Planet MI-560R User Manual

VOICE FAXMODEM

56V14HCF/2

USER'S MANUAL

Quick Reference Guide to Voice and Fax

For information on the use of the voice or fax functions, please refer to the following schematics.

Internal model

Mic In Jack

The Mic In Jack allows you to connect a microphone for voice input

Speaker Output Jack

The speaker out jack allows you to connect a speaker for audio output from the card’s build-in
power amplifier.

After the hardware installation, the following features of the provided applicatin software are
available:

(1) Send and receive fax, just like a fax machine.
(2) Answer your phone, just like an answering machine.
(3) Send and receive data

For any information regarding the installation or use of the included software, Please refer to the manual
included with the bundled software.

FCC Connection Information

FCC Part 68

This equipment complies with Part 68 of the FCC Rules. On the bottom of this
equipment is a label that contains the FCC Registration Number and Ringer
Equivalence Number (REN) for this equipment. You must provide this information
to the telephone company upon request.

The REN is useful to determine the quantity of devices you may connect to the
telephone line and still have all of those devices ring when your number is called.
In most, but not all areas, the sum of the REN’s of all devices connected to one
line should not exceed five (5.0). To be certain of the number of devices you may
connect to your line, as determined by the REN, you should contact your local
telephone company to determine the maximum REN for your calling area.

If the modem causes harm to the telephone network, the telephone company may
discontinue your service temporarily. If possible, they will notify you in advance.
But if advance notice isn’t practical, you will be notified as soon as possible.
You will be advised of your right to file a complaint with the FCC.

The telephone company may make changes in its facilities, equipment, operations,
or procedures that could affect the proper operation of your equipment. If they
do, you will be notified in advance to give you an opportunity to maintain uninter­rupted telephone service.

If you experience trouble with this modem, please contact your dealer for
repair/warranty information. The telephone company may ask you to disconnect
this equipment from the network until the problem has been corrected or you are
sure that the equipment is not malfunctioning.

This equipment may not be used on coin service provided by the telephone
company. Connection to party lines is subject to state tariffs.

Installation

This device is equipped with a USOC RJ11C connector.

FCC Part 15

The modem generates and uses radio frequency energy. If it is not installed and
used properly in strict accordance with the user’s manual, it may cause interference
with radio and television reception. The modem has been tested and found to
comply with the limits for Class B computing devices in accordance with the
specifications in Subpart B, Part 15 of the FCC regulations. These specifications
are designed to provide reasonable protection against such interference in a
residential installation. However, there is no guarantee that interference will not
occur in a particular installation. FCC regulations require that shielded interface
cables be used with your modem.

If interference does occur, we suggest the following measures be taken to
rectify the problem:

1) Move the receiving antenna.

2) Move the modem away from the radio or TV.

3) Plug the modem into a different electrical outlet.

4) Discuss the problem with a qualified radio/TV technician.

CAUTION : Changes or modifications not expressly approved by the party

responsible for compliance to the FCC Rules could void the
user’s authority to operate this equipment.

Cable connections :

All equipment connected to this modem must use shielded
cable as the interconnection means.

Notes :

Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including

interference that may cause undesired operation.

TABLE OF CONTENTS

Chapter 1 Installation

Chapter 2 Command Line Syntax and Response Codes

Chapter 3 Commands

Chapter 4 Modem,s S-registers

Appendix A Modular Telephone Diagrams

Appendix B ASCII Character Table

Appendix C Jumper J12 Setting For Different PCI Version

Chapter 1 Installation

This manual describes installation of the PCI modem. Set up your modem according
to hardware configuration you get.

Unpacking the modem

The complete package should include:

1) The modem card

2) The user’s manual

3) The modular telephone cable

4) Communication software (optional)

Installing the Modem Card

Installing of the modem card consists of the following steps:

1) Plugging the modem card into the computer.

2) Connecting the modem card to a reliable telephone line.

Plugging the modem card into the computer

After Plugging the modem card into the computer, use the following procedures to
install the modem into the computer.

1) Make sure that the computer is turned off and unplugged from the power
source.

2) Remove the cover of your computer to explore the expansion slots.
(See the computer’s installation guide for instructions).

1-1

3) Choose an expansion slot which is not being used. Use an appropriate screwdrive
to unscrew the screw which holds the metal bracket of the slot. Save the screw as
you will need it later.

4) Remove the metal bracket and set it aside.

5) Hold the modem card by its top edges and align it with the expansion slot. Make
sure that the gold edge connectors (golden fingers) are exactly aligned with the
expansion slot.

CAUTION: Be careful to handle the modem card by its edges only. The precision

components on the card can be easily damaged by static electricity or
physical abuse.

6) Carefully and gently press the card down into the slot. The top of the metal
bracket on the modem should rest exactly on the rear panel bracket of the
computer. If this is not the case, remove the modem card and try again.

7) Secure the modem card with the screw you have previously removed.

INSTALLATION THE DRIVER

A. System Reguirements

- Windows 95, Windows 95 OSR2, Windows 98, Windows NT 4.0,

Windows NT 5.0 operating system.

- Microsoft's PC 97 Design Initiative compliant.

- Unimodem / V compliant.

B. Windows 95/98 Modem Installation

Perform the following procedure to install your modem to your IBM PC or compatible
computer. Different Versions of Windows 95 and Windows 98 may have slightly
different install wizards. The following is the Windows98 installation.

<Step01>First turn off power to PC and remove PC cover, then insert the modem

card to an available PCI slot, close PC cover and turn on power.

<Step02>When Windows 98 loads, it will detect the new hardware and ask for

drivers.

1-2

<Step03>Click

<Step04>Select "Search for the best driver for your device" and click .

1-3

<Step05>Insert the CD that contains the modem installation software.

Select "Specify a location", browse and point the path to
CD-ROM: \Rockwell\DM56HCF\Win9X or CD-ROM: \56HCF or

CD-ROM: \ , then Click

<Step06>Click

1-4

<Step07>Click , and the modem installation will be finished.

1-5

C. Un-installing the 56V14HCF Modem
<Step01>Open the Control Panel from My computer. Double Click

"Add\Remove Programs", Select "Conexant HCF 56K Modem" or
"Rockwell HCF 56K Modem" from the list, then Click

<Step02>Click , then shutdown the computer Remove the modem

hardware from the computer.

1-6

Connecting the modem card to a reliable telephone line

Be sure that the telephone system and line condition are in good working order
before connecting the modem. Test it by lifting the telephone handset and listening for a
clear dial tone.

Next, try placing a couple of call. If the calls cannot go through well or are not loud
and clear, you may have a poor quality telephone line, in which case you had better
find a good telephone line for your modem. Always remember that a highquality
telephone line contributes heavily to reliable data transmission. Also, you will need to
know whether the telephone line uses a tone or pulse dialing system. Check with
the local telephone company for this information.

There are two phone jacks on the side of your modem with the metal bracket.
Two lower jack, which is marked “TO LINE” , should be connected to the wall outlet
of a telephone line. Use the modular telephone cable included with your modem
for this. If modular cable does not fit, consult your dealer to obtain a correct one.

You may wish to connect a telephone set to the upper jack marked “TO PHONE”
so that you can use the phone on the same line, or if you prefer, you may leave the jack
unconnected. It is recommended that you connect the modem to direct outside
telephone line.

Communication Software Configuration

Most popular communications software packages will work well with your modem.

Turn on your computer first, then the modem. Boot the communication software
and check the following parameters:

1) The serial port number.

2) The communication speed and protocol.

3) Data format: data bit, stop bit, parity.

Set the serial port number to COM1, COM2, COM3, or COM4 according to
which your modem is connected. Note that one port should be assigned to only
one device, otherwise, the two devices will conflict with each other.

1-7

Chapter 2 Command Line Syntax and Response Code

The modem responds to commands from the DTE and to activity on the line by
signalling to the DTE in the form of result codes. The result codes that the modem
can send are described below.

Two forms of each result code are available: long-form, an English-like “verbose”
response, and short-form, a data-like numeric response (included in parentheses
following the long-form). The long-form code is preceded and terminated by the
sequence <CR><LF>. The short-from is terminated by <CR>, only with no
preceding sequence.

If result messages are suppressed, nothing is returned to the DTE.

00 - OK
01 - CONNECT
02 - RING
03 - NO CARRIER
04 - ERROR
05 - CONNECT 1200
06 - NO DIALTONE
07 - BUSY
08 - NO ANSWER
09 - CONNECT 600
10 - CONNECT 2400
11 - CONNECT 4800
12 - CONNECT 9600
13 - CONNECT 7200
14 - CONNECT 12000
15 - CONNECT 14400
16 - CONNECT 19200
17 - CONNECT 38400
18 - CONNECT 57600
19 - CONNECT 115200
22 - CONNECT 75TX/1200RX
23 - CONNECT 1200TX/75RX

2-1

40 - CARRIER 300
44 - CARRIER 1200/75
45 - CARRIER 75/1200
46 - CARRIER 1200
47 - CARRIER 2400
48 - CARRIER 4800
49 - CARRIER 7200
50 - CARRIER 9600
51 - CARRIER 12000
52 - CARRIER 14400
53 - CARRIER 16800
54 - CARRIER 19200
55 - CARRIER 21600
56 - CARRIER 24000
57 - CARRIER 26400
58 - CARRIER 28800
59 - CARRIER 31200
60 - CARRIER 33600
66 - COMPRESSION: CLASS 5
67 - COMPRESSION: V.42 bis
69 - COMPRESSION: NONE
70 - PROTOCOL: NONE
77 - PROTOCOL: LAP-M
80 - PROTOCOL: ALT
*150 - CARRIER 32000
*151 - CARRIER 34000
*152 - CARRIER 36000
*153 - CARRIER 38000
*154 - CARRIER 40000
*155 - CARRIER 42000
*156 - CARRIER 44000
*157 - CARRIER 46000
*158 - CARRIER 48000
*159 - CARRIER 50000
*160 - CARRIER 52000
*161 - CARRIER 54000
*162 - CARRIER 56000

2-2

Chapter 3 Commands

The modem will respond to the commands detailed below. Parameters applicable
to each command are listed with the command description. The defaults shown for
each configuration command are those used in the factory profile 0.

Standard “AT” Commands

A/ Re-excute command.
A Go off-hook and attempt to answer a call.

E0 Turn off command echo.
E1 Turn on command echo.

H0 Initiate a hang-up sequence.
H1 If on-hook, go off-hook and enter command mode.

I 0 Report product code.
I 1 Compute and report checksum.
I 2 Compute checksum and report result of comparison to pressured checksum.
I 3 Report firmware revision, model, and interface type.
I 4 Report response programmed by an OEM.
I 5 Report the country code parameter.
I 6 Report modem data pump model and code revision.

L0 Set low speaker volume.
L1 Set low speaker volume.
L2 Set medium speaker volume.
L3 Set high speaker volume.

M0 Turn speaker off.
M1 Turn speaker on during handshaking and turn speaker off while receiving

carrier.

M2 Turn speaker on during handshaking and while receiving carrier.

3-1

M3 Turn speaker off during dialing and receiving carrier and turn speaker on

during answering.

N0 Turn off automode detection.
N1 Turn on automode detection.

O0 Go on-line.
O1 Go on-line and initiate a retrain sequence.

P Force pulse dialing.
Q0 Allow result codes to DTE.

Q1 Inhibit result codes to DTE.
Sn Select S-Register as default.

Sn? Return the value of S-Register n.
=v Set default S-Register to value v.

? Return the value of default S-Register.
T Force DTMF dialing.
V0 Report short form (terse) result codes.

V1 Report long form (verbose) result codes.
W0 Report DTE speed in EC mode.

W1 Report line speed, EC protocol and DTE speed.
W2 Report DCE speed in EC mode.

X0 Report basic call progress result codes, i.e., OK, CONNECT, RING, NO

CARRIER (also, for busy, if enabled, and dial tone detected), NO
ANSWER and ERROR.

X1 Report basic call progress result codes and connections speeds (OK,

CONNECT, RING, NO CARRIER (also, for busy, if enabled, and dial
tone not detected), NO ANSWER, CONNECT XXXX, and ERROR.

X2 Report basic call progress result codes and connections speeds, i.e.,

OK, CONNECT, RING, NO CARRIER (also, for busy, if enabled, and
dial tone not detected), NO ANSWER, CONNECT XXXX, and
ERROR.

X3 Report basic call progress result codes and connection rate, i.e., OK,

CONNECT, RING, NO CARRIER, NO ANSWER, CONNECT XXXX,
BUSY and ERROR.

X4 Report all call progress result codes and connection rate, i.e., OK,

CONNECT, RING, NO CARRIER, NO ANSWER, CONNECT XXXX,
BUSY, NO DIAL TONE and ERROR.

Z Restore stored profile 0 after warm reset.

3-2

&C0 Force RLSD active regardless of the carrier state.
&C1 Allow RLSD to follow the carrier state.

&D0 Interpret DTR ON-to-OFF transition per &Qn:

&Q0, &Q5, &Q6 The modem ignores DTR.
&Q1, &Q4 The modem hangs up.
&Q2, &Q3 The modem hangs up.

&D1 Interpret DTR ON-to-OFF transition per &Qn:

&Q0, &Q1, &Q4, &Q5, &Q6 Asynchronous escape.
&Q2, &Q3 The modem hangs up.

&D2 Interpret DTR On-to-OFF transition per &Qn:

&Q0 thru &Q6 The modem hangs up.
&F0 Restore factory configuration 0.
&G0 Disable guard tone.

&G1 Disable guard tone.
&G2 Enable 1800 Hz guard tone.

&K0 Disable DTE/DCE flow control.
&K1 Enable RTS/CTS DTE/DCE flow control.
&K2 Enable XON/XOFF DTE/DCE flow control.
&K3 Enable both RTS/CTS and XON/XOFF flow control.

&M0 Select direct asynchronous mode.
&P0 Set 10 pps pulse dial with 39% / 61% make/break.

&P1 Set 10 pps pulse dial with 33% / 67% make/break.
&P2 Set 20 pps pulse dial with 39% / 61% make/break.
&P3 Set 20 pps pulse dial with 33% / 67% make/break.

&Q0 Select direct asynchronous mode.
&Q5 Modem negotiates an error corrected link.
&Q6 Select asynchronous operation in normal mode.

&T0 Terminate any test in progress.
&T1 Initiate local analog loopback.

&V Display current configurations.
&W Store the active profile in NVRAM profile 0.
%E0 Disable line quality monitor and auto retrain.

%E1 Enable line quality monitor and auto retrain.
%L Return received line signal level.
%Q Report the line signal quality.

3-3

\N0 Select normal speed buffered mode.
\N2 Select reliable link mode.
\N3 Select auto reliable mode.
\N4 Force LAPM mode.
\N5 Force MNP mode.

3-4

Chapter 4 Modem’s S-registers

Register Function Range / unit Default

S0 Number of Rings to Auto-Answer 0-255 / rings 0

S1 Ring Counter 0-255 / rings 0

S2 Escpae Character 0-255 / decimal 43

S3 Carriage Return Character 0-127 / decimal 13

S4 Line Feed Character 0-127 / decimal 10

S5 Backspace Character 0-32 / ASCII 8

S6 Wait Time for Dial Tone Before Bline 2-255 / seconds 4

Dialing

S7 Wait Timer for Carrier after Dial, for 1-255 / seconds 50

Silence, or for Dial Tone after "W" Dial
Modifier

S8 Pause Time for Dial Delay 0-255 / seconcds 2

S9 Carrier Detect Response Time 1-255 / seconds 6

S10 Lost Carrier to Hang Up Delay 1-255 / seoncds 14

S11 DTMF Tone Duration 50-255/miliseconds 95

S12 Escpae Code Guard Time 0-255 / seoncds 50

S13 Reserved

S14 General Bit Mapped Options 138

4-1

Register Function Range/Unit Default

S15 Reserved

S16 General Bit Mapped Test Options 0

S17 Reserved

S18 Test Timer 0-255 / seconds 0

S19 Reserved

S20 Reserved

S21 V.24/General Bit Mapped Options 52

S22 Speaker/Results Bit Mapped Options 119

S23 General Bit Mapped Options 55

S24 Sleep Inactivity Timer 0-255 / seconds 0

S25 Delay To DTR 0-255 / seconds 5

S26 RTS to CTS Delay 0-255 / seconds 1

S27 Bit Mapped Option 73

S28 Bit Mapped Options 0

S29 Flash Dial Modifier Time 0-255 / ms 70

S30 Disconnect Inactivity Timer 0-255 / seconds 0

S31 Bit Mapped Options 6

S32 XON Character 0-255 / decimal 17

S33 XOFF Character 0-255 / decimal 19

S34-S36 Reserved

4-2

Register Function Range/Unit Default

S37 Desired Line Connection Speed 0

S38 Reserved

S39 Flow Control 3

S40 Reserved

4-3

Appendix

A

Modular Telephone Diagrams

This appendix summaries the modular telephone diagrams, dial pulse and touch­tone specifications.

RJ11 Modular telephone diagram

A-1

Dial pulse specifications

North America Japan Other area
Break Ratio 61% 67% 67%
Break Length 61ms 67ms 67ms
Dial Pulse Length 100ms 200ms 100ms
Dual Pulse Rate 10pps 20pps 10pps
Interdigit Time 789ms 783ms 783ms

Touch-tone Frequencies

1209 1336 1477 1633Hz

697 1 2 3 A

770 4 5 6 B

852 7 8 9 C

941Hz * 0 # D

A-2

Appendix

B

ASCII Character Table

The conversion table below lists the complete set of ASCII characters coded for
digital processing in binary notation (base 2). They are listed below with their
equivalents in decimal notation (base 10) and hexadecimal notation (base 16).

CODE DEC HEX CODE DEC HEX CODE DEC HEX CODE DEC HEX

NUL 0 00 SP 32 20 @ 64 40 , 96 60
CTRL A 1 01 ! 33 21 A 65 41 a 97 61
CTRL B 2 02 “ 34 22 B 66 42 b 98 62
CTRL C 3 03 # 35 23 C 67 43 c 99 63
CTRL D 4 04 $ 36 24 D 68 44 d 100 64
CTRL E 5 05 % 37 25 E 69 45 e 101 65
CTRL F 6 06 & 38 26 F 70 46 f 102 66
CTRL G 7 07 , 39 27 G 71 47 g 103 67
CTRL H 8 08 ( 40 28 H 72 48 h 104 68
CTRL I 9 09 ) 41 29 I 73 49 i 105 69
CTRL J 10 0A 42 2A J 74 4A j 106 6A
CTRL K 11 0B + 43 2B K 75 4B k 107 6B
CTRL L 12 0C , 44 2C L 76 4C l 108 6C
CTRL M 13 0D - 45 2D M 77 4D m 109 6D
CTRL N 14 0E . 46 2E N 78 4E n 110 6E
CTRL O 15 0F / 47 2F O 79 4F o 111 6F
CTRL P 16 10 0 48 30 P 80 50 p 112 70
CTRL Q 17 11 1 49 31 Q 81 51 q 113 71
CTRL R 18 12 2 50 32 R 82 52 r 114 72
CTRL S 19 13 3 51 33 S 83 53 s 115 73
CTRL T 20 14 4 52 34 T 84 54 t 116 74
CTRL U 21 15 5 53 35 U 85 55 u 117 75
CTRL V 22 16 6 54 36 V 86 56 v 118 76
CTRL W 23 17 7 55 37 W 87 57 w 119 77
CTRL X 24 18 8 56 38 X 88 58 x 120 78
CTRL Y 25 19 9 57 39 Y 89 59 y 121 79
CTRL Z 26 1A : 58 3A Z 90 5A z 122 7A
ESC 27 1B ; 59 3B [ 91 5B } 123 7B
FS 28 1C < 60 3C / 92 5C l 124 7C
GS 29 1D = 61 3D ] 93 5D { 125 7D
RS 30 1E > 62 3E A 94 5E ~ 126 7E
US 31 1F ? 63 3F - 95 5F DEL 127 7F

B-1

Appendix

Jumper J12 Setting For Different PCI Version

C

J12

Mainboard
PCI interface Revision 2.1

Mainboard
PCI interface Revision 2.2

Short

Open

C-1

Declaration of CE

This declaration of conformity is according to article 7(3) and article 10(2)

of the Council of European Communities of 3 May 1989.

The protection requirements according the Council Directive article 4

and Annex III are kept.

MODEL / TYPE: Internal Voice / Fax / Modem DM-56V14HCF

This declaration is given from the manufacturer

submitted by

TRAINING RESEARCH CORPORATION

5F,. NO. 571, SEC. 7,

CHUNG HSIAO E. RD., TAIPEI,

TAIWAN, R. O. C.

To the judgement of the products with regard to electromagnetic compatibility

according following regulations:

EN 55 022 Class B

EN 50 082 - 1 (IEC 801 Part 2, 4 / ENV 50140 / ENV 50141)

EN 60950

Declaration of conformity to type

I hereby declare that the product

MODEL/TYPE: Internal Voice / Fax / Modem DM-56V14H

is in conformity with the type as described in EC/German type-examination certificate

- registration no.: A300122K

and satisfies all the technical regulations applicable to the product within the scope of

Council Directives 91/263/EEC and 93/97/EEC:

TBR21

The equipment has been approved to [Commission Decision No. 98/34/EG] for Pan-European
single terminal connection to the Public Switched Telephone Network (PSTN).
However, due to differences between the individual PSTNs provided in different countries the
approval does not, of itself, give an unconditional assurance of successful operation on every
PSTN network termination point. In the event of problems, you should contact your
equipment supplier in the first instance.

CF

PART NO.: 506-10064-06