PLANET WNAP-6325 User Manual

2. Installation Precautions

Quick Installation Guide

WNAP-6325

300Mbps 802.11n Wireless Outdoor CPE

1. Package Contents

Thank you for choosing PLANET WNAP-6325. Before installing the AP, please verify the contents inside the package box.

WNAP-6325 Quick Guide

PoE Injector & Power Cord

Plastic Strap x 1

1. Users MUST use a proper and well-installed surge arrestor and grounding wired with the WNAP-6325; otherwise, a sudden lightning could cause fatal damage to the WNAP-6325.

EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.

Caution

2. Users MUST use the “Power cord and PoE Injector” shipped in the box with the WNAP-6325. Use of other options will cause damage to the WNAP-6325.

3. Physical Introduction

Rear Panel Description – LED Indication

Power LED LAN 1 LED

If there is any item missing or damaged, please

Note

contact the seller immediately.

– 1 – – 2 –

Bottom Panel Description – Port

Grounding Terminal

Reset Button

LAN2 PoE LAN

4. Hardware Installation

STEP 1: (A) Push the latch on the bottom of the WNAP-6325

to remove the sliding cover.

1 2

Wireless LEDLAN 2 LED

(B) Plug the RJ45 Ethernet cable into the PoE LAN Port of the

WNAP-6325. Then, slide back the cover of the WNAP-6325 to finish the installation.

3 4

STEP 2: Plug the power cord into the DC port and the other

side into the AC socket. Then, plug the RJ45 cable (as shown in picture 4 under Step 1) into the POE port of the PoE injector.

Ethernet Cable

PoE Port Ethernet Cable

Data+Power

Data

24V PoE Injector

Power

– 3 – – 4 –

LAN POE

Data In

PoE Out

5. Pole Mounting

6. Web Login

STEP 1: Place the strap through the slot on the back of the

WNAP-6325 and then around the pole. Tighten the strap to secure the WNAP-6325.

IMPORTANT SAFETY PRECAUTIONS:

1) LIVES MAY BE AT RISK! Please be aware for the electric wires around, and tighten the pole. Carefully read the section "OUTDOOR INSTALLATION WARNING" in the manual before installation.

Caution

2) Users MUST use the “Power cord and PoE Injector” shipped in the box with the WNAP-6325. Otherwise, the product might be damaged.

Connect the WNAP-6325 with your PC by an Ethernet cable plugging in LAN port of PoE injector in one side and in LAN port of PC in the other side. Power on the WNAP-6325 by PoE from PoE injector.

1. Click “Start” button located in the lower-left corner of your computer.

2. Click “Control Panel”.

3. Double-click “Network and Sharing Center” icon.

4. Click “Change Adapter Settings”.

5. Double-click “Local Area Connection”.

6. Select “Internet Protocol Version 4 (TCP/IPv4)” and click “Properties”.

7. Select “Use the following IP address”, and then click “OK” button twice to save the configuration. For example, as the default IP address of the WNAP-6325 is

192.168.1.253 and the router is 192.168.1.254, then you may choose from 192.168.1.1 to 192.168.1.252.

– 5 – – 6 –

Default IP Address: 192.168.1.253 Default Username: admin Default Password: admin Default SSID: WNAP-6325

STEP 1: The Web management allows you to access and

manage the wireless AP easily. Launch the Web browser and enter the default IP address

http://192.168.1.253.

STEP 2: When the login window pops up, please enter the

User Name and Password. The default User Name and Password are both “admin”. Then click OK button to continue.

STEP 3: After you enter into the Web User Interface, go to

Operation Mode to configure your wireless network.

Further Information:

The above steps introduce the simple installations and configurations of the WNAP-6325. For further configurations of different operation modes, please refer to the user manual which you can download from the website.

http://www.planet.com.tw/en/support/download.php?type1=4& model=48589&type=3

For security reasons, it is recommended to change the password at the first login and memorize it.

– 7 – – 8 –

If you have further questions, please contact the local dealer or distributor where you purchased this product.

2011-E10590-000