7” Swivel Screen Portable DVD Player
PDM-0743M
Operation Manual
20060620
p
panying
Important Safety
Instructions
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
POWER SUPPLY:
Connect the supplied adapter to the side of the DVD player in the slot marked “Power
In”. Plug the two-prong end of the power cord to an AC100-240V outlet. If you have
difficulty inserting the plug, turn it over and reinsert it, if the unit will not the used for a
long time, disconnect the plug from the outlet.
NOTE:
Before plugging the power cord into an AC outlet, make sure that all the connections
have been made.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric to
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accom
ersons.
the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OF MOISTURE.
CAUTION: Laser radiation when open. Do not stare into beam.
2
CAUTION: These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
Refer to service manual for servicing instructions.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use near water.
6) Clean only with dry cloth.
Do not block any ventilation openings. Maintain well ventilated conditions around
7)
the product, Do not put product on bed, sofa or anything that blocks ventilation.
Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15) Apparatus shall not be exposed to dripping or splashing and no o bjects filled with
liquids, such as vases, shall be placed on the apparatus.
Note: Do not touch the color TFT LCD screen by hand directly.
Important Safety
Instructions
3
S
g
Important Safety
Instructions
Copyright Protection
This product incorporates copyright protection technology that is protected by U.S.
patents and other intellectual property rights. Use of this copyright protection
technology must be authorized by Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
Region code information
DVD players and discs are coded by region. If the region number described on the
DVD disc does not correspond to the region number of this product, this product cannot
play the disc. The region code of this unit is 4.
IMPORTANT FOR LASER PRODUCT
1. CLASS 1 LASER PRODUCT
2. DANGER: Visible laser radiation when open and
interlock failed or defeated. Avoid direct exposure to
beam.
3. CAUTION: Do not open the top cover. There are no
user serviceable parts inside the unit. Leave all
servicin
to qualified service personnel.
4
A
High-quality audio and video
Excellent sound: Dolby Digital
Decoder delivers great sound.
Advanced Playing Functions
Compatibility: Compatible DVD, CD
and JPEG discs, etc.
Particular Performance:
Multi-speed, fast forward, fast
backward, slow playback and
repeated playback.
Last Memory Playback: Memorizes
the stopped playback track and
continues playing the disk from this
spot when the power is on. (Only
available for DVD and CD disc).
Other Special Functions
High Resolution: MPEG-2 decoding
format achieves more than 500 lines
of horizontal resolution.
Features
V input: External Audio, Video
input can be connected to most
external A V sources.
AV Out put: Analog audio output can
be connected to external amplifier.
On-Screen Display: You can choose
from multiple languages for the
On-Screen Display language.
Search by Time: Search for a
certain track of a disk by selected
time.
Special Functions: Supports screen
multi-angle viewing, zooming
function and foul language filtering
.
function
Power Adapter Switch:
Automatically adapts to voltage
requirements in U.S and other
countries.
5
Accessories
Accessories List
ITEM NAME QTY
Remote Control (with battery) 1
Power Supply Cord with AC Adapter 1
Rechargeable Battery Pack 1
DC Adapter (Car Adapter) 1
Audio/Video Cable 1
Earphone 1
Bag 1
Operation Manual 1
：
NOTE
Accessories and their parts numbers are subject to change without prior notice.
6
Important Safety Instructions
Features
Accessories
View of Front Panel
View of Side Panels
View of Bottom Panel
Revolving LCD Screen
Remote Control
System Connections
Power Supply Preparation
Rechargeable Battery
Notes on Discs
Playback Operation
System Setup
Definition
Troubleshooting
Specifications
DVD Playback
CD Playback
JPEG Playback
Contents
……………………………………………..2
………………………………………….….5
………………………………………….….6
………………………………………..…...8
…………………………………….… ….10
…………………………………………....11
…………………………………………....12
…………………………………………....13
……………………………………..……..16
…………………………………..………..18
………………………………………..…..19
………………………………………..…..22
……………………………………..……..23
…………………………………………....24
…………………………………………....27
…………………………………….…….. 28
…………………………………………... 30
……………………………………….…...36
…………………………………………... 37
…………………………………………... 39
7
View of Front Panel
8
1. LCD screen
2. //+ Button
: Press to select different items.
: Press to pause the playback.
+: Press the Mode button and then press this button to increase the level of
brightness, contrast and color.
3. //- Button
: Press to select different items.
: Press to stop playback. Then press the (PLAY) button to resume playback
from the stopped spot. Press this button twice to stop playback completely.
-: Press the Mode button and then press this button to decrease the level of
brightness, contrast and color.
4. // Button
: Press to select different items.
: Press and hold it for several seconds to search backward fast.
: Press to return to the previous list/track/chapter.
5. // Button
: Press to select different items.
: Press and hold it for several seconds to search forward fast.
: Press to go to next list/track/chapter.
6. ENT/(PLAY) button
ENT: Press to confirm selection.
(PLAY): Press to start playback.
7. Speaker
8. Disc tray cover
When the disc is loaded gently press the cover to close it.
9. MENU Button
Press to access the DVD disc menu during playback.
10. SETUP Button
Press to access or exit the system setup menu.
11. MODE Button
Press to enter the brightness, contrast or color adjusting mode.
Press and hold for several seconds to change the aspect ratio among 16:9,4:3
16:9 overturn and 4:3 overturn.
12. ZOOM button
Press to realize various zoom functions.
13. OPEN Switch
Push to open the disc tray cover.
14. SLOW button
Press to activate slow playback function.
15. A-B Repeat button
Press to play a section of the disc from point A to point B.
16. Remote Sensor
17. Charge Indicator
Light is red when the battery is being charged; green when it is fully charged.
View of Front Panel
9
View of Side Panels
Right Side View
1. Volume Control knob
2. Headphone Jack
3. Audio Input/Output Jack
4. Video Input/Output Jack
5. AV IN/OUT Switch
6. DC 9.5/12V Input Jack
Used to adjust the volume of the headphone and speaker.
Used to connect to headphones for private listening. When headphone is plugged,
the speakers will turn off automatically.
For connecting to an external amplifier or audio source.
for connecting to an external monitor or video source.
Switch to “IN” to input external Audio/Video signal. Switch to “OUT” to play disc or
output AV signal.
Used to connect the DC 9.5/12V adaptor.
Left Side View
1. HOLD button
Push the HOLD switch to lock the function of all the buttons on the front panel.
(except the POWER and OPEN switches)
2. Power ON/OFF Switch
Switch the power on or off.
10
1. Rechargeable Battery Contacts
For connecting the rechargeable battery pack.
View of Bottom Panel
11
Revolving LCD Screen
Revolving Steps
The revolving LCD screen is one of the outstanding features about this product. We’d
like to suggest you to take the following steps for proper operation.
Pos. A
Pos. B
1. Open the screen cover to position
(A) as shown in left figure at which
the screen is vertical to the operation
panel.
2. Revolving the screen horizontally
about it’s axis in the clockwise only.
The maximum revolving degree is
180 (position C). If you want to return
to initial position (A), please revolve
screen counter clockwise until it
clicks.
Pos. C
Pos. D
3. You can rotate the screen vertically
from position C to the operation panel
as indicated in left fig.
4. The final rotating position (position D)
at which the screen facing upward
and back to operation panel.
12
1. MUTE button
Press to turn off or on the speaker output.
2. INFO button
Press repeatedly to display or cancel the detailed information of the disc during
playback.
3. TITLE button
Press to display title menu if it exits in the disc.
4. Direction button
Press to select different options.
5. ENTER button
Press to access playback or confirm your selection.
6. SETUP button
Press to enter the player’s setup menu.
Remote Control
13
Remote Control
7. 0-9 number buttons
Select numbers by pressing these buttons.
8. NEXT button
Press to skip to the next list, track or chapter.
9. PREV button
Press to return to the previous list, track or chapter.
10. SUBT button
When playing a DVD coded with multi-subtitles, press to select a subtitle
language or to turn subtitles off.
11. ANGLE button
Press to access various camera angles if the DVD disc contains multiple camera
angles.
12. A-B button
Press to play a section of the disc from point A to point B. Press once to select the
starting point A, press again to select the end point B. During A-B repeat playback,
press this button to stop the repeat.
13. ZOOM button
Press to realize various zoom functions.
14. REP button
Press to repeat a chapter, title or the entire disc.
15. MENU button
Press to access the DVD disc menu during playback.
16. PAUSE button
Press to pause playback. Press the PLAY button to resume normal playback.
17. STOP button
Press to stop playback. Then press the PLAY button to resume playback from the
stopped spot. Press this button twice to stop playback completely.
18. PLAY button
Press to start playback.
19. +10 button
select number greater than 9 by pressing the (+10) button first, and then
additional number buttons as needed.
20. GOTO button
Press to select the desired disc starting time, title or chapter.
21. REV SCAN button
Press to search backward fast during playback.
22. FWD SCAN button
Press to search forward fast during playback.
23. SLOW button
Press to activate slow playback function.
24. AUDIO button
Press to select different languages when a DVD disc with multiple audio
languages is played. Press to select different audio track when a CD disc is
played.
14
Remote Control
Preparation of Remote Control
Follow the steps below to install the battery.
1. Pull the battery holder out from the remote control in the direction of the arrow.
2. Load a new battery properly with the (+) sided up.
3. Insert the battery holder back into the remote control.
Battery type: CR2025 3V
Battery service life: approximately 1 year under normal use (at room temperature).
Use of Remote Control
Point the remote control unit to the remote sensor within the range of 16 feet and
angles of 60 degree, and without obstacles between remote control and remote sensor.
Note
¾ Improper use of the battery may cause
overheating, explosion or ignition, which
can result in an injury or a fire. Battery
leakage may damage the remote control.
¾ Do not expose the remote control unit to
direct sunlight.
¾ Do not recharge, disassemble, deform or
heat the battery.
¾ Do not put the battery in fire or water.
¾ Immediately replace the exhausted
battery.
¾ Take out battery when the rem ote is not in
use for a long time.
15
System Connections
z Always ensure that the DVD player, TV and any other electrical equipment to be
connected with are switched off and unplugged from the power supply.
z Ensure that you observe the color coding when connecting audio and video
cables.
Connecting to TV
Follow the drawing below to connect the DVD player to TV's Audio/Video input with
Audio/Video cable.
Connecting to An Amplifier
Refer to your audio equipment's manual before connection.
Follow the drawing below to connect the DVD player to AV amplifier.
16
System Connections
Connecting to External AV Source
The player supports an AV signal input function. Use the audio/video cable to connect
the unit to an external AV signal source such as a DVD, VCR etc. After connecting,
switch the DVD/AV IN to AV IN.
NOTE: Noise may occur in speakers when there is an external audio signal input while
playing a DVD disc. Unplug the audio cord to clear the noise.
Connecting to the Headphones
Connect the headphones to the headphone jack on either side of the player.
When headphone is connected, the speakers will automatically turn off.
17
Power Supply Preparation
Using the AC Adapter
The player is supplied with an AC adapter for powering the unit and charging the
battery.
1. Connect AC adapter to the left side of
the DVD player in the jack marked DC
9.5/12V IN as shown on the right.
2. Plug the two-prong end of the power
cord into a grounded electrical outlet.
The power indicator lights red.
Note: 1. Turn player's power off before unplugging.
2. In the case of using the adapter, the LCD screen will be brighter than using the
rechargeable battery.
Using of Car Adapter
The player is supplied with a Car Adapter for powering the unit and charging the battery
in a vehicle.
Connect the car adapter power plug to
the unit's power jack and the other end to
the vehicle’s 12V accessory/cigarette
lighter socket as the right figure.
Attention
¾ Do not operate the unit or view video software while driving a vehicle.
¾ Place the unit in a proper position for viewing.
¾ Detach battery pack when using the AC or car adapter as power source.
¾ Disconnect the player from the Car Adapter when starting the vehicle.
18
Rechargeable Battery
About Rechargeable Battery Pack
Your portable DVD player comes with a lithium ion rechargeable battery that attaches
to the bottom of the DVD player. Charge the battery fully before initial use. Charging
time is normally about 5 hours. A fully charged battery delivers about 3 hours of use but
playing time varies from disc to disc. If the battery will not be used for a long period of
time, charge the battery fully before storage.
Working conditions and precautions for the rechargeable battery
¾ New battery should be fully charged before initial use.
¾ Battery should only be used and charged when temperature is between 32-100F .
¾ Never put the battery in fire or water.
¾ Do not expose the battery to high temperature or store in hot, sunny place.
¾ Maintain well-ventilated conditions around the product to avoid overheating.
Don’t put the product on a bed, sofa or anything that may block ventilation to the
product.
¾ Do not short the battery terminals.
¾ Do not open the battery.
¾ Detach the battery after charging is complete. When charging the batter y pack,
the charge light will turn red, when the charging is complete, the light will turn
green.
¾ Detach the battery when it is not in use.
¾ When the charge of the battery is weak, low power indicator will appear on the
LCD screen. The player will turn off automatically several minutes later.
Warning:
Do not touch any metal object to the battery connectors, as it will put the battery in
standby mode. To exit the standby mode, connect the battery and DVD player to AC or
DC power.
19
Rechargeable Battery
Attaching the Battery Pack
Refer to the following steps for attaching the Battery Pack:
1. With one hand on the DVD Player to prevent it from moving, take the battery and
align the plastic tabs on the battery pack with holes on the player, and push the
battery pack into the DVD Player.
2. Slide the Battery Pack until you hear it click and lock into place.
Charging the Battery Pack
The battery pack must be attached to the DVD player to charge it by using the supplied
AC Power Adapter.
1. Attach the battery pack to the DVD player.
2. Plug the supplied AC Power Adapter into the player’s power jack marked with “DC
9.5/12V IN”, which is located on right side of the DVD Player.
3. Plug the other end of the AC Power Adapter Cord into a household AC Outlet as
shown below:
20
Rechargeable Battery
Detaching the Battery Pack
When being turned off, the DVD Player still consumes some power in standby mode.
This will eventually discharge the battery. If the DVD Player is not going to be used for
long periods of time, the battery pack should be detached.
Make sure the power is turned off before detaching the Battery Pack.
1. Press and hold the Battery Release Tab in the direction of the arrow ① as shown
in Fig.1 below.
2. Slide the Battery Pack gently towards the direction of the arrow ② as shown in
Fig.1 below.
3. Carefully remove the Battery Pack from your player.
21
Notes on Discs
Compatible Disc Formats
DISC LOGO DIAMETER
12cm
DVD
8cm
CD
12cm 74 min
8cm 20 min
PLAYBACK TIME/
PLAYABLE SIDES
133 min (SS-SL)
242 min (SS-DL)
266 min (DS-SL)
484 min (DS-DL)
41 min (SS-SL)
75 min (SS-DL)
82 min (DS-SL)
150 min (DS-DL)
JPEG
Operation methods of some DVD discs are specified by the software manufacturer.
Please follow the instructions of the disc.
12cm
Care of Discs
Holding Discs
When loading or removing discs, try not to touch their playing
surfaces as the right figure.
Cleaning
Fingerprints or stain on the disc may affect the quality of sound and
picture. To clean your discs, use a soft clean cloth to wipe them. If
necessary , moi sten a sof t clot h w ith dilu ted ne utral d etergen t to rem ov e
heavy dirt or fingerprints.
Do not wipe in a circular direction as the figure in the right middle
(concentric scratches on the disc groove tend to cause noise). Gently
wipe from the center of the disc to the outer edge as the right figure.
22
PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY BEFORE USING
YOUR DVD PLAYER FOR THE FIRST TIME.
WARNING: Do not play poor quality discs to avoid damaging the lens.
Playback Operation
Pre-operation
1. Connect the unit to power supply through the provided AC adaptor.
2. Switch “POWER ON/OFF” to “ON” to turn on the DVD player.
3. Push the OPEN switch on the unit to open the disc tray cover. Put a disc in the
disc tray with printed side up. Close the disc cover. (See below)
4. The player will search disc and play it automatically.
5. Adjust the volume with the VOLUME control on the right panel to the desired level.
6. To turn the player off, switch the POWER ON/OFF on the left panel to OFF.
Basic Operation
MODE button
Press the MODE button and then press the /+ or /-
button to adjust brightness, contrast and color of the
screen.
Press the MODE button and hold it for sev eral se conds to
change the aspect ratio among 16:9,4:3 16:9 overturn
and 4:3 overturn.
23
Playback Operation
DVD Playback
ENTER/ENT
button
PAUSE/
button
STOP/ button
MENU button
TITLE button
ZOOM button
Load a disc in, the player will search the disc and play it
automatically. Press the direction buttons () to
highlight the item that you want to play and press the
ENTER/ENT button to confirm.
Press the PAUSE/button to pause during playback and
press the PLAY/(PLAY) button to resume normal
playback.
During playback, press the STOP/ button once to stop
playback and then press the PLAY/(PLAY) button to
resume normal playback from the place where the
STOP/ button is pressed. Press the STOP/button
twice repeatedly to stop playback completely.
Press the MENU button during playback. The root menu
will appear on the screen.
Press the direction buttons () to select the item
you wish to play, and press the ENTER/ENT button to
confirm. Or press the 0-9 and +10 butto ns to select the
item you prefer directly.
In general, the content of a DVD disc can be divided into
several titles, and also there are several menus in a title.
Press the TITLE button during playback. The title menu
will appear on the screen. Press the direction buttons
() to select the title or disc menu item you want
to watch and then press the ENTER/ ENT button to
confirm. Or press the 0-9 and +10 butto ns to select the
item you prefer directly.
Press the ZOOM button repeatedly to shift among 2x - 3x
- 4x - 1/2 - 1/3 - ¼ zooming effect and normal playback.
24
DVD Playback (continued)
& buttons
& buttons
SLOW button
REP button
A-B button
GOTO button
Press the button to go to the previous chapter.
Press the button to play the next chapter.
Press the / button (and hold it for several seconds)
to start fast forward/rew ind pl ay back. P ress i t (and hold it
for several seconds)
at the speed of 2X, 4X, 8X, 16X, 32X and normal in
sequence. Press the PLAY/(PLAY) button to return to
normal playback.
Press the SLOW button repeatedly and slow playback
will at the speed of 1/2 – 1/4 – 1/8 – 1/16 – normal
playback. During slow playback, press the PLAY/
(PLAY) button to resume normal playback.
Press the REP button to repeat a Chapter, All or cancel
repeat in sequence.
In normal playback, press the A- B button to select the
segment that you want to play repeatedly. Press once to
select the starting point A, press again to select the end
point B and the player will play the segment between A-B
continuously. Press the A-B button the third time to
cancel the repeat segment.
During playback, press the GOTO button repeatedly to
enter the menu to select desired TITLE, CHAPTER or
TIME. Use the direction buttons to select the item
you want to set. Use the 0-9 and +10 buttons to select
directly and then press the ENTER/ENT button to
confirm.
Press the GOTO button again to exit.
Playback Operation
repeatedly to fast forward/rewind
25
Playback Operation
DVD Playback (continued)
INFO button
AUDIO button
SUBT button
ANGLE button
Press to display or cancel the detailed information of
the disc during playback.
DVD discs can contain up to 8 audio bit streams. For
example: English, French etc.
To select the audio bit stream you prefer, press AUDIO
button during playback. The DVD player will play the next
audio bit stream every time you press the AUDIO button
in succession.
When a DVD is playing, press the SUBT button to select
a subtitle language or to turn subtitle off. A DVD disc can
be recorded with at most 32 subtitles.
NOTE: This function is available for discs recorded with
multi-subtitles
Press the ANGLE button to play the disc in multi-angle.
Multi-angle means that a scene is shot from different
angle so that audience can w atch f rom a ny angl e, lik e th e
drawings below:
If there are multiple an gles in a scene, you can use the
ANGLE button to select the angle you like to enjoy. Press
the ANGLE button repeatedly to view different angle.
NOTE: This function is only available for the DVD disc
that coded with multi-angle.
26
play
CD Playback
PAUSE/
button
STOP/ button
& buttons
& buttons
GOTO button
INFO button
REP button
AUDIO button
Playback Operation
Press the PAUSE/button to pause during playback.
Press the PLAY/(PLAY) button to resume normal
back.
During playback,pressthe STOP/ button once to stop
and then press the PLAY/(PLAY) button to resume
normal playback from the place where the STOP/
button is pressed. Press the STOP/button twice
repeatedly to stop playback completely.
Press the / button (and hold it for several seconds)
to play fast forward/rewind. Press it (and hold it for
several seconds) repeatedly, the fast forward/ rewind
playback will be undergoing at the speed of 2X, 4X, 8X,
16X in sequence. Press the PLAY/(PLAY) button to
return to normal playback.
Press the button to play the previous chapter.
Press the button to play the next chapter.
During playback, press the GOTO button repeatedly to
enter the menu to select desired track, time track or disc
time. Use the direction buttons to se lect the i tem y ou
want to set. Use the 0-9 buttons to select directly and
then press the ENTER/ENT button to confirm.
Press the GOTO button again to exit.
Press the INFO button repeatedly to display or cancel
detailed information during playback.
Press the REP button repeated to repeat a Track, All or
cancel repeat in seque nce.
Press the AUDIO button to select desired sound effect.
Press it repeatedly and the display will be as follows:
Left Right Stereo
27
Playback Operation
JPEG Playback
Pre-operation
1. Load a JPEG in the disc tray, and the player will search and play disc automatically.
2.The screen displays the root folder with several subdirectories/subfo lders. Use the
, buttons to select desired folder. Then press the ENTER/ENT or PLAY/(PLAY)
button to confirm your selection.
3.The screen enters the sel ected subfolder with sever al files. Use the , buttons to
select desired file. Then press the ENTER/ENT or PLAY/(PLAY) button to confirm
your selection.
4.Press the button to return to prev ious folder or directory.
Note: Many discs have other items besides pictures.
Buttons Operation
STOP/
button
PAUSE/
button
MENU button
& buttons
ZOOM button
Press the STOP/ button to return to the previous fo l der.
Press the direction () buttons to select the
picture you prefer and then press the ENTER/ENT or
PLAY/(PLAY) button to play.
Press the PAUSE/button to pause during playback.
Press the PLAY/(PLAY) button to resume normal
playback.
Press the STOP/ button to return to the previous fo l der.
Press the direction () buttons to select the
picture you prefer and then press the ENTER/ENT or
PLAY/(PLAY) button to play.
Press the button to play the previous chapter.
Press the button to play the next chapter.
Press the ZOOM button repeatedly to shift among 4/3,
3/2, 7/4, 2, 1/4, 1/2 zooming in and out effect and normal
playback.
28
Playback Operation
JPEG Playback (continued)
GOTO button
REPEAT
Function
While viewing a picture, use the direction buttons to rotate the picture.
Press the button to rotate the current picture clockwise:
Press the button to rotate the current picture anti-clockwise:
During playback, press the GOTO button to select the
desired file.
Press the 0-9 buttons directly to select according to your
preference.
Under folder status, press the button to enter REPEAT
setup. Then press the ENTER/ENT button repeatedly to
set the repeat mode and the scree n will displ ay as follows
in sequence: DISC NORMAL DISC
REPEAT SHUFFLE SINGLE TRACK REPEAT
TRACK FOLDER NORMAL FOLDER REPEAT
Press the button to exit.
Picture Rotate
29
System Setup
You can change the default settings of this unit to customize its performance to your own
preference. Read this section to learn how to set up the system.
Note: the system should better be set up in the state that no disc is in the DVD drive or the
unit is on the stop mode.
Follow the steps below to set up your system:
1. Press the SETUP button.
2. The setup menu will appear on the screen. It includes General Setup Page, Speaker
setup page, Dolby digital setup, Video setup page and Preference page. You can exit
the setup menu by pressing the SETUP button again at any time during setting.
3. Press the or (direction buttons) to select a sub-menu that you want to set up.
4. Press the or button to select the item that you want to set up in the sub-menu.
General Setup Page
The items included in this sub-menu are shown as
the left.
1.TV Display
This item is used to set TV display mode.
Press the or button to highlight this item.
Press the ENT orbutton to enter the item.
It includes Normal/PS, Normal/LB and Wide, Wide
by default. Press the or button to choose the
proper one. Press the ENT button to confirm your
selection. Press the direction button to exit from
this item.
Note: Select Normal/PS or Normal/LB when a 4:3
TV is connected.
Select Wide when a 16:9 wide screen TV is
connected.
30
General Setup Page
System Setup
2.Angle Mark
This item is used to turn the Angle Mark on or off.
Press the or button to highlight this item.
Press the ENT or to enter the item.
Press the or button to choose angle mark on
or off.
Press the ENT button to confirm your selection.
Press the direction to exit this item.
3.OSD Language
This item is used to set the OSD (on-screen
display) language. Press the or button to
highlight this item. Press the ENT or to enter the
setup of this item.
It includes English, French, Spanish, German and
Italian, English by Default.
Press the or button to choose the proper one .
Press the ENT button to confirm selection. Press
the direction button to exit this item.
4.Screen Saver
This item is used to turn the screen saver on or off.
Press the or button to highlight this item.
Press the ENT or to enter the setup of this item.
The default setting of this item is on.
Press the or button to choose on or off.
Press the ENT button to confirm selection.
Press the direction button to exit this item.
5. Last Memory
This item is used to set last memory state.
Note: The last memory refers to resume playback
from the point that you stopped last time.
Press the or button to highlight this item.
Press the ENT or to enter the item.
The default setting of this item is on.
Press the or button to choose on or off.
Press the ENT button to confirm selection.
Press the direction button to exit this item.
31
System Setup
Speaker Setup Page
Dolby Digital Setup
The item included in this sub-menu is shown as the
left.
1.Downmix
This item is used to set downmix mode.
Press the or button to highlight this item.
Press the ENT or to enter the item.
It includes Lt/Rt and stereo, stereo by default.
Note: The function of Lt/Rt is to output mixed audio
in the format provided by Dolby. The function of
stereo is to output stereo signal.
Press the or button to choose the proper one .
Press the ENT button to confirm your selection.
Press the direction button to exit this item.
The items included in this sub-menu are shown as
the left.
1. Dual Mono
This item is used to set the channel output mode.
Press the or button to highlight this item.
Press the ENTE or to enter the item.
It includes stereo, L-Mono, R-Mono and Mix-Mono,
Stereo by default.
Press the or button to choose the proper one .
Press the ENT button to confirm your selection.
Press the direction button to exit this item.
32
Dolby Digital Setup
Video Setup Page
System Setup
2.Dynamic
This item is used to adjust linear dynamic
compression rate to get different signal
compression Effects.
Press the or button to highlight this item.
Press the ENT or to enter the setup of this item.
Then the item will show as the left.
Press the or to choose the proper level.
Press the ENT button to confirm your selection.
Press the direction button to exit this item.
The items included in this sub-menu are shown as
the left.
1.Sharpness
This item is used to adjust the sharpness of the
Screen.
Press the or button to highlight this item.
Press the ENT or to enter the item.
It included High, Medium and Low, Low by default.
Press or button to choose the proper one.
Press ENT button to confirm your selection.
Press direction button to exit this item.
2. Brightness
This item is used to adjust brightness level of the
Screen.
Press the or button to highlight this item.
Press the ENT or to enter the item.
Press the or button to adjust to desired level.
The default level is 00.
Press the ENT button to confirm your selection.
33
System Setup
Video Setup Page
Preference Page
3. Contrast
This item is used to adjust contrast level of the
Screen.
Press the or button to highlight this item.
Press the ENT or to enter the item.
Press the or button to adjust to desired level.
The default level is 00.
Press the ENT button to confirm your selection.
The items included in this sub-menu are shown as
the left.
NOTE: This sub-title can only appear in the state
that no disc is in the DVD player.
1. Audio
This item is used to set the audio output language.
Press the or button to highlight this item.
Press the ENTER or button to enter the setup of
this item.
The available languages are English, French,
Spanish, etc.
Press the or button to choose the preferred
Language.
Press the ENTER button to confirm your selection.
Press the button to exit from this item.
34
System Setup
2. Subtitle
This item is used to set the language of subtitle.
Press the or button to highlight this item.
Press the ENTER or button to enter the setup
of this item.
The available languages are French, Spanish,
etc.
Press the or button to choose the
preferred Language.
Press the ENTER button to confirm your
selection.
3. Disc Menu
This item is used to set the language of disc menu.
Press the or button to highlight this item.
Press the ENTER or button to enter the setup of
this item.
The available languages are English, French,
Spanish, etc.
Press the or button to choose the preferred
Language.
Press the ENTER button to confirm your selection.
Press the button to exit from this item.
4. Default
This item is used to reset the unit.
Press the or button to highlight this item.
Press the ENTER button to reset.
Then all the settings of your unit are back to the
original state.
35
Definitions
Letterbox screen
This refers to a screen on which the playback picture of wide-screen DVDs appears with
black bands running along the top and bottom.
Pan & Scan screen
This refers to a screen on which the playback picture of wide-screen DVDs is cut off at the
left and right sides.
Title, Chapter (DVD)
DVDs are divided into some large sections (titles) or some small sections (chapters). Each
section is numbered: these numbers are called Title number or Chapter number.
Title 1 Title 2
Chapter1 Chapter 1
Chapter2
…… ……
Track (CD)
CDs are divided into some sections ( tracks). Each sect ion is numbered; th ese numbers are
called Track number.
Track 1 Track 2 Track 3 ……
JPEG
JPEG is a common picture format that
has small file size and low quality loss
rate of picture. Hundreds of pictures can
be stored in a disc in this format. In
order to utilize real digital album, use film
to make a Picture CD in JPEG format.
36
Troubleshooting
If you suspect there is something wrong w ith the DVD player , imme dia t el y turn the power off.
Disconnect the power connector and check that there is no smoke or excessive heat coming
from the unit.
Never open or try to repair the unit yourself. There are no user serviceable parts inside.
PROBLEM
The player cannot
play.
POSSIBLE CAUSE
The disc cover may not be
closed.
There may be no discs in
the DVD drive.
The disc may not be put in
in the right way.
The disc may be dirty or
warped.
The player's region code
may not as the same as the
region code of DVD disc.
There may be water on the
lens.
POSSIBLE SOLUTION
Close the disc cover.
Put a disc in to the DVD drive.
Put the disc in with the label
side up.
Clean or change the disc.
Make sure the player's
region code is the same as
the region code of DVD
disc.
Remove the disc and keep
the player being powered off
for at least two hours.
There is no sound .
The system connection may
be not correct.
The speakers may be
turned down.
The sound setup of the DVD
disc may be not correct.
The disc may be dirty or
warped.
Connect the system
correctly.
Turn on the speaker.
Setup the sound of the DVD
correctly.
Clean or change the disc.
37
Troubleshooting
PROBLEM
There is no picture.
Poor AV performance.
The remote control
does not work
POSSIBLE CAUSE
The LCD may be not in
correct video mode.
The system connection may
be not correct.
The unit may be not in AV
out mode.
The disc may be dirty or
warped.
There may be some
obstructions between the
remote control and the
player.
The remote control may not
be pointed at the player.
The batteries of remote
control may not be inserted
correctly.
The batteries of remote
control may be out of power
or weak.
POSSIBLE SOLUTION
Choose the correct video
mode.
Connect the system
correctly.
Switch AV IN/OUT on the
right panel to OUT.
Clean or change the disc.
Remove the obstruction
between the remote control
and the player.
Point the remote control at
the player directly.
Make sure the polarity of
each battery is correct.
Replace the batteries.
Other possibilities:
Static or other external interference may cause the player function abnormally. In order to
recover normal status, please unplug the power-supply cord and then plug it into the outlet
again to reset the player. If the problems still exist, please cut off the power supply and
consult your service center or the qualified techn i ci an.
38
TFT screen size
7 inches (16：9)
Specifications
Screen resolution 480x234
Laser Wavelength 780/650nm
Video System NTSC
Frequency Response 20Hz-20kHz ±2.5dB
Audio Signal-to-noise Rate ≥85dB
Audio distortion + noise ≤ -70dB (1kHz)
Channel Separation ≥70dB (1kHz)
Dynamic Range ≥80dB (1kHz)
Audio Out Out Level 2V±
0.2
, Load 10kΩ
1.0
Video Out
Out Level 1V
Unbalanced Negative
±0.2, Load 75Ω
P-P
Power AC100～240V（50/60Hz）
Dimensions 202mm x 150mm x 40mm
Weight Approximate 0.75 Kg
DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works.
Manufactured under license from Dolby Laboratories.
© 1992 -1997 Dolby Laboratories, Inc.
All rights reserved.
39
For service, support and warranty information, visit www.polaroid.com
the US call 1-866-289-5168 or in Canada call 1-866-301-7922.
"Polaroid" and “Polaroid and Pixel” are trademarks of Pol aroid Corporation,
Waltham, MA, USA.
or in
40
Loading...