Planet NAS-7103 Installation Manual

NAS-7103 NAS-7103

Note :

1. Please do not connect
computer with RJ-45 Ethernet
cable and USB2.0 (TYPE B)
cable at the same time.

2. Your NAS-7103 will require to
store firmware and some
basic information to your
newly installed HDD. If you'd
replace a new HDD to the NAS-7103, pleae follow the steps above
again to keep the informaiton for NAS-7103.

VERIFY THE CONTENTS INSIDE PACKAGE BOX

The package should contain the items plus NAS-7103. If any item is missing or damaged, please contact the seller immediately.

STEP 1 : Hardware Installation

STEP 2 : Firmware Installation

For the first time installation or New HDD installation.

Power Adapter

CD-ROM

NAS-7103

Brackets RJ-45 Cable

Case Screw x 2

Quick Installation Guide HDD Screw x 4USB2.0 Cable (TYPE B)

1-1. Loosen the screws on the bottom of the case.

1-3. Secure the HDD with the HDD screws at

both ends.

1-4. Push the tray back into the case and tighten

the bottom screws.

Note :

If any of above items are missed or damaged, please contact your local dealer for support.

1-2. Place the HDD on the tray.

Steps Description

 Connect NAS-7103 and a PC with USB2.0 Cable

(TYPE B).



In the CD along with the product, run “NAS

Config.exe” to search and select the device.

 Click “Browse” and select the firmware file, Click

Upgrade button to install firmware.

2-2. Follow the steps below for the first time HDD installation

2-1. Device installation







Quick GuideQuick Guide

2011-AB2220-000

PLANET Technology Corporation

Tel: [phone] Fax: [phone]
Email: [e-mail] www.planet.com.tw

11F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)

PLANET reserves the right to change specications without prior notice. All brand names and trademarks are property of
their respective owners. Copyright © 2012 PLANET Technology Corp. All rights reserved.

STEP 4 : Web Management

STEP 3 : Access Your NAS-7103 through Network

Steps Description



Connect NAS-7103 and a Switch, Hub, Router, or computer with RJ-45 Ethernet cable.

 [Optional] Connect USB storage device(s) to this device with USB cable(s). NAS-7103 can automatically mount the

USB devices connected.



Connect the power supply to NAS-7103.



Press the “Power button” to turn on NAS-7103. NAS-7103 will be ready to use when the blue LED lights up steady.









DHCP Client PC or IP:192.168.0.x

1. Install "NAS Finder" for Windows utilit from the CD.

2. Please go to Start



Program  PLANET  NAS-7103  NAS Finder. And

click on Refresh button to find your NAS-7103 in the network. The NAS Finder will

list the NAS-7103 connected in the Ethernet Network with its Model Namd and IP

address.

3. [DHCP server available in the Network] Double click on the selected item and the

program should automatically access the NAS-7103's Web administration page

from your default browser.

4. [DHCP server not available in the Network] Lanuch Web Browser and key in the

default IP address of the NAS-7103. If there is no DHCP server in the network,

your NAS-7103 will use IP address 192.168.0.20 as its default. Please configure your PC to the same IP subnet as well.

5. As soon as the Web browser start up, NAS-7103 will prompt for User name and Password. Please key in "admin" for both.

6. You may now start to configure your NAS-7103 such as Share Folder, Network Configuration, User Management and so on.

For more about your configuration, please also refer to the CD-ROM manual.

USB HDD