Porter-Cable 352VS User Manual

BELT SANDER

Part No. 899748 - 04-21-03

ESPAÑOL: PÁGINA 15
FRANÇAISE : PAGE 31

Instruction

manual

The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. _______________________________________

IMPORTANT

Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

Copyright © 2003 Porter-Cable Corporation

MODEL352VS

2

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known (to the State of California) to

cause cancer, birth defects or other reproductive harm. Some example of these chemicals are:

●●

lead from lead-based paints

●●

crystalline silica from bricks and cement and other masonry products

●●

arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, always wear MSHA/NIOSH approved, properly fitting face mask or
respirator when using such tools.

SAFETY GUIDELINES - DEFINITIONS

indicates an imminently hazardous situation which, if not avoided, will result in

death or serious injury.

indicates a potentially hazardous situation which, if not avoided, could result in

death or serious injury.

indicates a potentially hazardous situation which, if not avoided,may result in

minor or moderate injury.

used without the safety alert symbol indicates potentially hazardous situation

which, if not avoided, may result in property damage.

This manual contains information that is important for you to know and understand. This information re­lates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize
this information, we use the symbols below. Please read the manual and pay attention to these
sections.

WORK AREA

1. Keep your work area clean and well lit. Cluttered benches and dark

areas invite accidents.

2. Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases, or dust. Power tools create

sparks which may ignite the dust or fumes.

3. Keep bystanders, children, and visitors away while operating a
power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove
the grounding prong or modify the plug in any way. Do not use any
adapter plugs. Check with a qualified electrician if you are in doubt as to
whether the outlet is properly grounded. If the tools should electrically

malfunction or break down, grounding provides a low resistance path to
carry electricity away from the user.

Read and understand all instructions. Failure to

follow all instructions listed below, may result in electric shock, fire
and/or serious personal injury.

SAVE THESE INSTRUCTIONS.

GENERAL SAFETY RULES

3

2

2. Avoid body contact with grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is grounded.

3. Don’t expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.

4. Do not abuse the cord. Never use the cord to carry the tools or pull
the plug from an outlet. Keep cord away from heat, oil, sharp edges or
moving parts. Replace damaged cords immediately. Damaged cords

increase the risk of electric shock.

5. When operating a power tool outside, use an outdoor extension
cord marked “W-A” or “W”. These cords are rated for outdoor use and

reduce the risk of electric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing, and use common sense when
operating a power tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while

operating power tools may result in serious personal injury.

2. Dress properly. Do not wear loose clothing or jewelry. Contain long
hair. Keep your hair, clothing, and gloves away from moving parts.

Loose clothes, jewelry, or long hair can be caught in moving parts.

3. Avoid accidental starting. Be sure switch is OFF before plugging in.

Carrying tools with your finger on the switch or plugging in tools that have
the switch ON invites accidents.

4. Remove adjusting keys or wrenches before turning the tool ON. A
wrench or a key that is left attached to a rotating part of the tool may result
in personal injury.

5. Do not overreach. Keep proper footing and balance at all times.

Proper footing and balance enable better control of the tool in unexpected
situations.

6. Use safety equipment. Always wear eye protection. Dust mask, non­skid safety shoes, hard hat, or hearing protection must be used for
appropriate conditions.

7. Use certified safety equipment. Eye protection equipment should
comply with ANSI Z87.1 standards, hearing equipment should comply with
ANSI S3.19 standards, and dust mask protection should comply with
MSHA/NIOSH certified respirator standards.

TOOLS USE AND CARE

1. Use clamps or other practical way to secure and support the
workpiece to a stable platform. Holding the work by hand or against your

body is unstable and may lead to loss of control.

2. Do not force tool. Use the correct tool for your application. The
correct tool will do the job better and safer at the rate for which it is
designed.

3. Do not use tool if switch does not turn it ON or OFF. A tool that
cannot be controlled with the switch is dangerous and must be repaired.

4. Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive

safety measures reduce the risk of starting the tool accidentally.

4

5. Store idle tools out of reach of children and other untrained
persons. Tools are dangerous in the hands of untrained users.

6. Maintain tools with care. Keep cutting tools sharp and clean.

Properly maintained tools, with sharp cutting edges are less likely to bind
and are easier to control.

7. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation. If
damaged, have the tool serviced before using. Many accidents are

caused by poorly maintained tools.

8. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may become

hazardous when used on another tool.

SERVICE

1. Tool service must be performed only by qualified repair personnel.

Service or maintenance performed by unqualified personnel may result in a
risk of injury.

2. When servicing a tool, use only identical replacement parts. Follow
instructions in the Maintenance Section of this manual. Use of

unauthorized parts or failure to follow Maintenance Instructions may create a
risk of electric shock or injury.

1. Hold the tool by the insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring or its own
cord. Contact with a “live” wire will make exposed metal parts of the tool

“live” and will shock the operator.

2. Use proper safety equipment. Wear safety goggles for eye protection,
wear hearing protection, and wear a protective mask to minimize breathing in
the fine dust created while sanding.

3. Sanding of lead-based paint is not recommended. Lead-based paint
should only be removed by a professional.

4. Always maintain a firm grip on the belt sander handles with both hands
to prevent loss of control.

5. Do not operate belt sander without all guards and covers securely in
place.

6. Some wood contains preservatives which can be toxic. Take extra
care to prevent inhalation and skin contact when working with these
materials. Request and follow any safety information available from your
material supplier.

This tool was designed for certain applications. DO NOT

modify and/or use it for any application other than for which
it was designed. If you have any questions relative to its application, DO NOT
use the tool until you have written Porter-Cable and we have advised you.

Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305

SPECIFIC SAFETY RULES AND SYMBOLS

5

SYMBOL DEFINITION

V ........................ volts

A ........................ amperes

Hz ........................ hertz

W ........................ watts

kW ........................ kilowatts

µF ........................ microfarads

l ........................ liters

kg ........................ kilograms

N/cm

2

........................ newtons per square centimeter

Pa ........................ pascals

h ........................ hours

min ........................ minutes

s ........................ seconds

........................ alternating current

3 ........................ three-phase alternating current

3

N ........................ three-phase alternating current with neutral

........................ direct current

n

0

........................ no load

........................ alternating or direct current

........................ Class II Construction

........................ splash-proof construction

........................ watertight construction

…/min ........................ revolutions or reciprocation per minute

Extreme care should be taken when removing paint. The
peelings, residue, and vapors of paint may contain lead,
which is poisonous. Exposure to even low levels of lead can
cause irreversible brain and nervous system damage. Young
and unborn children are particularly vulnerable.

Before beginning any paint removal process you should determine whether
the paint you are removing contains lead. This can be done by your local
health department or by a professional who uses a paint analyzer to check for
lead.

LEAD-BASED PAINT SHOULD ONLY BE REMOVED BY A PROFESSIONAL.

Persons removing paint should follow these guidelines:

1. KEEP THE WORK AREA WELL VENTILATED. Open the windows and
put an exhaust fan in one of them. Be sure the fan is moving air from inside
to outside.

2. REMOVE OR COVER any carpets, rugs, furniture, clothing, cooking
utensils, and air ducts.

3. PLACE DROP CLOTHS in the work area to catch any paint chips or
peelings. Wear protective clothing such as extra work shirts, overalls and hats.

ADDITIONAL SAFETY RULES FOR PAINT REMOVAL

6

4. WORK IN ONE ROOM AT A TIME. Furnishings should be removed or

placed in the center of the room and covered. Work areas should be sealed
off from the rest of the dwelling by sealing doorways with drop cloths.

5. CHILDREN, PREGNANT, OR POTENTIALLY PREGNANT women and
nursing mothers should not be present in the work area until the work is
done and all cleanup is complete.

6. WEAR A DUST RESPIRATOR or a dual filter (dust and fume) respirator
mask which has been approved by the Occupational Safety and Health
Administration (OSHA), the National Institute of Safety and Health (NIOSH),
or the United States Bureau of Mines. These masks and replaceable filters
are readily available at major hardware stores. Be sure the mask fits. Beards
and facial hair may keep the masks from sealing properly. Change filters
often. DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.

7. KEEP FOOD AND DRINK out of the work area. Wash hands, arms, and
face and rinse mouth before eating or drinking. Do not smoke or chew gum
or tobacco in the work area.

8. CLEAN UP ALL REMOVED PAINT and dust by wet mopping the floors.
Use a wet cloth to clean all walls, sills and any other surfaces where paint or
dust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high
phosphate detergent or trisodium (TSP) to wash and mop areas.

9. AT THE END OF EACH WORK SESSION, put the paint chips and debris
in a double plastic bag, close it with tape or twist ties and dispose properly.

10. REMOVE PROTECTIVE CLOTHING and work shoes in the work area to
avoid carrying dust into the rest of the dwelling. Wash work clothes
separately. Wipe shoes off with a wet rag, then wash that rag with the work
clothes. Wash hair and body thoroughly with soap and water.

REPLACEMENT PARTS

When servicing, use only identical replacement parts.

MOTOR

Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60
cycle A.C. current and voltage within plus or minus 5 percent of that shown
on the specification plate on the tool. Several models, however, are designed
for A.C. current only. Refer to the specification plate on your tool for proper
voltage and current rating.

Do not operate your tool on a current on which the voltage is
not within correct limits. Do not operate tools rated A.C. only
on D.C. current. To do so may seriously damage the tool.

EXTENSION CORD SELECTION

If an extension cord is used, make sure the conductor size is large enough to
prevent excessive voltage drop which will cause loss of power and possible
motor damage. A table of recommended extension cord sizes will be found
in this section. This table is based on limiting line voltage drop to 5 volts (10
volts for 230 volts) at 150% of rated amperes.

5

7

If an extension cord is to be used outdoors it must be marked with the suffix
W-A or W following the cord type designation. For example – SJTW-A to
indicate it is acceptable for outdoor use.

RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS

FOREWORD

The Porter-Cable Variable Speed Belt Sander (Model 352VS) is designed for
removing old paint and varnish, smoothing rough boards, and fine-surfacing
wood, metal, plastics, and other materials.

INSTALLING AND REMOVING THE ABRASIVE BELT

DISCONNECT TOOL FROM POWER SOURCE.

1. Place the sander on its left
side.

2. Pull the lever (A) Fig. 1 out
toward the front of the machine
to retract the idler pulley (B) and
release the tension on the
abrasive belt.

3. Remove the old belt.

4. Install the new belt with the
arrow (printed on the inside of
the belt) on the top and pointing
TOWARD the idler pulley.

Length of Cord in Feet

115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft.
230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft.

0-2 18 18 18 16 16 14 14 12 12
2-3 18 18 16 14 14 12 12 10 10
3-4 18 18 16 14 12 12 10 10 8
4-5 18 18 14 12 12 10 10 8 8
5-6 18 16 14 12 10 10 8 8 6
6-8 18 16 12 10 10 8 6 6 6

8-10 18 14 12 10 8 8 6 6 4
10-12 16 14 10 8 8 6 6 4 4
12-14 16 12 10 8 6 6 6 4 2
14-16 16 12 10 8 6 6 4 4 2
16-18 14 12 8 8 6 4 4 2 2
18-20 14 12 8 6 6 4 4 2 2

Nameplate Ampere Rating

Fig. 1

A

B

FUNCTIONAL DESCRIPTION

OPERATION

NOTE: Some sanding belts are bi-directional. These belts will not have

arrows printed on them. They can be installed to run in either direction.

5. Engage the front pulley by pushing the lever (A) Fig. 1 back to its original
position.

TO START AND STOP THE BELT SANDER

1. Be certain that the the switch is
off and the power circuit voltage
is the same as the voltage shown
on the specification plate.
Connect the machine to a power
circuit.

2. Squeeze the trigger (A) Fig. 2 to
start the motor. Release the
trigger to stop the motor.

3. To allow the motor to run without
constantly holding the trigger,
press the trigger switch (A), push
the lock button (B) Fig. 2, and
release the trigger switch.

4. To release the lock button, squeeze the trigger and release.

VARIABLE SPEED

Model 352VS has a Variable Speed Control. The operating speed is adjustable
between 850 SFM (surface feet per minute) and 1300 SFM.

The speed is adjusted by turning the thumbwheel, (C) Fig. 2. The first position
provides the slowest operating speed (850 SFM) while position 6 is the fastest
(1300 SFM). The speed can be changed either when the motor is running or is
stopped.

TRACKING THE ABRASIVE BELT

To prevent excessive wear on both the sander and belt, NEVER allow the
abrasive belt to rub on the sander frame. To make sure that the belt is tracking
correctly, do the following:

Make sure that the trigger switch is “OFF” before con­necting the tool to the power source.

1. Turn the tool over. Hold the rear

handle with the left hand so that
the ring finger and the little
finger rest on trigger (Fig. 3).

2. Squeeze the trigger to start the

motor.

3. Turn the belt aligning screw (A)

in either direction until the edge
of the belt is even with the outer
edge of the rear rubber­covered pulley. The edge of the
belt will extend beyond the
edge of the front pulley.

8

Fig. 3

A

Fig. 2

B

A

C

9

4. Release the trigger to stop the motor. Allow the tool to come to a

COMPLETE STOP before turning it over and putting it down.

ATTACHING AND CARE OF DUST BAG

Attach the dust bag to the sander by
pushing the dust bag tube into the
sander vacuum housing (Fig. 4).

For the most efficient operation,
empty the dust bag when it is
approximately half full. Pull the dust
bag straight out of the vacuum
housing, unzip the rear of the bag,
and shake out the dust. Every so
often, turn the bag inside out and
brush the accumulated dust from
the inside.

Do not operate the tool without a dust bag or a dust collection
system.

SELECTING AN ABRASIVE BELT

The principle abrasive materials used on belts for machine sanding are aluminum
oxide and silicon carbide. Aluminum oxide is the softer of the two, but is tougher
and more suited for woods and soft (non-ferrous) metals. Silicon carbide is
extremely hard and is best suited for surfacing stone, marble, and glass.

Abrasives are classed as open-coated (with grits spaced apart), or closed­coated (with grits close together). Closed coatings provide hard, fast cutting
action for hardwoods and dense metals, while open coatings are more suited
to soft materials and painted surfaces.

To obtain the best finish, start with a “COARSE” grade of abrasive and change
to “MEDIUM” and then to“FINE” as work progresses.

GENERAL SANDING

1. Hold the sander off the work before starting the motor.

2. Lower the sander to the work, touching the rear part of the belt first. Level

the machine when moving it forward.

3. Guide the machine over the work in overlapping strokes. Allow the sander

to do the work.

4. Avoid applying excessive pressure. The weight of the machine is usually

sufficient for a fast smooth finish. A slight increase in pressure may speed
removal of material, but too much pressure will slow the motor and
decrease removal.

Fig. 4

SECURE THE WORK and maintain a FIRM GRIP on the
sander. Friction between the sanding belt and the work will
tend to move the work backward and the sander forward.

ALWAYS be sure that the switch is OFF before connecting
the tool to the power source.

10

9

5. Work back and forth over a fairly wide area to obtain an even surface.

6. Do not let the tool tilt. The edge of the belt can make a deep cuts into the

surface.

7. Do not pause in any one spot during the sanding operation. The belt will

eat into the work and make the surface uneven.

8. Lift the tool from the work before turning the motor off.

9. Always be sure that the motor has completely stopped before putting the tool

down.

FAST SANDING ON ROUGH WORK

To smooth a rough surface quickly,
use a coarse grit abrasive belt. With
the belt positioned diagonally
across the grain, move the tool in
the direction of the grain (Fig. 5)

.

Overlap the strokes and cover the
entire surface, working from both
sides of the board (angle left and
then angle right.) Smooth the
surface by guiding the sander back
and forth with the grain. Change the
belt to a medium grit and follow the
same procedure.

Finish by thoroughly working the grain lengthwise. Change again to a fine grit
and repeat. Always finish sanding with the grain.

REMOVING OLD PAINT AND VARNISH

Read and follow “ADDITIONAL SAFETY RULES FOR
PAINT REMOVAL” section of this manual.

The 352VS is an excellent tool for removing old paint and varnish from flat
surfaces. However, two problems are common: 1) sanding material that loads
the abrasive and, 2) friction heat caused by working too long in one place. To
overcome the loading problem, use a coarse grit open coat abrasive belt and a
single stroke action. Overheating can be avoided by using a fairly quick stroke
and moving to another area quickly. A piece of felt about 1/4" thick can be
inserted under the shoe for fast spot sanding and for working on stubborn
areas of paint and varnish.

SPECIAL SANDING PROCEDURES

Generally, the operator should sand with a back and forth motion. Some
materials and some types of operations, however, require a different
technique. In rough sanding, use the tool at an angle. In spot sanding, use the
tool with only the front pulley touching the surface (especially useful in
smoothing excess glue from wood joints). On metals, slate, marble, or plastic
materials, sanding can be done in all different directions because of a lack of
grain.

Fig. 5

11

DOORS AND MILL WORK

When sanding doors, cabinet frames, sash, storm windows and screens, take
care to avoid working into the cross grain where one member meets another.
Notice that the right edge of the belt is visible on the sander. Work carefully
along the edge where the rail meets the stile. If the joint is slightly uneven, use
a fine abrasive and very light sanding pressure to smooth it before making
finishing runs.

For lengthy work on walls or other vertical surfaces, balance the tool with a
length of sash cord, two small pulleys, a light wood frame, and a weight that is
the same as, or slightly less than, the weight of the sander. The frame consists
of two pieces leaning against a wall with a third piece nailed to their top ends.
The two pulleys are located so that the weight on one end of the cord will be
out of the way, but will balance the sander fastened to the other end. When
starting vertical work, angle the sander so you can see that the belt makes
contact with the material. As the belt touches, level the machine and make the
stroke away and to the left. This movement will offset the tendency to cut
heavily into the work at the start of the stroke.

GOOD SANDING TECHNIQUE

Getting to know the sander is most important in obtaining smooth results with a
minimum of labor. Operators will quickly learn how to start a stroke with a
sweeping motion to produce the best results. Use a long even stroke without
additional pressure on the tool. Overlap each stroke and vary the length of
movement so the results will be even. Always lift the tool from the work before
starting and stopping the motor.

BE CAREFUL when sanding at the
end of a board. Keep the tool level
and flat on the work surface. Don’t
let the front of the tool drop. (Fig. 6).
If this happens, it will round the
edge.

The model 352VS sander works very fast and can do a thorough job in a fraction
of the time required by hand sanding. Do not rush the job. Give every surface a
thorough sanding with each grade of abrasive before changing to finer grits.
Always use the abrasive material and grit size recommended for the particular
job.

SANDING METAL

Use the Belt Sander to obtain a grained satin finish on metal. A special
graphite pad is available to replace the steel shoe on the bottom of the sander.
The softness of this pad aids in blending the graining. The pad is the proper
length for sanders using a 3" x 24" belt. For sanders using shorter belt lengths,
cut the pad so that it is the same length as the steel shoe. Replace the steel
shoe with the graphite pad.

Fig. 6

12

KEEP TOOL CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts
should be cleaned with a soft damp cloth. NEVER use solvents to clean
plastic parts. They could possibly dissolve or otherwise damage the material.

Wear safety glasses while using compressed air.

FAILURE TO START

Should your tool fail to start, check to make sure the prongs on the cord plug
are making good contact in the outlet. Also, check for blown fuses or open
circuit breakers in the line.

LUBRICATION

This tool has been lubricated with a sufficient amount of high grade lubricant
for the life of the unit under normal operating conditions. No further lubrication
is necessary.

BRUSH INSPECTION AND LUBRICATION

For your continued safety and electrical protection, brush inspection and
replacement on this tool should ONLY be performed by an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA
FACTORY SERVICE CENTER.

At approximately 100 hours of use, take or send your tool to your nearest
authorized Porter-Cable Service Station to be thoroughly cleaned and
inspected. Have worn parts replaced and lubricate with fresh lubricant. Have
new brushes installed, and test the tool for performance.

Any loss of power before the above maintenance check may indicate the
need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE
TOOL UNDER THIS CONDITION. If proper operating voltage is present, return
your tool to the service station for immediate service.

SERVICE AND REPAIRS

All quality tools will eventually require servicing or replacement of parts due to
wear from normal use. These operations, including brush inspection and
replacement, should ONLY be performed by either an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA FACTORY
SERVICE CENTER. All repairs made by these agencies are fully guaranteed
against defective material and workmanship. We cannot guarantee repairs
made or attempted by anyone other than these agencies.

Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.).

MAINTENANCE

13

ACCESSORIES

A complete line of accessories is available from your Porter-Cable ·
Delta Supplier, Porter-Cable · Delta Factory Service Centers, and
Porter-Cable Authorized Service Stations. Please visit our Web Site
www.porter-cable.com for a catalog or for the name of your nearest
supplier.

Since accessories other than those offered by Porter­Cable· Delta have not been tested with this product,
use of such accessories could be hazardous. For

safest

operation

, only Porter-Cable · Delta recommended

accessories should be used with this product.

14

PORTER-CABLE LIMITED

ONE YEAR WARRANTY

Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.

ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.

To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE •DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE

•

DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,

Contractor’s Saw

®

, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®,

Flying Chips™, FRAME SAW

®

, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®,

Micro-Set

®

, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-

CABLE

®

&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design), QUICKSET™,

QUICKSET II

®

, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®,

Sawbuck™, Sidekick

®

, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber

Company

®

&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,

TORQBUSTER

®

, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®,

Unisaw

®

, Univise®, Versa-Feeder®, VERSA-PLANE®, WHISPER SERIES®, WOODWORKER’S CHOICE™.

Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other
countries. Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y
también pueden estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets
d’invention et marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.

PORTER-CABLE • DELTA SERVICE CENTERS

(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)

(CENTRE DE SERVICE PORTER-CABLE • DELTA)

Parts and Repair Service for Porter-Cable •Delta Power Tools are Available at These Locations

(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable

•

Delta)

(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)

Authorized Service Stations are located in many large cities. Telephone [phone] or 731-541-6042 for assistance locating one. Parts and
accessories for Porter-Cable

•

Delta products should be obtained by contacting any Porter-Cable •Delta Distributor, Authorized Service

Center, or Porter-Cable

•

Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to

the nearest Porter-Cable

•

Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.

Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter­Cable

•

Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable •Delta, Centro de Servicio Autorizado o Centro

de Servicio de Fábrica Porter-Cable

•

Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de

Servicio de Fábrica Porter-Cable

•

Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au

800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter­Cable

•

Delta, s’adresser à tout distributeur Porter-Cable •Delta, centre de service agréé ou centre de service d’usine Porter-Cable •Delta. Si

vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable

•

Delta le

plus proche.

Printed in U.S.A. PC-0403-150

ALBERTA

Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: [phone]
Fax: [phone]

BRITISH COLUMBIA

8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: [phone]
Fax: [phone]

MANITOBA

1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: [phone]
Fax: [phone]

ONTARIO

505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: [phone]
Fax: [phone]

QUÉBEC

1515 Ave.
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: [phone]
Fax: [phone]

1447, Begin
St-Laurent, (Montréal), Québec
H4R 1V8
Phone: [phone]
Fax: [phone]

ARIZONA

Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: [phone]
Fax: [phone]

CALIFORNIA

Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: [phone]
Fax: [phone]
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: [phone]
Fax: [phone]

COLORADO

Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: [phone]
Fax: [phone]

FLORIDA

Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: [phone]
Fax: [phone]
Tampa 33609
4538 W. Kennedy Boulevard
Phone: [phone]
Fax: [phone]

GEORGIA

Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: [phone]
Fax: [phone]

ILLINOIS

Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: [phone]
Fax: [phone]

Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: [phone]
Fax: [phone]

MARYLAND

Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: [phone]
Fax: [phone]

MASSACHUSETTS

Braintree 02185 (Boston)
719 Granite Street
Phone: [phone]
Fax: [phone]

Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: [phone]
Fax: [phone]

MICHIGAN

Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: [phone]
Fax: [phone]

MINNESOTA

Minneapolis 55429
5522 Lakeland Avenue North
Phone: [phone]
Fax: [phone]

MISSOURI

North Kansas City 64116
1141 Swift Avenue
Phone: [phone]
Fax: [phone]

St. Louis 63119
7574 Watson Road
Phone: [phone]
Fax: [phone]

NEW YORK

Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: [phone]
Fax: [phone]

NORTH CAROLINA

Charlotte 28270
9129 Monroe Road, Suite 115
Phone: [phone]
Fax: [phone]

OHIO

Columbus 43214
4560 Indianola Avenue
Phone: [phone]
Fax: [phone]

Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: [phone]
Fax: [phone]

OREGON

Portland 97230
4916 NE 122 nd Ave.
Phone: [phone]
Fax: [phone]

PENNSYLVANIA

Willow Grove 19090
520 North York Road
Phone: [phone]
Fax: [phone]

TEXAS

Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: [phone]
Fax: [phone]

Houston 77055
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: [phone]
Fax: [phone]

WASHINGTON

Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: [phone]
Fax: [phone]