes que vous êtes invité à suivre lors de toute
procédure d’installation et de fonctionnement de l’EBM. Veuillez consulter entièrement ces
instructions avant de faire fonctionner l’équipement et conserver ce manuel afin de pouvoir
vous y reporter ultérieurement.
Cette onduleur possède sa propre source d’alimentation (batteries). Il est possible que les
prises de sortie soient sous tension même lorsque l’onduleur n’est pas connectée à une
alimentation CA.
S Les batteries peuvent présenter un risque de choc électrique ou de brûlure provenant
S Une mise au rebut réglementaire des batteries est obligatoire. Consulter les règlements
S Ne jamais jeter les batteries au feu. L’exposition aux flammes risque de les faire
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
AVERTISSEMENT!
ATTENTION!
d’un courant de court-circuit haute intensité. Observez les précautions appropriées.
L’entretien doit être réalisé par du personnel qualifié connaissant bien les batteries et
les précautions nécessaires. N’autorisez aucun personnel non qualifié à manipuler les
batteries.
en vigueur dans votre localité.
exploser.
6
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
Sicherheitswarnungen
Dieses Handbuch enthält wichtige Hinweise, welche Sie bei der Installation und Wartung
des EBM beachten sollten. Bitte lesen Sie alle Anweisungen des Handbuches bevor sie mit
dem Gerät arbeiten. Bewaren Sie das Handbuch zum Nachlesen auf.
Dieses UPS (Unterbrechungsfreies Stromversorgungssystem - USV) enthält eine eigene
Energiequelle (Batterien). Die Ausgangssteckdosen können Spannung führen, auch wenn
das UPS (USV) nicht an eine Wechselstromquelle angeschlossen ist.
S Batterien können das Risiko eines elektrischen Schlags bergen oder durch hohen
Kurzschlussstrom in Brand geraten. Die richtigen Vorsichtsmaßnahmen beachten. Die
Wartung muss von qualifiziertem Wartungspersonal durchgeführt werden, das im
Umgang mit Batterien geübt ist und über gute Kenntnisse der erforderlichen
Vorsichtsmaßnahmen verfügt. Nicht autorisiertes Personal von Batterien fern halten.
S Die Batterien müssen ordnungsgemäß entsorgt werden. Hierbei sind die örtlichen
Bestimmungen zu beachten.
S Batterien niemals verbrennen, da sie explodieren können.
INTRODUCTION
WICHTIGE SICHERHEITSANWEISUNGEN
AUFBEWAREN
ACHTUNG
VORSICHT!
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
7
INTRODUCTION
Avvisi di Sicurezza
IMPORTANTI ISTRUZIONI DI SICUREZZA
CONSERVARE QUESTE ISTRUZIONI
Il presente manuale contiene importanti istruzioni da seguire durante l’installazione e il
funzionamento di EBM. Leggere integralmente le istruzioni prima di utilizzare
l’apparecchiatura e conservare il presente manuale per futuro riferimento.
AVVERTENZA
L’UPS contiene la propria fonte di energia (batterie). Le prese d’uscita possono essere sotto
tensione anche quando l’UPS non è collegato all’alimentazione elettrica CA.
ATTENZIONE
S Le batterie possono comportare un rischio di scossa elettrica o di ustione in seguito a
un’elevata corrente di corto circuito. Osservare le dovute precauzioni. L’assistenza deve
essere eseguita da personale qualificato esperto di batterie e delle necessarie
precauzioni. Tenere il personale non autorizzato lontano dalle batterie.
S Le batterie devono essere smaltite in modo corretto. Per i requisiti di smaltimento fare
riferimento alle disposizioni locali.
S Non gettare mai le batterie nel fuoco poichè potrebbero esplodere se esposte alle
fiamme.
8
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
Viktig Sikkerhetsinformasion
VIKTIGE SIKKERHETSINSTRUKSJONER
Denne håndboken inneholder viktige instruksjoner som du bør overholde ved montering og
bruk av EBM. Les alle instruksjoner før utstyret tas i bruk, og gjem håndboken til fremtidig
referanse.
UPS-enheten inneholder sin egen energikilde (batterier). Utgangsstikkene kan være
strømførende selv når UPS-enheten ikke er koblet til et strømuttak.
S Batterier kan utgjøre en fare for elektrisk støt eller brannsår pga. høy kortsluttingsstrøm.
Treff passende forholdsregler. Service bør utføres av kvalifisert servicepersonale med
kjennskap til batterier og nødvendige forholdsregler. Hold uautorisert personale borte fra
batteriene.
S Batterier må fjernes på korrekt måte. Se lokale forskrifter vedrørende krav om fjerning av
batterier.
S Kast aldri batterier i flammer, da de kan eksplodere, hvis de utsettes for åpen ild.
INTRODUCTION
GJEM DISSE INSTRUKSJONENE
FARLIG
FORSIKTIG
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
9
INTRODUCTION
Regulamentos de Segurança
INSTRUÇÕES DE SEGURANÇA IMPORTANTES
Este manual contém instruções importantes que devem ser seguidas durante a instalação e
operação da EBM (Produção de energia elétrica por indução magnética). Leia todas as
instruções antes de operar o equipamento e guarde este manual para consultá-lo
futuramente.
Este no-break possui sua própria fonte de energia (baterias). As tomadas de saída podem
estar energizadas mesmo que o no-break não esteja conectado a uma fonte de energia
elétrica.
S As baterias podem oferecer risco de choque elétrico ou queimadura, ocasionados por
alta tensão com possibilidade de curto-circuito. Tome as precauções adequadas. A
manutenção deve ser realizada por pessoal qualificado, com conhecimento sobre
baterias e ciente das precauções exigidas. Mantenha o pessoal não autorizado afastado
das baterias.
S Siga as instruções apropriadas ao desfazer-se das baterias. Consulte os códigos do local
para maiores informações sobre os regulamentos de descarte de produtos.
S Nunca jogue as baterias no fogo, porque há risco de explosão.
GUARDE ESTAS INSTRUÇÕES
ADVERTÊNCIA
PERIGO
10
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
Предупреждения по мерам безопасности
ВАЖНЫЕ УКАЗАНИЯ ПО МЕРАМ БЕЗОПАСНОСТИ
СОХРАНИТЕ ЭТИ УКАЗАНИЯ
В данном руководстве содержатся важные инструкции по установке и
обслуживанию внешнего батарейного модуля или устройства распределения
электропитания. Перед работой с оборудованием прочтите все инструкции.
Сохраните данное руководство для дальнейшего использования.
ПРЕДУПРЕЖДЕНИЕ
В данном ИБП установлены собственные источники энергии (батареи). На
выходных розетках может быть напряжение, даже если ИБП не подключен к
сети переменного тока.
ОСТОРОЖНО
S Высокое напряжение, вызванное коротким замыканием в батарее, может
привести к поражению электрическим током или ожогу. Соблюдайте
меры предосторожности. Техническое обслуживание должно
осуществляться квалифицированным персоналом по работе с
источниками питания, знакомым с мерами предосторожности. Не
допускайте к работе с батареями посторонних.
S Необходимо соблюдать правила утилизации аккумуляторов. Обратитесь к
местным нормативным актам за информацией о требованиях к
утилизации.
S Никогда не бросайте аккумуляторы в огонь. Аккумуляторы могут
взорваться под воздействием огня.
INTRODUCTION
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
11
INTRODUCTION
Advertencias de Seguridad
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
Este manual contiene instrucciones importantes que debe seguir durante la instalación y el
funcionamiento del EBM. Por favor, lea todas las instrucciones antes de poner en
funcionamiento el equipo y guarde este manual para referencia en el futuro.
Este SIE contiene su propia fuente de energía (baterías). Los receptáculos de salida pueden
transportar voltaje activo aun cuando el SIE no esté conectado con una fuente de CA.
S Las baterías pueden constituir un riesgo de descarga eléctrica o quemaduras por
corriente alta de corto circuito. Adopte las precauciones debidas. Personal calificado de
servicio que conozca de baterías y esté al tanto de las precauciones requeridas debe
darle servicio al equipo. Mantenga al personal no autorizado alejado de las baterías.
S Es necesario desechar las baterías de un modo adecuado. Consulte las normas locales
para conocer los requisitos pertinentes.
S Nunca deseche las baterías en el fuego. Las baterías pueden explotar si se las expone a
la llama.
GUARDE ESTAS INSTRUCCIONES
ADVERTENCIA
PRECAUCIÓN
12
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
Säkerhetsföreskrifter
Den här anvisningen innehåller viktiga instruktioner som du ska följa under installation och
användning av EBM. Läs alla instruktioner innan du använder utrustningen och spara den här
anvisningen för framtida referens.
Den här UPS-enheten innehåller sin egen energikälla (batterier). Uttagen kan vara
spänningsförande även då UPS-enheten inte är ansluten till spänningsnätet.
S Batterierna kan innebära en risk för elektrisk stöt eller brännskada från kortsluten
S Batterierna måste avyttras enligt anvisningarna i lokal lagstiftning.
S Använda batterier får aldrig brännas upp. De kan explodera.
INTRODUCTION
VIKTIGA SÄKERHETSFÖRESKRIFTER
SPARA DESSA FÖRESKRIFTER
VARNING
VIKTIGT
starkström. Iakttag lämpliga försiktighetsåtgärder. Service ska utföras av utbildad
servicepersonal med kunskap om batterierna och nödvändiga försiktighetsåtgärder. Håll
ej behörig personal borta från batterierna.
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
13
INTRODUCTION
14
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
Chapter 2 Installation
NOTE If you are installing the UPS and the Extended Battery Module together, follow the
installation instructions in the UPS user’s guide.
This section explains:
S Equipment inspection
S UPS and Extended Battery Module setup
S EBM installation
Inspecting the Equipment
If any equipment has been damaged during shipment, keep the shipping
cartons and packing materials for the carrier or place of purchase and file
a claim for shipping damage. If you discover damage after acceptance,
file a claim for concealed damage.
To file a claim for shipping damage or concealed damage: 1) File with
the carrier within 15 days of receipt of the equipment; 2) Send a copy of
the damage claim within 15 days to your service representative.
NOTE Check the battery recharge date on the shipping carton label. If the date has expired
and the batteries were never recharged, do not use the UPS. Contact your service
representative.
EBM Installation
The Powerware 9125 EBM is designed for flexible configurations and
can be installed in a rack or as a standalone cabinet.
If you are installing the EBM in a rack, continue to the following section
“Rack-Mount Installation;” otherwise, continue to “Tower Installation”
on page 18.
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
15
INSTALLATION
Rack-Mount Installation
The EBM can be installed in 19- or 23-inch racks and needs only 2U of
valuable rack space.
CAUTION
The EBM is heavy (29.5 kg/65 lb). A minimum of two people are required to lift the cabinet
into the rack.
NOTE Mounting rails are required for each UPS and EBM cabinet. If rails are not already
installed in your rack, contact your local distributor to order rail kits.
To install the EBM in a rack:
1. Place the EBM on a flat, stable surface with the front of the EBM
facing toward you.
2. Attach the supplied mounting handles to the mounting brackets and
secure with the supplied screws (see Figure 1).
3. Align the mounting brackets with the screw holes on the sides of
the EBM and secure with the supplied screws (see Figure 1).
16
4. If installing additional EBMs, repeat Steps 1 through 3 for each
cabinet.
Mounting
Bracket
Mounting
Handle
Figure 1. Installing the Mounting Handles and Brackets
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
INSTALLATION
NOTE The EBMs must be installed below the UPS as shown in Figure 2.
5. Slide the EBMs into the rack.
6. Secure the cabinets to the rack according to the rail kit instructions.
UPS
EBMs
Figure 2. Rack-Mount UPS with EBMs
7. Plug the EBM cable(s) into the battery connector(s) as shown in
Figure 3. Up to four EBMs may be connected to the UPS.
8. Follow the installation instructions in the Powerware 9125
Two-in-One UPS (700–2000 VA) User’s Guide for installing the UPS.
NOTE The batteries charge to 80% capacity in approximately 2 hours. However, it is
recommended that the batteries charge for 36 hours after installation or long-term storage.
NOTE If you installed power management software and EBMs, ensure maximum battery
runtime by using the ERM configurator tool on the Software Suite CD.
UPS
UPS Battery
Connector
EBM Cable
EBM
EBM
EBM Battery Connectors
Figure 3. Rack-Mount EBM Connections (120V Model Shown)
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
17
INSTALLATION
Tower Installation
The UPS and EBMs must be stabilized with joining brackets.
1. Carefully position the cabinets upright with the air vents at the top
(see Figure 4).
Air Vents
Figure 4. Tower UPS with EBMs
18
2. Remove the adjacent corner screws from the rear panels as shown
in Figure 5 to install the joining brackets. Discard the screws.
3. Align each joining bracket with the screw holes and secure with the
screws provided in the accessory kit.
4. If installing additional EBMs, repeat Steps 2 and 3 for each cabinet.
Joining Bracket
EBM UPS
Joining Bracket
Figure 5. Installing the Joining Brackets
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
INSTALLATION
5. Plug the EBM cable(s) into the battery connector(s) as shown in
Figure 6. Up to four EBMs may be connected to the UPS.
6. Follow the installation instructions in the Powerware 9125
Two-in-One UPS (700–2000 VA) User’s Guide for installing the UPS.
NOTE The batteries charge to 80% capacity in approximately 2 hours. However, it is
recommended that the batteries charge for 36 hours after installation or long-term storage.
NOTE If you installed power management software and EBMs, ensure maximum battery
runtime by using the ERM configurator tool on the Software Suite CD and connecting a
minimum load of 10% (15% recommended) to the UPS.
UPSEBMEBM
EBM Battery
Connectors
EBM Cables
Figure 6. Tower EBM Connections (120V Model Shown)
UPS Battery
Connector
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
19
INSTALLATION
20
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
Chapter 3 EBM Maintenance
This section explains how to:
S Care for the UPS and batteries
S Replace the Extended Battery Modules (EBMs)
S Recycle used batteries or UPS
UPS and Battery Care
For the best preventive maintenance, keep the area around the UPS
clean and dust-free. If the atmosphere is very dusty, clean the outside of
the system with a vacuum cleaner.
For full battery life, keep the UPS at an ambient temperature of
25°C (77°F).
NOTE The batteries in the UPS are rated for a 3–5 year service life. The length of service
life varies, depending on the frequency of usage and ambient temperature. Batteries used
beyond expected service life will often have severely reduced runtimes. Replace batteries at
least every 5 years to keep units running at peak efficiency.
Storing the UPS and Batteries
If you store the UPS for a long period, recharge the battery every
12 months by plugging the UPS into a power outlet. The batteries
charge to 80% capacity in approximately 2 hours. However, it is
recommended that the batteries charge for 36 hours after long-term
storage.
Check the battery recharge date on the shipping carton label. If the date
has expired and the batteries were never recharged, do not use the
UPS. Contact your service representative.
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
21
EBM MAINTENANCE
When to Replace Batteries
When the indicator flashes, the batteries may need replacing.
Conduct a self-test by pressing and holding the
seconds. After the test is complete, the
may take a few seconds to turn off). If the
flash, contact your service representative to order new batteries.
How to Replace Extended Battery Modules
NOTE DO NOT DISCONNECT the batteries while the UPS is in Battery mode.
With the hot-swappable battery feature, UPS batteries can be replaced
easily without turning the UPS off or disconnecting the load.
If you prefer to remove input power to change the batteries, see
“Turning the UPS Off” in the UPS user’s guide.
Consider all warnings, cautions, and notes before replacing batteries.
button for three
indicator should turn off (it
indicator continues to
22
WARNING
S Batteries can present a risk of electrical shock or burn from high short-circuit current. The
following precautions should be observed: 1) Remove watches, rings, or other metal
objects; 2) Use tools with insulated handles; 3) Do not lay tools or metal parts on top of
batteries.
S ELECTRIC ENERGY HAZARD. Do not attempt to alter any battery wiring or connectors.
Attempting to alter wiring can cause injury.
CAUTION
The EBM is heavy (29.5 kg/65 lb). A minimum of two people are required to lift the cabinet
into the rack.
To replace the EBMs:
1. Unplug the EBM cable from the UPS.
If additional EBMs are installed, unplug the EBM cable from the
battery connector on each EBM.
2. If the EBM is in a tower configuration, remove the joining brackets.
3. If the EBM is in a rack, install the supplied mounting handles and
brackets on the new EBM.
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
EBM MAINTENANCE
4. Replace the EBM. See “Recycling the Used Battery or UPS” on
page 24 for proper disposal.
5. Reinstall the joining brackets if removed in Step 2.
6. Plug the new EBM into the UPS as shown in Figure 7.
For additional EBMs, plug the EBM cable into the battery connector
on the adjacent EBM.
Joining Brackets
EBM Battery
Connectors
EBM Cables
UPS Battery
Connector
Figure 7. EBM Connections (120V Model Shown)
NOTE The battery connectors are designed to ensure proper connection with the correct
EBM model (use EBM model PW9125 24 EBM with 700–1000 VA UPSs and EBM model
PW9125 48 EBM with 1250–2000 VA UPSs).
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
23
EBM MAINTENANCE
Recycling the Used Battery or UPS
Contact your local recycling or hazardous waste center for information
on proper disposal of the used battery or UPS.
S Do not dispose of the battery or batteries in a fire. Batteries may explode. Proper
disposal of batteries is required. Refer to your local codes for disposal requirements.
S Do not open or mutilate the battery or batteries. Released electrolyte is harmful to the
skin and eyes. It may be toxic.
Do not discard the UPS or the UPS batteries in the trash. This product contains sealed,
lead-acid batteries and must be disposed of properly. For more information, contact your
local recycling/reuse or hazardous waste center.
Do not discard waste electrical or electronic equipment (WEEE) in the trash. For proper
disposal, contact your local recycling/reuse or hazardous waste center.
WARNING
CAUTION
CAUTION
24
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
Chapter 4 Service and Support
If you have any questions or problems with the UPS, call your Local
Distributor or the Help Desk at one of the following telephone numbers
and ask for a UPS technical representative.
United States:
Canada: 1-800-461-9166 ext 260
All other countries: Call your local service representative
Please have the following information ready when you call the Help
Desk:
1-800-356-5737 or 1-919-870-3149
S Model number
S Serial number
S Version number (if available)
S Date of failure or problem
S Symptoms of failure or problem
S Customer return address and contact information
If repair is required, you will be given a Returned Material Authorization
(RMA) Number. This number must appear on the outside of the package
and on the Bill Of Lading (if applicable). Use the original packaging or
request packaging from the Help Desk or distributor. Units damaged in
shipment as a result of improper packaging are not covered under
warranty. A replacement or repair unit will be shipped, freight prepaid for
all warrantied units.
NOTE For critical applications, immediate replacement may be available. Call the Help
Desk
for the dealer or distributor nearest you.
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
25
SERVICE AND SUPPORT
26
EATON Powerware®9125 Two-in-One EBM (700–2000 VA) User’s Guide S 05146489 Rev D www.powerware.com
Loading...