Loss of power 1. Rear of lawn mower 1. Raise cutting height.
housing or cutting blade
dragging in heavy grass.
2. Cutting too much grass. 2. Raise cutting height.
3. Dirty air fi lter. 3. Clean/replace air fi lter.
4. Buildup of grass, leaves, 4. Clean underside of mower
and trash under mower. housing.
5. Too much oil in engine. 5. Check oil level.
6. Walking speed too fast. 6. Cut at slower walking speed.
Poor cut – 1. Worn, bent or loose blade. 1. Replace blade. Tighten
uneven blade bolt.
2. Wheel heights uneven. 2. Set all wheels at same
height.
3. Buildup of grass, leaves 3. Clean underside of
and trash under mower. mower housing.
Excessive 1. Worn, bent or loose blade. 1. Replace blade. Tighten
vibration blade bolt.
2. Bent engine crankshaft. 2. Contact a qualifi ed service
center.
Starter rope 1. Engine fl ywheel brake is on 1. Depress control bar to
hard to pull when control bar is released. upper handle before
pulling starter rope.
2. Bent engine crankshaft. 2. Contact a qualifi ed service
center.
3. Blade adapter broken. 3. Replace blade adapter.
4. Blade dragging in grass. 4. Move lawn mower to cut
grass or to hard surface.
Grass catcher 1. Cutting height too low. 1. Raise cutting height.
not fi lling 2. Lift on blade worn off. 2. Replace blade.
(If so equipped) 3. Catcher not venting air. 3. Clean grass catcher.
Hard to push 1. Grass is too high or wheel 1. Raise cutting height.
height is too low.
2. Rear of lawn mower 2. Raise rear of lawn mower
housing or cutting blade housing one (1) setting
dragging in grass. higher.
3. Grass catcher too full. 3. Empty grass catcher.
4. Handle height position not 4. Adjust handle height to suit.
right for you.
PROBLEM CAUSE CORRECTION
TROUBLESHOOTING - See appropriate section in manual unless directed
to an authorized Service Center.
193732 Rev. 3 03.26.07 BY Printed in U.S.A.
DELUXE PUSH ROTARY
LAWN MOWER
WARNING: This lawn mower is equipped with an internal com bus tion engine and
should not be used on or near any un im proved forest-covered, brush-covered or
grass-cov ered land unless the engine’s exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a spark arrester is used, it
should be maintained in effective working order by the operator.
In the state of California the above is required by law (Section 4442 of the California
Public Resources Code). Other states may have similar laws. Federal laws apply
on federal lands. A spark arrester for the muffl er is available through your nearest
authorized service center.
2
Safety Rules ................. 2-3
Assembly......................4-7
Operation.................... 8-13
Storage.....................18-19
Troubleshooting........ 19-20
SAFETY RULES
TABLE OF CONTENTS
IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing ob-
jects. Failure to observe the following safety instructions could result in serious injury or death.
Look for this symbol to point out im por tant safety precautions. It means
CAU TION!!! BECOME ALERT!!!
YOUR SAFE TY IS INVOLVED.
WARNING: In order to prevent ac ci den tal
starting when setting up, trans port ing, ad just ing or making repairs, always dis con nect
spark plug wire and place wire where it can not
come in contact with plug.
WARNING: Engine exhaust, some of its
constituents, and certain vehicle com po nents contain or emit chem i cals known to
the State of Cal i for nia to cause can cer and
birth defects or oth er re pro duc tive harm.
WARNING: Battery posts, terminals and
related accessories contain lead and lead
compounds, chemicals known to the State
of Cal i for nia to cause can cer and birth
defects or oth er re pro duc tive harm. Wash
hands after handling.
CAUTION: Muffl er and
other engine parts become
extremely hot during
operation and remain hot
after engine has stopped.
To avoid severe burns on
contact, stay away from these areas.
I. GENERAL OPERATION
• Read, understand, and follow all
in struc tions on the machine and in the
manual(s) before starting. Be thor ough ly
familiar with the controls and the proper
use of the machine before starting.
• Do not put hands or feet near or under
rotating parts. Keep clear of the dis-
charge opening at all times.
• Only allow responsible individuals, who
are familiar with the in struc tions, to oper-
ate the machine.
• Clear the area of objects such as rocks,
toys, wire, bones, sticks, etc., which
could be picked up and thrown by blade.
• Be sure the area is clear of other people
before mowing. Stop ma chine if anyone
enters the area.
• Do not operate the mower when bare-
foot or wearing open sandals. Al ways
wear substantial foot wear.
• Do not pull mower backwards unless
absolutely nec es sary. Always look down
and behind before and while moving
backwards.
• Never direct discharged material toward
anyone. Avoid discharging material against
a wall or obstruction. Material may richochet back toward the operator. Stop the
blade when crossing gravel surfaces.
• Do not operate the mower without
proper guards, plates, grass catcher or
oth er safety protective devices in place.
• See manufacturer’s instructions for
proper operation and installation of
accessories. Only use accessories approved by the manufacturer.
• Stop the blade(s) when crossing grav el
drives, walks, or roads.
• Stop the engine (motor) whenever you
leave the equip ment, before clean ing the
mower or unclogging the chute.
• Shut the engine (motor) off and wait until
the blade comes to complete stop before
removing grass catcher.
• Mow only in daylight / good artifi cial light.
• Do not operate the machine while under
the infl uence of alcohol or drugs.
• Never operate machine in wet grass.
Always be sure of your footing: keep a
fi rm hold on the handle; walk, never run.
• Disengage the self-propelled mech a nism or drive clutch on mowers so
equipped before starting the engine.
• If the equipment should start to vi brate
abnormally, stop the engine (motor) and
check immediately for the cause. Vibration is generally a warning of trouble.
• Always wear safety goggles or safe ty glasses with side shields when op er at ing mower.
II. SLOPE OPERATION
Slopes are a major factor related to slip &
fall accidents which can result in severe injury. All slopes require extra caution. If you
feel uneasy on a slope, do not mow it.
DO:
• Mow across the face of slopes: nev er
up and down. Exercise extreme caution
when changing direction on slopes.
Maintenance.............14-16
Service and
Adjustments.............. 16-17
19
CYLINDER
• Remove spark plug.
• Pour one ounce (29 ml) of oil through
spark plug hole into cylinder.
• Pull starter handle slowly to dis trib ute oil.
• Replace with new spark plug.
BATTERY (IF EQUIPPED)
Disconnect the battery from the engine
connector and charge battery 48 hours.
OTHER
• Do not store gasoline from one sea son
to another.
• Replace your gasoline can if your can
starts to rust. Rust and/or dirt in your
gasoline will cause problems.
• If possible, store your unit indoors and
cover it to protect it from dust and dirt.
• Cover your unit with a suitable pro tec tive
cover that does not retain mois ture. Do
not use plastic. Plas tic cannot breathe,
which allows con den sa tion to form and
will cause your unit to rust.
IMPORTANT: Never cover mower while
engine and exhaust areas are still warm.
CAUTION: Never store the lawn mow er
with gaso line in the tank in side a build ing
where fumes may reach an open fl ame
or spark. Allow the engine to cool before
storing in any en clo sure.
ENGINE
FUEL SYS TEM
IMPORTANT: It is important to prevent gum
deposits from forming in essential fuel system
parts such as carburetor, fuel fi lter, fuel hose,
or tank during storage. Alcohol blended fuels
(called gasohol or using ethanol or methanol)
can attract moisture which leads to separation and formation of acids during storage.
Acidic gas can damage the fuel system of
an engine while in storage.
• Drain the fuel tank.
• Start the engine and let it run until the
fuel lines and car bu re tor are empty.
• Never use engine or carburetor cleaner
prod ucts in the fuel tank or permanent
damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in min i miz ing the formation of fuel
gum deposits during stor age. Add stabilizer
to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer
container. Run engine at least 10 min utes
after adding stabilizer to allow the stabilizer
to reach the car bu re tor. Do not drain the gas
tank and car bu re tor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace
with clean oil. (See “ENGINE” in the Maintenance section of this manual).
Does not start 1. Dirty air fi lter. 1. Clean/replace air fi lter.
2. Out of fuel. 2. Fill fuel tank.
3. Stale fuel. 3. Drain fuel tank and refi ll tank
with fresh, clean gasoline.
4. Water in fuel. 4. Drain fuel tank and refi ll tank
with fresh, clean gasoline.
5. Spark plug wire is 5. Connect wire to plug.
disconnected.
6. Bad spark plug. 6. Replace spark plug.
7. Loose blade or broken 7. Tighten blade bolt or
blade adapter. replace blade adapter.
8. Control bar in released 8. Depress control bar to
position. handle.
9. Control bar defective. 9. Replace control bar.
10. Fuel valve lever (if so 10. Turn fuel valve lever
equipped) in OFF position. to the ON position.
11. Weak battery (if equipped). 11. Charge battery.
12. Disconnected battery 12.Connect battery to engine.
connector (if equipped).
PROBLEM CAUSE CORRECTION
TROUBLESHOOTING - See appropriate section in manual unless directed
to an authorized Service Center.
18
STORAGE
Immediately prepare your lawn mower for
storage at the end of the season or if the
unit will not be used for 30 days or more.
CAUTION: Never store the lawn mower
with gaso line in the tank inside a build ing
where fumes may reach an open fl ame
or spark. Allow the engine to cool before
storing in any enclosure.
LAWN MOWER
When lawn mower is to be stored for a period of time, clean it thor oughly, remove all
dirt, grease, leaves, etc. Store in a clean,
dry area.
• Clean entire lawn mower (See “CLEAN ING” in the Maintenance section of this
manual).
• Lubricate as shown in the Main te nance
section of this manual.
• Be sure that all nuts, bolts, screws, and
pins are securely fas tened. Inspect
moving parts for damage, breakage and
wear. Replace if necessary.
• Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
HANDLE
Your handle may be folded for storage as
shown.
• Squeeze the bottom ends of lower
handle towards each other until handle
clears the handle brackets and swing
handles forward over mower.
• Loosen upper handle mounting hard ware enough to allow upper handle to be
folded back.
IMPORTANT: When folding handles for
storage or transportation, be sure to fold
handles as shown or you may damage the
control cables.
Lower handle
SQUEEZE
TO FOLD
2 POSITION / “ADJUSTABLE” HAN DLES
When setting you handles up from the
storage position, the lower handle will
au to mat i cal ly lock into mow ing position.
3 POSITION HANDLES
When setting up your handle from the storage position, the lower han dle will require
manually locking into the mowing position.
FOLD
FORWARD
FOR
STORAGE
MOWING
POSITION
Lower handle
Operator
presence
control bar
Upper
handle
Handle
knob
3 POSITION “EZ”
3 POSITION “QUICK”
Handle
ad just ment
brack et
Knob
Bolt
Handle pin
Handle
ad just ment
bracket
SQUEEZE
3
CONGRATULATIONS on your purchase of a new Lawn Mower. It has been designed, en gi neered and manu fac tured to give you the best pos sible de penda bil ity and per form ance.
Should you experience any prob lems you can not easily remedy, please contact your
nearest authorized service center. They have com pe tent, well trained tech ni cians and
the proper tools to service or repair this unit.
• Read the SAFETY RULES and this Operator's Manual in its entirety before you attempt to assemble or operate your new lawn mower to insure proper operation and to
prevent injury to yourself and others. Save this manual for future reference.
• Your new lawn mower has been assembled at the factory with the exception of those
parts left unassembled for shipping purposes. To ensure safe and proper operation
of your lawn mower, all parts and hardware you assemble must be tightened securely.
Use the correct tools as necessary to ensure proper tightness.
• All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have
been placed in the parts bag.
• Remove obstacles (rocks, tree limbs, etc.)
• Watch for holes, ruts, or bumps. Tall
grass can hide obstacles.
DO NOT:
• Do not trim near drop-offs, ditches or
embankments. The operator could lose
footing or balance.
• Do not trim excessively steep slopes.
• Do not mow on wet grass. Reduced footing could cause slipping.
III. CHILDREN
Tragic accidents can occur if the op er a tor is
not alert to the presence of children. Children
are often attracted to the ma chine and the
mowing activity.
Never
assume that children
will remain where you last saw them.
• Keep children out of the trimming area
and under the watchful care of an oth er
re spon si ble adult.
• Be alert and turn machine off if chil dren
enter the area.
• Before and while walking back wards,
look behind and
down
for small chil dren.
• Never allow children to operate the mower.
• Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.
IV. SAFE HANDLING OF GASOLINE
Use extreme care in handling gasoline.
Gasoline is extremely fl ammable and the
vapors are explosive.
• Extinguish all cigarettes, cigars, pipes
and other sources of ignition.
• Use only an approved container.
• Never remove gas cap or add fuel with
the engine running. Allow engine to cool
before refueling.
• Never refuel the machine indoors.
• Never store the machine or fuel container where there is an open fl ame, spark
or pilot light such as a water heater or on
other appliances.
• Never fi ll containers inside a vehicle, on
a truck or trailer bed with a plastic liner.
Always place containers on the ground
away from your vehicle before fi lling.
• Remove gas-powered equipment from the
truck or trailer and refuel it on the ground. If
this is not possible, then refuel such equipment with a portable container, rather than
from a gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim
of the fuel tank or container opening at
all times until fueling is complete. Do not
use a nozzle lock-open device.
• If fuel is spilled on clothing, change
clothing immediately.
• Never overfi ll fuel tank. Replace gas cap
and tighten securely.
V. GENERAL SERVICE
• Never run machine inside a closed area.
• Never make adjustments or repairs with
the engine (motor) running. Dis con nect the
spark plug wire, and keep the wire away
from the plug to prevent ac ci den tal starting.
• Keep nuts and bolts, especially blade
attachment bolts, tight and keep equipment in good condition.
• Never tamper with safety devices. Check
their proper operation reg u lar ly.
• Keep machine free of grass, leaves, or other
debris build-up. Clean oil or fuel spillage.
Allow machine to cool before storing.
• Stop and inspect the equipment if you
strike an object. Repair, if nec es sary,
before restarting.
• Never attempt to make wheel height
adjustments while the engine is running.
• Grass catcher components are sub ject to
wear, dam age, and de te ri o ra tion, which
could expose moving parts or allow objects
to be thrown. Frequently check com po nents
and replace with man u fac tur er’s recommended parts, when necessary.
• Mower blades are sharp and can cut.
Wrap the blade(s) or wear gloves, and
use extra caution when ser vic ing them.
• Do not change the engine governor setting or overspeed the engine.
• Maintain or replace safety and instruction labels, as necessary.
4
CAUTION: Do not operate this lawn
mower without the discharge guard or an
entire approved grass catcher in place.
These guards are for your protection and
are required by the American National
Standards Institute and Consumer Products Safety Com mis sion.
CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with plug.
HOW TO SET UP YOUR LAWN
MOW ER
UNFOLD HANDLE
IMPORTANT: Unfold handle carefully so
as not to pinch or damage con trol cables.
2 POSITION / “ADJUSTABLE” HANDLES
• Raise handles until lower handle section
locks into place in operating position.
ASSEMBLY
TO REMOVE MOWER FROM CARTON
• Remove all loose parts from carton.
• Remove lawn mower hous ing with care. Avoid touch ing blade under hous ing. Always
wear gloves or other protection when working under or lifting mower.
THINGS TO KNOW BE FORE YOU ASSEMBLE OR OPERATE YOUR LAWN
MOW ER
Do I have a side or rear discharge lawn
mower?
Look for the grass discharge opening on
your mower. If the opening is on the right
side of the mower housing, it is a side
discharge mower. If the opening is at the
back of the mower housing, it is a rear discharge mower. Only rear discharge lawn
mowers have a grass catcher in clud ed with
the mower. Approved grass catchers for
side discharge mow ers may be purchased
from your nearest au tho rized dealer.
Do I have a mulching lawn mower?
Look for the grass discharge opening on
your mower. Raise the discharge guard
(rear door on rear discharge mowers). If
the opening is closed off by a plate, then
your lawn mower is mulcher ready. To
convert to a discharging mower, see the
Operation section of this manual.
LEFT
HAND
SIDE
RIGHT
HAND
SIDE
FRONT
What is the right and left side of the
lawn mower?
When right hand (RH) or left hand (LH) is
mentioned in this man ual, it means when
you are in the operating po si tion (stand ing
be hind the handle).
What kind of engine is on my lawn
mower?
When learning how to operate your new
lawn mower, you will need to know what
kind of engine powers the mower. A decal
on the engine will indicate the man u fac tur er and type or brand name of the
engine.
BRIGGS & STRATTON ENGINES
BACK or REAR
(Op er at ing Position)
®
HONDA
ENGINES
TECUMSEH
EN GINES
17
3 POSITION “EZ”
The handle on your lawn mower has three
(3) height positions - adjust to height that
suits you.
• Remove knob and carriage bolt on one
side of the lower handle.
• While holding handle assembly, remove
knob and car riage bolt from opposite
side, align hole in handle with desired
hole in handle bracket and reassemble
bolt and knob and tighten securely.
• Align opposite side of handle with same
positioning hole and secure with bolt and
knob.
Handle
adjustment
bracket
Knob
Bolt
High
Med.
Low
3 POSITION “QUICK”
The handle on your lawn mower has three
(3) height positions - adjust to height that
suits you.
• Squeeze the bottom ends of lower
handle towards each other until the pin
in handle can be inserted into one of the
three height adjustment holes.
High
Handle
adjustment
bracket
Handle pin
Medium
Low
SQUEEZE
REAR DEFLECTOR (IF EQUIPPED)
The rear defl ector, attached between the
rear wheels of your mower, is provided to
minimize the pos si bil i ty that objects will
be thrown out of the rear of the mower
into the operator mowing position. If the
defl ector becomes dam aged, it should be
replaced.
ENGINE
CARBURETOR
The carburetor has been preset at the factory and ad just ment should not be necessary. However, minor ad just ment may be
required to compensate for differences in
fuel, temperature, altitude or load.
• The air fi lter must be assembled to the
car bu re tor when running engine.
• Best carburetor adjustment is obtained
when fuel tank is 1/4 full.
• In order for the engine to run, the operator presence control bar must be held
in the operating position. There fore,
and assistant will be required to hold
the control bar in the operating position
when making fi nal adjustment to the
car bu re tor.
See the ADJUSTMENT section of your
engine manual for further instructions.
ENGINE SPEED
The engine speed has been factory set.
Do not attempt to increase engine speed
as it may result in personal injury. If you
believe the engine is running too fast
or too slow, take your lawn mower to an
authorized engine service center for repair
and adjustment.
THROTTLE CONTROL
If it becomes necessary to adjust or replace the throttle control, see the ADJUSTMENT section of your engine man ual.
16
SERVICE AND ADJUSTMENTS
CAUTION: Before performing any service or adjustments:
• Release operator presence control bar.
• Make sure the blade and all moving parts have com plete ly stopped.
• Disconnect spark plug wire from spark plug and place wire where it can not come in
contact with plug.
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See “TO ADJUST CUTTING HEIGHT” in
the Operation sec tion of this manual.
TO ADJUST HANDLE
2 POSITION HANDLES
The handle can be mounted in a high or
low po si tion. The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle.
• Remove upper handle and all parts attached to lower handle.
• Remove hairpin cotters from lower
handle bracket mount ing pin.
• Squeeze lower handle in to remove it
from mounting pins.
• Turn lower handle over to raise or lower
handle.
• Squeeze lower handle in and position
holes onto mount ing pins on handle
bracket.
• Reassemble hairpin cotters onto mount ing pins.
• Reassemble upper handle and all parts
removed from lower handle.
TURN LOWER
HANDLE OVER
TO ADJUST HEIGHT
AIR FILTER
Your engine will not run properly and may
be damaged by using a dirty air fi lter.
Clean the element after every 25 hours of
operation or every season. Replace the air
fi lter every 100 hours of operation or every
season, whichever occurs fi rst. Service air
cleaner more often under dusty conditions.
See the maintenance section of your
engine manual.
MUFFLER
Inspect and replace corroded muffl er as it
could create a fi re hazard and/or damage.
SPARK PLUG
Replace spark plug at the beginning of
each mowing season or after every 100
hours of operation, whichever occurs fi rst.
Set spark plug gap according to engine
manual specifi cations.
CLEANING
IMPORTANT: For best performance, keep
mower housing free of grass build-up and
trash. Clean the underside of your mower
after each use.
• Clean the underside of your lawn mower
by scraping to remove buildup of grass
and trash.
• Clean engine often to keep trash from
accumulating. A clogged engine runs
hotter and shortens engine life.
• Keep fi nished surfaces and wheels free
of all gasoline, oil, etc.
We do not recommend using a garden
hose to clean your lawn mower unless the
electrical system, muffl er, air fi lter, and
carburetor are covered to keep water out.
Water in engine can shorten engine life.
GRASS CATCHER (IF SO EQUIPPED)
Grass catcher may be hosed with water
but must be dry when used.
CAUTION: Under nor mal usage, the
catch er material is subject to de te ri o ra tion
and wear and should therefore be checked
to ensure compliance with origi nal
manufacturer specifi cations.
Mowing
position
Mowing
position
HIGH POSITIONLOW POSITION
Handle
bracket
Hairpin
cotter
Mounting
pin
5
3 POSITION “QUICK” HANDLES
• Raise lower handle section to operating
position and squeeze the bottom ends
of lower handle towards each other until
the pin in handle can be inserted into
one of the three height adjustment holes.
3 POSITION “EZ” HANDLES
• Raise lower handle section to operating
position and align hole in handle with
one of three height positioning holes.
• Insert handle bolt through handle and
bracket and secure with knob.
• Repeat for opposite side of handle.
Flanged
locknut
Wheel
assembly
Wave
Washers
Axle
Handle
ad just ment
brack et
Knob
Bolt
Handle pin
Handle
ad just ment
bracket
SQUEEZE
ALL HANDLES
• Raise upper handle section into place on
lower han dle, remove protective padding
and tighten both handle knobs.
• Remove handle padding holding operator pres ence control bar to upper handle.
• Your lawn mower handle can be adjusted for your mowing comfort. Refer to
“ADJUST HANDLE” in the Service and
Adjustments section of this manual.
NOTE: For shipping purposes, the rear
wheels on your lawn mower may not be
adjusted to the same position as the front
wheels. Before operating mower adjust all
wheels to the same cutting height.
INSTALL REAR WHEELS
(HIGH WHEEL MOWERS ONLY)
Some high wheel models require wash ers
which will be pro vid ed in a parts bag. If provided, install washers on the axle fi rst as shown.
• Install one (1) rear wheel on the axle of
rear wheel adjuster.
• Install 3/8-16 locknut and tighten securely.
• Repeat procedure for other rear wheel.
MOWING
POSITION
Lower handle
LIFT
UP
Operator
presence
control bar
Upper
handle
LIFT
UP
Handle
knob
AS SEM BLE GRASS CATCHER
(REAR DISCHARGE MOWERS ONLY)
IMPORTANT: If your model lawn mower
is mulcher ready, the mulcher plate or plug
must be removed before using mower as
a bagger. To convert mower to bagging or
discharging, see the Operation section in
this manual.
Look at the different grass catcher illustrations that follow. Determine which type
of grass catcher you have and follow the
appropriate instructions.
6
CAUTION: Under normal usage, the
catcher material is subject to de te ri o ra tion
and wear and should, therefore, be
checked frequently for replacement. Any
replacement catcher should be checked to
ensure compliance with original man u fac tur er's spec i fi ca tions.
CAUTION: Do not run lawn mower
with out the discharge guard (rear door),
approved grass catcher, clipping de fl ec tor
or mulcher plate in place. Never attempt
to operate mower with the dis charge guard
(rear door) removed or propped open.
Hinge bracket
Formed tabs
Rear door
Grass
catcher
frame
HINGE BRACKET MOUNTED
DOOR PIVOT PIN MOUNTED
HANDLE BRACKET MOUNTED
DOOR SLOT MOUNTED
Handle bracket hooks Rear
door
Grass
catcher
handle
Catcher frame side hook
Rear door slots
Grass
catcher
han dle
Catcher frame hook
Pivot pins Grass
catcher
handle
Catcher frame hook
Rear
door
Frame
handle
Frame
opening
Vinyl
bindings
“FABRIC TOP” GRASS CATCHERS
TO ASSEMBLE AND ATTACH GRASS
CATCH ER
• Put grass catcher frame into grass bag
with rigid part of bag on the bottom.
• Slip vinyl bindings over frame.
NOTE: If vinyl bindings are too stiff, hold
them in warm water for a few minutes. If
bag gets wet, let it dry before using.
• Lift the rear door on the mower housing.
• For HINGE BRACKET mounted catcher,
place the grass catch er frame onto the
formed tabs on the rear door hinge
bracket.
• For HANDLE BRACKET mounted
catcher, place frame side hooks into
slots in handle brackets.
• For DOOR PIVOT PIN mounted catcher,
place the grass catcher frame hooks
onto the door pivot pins.
• For DOOR SLOT mounted catcher,
place the grass catcher frame hooks into
the slots of the rear door.
NOTE: The grass catcher is secured to the
lawn mower housing when the rear door is
lowered onto the grass catcher frame.
15
LAWN MOWER
Always observe safety rules when performing any main te nance.
TIRES
• Keep tires free of gasoline, oil, or insect
control chemi cals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
BLADE CARE
For best results, mower blade must be kept
sharp. Re place a bent or dam aged blade.
CAUTION: Use only a replacement
blade approved by the manufacturer of
your mower. Using a blade not approved
by the manufacturer of your mower is
hazardous, could damage your mower and
void your warranty.
TO REMOVE BLADE
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with plug.
2. Turn lawn mower on its side. Make sure
air fi lter and carburetor are up.
3. Use a wood block between blade and
mower hous ing to prevent blade from
turning when re mov ing blade bolt.
NOTE: Protect your hands with gloves
and/or wrap blade with heavy cloth.
4. Remove blade bolt by turning counter-
clockwise.
5. Remove blade and attaching hard-
ware (bolt, lock wash er and hardened
wash er).
NOTE: Remove the blade adapter and
check the key inside hub of blade adapter.
The key must be in good condition to work
properly. Replace adapter if damaged.
TO REPLACE BLADE
1. Position the blade adapter on the en-
gine crank shaft. Be sure key in adapter
and crankshaft keyway are aligned.
2. Position blade on the blade adapter
aligning the two (2) holes in the blade
with the raised lugs on the adapter.
3. Be sure the trailing edge of blade (op-
posite sharp edge) is up toward the
engine.
4. Install the blade bolt with the lock wash-
er and hardened washer into blade
adapter and crankshaft.
5. Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise.
• The recommended tightening torque is
35-40 ft. lbs.
IMPORTANT: Blade bolt is heat treated.
If bolt needs replacing, replace only with
approved bolt shown in the Repair Parts
section of this manual.
Blade
bolt
Crankshaft
keyway
Hardened
washer
Lockwasher
Blade adapter Key
Blade
Trailing edge
Crankshaft
TO SHARPEN BLADE
NOTE: We do not recommend sharp en ing
blade - but if you do, be sure the blade is
balanced. An un bal anced blade will cause
eventual damage to lawn mower or engine.
• The blade can be sharp ened with a fi le
or on a grinding wheel. Do not attempt to
sharpen while on the mower.
• To check blade balance, drive a nail into
a beam or wall. Leave about one inch of
the straight nail ex posed. Place center
hole of blade over the head of the nail.
If blade is balanced, it should remain in
a horizontal position. If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.
ENGINE
Read the maintenance section of your
engine manual.
LUBRICATION
Change the oil after the fi rst two hours of
operation and every 25 hours there af ter or
at least once a year if the lawn mower is
not used for 25 hours in one year. Refer to
engine manual.
TO CHANGE ENGINE OIL
(SEE ENGINE MANUAL)
• Be sure lawn mower is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
• For engines without dipstick, re move
bottom oil drain plug.
• For engines with oil fi ll cap/dipstick,
remove bottom drain plug or remove engine oil cap and turn mower on its side.
• After oil has drained completely, re place
oil drain plug and tighten se cure ly.
• Refi ll engine with oil. Pour slowly. Do
not overfi ll.
• Fill to top of slot inside of fi ller hole or
to “FULL” line on dipstick on models so
equipped. Keep oil at proper level.
14
➀ Spray lubricant
➁
See “ENGINE” in Maintenance section.
MAINTENANCE
Check for Loose Fasteners
Clean / Inspect Grass Catcher *
Check Tires
Check Drive Wheels ***
Clean Lawn Mower ****
Clean under Drive Cover ***
Check Drive Belt / Pulleys ***
Check / Sharpen / Replace Blade
Lubrication
Clean and Recharge Battery **
Check Engine Oil level
Change Engine Oil
Clean Air Filter
Inspect Muffler
Replace Spark Plug
Replace Air Filter Paper Cartridge
Empty fuel system or add Stabilizer
BEFORE
EACH
USE
AFTER
EACH
USE
EVERY
10
HOURS
EVERY
25 HOURS
OR SEASON
EVERY
100
HOURS
BEFORE
STORAGE
1 - Change more often if operating under a heavy load or in high outdoor temperatures.
2 - Service more often if operating in dirty or dusty conditions.
3 - Replace blades more often when mowing in sandy soil.
4 - Charge 48 hours at end of season.
5 - And after each 5 hours of use.
(if so equipped)
Electric-Start mowers
Power-Propelled mowers
Use a scraper
to clean under deck
*
**
***
****
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does not
cover items that have been subjected to operator abuse or negligence. To receive full
value from the war ranty, operator must maintain mower as instructed in this manual.
Some adjustments will need to be made
periodically to properly maintain your unit.
All adjustments in the Service and Adjustments section of this manual should be
checked at least once each season.
• Once a year, replace the spark plug,
clean or replace air fi lter element, and
check blade for wear. A new spark plug
and clean/new air fi lter element assures
proper air-fuel mixture and helps your
en gine run better and last longer.
• Follow the Maintenance Sched ule in this
manual.
BEFORE EACH USE
• Check engine oil level.
• Check for loose fasteners.
LUBRICATION
Keep unit well lubricated
(See “LUBRICATION CHART”).
IMPORTANT: Do not oil or grease plastic
wheel bearings. Viscous lu bri cants will
LUBRICATION CHART
attract dust and dirt that will short en the life
of the self-lu bri cat ing bearings. If you feel
they must be lu bri cated, use only a dry,
pow dered graphite type lubricant sparingly.
➀ Wheel
adjuster (on
each wheel)
➁ Engine oil
➀ Rear dis-
charge mower
rear door
hinge rod
➀ Handle bracket mounting pins
➀ Side dis-
charge mower
guard hinge rod
7
SPARK PLUG BOOT
On some models a spark plug boot is
packed loose in the parts bag. If your
model has the boot, install on spark plug
wire and reconnect spark plug wire to
spark plug.
TO PRE PARE BATTERY
(ELECTRIC START MODELS ONLY)
NOTE: Your battery must be charged
before you can start your lawn mower.
UNITS WITH HANDLE-MOUNTED KEY
SWITCH:
• Con nect battery charger con nec tor
(male) to harness con nec tor (fe male).
UNITS WITH DECK-MOUNTED
BATTERY:
• Disconnect engine connector (male)
from battery con nec tor (female).
• Connect battery charger connector
(male) to bat tery connector (fe male).
ALL UNITS:
• Plug battery charger into 110 volt A.C.
outlet.
• Leave battery charger connected for 24
hours before starting your engine for the
fi rst time.
UNITS WITH HANDLE-MOUNTED KEY
SWITCH:
• After charging, disconnect harness
connector (female) from bat tery charger
connector (male).
Connect your battery charger to charge
battery after each use.
IMPORTANT: The engine will not recharge
your battery.
Spark plug
Boot
DECK-MOUNTED BATTERY
Engine
connector
(male)
Harness
connector
(female)
Battery
charger
Charger
connector (male)
HANDLE-MOUNTED KEY SWITCH
UNITS WITH DECK-MOUNTED
BATTERY:
• After charging, connect engine con nec tor
(male) to bat tery connector (female).
Your engine has an integral alternator for
partial charging. Connect your battery
charger to charge battery as re quired.
IMPORTANT: The engine alternator will
not charge a discharged battery.
ALL UNITS:
At the end of the mowing season the
battery should be charged for 48 hours to
protect the battery during winter storage.
CAUTION: Always dis con nect the
en gine connector from the battery connector to prevent ac ci den tal start ing when
trans port ing or stor ing your lawn mower
after the season.
Engine connector (male)
Harness
connector
(female)
Battery charger
Charger
connector
(male)
Battery
box
8
Remote
throttle
control
FAS T
SLOW
CHOKE
(START)
OPERATION
The operation of any lawn mower can result in foreign objects thrown into
the eyes, which can result in severe eye damage. Always wear safety
glasses or eye shields while operating your lawn mower or performing any
ad just ments or repairs. We recommend standard safety glasses or a wide
vision safety mask worn over spectacles.
• Reinstall wheel components in the same
order as they were before removal.
Tighten securely.
• Make sure all wheels are at same height.
MODELS WITH “QUICK ADJUST”
WHEEL HEIGHT ADJUSTERS
NOTE: For shipping purposes, the rear
wheels on your lawn mower may not be
adjusted to the same position as the front
wheels. Before operating mower adjust all
wheels to the same cutting height.
• Raise wheels for low cut and lower
wheels for high cut.
• Adjust cutting height to suit your requirements. Me di um position is best for most
lawns.
• To change cutting height, squeeze adjuster
lever to ward wheel. Move wheel up or
down to suit your re quire ments. Be sure
all wheels are in the same setting.
NOTE: Adjuster is properly positioned when
plate tab inserts into hole in lever. Also, 9position adjusters (if so equipped) allow lever
to be positioned between the plate tabs.
Bolt
Flat washer
Wheel
3/8-16
Locknut
Spacer
LEVER BACKWARD
TO LOWER MOWER
LEVER FORWARD TO RAISE MOWER
Plate tab
Lever
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED CONTROL
MODELS WITH REMOTE THROTTLE
Engine speed is con trolled by the throttle
control located on the upper handle.
• Move lever forward to FAST engine
speed for start ing and better bagging.
• Move lever backward for SLOW engine
speed.
• Some models have engines equipped
with a choke feature. Move the lever all
the way forward to the CHOKE position
when starting a cold engine.
MODELS WITH FIXED SPEED ENGINES
Engine speed was set at the factory for
optimum per form ance. Engine speed is
not adjustable.
TO ADJUST CUTTING HEIGHT
Adjust cutting height to suit your re quire ments. Me di um position is best for most
lawns. Raise wheels for low cut and lower
wheels for high cut.
MODELS WITH MANUAL ADJUST
BOLT-ON WHEELS
• Remove wheel, bolt, and hardware and
reassemble in desired adjustment hole.
13
FOR MULCHING MOWERS ONLY
- MULCHING MOWING TIPS
IMPORTANT: For best performance, keep
mower housing free of built-up grass and
trash. See "CLEANING" in the Maintenance section of this manual.
• The special mulching blade will recut the
grass clip pings many times and reduce
them in size so that as they fall onto the
lawn they will disperse into the grass
and not be noticed. Also, the mulched
grass will bio de grade quickly to provide
nu tri ents for the lawn. Always mulch with
your highest engine (blade) speed as
this will provide the best recutting action
of the blades.
• Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
in ter feres with the mulch ing action. The
best time to mow your lawn is the early
afternoon. At this time the grass has
dried, yet the newly cut area will not be
exposed to direct sunlight.
• For best results, adjust the lawn mower
cutting height so that the lawn mower
cuts off only the top one-third of the
grass blades. If the lawn is overgrown it
will be necessary to raise the height of
cut to reduce pushing effort and to keep
from over load ing the engine and leaving
clumps of mulched grass. For ex tremely
heavy grass, reduce your width of cut by
overlapping previously cut path and mow
slowly.
MOWING TIPS
CAUTION: Do not use de-thatcher
blade attachments on your mower. Such
attachments are hazardous, will damage
your mower and could void your warranty.
• For most cutting conditions and bet ter
bagging per form ance, the engine speed
should be set in the FAST po si tion.
• Under certain conditions, such as when
mowing very tall grass, raise the mower
height on the fi rst cut to reduce pushing
effort, to avoid over heat ing the engine,
and to avoid leaving clumps of grass
clippings. Make the second cut to the
desired height.
• For extremely heavy cutting, reduce the
width of cut.
• For side discharge lawn mowers, cut in
a coun ter clock wise di rec tion, start ing at
the outside of the area to be cut, in order
to spread grass clip pings more evenly
and to put less load on the engine. To
keep clip pings off of walkways, fl ower
beds, etc., make the fi rst cuts in a clock wise direction.
• When using a rear discharge lawn
mower in moist, heavy grass, clumps
of cut grass may not enter the grass
catcher. Reduce ground speed (push ing
speed) and/or run the lawn mower over
the area a second time.
• If a trail of grass clipping is left on the
right side of a rear discharge lawn mower, mow in a clockwise direction with a
small overlap to collect the clippings on
the next pass.
• Pores in cloth grass catchers can become fi lled with dirt and dust with use
and the catcher will collect less grass.
To prevent this, regularly hose catcher
off with water and let dry before use.
• Certain types of grass and grass
con di tions may re quire that an area be
mulched a second time to com pletely
hide the clip pings. When doing a sec ond
cut, mow across (per pen dic u lar) to the
fi rst cut path.
• Change your cutting pattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting and
graining of the lawn.
MAX 1/3
12
BEFORE STARTING EN GINE
Read the engine manual packed with your
mower.
FILL ENGINE WITH OIL
Your lawn mower is shipped without oil in
the engine.
• Be sure mower is level and area around
oil fi ll is clean.
• Remove engine oil fi ller plug (oil fi ll cap/
dipstick on models so equipped).
• Slowly add oil. For type and grade of
oil to use, see “ENGINE” in the Maintenance section of this manual.
• Fill to the top of slot in fi ller hole (to
“FULL” line on dipstick on models so
equipped). Do not overfi ll.
• Replace plug (oil fi ll cap/dipstick on
models so equipped) and tighten.
• Check oil level before each use. Add oil
as needed.
• To change oil, see Maintenance section
of this manual.
FILL GASOLINE TANK
• Fill gasoline tank with fresh, clean, unleaded gaso line. DO NOT USE PREMIUM GASOLINE. BE CARE FUL NOT
TO OVERFILL TANK.
WARNING: Al co hol blended fuels (called
gaso hol or using ethanol or metha nol) can
at tract mois ture which leads to sepa ra tion
and for ma tion of acids during storage.
Acidic gas can damage the fuel system
of an en gine while in stor age. To avoid
engine prob lems, the fuel system should
be emptied before stor age of 30 days
or longer. Drain the fuel tank, start the
engine and let it run until fuel lines and
car bu re tor are empty. Use fresh fuel next
season. See Stor age In struc tions for
ad di tion al in for ma tion. Never use en gine or
car bu re tor clean er prod ucts in fuel tank or
per ma nent dam age may occur.
TO START ENGINE
CAUTION: The mow er blade rotates
whenever the engine is running.
• Move engine speed control to FAST
position (or to CHOKE/START position
on models equipped with choke feature).
• If your mower has a primer, to start a
cold engine, push primer as many times
as in struct ed in the engine manual
packed with your mower. Use a fi rm
push. This step is not usually nec es sary
when start ing an engine which has
already run for a few minutes.
• Hold operator presence control bar
down against han dle.
MODELS WITH RECOIL START ER
• Pull starter handle quickly. Do not allow
starter rope to snap back.
MODELS WITH ELECTRIC START ER
• Push the engine start button (or turn the
key on models so equipped).
IMPORTANT: Do not crank engine more
than fi ve continous seconds each time you
try to start. Wait 5 to 10 seconds between
each attempt.
ALL MODELS
• For engines equipped with choke, slowly
move engine speed control lever to
FAST after engine starts.
TO STOP ENGINE
• To STOP engine, release operator presence control bar.
NOTE: For engines with a primer, it may
be nec es sary to repeat priming steps
in cooler weather. In warmer weath er,
overpriming may cause fl ood ing and
en gine will not start. If you do fl ood
engine, wait a few minutes before
attempting to start and DO NOT repeat
priming steps.
Recoil
starter
handle
Operator
presence
control bar
9
FOR MULCHING MOWERS ONLY
Most mulching mowers are shipped ready
to be used as a mulcher.
“REAR DISCHARGE ONLY” MOWERS
Some models have a seperate mulcher
plug, other models have the mulcher plug
built into the rear door. To convert to bagging or discharging, the plate or plug (if
so equipped) must be removed from the
dis charge open ing of the lawn mower.
• Open rear door and remove mulcher
plate or plug (if so equipped). Store
mulcher plate or plug in a safe place.
• You can now install grass catcher or
optional clipping defl ector accessory.
• To return to mulching operation, install
mulcher plate or plug into discharge
opening of mower.
CAUTION: Do not run your lawn mower
without mulcher plate/plug in place or ap proved clipping defl ector or grass catch er
in place. Never attempt to op er ate the
lawn mower with the rear door removed or
propped open.
MULCHER "PLUG"
Slots
Mulcher
plate tabs
Mulcher plug
MULCHER "PLATE"
MULCHER PLUG BUILT INTO REAR DOOR
“SIDE DISCHARGE ONLY” MOWERS
MULCHER PLATE TYPE
To convert to bagging or discharging,
mulcher plate must be removed from underside of lawn mower.
• Remove the four (4) screws and lock nuts
securing the mulcher plate to the mower.
• Store mulcher plate and hardware in a
safe place.
• Mower can now be used for side
discharging or op tion al grass catcher
accessory can be attached.
• To return to mulching operation, simply
reinstall mulcher plate and tighten hardware securely.
Mulcher plate
Screw and
lock nut
10
“COMBI-CUT” MOWERS
Your lawn mower was shipped ready to be
used as a mulcher. To convert to bagging
or discharging:
REAR BAGGING
• Open rear door and remove mulcher
plate. Store mulcher plate in a safe
place.
• You can now install grass catcher.
• To convert to mulching or discharging
operation, install mulcher plug into rear
discharge opening of mower, mak ing
sure all tabs are seated properly.
Slots
Mulcher
plate tabs
MULCHER PLUG TYPE “B”
To convert to bagging or dis charg ing:
• Lift discharge guard and remove
mulcher plug.
• Mower can now be used for side dis charg ing or op tion al grass catcher can
be attached.
• To return to mulching operation, simply
reinstall mulcher plug as shown, making
sure tab is seated properly.
CAUTION: Do not run your lawn mower
without discharge guard, approved grass
catch er or mulcher plug in place.
MOWER IS
NOW READY
FOR MULCHING
OPERATION
SIDE DISCHARGING
• Mulcher plate must be installed into rear
discharge open ing of mower (see above
instructions).
• Open mulcher door and install dis charge
defl ector under door as shown.
• Mower is now ready for discharging
operation.
• To convert to mulching or bagging
operation, dis charge defl ector must be
removed and mulcher door must be
closed.
MULCHER PLUG TYPE “A”
To convert to mulching operation, mulcher
plug must be installed into discharge open ing of mower.
• Open discharge guard.
• Insert tab of mulch plug into housing
opening.
• Align hooks of mulch plug over hinge
rod of discharge guard. Push mulch plug
down until mulch plug is seat ed in housing opening.
CAUTION: Do not run your lawn mower
without discharge guard, ap proved grass
catcher or mulcher plug in place.
Hooks
Housing
opening
Mulcher plug
Hinge rod
Tab
Discharge
guard
Lift
discharge
guard
Install
mulcher plug
Tab
11
CAUTION: Do not run your lawn mower
without rear mulcher plate or plug in place
or approved grass catcher in place. Never
at tempt to op er ate the lawn mow er with
the rear door re moved or propped open.
GRASS CATCHER
(REAR BAGGING MODELS ONLY)
TO EMPTY GRASS CATCHER
• Simply open rear door and lift grass
catcher up and away from mower.
NOTE: Do not drag the bag when
emptying. It will cause unnecessary wear.
CAUTION: Under nor mal usage, the
catch er material is subject to de te ri o ra tion
and wear and should, therefore, be
checked frequently for replacement. Any
replacement catcher should be checked
to ensure compliance with original
man u fac tur er's spec i fi ca tions.
CAUTION: Do not run lawn mower
with out the rear door, ap proved grass
catcher or clip ping de fl ec tor in place.
Never at tempt to op er ate mower with the
rear door removed or propped open.
OPERATOR PRESENCE CONTROL
BAR
Your lawn mower is equipped with an op er a tor presence control bar which re quires
the operator to be po si tioned behind the
lawn mower handle in order to start and
operate the lawn mower.
CAUTION: Federal reg u la tions require
an en gine control to be in stalled on this
lawn mower in order to min i mize the
risk of blade contact injury. Do not un der
any cir cum stanc es attempt to de feat the
func tion of the operator con trol. The blade
turns when the engine is running.
Open mulcher door
Discharge defl ector
SIMPLE STEPS TO REMEMBER WHEN
CONVERTING YOUR “COMBI-CUT”
LAWN MOWER
FOR MULCHING -
• Rear mulcher plate installed and rear
door closed.
• Mulcher door closed.
FOR REAR BAGGING -
• Rear mulcher plate removed.
• Grass catcher installed.
• Mulcher door closed.
FOR SIDE DISCHARGING -
• Rear mulcher plate installed and rear
door closed.
• Discharge defl ector installed.
Loading...