Page 1
2. Installation Precautions
Quick Installation Guide
WNAP-6335
300Mbps 802.11n Wireless Outdoor CPE
1. Package Contents
Thank you for choosing PLANET WNAP-6335. Before installing the
AP, please verify the contents inside the package box.
WNAP-6335 Quick Guide
PoE Injector & Power Cord
Plastic Strap x 1
Caution
IMPORTANT SAFETY PRECAUTIONS:
1) LIVES MAY BE AT RISK! Please be aware of
the electrical wires around, and tighten the pole.
Carefully read the section "OUTDOOR
INSTALLATION WARNING" in the manual
before installation.
2) Users MUST use the “PoE Injector” and
“Power Cord” shipped in the box with the
WNAP-6335. Otherwise, the product might be
damaged.
3) Users MUST use a proper and well-installed
surge arrestor and grounding wired with the
WNAP-6335; otherwise, a sudden lightning
could cause fatal damage to the WNAP-6335.
EMD (Lightning) DAMAGE IS NOT COVERED
UNDER WARRANTY.
4) Users MUST have the antenna connected
first before powering on the WNAP-6335;
otherwise, damage to the WNAP-6335
might happen.
5) The Antenna is required, and must be purchased
separately.
If there is any item missing or damaged, please
Note
contact the seller immediately.
– 1 – – 2 –
3. Physical Introduction
Rear Panel Description – LED Indication
Power LED LAN 1 LED
Wireless LEDLAN 2 LED
Bottom Panel Description – Port
Grounding Terminal
Reset Button
4. Hardware Installation
STEP 1: (A) Push the latch on the bottom of the WNAP-6335
to remove the sliding cover.
(B) Plug the RJ45 Ethernet cable into the PoE LAN Port and
connect the external antenna to the RP-SMA connectors of
the WNAP-6335. Then, slide back the cover of the
WNAP-6335 to finish the installation.
PoE LAN
LAN2
RP-SMA
– 3 – – 4 –
RP-SMA(Male) to N-male Cable
Page 2
STEP 2: Plug the power cord into the DC port and the other
side into the AC socket. Then, plug the RJ45 cable
(as shown in picture 4 under Step 1) into the POE
port of the PoE injector.
Ethernet Cable
PoE Port
Ethernet Cable
Data+Power
Data
24V PoE Injector
2
LAN POE
PC
1
Power
Data In
PoE Out
5. Pole Mounting
STEP 1:
Place the strap through
the slot on the back of
the WNAP-6335 and
then around the pole.
Tighten the strap to
secure the WNAP-6335.
6. Web Login
Connect the WNAP-6335 with your PC via the PoE injector where
one end of an Ethernet cable is plugged into the LAN port of the
PoE injector while the other end into the LAN port of the PC. Power
on the WNAP-6335 via the PoE injector.
1. Click the “Start” button located in the lower-left corner of
your computer.
2. Click “Control Panel”.
3. Double-click the “Network and Sharing Center” icon.
4. Click “Change Adapter Settings”.
5. Double-click “Local Area Connection”.
6. Select “Internet Protocol Version 4 (TCP/IPv4)” and
click “Properties”.
7. Select “Use the following IP address”, and then click
“OK” button twice to save the configuration. For example,
as the default IP address of the WNAP-6335 is
192.168.1.253 and the router is 192.168.1.254, then you
may choose from 192.168.1.1 to 192.168.1.252.
– 5 – – 6 –
Default IP Address: 192.168.1.253
Default Username: admin
Default Password: admin
Default SSID: WNAP-6335
STEP 1: The Web management allows you to access and
manage the wireless AP easily. Launch the Web
browser and enter the default IP address
http://192.168.1.253.
STEP 2: When the login window pops up, please enter the
User Name and Password. The default User Name
and Password are both “admin”. Then click the OK
button to continue.
For security reasons, it is recommended to change the
password at the first login and memorize it.
– 7 – – 8 –
STEP 3: After you enter into the Web User Interface, go to
Wireless Basic Settings to configure your wireless
network.
Further Information:
The above steps introduce the simple installations
and configurations of the WNAP-6335. For further
configurations of different operation modes, please
refer to the user manual which can be downloaded
from the website.
http://www.planet.com.tw/en/support/download.p
hp?type1=4&model=48687&type=3
If you have further questions, please contact the local dealer or
distributor where you purchased this product.
2011-E10600-000
Loading...