Series 9 Power Protection
True Online Design
True online systems such as the
Powerware 9120 are the only type
of UPSs that completely isolate connected equipment from all 9 of the
most common power problems:
Even when presented with the most
severe of these power problems, the
Powerware 9120 output remains
within a remarkable ±2% of nominal
voltage, meaning that your critical
system always receives clean power.
In addition, the Powerware 9120
transfers to battery with no break in
power, making it the perfect UPS for
equipment in environments plagued
by poor power.
Power Failures
UPS On
On Battery
On Bypass
Alarm
Starts Up/Shuts down the UPS
Scroll meters/
Select UPS settings
Scroll UPS settings/
Select UPS setting parameter
LCD
Power Sags
Power Surges
Undervoltage
Electrical
Line Noise
Overvoltage
Frequency
Variation
Switching
Transient
Harmonic
Distortion
Powerware 9120 Features
Front Panel Display
Informative user interface with LCD, four LED and audible alarms.
Loads Segments, Network Transient Protector and Remote
Emergency Power Off (REPO) Port
Load Segments are groups of receptacles that
can be independently controlled and extend
battery backup times for critical equipment.
To preserve battery power for more critical
equipment connected to Load Segment 1, shut
down Load Segment 2 supporting less critical
equipment.
Shut down and power up Load Segments in
user defined sequence.
The Network Transient Protector isolates your
modem, fax machine, and other electronic
equipment from “back door” power surges
The REPO port enables you to shut down the
UPS and connected equipment from a remote
location in an emergency.
1
2
3
4
1
2
3
4
Powerware 9120 1000 Shown
SOFTWARE SUITE
LanSafe III &
CheckUPS
Network Shutdown
for UPSs
LanSafe III &
CheckUPS
Network Shutdown
for UPSs
OnliNet
SNMP-Based
Network Shutdown
& Monitoring
OnliNet
SNMP-Based
Network Shutdown
& Monitoring
Foreseer
Facility & Data
Center Management
Foreseer
Facility & Data
Center Management
Foreseer
Facility & Data
Center Management
LanSafe III &
CheckUPS
Network Shutdown
for UPSs
PowerVision
UPS Performance
Analysis &
Monitoring
PowerVision
UPS Performance
Analysis &
Monitoring
PowerVision
UPS Performance
Analysis &
Monitoring
OnliNet
SNMP-Based
Network Shutdown
& Monitoring
Hot-Swappable Batteries
You can hot-swap batteries without powering down the critical load. This makes it possible to extend
the life of your UPS without returning the unit for service.
Extended Battery Modules (EBMs)
Increasing battery backup time is as simple as plugging in an extended battery module. Hot-swap
capability on all Powerware 9120 models allow you to expand run time or replace battery modules
while keeping your critical load up and running.
The lead-acid batteries typically used in a UPS are considered viable as long as they
can maintain backup time of at least half that of new batteries. The illustration below
shows that batteries that are constantly trickle charged (as are virtually all other UPS
batteries on the market today) reach the end of their useful life in less than half the
time of batteries charged using ABM. ABM uses a three-stage charging technique that
not only doubles battery service life, but also optimizes battery recharge time and
provides advanced notification of the end of useful battery life.
Advanced Battery Management (ABM) Technology Doubles Battery Service Life
Data based upon tests performed by an independent battery manufacturer
Battery Features and Run times
VA Standard Internal Battery 1 EBM 2 EBMs 3 EBMs 4 EBMs 5 EBMs
700 7/18 34/70 64/140 — — —
1000 7/18 36/80 66/155 — — —
1500 7/18 29/67 56/130 — — —
2000 12/34 49/107 93/195 140/310 192/403 240/504
3000 6/15 30/70 57/128 87/191 120/264 148/325
*Up to 2 EBMs can be connected to 700/1000/1500VA models and up to 5 EBMs can be connected to 2000/3000VA models. Run time chart provides typical information. Run times are approximate
and may vary with equipment, configuration, battery age, temperature, etc.
Battery Run Time Chart (in minutes full load/half load)*
Powerware 9120 - 1000VA shown with front cover
removed and battery shown sliding out.
SOFTWARE SUITE
LanSafe III &
CheckUPS
Network Shutdown
for UPSs
LanSafe III &
CheckUPS
Network Shutdown
for UPSs
OnliNet
SNMP-Based
Network Shutdown
& Monitoring
OnliNet
SNMP-Based
Network Shutdown
& Monitoring
Foreseer
Facility & Data
Center Management
Foreseer
Facility & Data
Center Management
Foreseer
Facility & Data
Center Management
LanSafe III &
CheckUPS
Network Shutdown
for UPSs
PowerVision
UPS Performance
Analysis &
Monitoring
PowerVision
UPS Performance
Analysis &
Monitoring
PowerVision
UPS Performance
Analysis &
Monitoring
OnliNet
SNMP-Based
Network Shutdown
& Monitoring
Communications
USB port (standard) allows UPS to communicate with Windows 98 and ME computers
RS232 Port (standard) for interface with power management software
SNMP/Web card (optional) adds direct control and monitoring capabilities in SNMP-based networks. Ability to
monitor UPS status and meters through web browser interface
Relay card (optional) adds integration to industrial environment and building management systems, shutdown
for IBM AS/400.
SOFTWARE SUITE
LanSafe III &
CheckUPS
Network Shutdown
for UPSs
LanSafe III &
CheckUPS
Network Shutdown
for UPSs
OnliNet
SNMP-Based
Network Shutdown
& Monitoring
OnliNet
SNMP-Based
Network Shutdown
& Monitoring
Foreseer
Facility & Data
Center Management
Foreseer
Facility & Data
Center Management
Foreseer
Facility & Data
Center Management
LanSafe III &
CheckUPS
Network Shutdown
for UPSs
PowerVision
UPS Performance
Analysis &
Monitoring
PowerVision
UPS Performance
Analysis &
Monitoring
PowerVision
UPS Performance
Analysis &
Monitoring
OnliNet
SNMP-Based
Network Shutdown
& Monitoring
Powerware Software Suite
The industry’s most comprehensive software bundle, the Powerware Software Suite CD, is free and
included with every Powerware 9120 UPS.
Software Wizard guides you through software selection and installation
In addition to multimedia demonstrations, product data sheets, and video clips, the
Software Suite contains the following power management software:
– LanSafe III and CheckUPS Network shutdown for UPSs
– OnliNet (Lite / Vista / Centro): SNMP-based network shutdown and monitoring for UPSs
– PowerVision (30-day trial version): UPS performance analysis and monitoring
– Foreseer (demonstration): Facility and data center management
Powerware Software Suite
Software and Connectivity Options
Rear Panels: 120V, 208V and 230V Models
SNMP/Web Card shown
PW9120 700, 120V
PW9120 1000, 120V PW9120 1500, 120V PW9120 2000, 120V PW9120 3000, 120V
PW9120 3000, 208V PW9120 700i/1000i, 230V PW9120 1500i, 230V PW9120 2000i, 230V PW9120 3000i, 230V
Electrical Input
Nominal Voltage 120 Vac and 230 Vac; See
Model Selection Guide for
user-selectable voltages
Input Voltage Range 120V: 80 –144 Vac
230V: 120/140/160-276 Vac
Input Power Factor >.95%
Operating Frequency 50/60Hz, Auto-sensing
Frequency Range 45-65Hz
Input Protection Fuse or circuit breaker
Electrical Output
On Utility Voltage Regulation ±2% of nominal
On Battery Voltage Regulation ±3% of nominal
Nominal Output Voltage Same as selected input voltage
Output Voltage Waveform Sine Wave
Output Voltage Distortion <3% THD
Output Protection Electronic overload sensing, and
circuit breaker protection
Efficiency Online Mode: >86%;
Hi-Efficiency Mode: >90%
Communications
User Interface LCD status screen
Audible Alarms UPS alarm conditions, including:
On-Battery, Low Battery, Overload,
UPS Fault
Network Transient Protector In and out jack for all models.
UL497A tested
REPO Port Meets NEC code 645-11 intent and
UL requirements
Communications One RS232 Serial Port; One
Communications Slot;
One USB Port
Communications Cable 6-foot communications cable
included
Power Management Software Powerware Software Suite CD,
free updates on
www.powerware.com
Technical Specifications
1
General
Topology True Online, double-conversion
Diagnostics Full System self-test on power up
UPS Bypass Automatic on Overload or
UPS failure < 4ms
Transfer Time to Battery 0 ms
Dimensions and Weights See Model Selection Guide
Overload Capacity 125% for 10 minutes before
transfer to bypass; 150% for 10
seconds before transfer to bypass
Battery
Internal/EBM Battery Type Sealed, lead-acid; maintenance free
Battery Runtime See Battery Runtime table
Battery Replacement Hot-swappable internal and
external batteries
Recharge Time <4 hours to 90% capacity
Start-On-Battery Allows start of UPS without
utility input
Environmental
Safety Certifications 120V: UL1778; cUL22.2 NO. 107.1;
230V: CE marked, EN 50091-1-1
and IEC 60950
EMI Compliance FCC Part 15, Class B (700-1500),
Class A (2000-3000) 230V, EN
50091-2 Class B (700-1500),
Class A (2000-3000)
Operating Temperature 0 to 400C (32 to 1040F)
Storage Temperature -15 to 500C (5 to 1220F)
Relative Humidity 0% to 95% non-condensing
Immunity IEEE C62.41,
IEC 61000-4 -2, -3, -4, -5
Network Transient Protector UL497A
Audible Noise at 1 meter 700-1000VA: <45dB; 1500VA
<50dB; 2000-3000 <52dB
Altitude 3000m (10,000 ft) without
deteriorating
1. Due to continuing product improvement programs, specifications are subject to change
without notice.
Model Selection Guide
Available Options
Order Number Description
IPK-0329 ConnectUPS-BD SNMP/WEB Card
1014018 AS/400 Relay Card
Powerware 9120 Family
1. Also user-selectable for 100, 110 and 127 Vac. 2. Automatic frequency selection. 3. 120V models have 6-ft attached line cord. 230V models have 6-ft detachable line cord.
4. Divided into 2 load segments (receptacle groups). 5. Also user-selectable for 220 and 240 Vac.
Model Power Out Input/OutPut Frequency Input Output Dimensions Weight
(VA/Watt) Voltage (Vac) (Hz)
2
Connection
3
Receptacles4(H x W x D) in/mm (LB/KG)
120 Vac Models
1
PW9120 700 700/490 120 50/60 5-15P (4) 5-15R 9.6 x6.2 x16.2/
243 x 158 x 412 29/13.2
PW9120 1000 1000/700 120 50/60 5-15P (4) 5-15R, 9.6 x 6.2 x 16.2/
(2) 5-20R 243 x 158 x 412 35.5/16.1
PW9120 1500 1500/1050 120 50/60 5-15P (4) 5-15R, 10.8 x 6.7 x 17.5/
(2) 5-20R 275 x 170 x 444 46.5/21.1
PW9120 2000 2000/1400 120 50/60 5-20P (6) 5-20R 14.2 x 8.6 x 18.6/
361 x 217 x 472 82/37.2
PW9120 3000 3000/2100 120 50/60 L5-30P (4) 5-15R, 14.2 x 8.6 x 18.6/
(2) 5-20R, 361 x 271 x x 472 89/40.5
(1) L5-30R
PW9120 3000h 3000/2100 120 50/60 Hardwired Hardwired 361 x 271 x x 472 89/40.5
208 Vac Models
PW9120 3000 3000/2100 208 50/60 L6-20P (2) L6-15R, 14.2 x 8.6 x 18.6/
(1) L6-20R, (1) L6-30R 361 x 217 x 472 89/40.5
230 Vac Models
5
PW9120 700i 700/490 230 50/60 IEC-C14 (4) IEC-C13 9.6 x 6.2 x 16.2/
243 x 158 x 412 28/12.6
PW9120 1000i 1000/700 230 50/60 IEC-C14 (4) IEC-C13 9.6 x 6.2 x 16.2/
243 x 158 x 412 34/15.3
PW9120 1500i 1500/1050 230 50/60 IEC-C14 (4) IEC-C13 10.8 x 6.7 x 17.5/
275 x 170 x 444 44/19.8
PW9120 2000i 2000/1400 230 50/60 IEC-C14 (4) IEC-C13, 14.2 x 8.6 x 18.6/
(1) IEC-C19 361 x 217 x 472 81.6/37
PW9120 3000i 3000/2100 230 50/60 IEC-C20 (4) IEC-C13, 14.2 x 8.6 x 18.6/
(1) IEC-C19 361 x 217 x 472 85/38.5
Optional Extended Battery Modules (EBMs)
PW9120 BATT 700 – – – Standard – 9.6 x 6.2 x 16.2/
Connector 243 x 158 x 412 31/14
PW9120 BATT 1000 – – – Standard – 9.6 x 6.2 x 16.2/
Connector 243 x 158 x 412 44/20
PW9120 BATT 1500 – – – Standard – 10.8 x 6.7 x 17.5/
Connector 275 x 170 x 444 57/26
PW9120 BATT 2000 – – – Standard – 14.2 x 8.6 x 18.6/
Connector 361 x 217 x 472 110/50
PW9120 BATT 3000 – – – Standard – 14.2 x 8.6 x 18.6/
Connector 361 x 217 x 472 110/50
9120FXA
Revision 6/02
Reprint 6/02
Invensys Powerware Division
8609 Six Forks Road
Raleigh, NC 27615 U.S.A.
Toll Free: 1.800.356.5794
or 919.872.3020
Fax: 1.800.753.9433
www.powerware.com
Europe
Finland: 358 94 52 661
France: 33 1 6012 7400
Germany: 49 7841 666 0
Italy: 39 02 6600661 2
UK: 44 (0) 1753 608700
Southeast Asia
Singapore: 65 6861 0377
China and North Asia
Hong Kong: 852 2745 6682
Japan
Shinagawa, Tokyo: 81 3 3447 4441
Australia and South Pacific
Sydney, Australia: 61 29878 5000
Canada
Toronto, Ontario: 416.798.0112
Brazil
Sao Paulo, Brazil: 55 11 3845
4369/ 55 11 3704 3632
Mexico
Col. Napoles, Mexico:
525.488.3333
Loading...