VOICE FAXMODEM
56V14HSF/5
USER'S MANUAL
Quick Reference Guide to Voice and Fax
For information on the use of the voice or fax functions, please refer to the following schematics.
Internal model
Mic In Jack
The Mic In Jack allows you to connect a microphone for voice input
Speaker Output Jack
The speaker out jack allows you to connect a speaker for audio output from the card’s build-in
power amplifier.
After the hardware installation, the following features of the provided applicatin software are
available:
(1) Send and receive fax, just like a fax machine.
(2) Answer your phone, just like an answering machine.
(3) Send and receive data
For any information regarding the installation or use of the included software, Please refer to the manual
included with the bundled software.
FCC Connection Information
FCC Part 68
This equipment complies with Part 68 of the FCC Rules. On the bottom of this
equipment is a label that contains the FCC Registration Number and Ringer
Equivalence Number (REN) for this equipment. You must provide this information
to the telephone company upon request.
The REN is useful to determine the quantity of devices you may connect to the
telephone line and still have all of those devices ring when your number is called.
In most, but not all areas, the sum of the REN’s of all devices connected to one
line should not exceed five (5.0). To be certain of the number of devices you may
connect to your line, as determined by the REN, you should contact your local
telephone company to determine the maximum REN for your calling area.
If the modem causes harm to the telephone network, the telephone company may
discontinue your service temporarily. If possible, they will notify you in advance.
But if advance notice isn’t practical, you will be notified as soon as possible.
You will be advised of your right to file a complaint with the FCC.
The telephone company may make changes in its facilities, equipment, operations,
or procedures that could affect the proper operation of your equipment. If they
do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service.
If you experience trouble with this modem, please contact your dealer for
repair/warranty information. The telephone company may ask you to disconnect
this equipment from the network until the problem has been corrected or you are
sure that the equipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone
company. Connection to party lines is subject to state tariffs.
Installation
This device is equipped with a USOC RJ11C connector.
FCC Part 15
The modem generates and uses radio frequency energy. If it is not installed and
used properly in strict accordance with the user’s manual, it may cause interference
with radio and television reception. The modem has been tested and found to
comply with the limits for Class B computing devices in accordance with the
specifications in Subpart B, Part 15 of the FCC regulations. These specifications
are designed to provide reasonable protection against such interference in a
residential installation. However, there is no guarantee that interference will not
occur in a particular installation. FCC regulations require that shielded interface
cables be used with your modem.
If interference does occur, we suggest the following measures be taken to
rectify the problem:
1) Move the receiving antenna.
2) Move the modem away from the radio or TV.
3) Plug the modem into a different electrical outlet.
4) Discuss the problem with a qualified radio/TV technician.
CAUTION : Changes or modifications not expressly approved by the party
responsible for compliance to the FCC Rules could void the
user’s authority to operate this equipment.
Cable connections :
All equipment connected to this modem must use shielded
cable as the interconnection means.
Notes :
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including
interference that may cause undesired operation.
Chapter 1 Installation
This manual describes installation of the PCI modem. Set up your modemaccording to
hardware configuration you get.
Unpacking the modem
The complete package should include:
1) The modem card
2) The user’s manual
3) The modular telephone cable
4) Communication software (optional)
Installing the Modem Card
Installing of the modem card consists of the following steps:
1) Plugging the modem card into the computer.
2) Connecting the modem card to a reliable telephone line.
Plugging the modem card into the computer
After Plugging the modem card into the computer, use the following procedures to
install the modem into the computer.
1) Make sure that the computer is turned off and unplugged from the power
source.
2) Remove the cover of your computer to explore the expansion slots.
(See the computer’s installation guide for instructions).
1-1
3) Choose an expansion slot which is not being used. Use an appropriate screwdrive
to unscrew the screw which holds the metal bracket of the slot. Save the screw as
you will need it later.
4) Remove the metal bracket and set it aside.
5) Hold the modem card by its top edges and align it with the expansion slot. Make
sure that the gold edge connectors (golden fingers) are exactly aligned with the
expansion slot.
CAUTION: Be careful to handle the modem card by its edges only. The precision
components on the card can be easily damaged by static electricity or
physical abuse.
6) Carefully and gently press the card down into the slot. The top of the metal
bracket on the modem should rest exactly on the rear panel bracket of the
computer. If this is not the case, remove the modem card and try again.
7) Secure the modem card with the screw you have previously removed.
INSTALLATION THE DRIVER
A. System Reguirements
1.) Recommended CPUs
* Intel Pentium, 150MHz with MMX, 256K Level 2 (L2) cache
* Intel Pentium, 200MHz, 256K L2 cache
* Intel Pentium II
* Intel Pentium Pro
* Intel Celeron (Pentium II, 256MHz, no L2 cache)
* AMD K6, 233MHz, 256K L2 cache
* AMD K6-2, 256K L2 cache
* Cyrix 6x86MX, 266MHz, 256K L2 cache
1-2
2.) Compatible Operating Systems
The modem is compatible with the following operating systems:
* Windows95 (OEM Service Release 2.0 or later)
* Windows98
* Windows NT 4.0 (and later)
* DOS Box under Windows 95/98
3.) System RAM requirements
Windows 95/98 16MB
Windows NT 32MB
B. Windows 95/98 Modem Installation
Perform the following procedure to install your modem to your IBM PC or compatible
computer. Different Versions of Windows 95 and Windows 98 may have slightly
different install wizards. The following is the Windows98 installation.
<Step01>First turn off power to PC and remove PC cover, then insert the modem
card to an available PCI slot, close PC cover and turn on power.
<Step02>When Windows loads, it will detect the new hardware and ask for
drivers.
<Step03>Click
1-3
<Step04>Select "Search for the best driver for your device" and click .
<Step05>Insert the CD that contains the modem installation software.
Select "Specify alocation", browse and point the path to
CD:\Motorola\Sm56DFV, Then Click
1-4
<Step06>Click
<Step07> Click
1-5
<Step08>The modem install program may display a message box that reports "the file
"brazil.hlp" on [Unknown] cannot be found" If this occurs, browse and
re-point the path to the modem installation CD-ROM again. Then Click
<Step09>Click and another device will be found after the modem has
been installed.
1-6
<Step10> Click
<Step11> Select "Search for the best driver for your device", then click
1-7
<Step12>Select "Specify alocation", browse and re-point the path to
CD:\Motorola\Sm56DFV again, Then Click .
<Step13>Click
1-8
<Step14>Click
<Step15>Click and the modem installation will be finished.
1-9
*Important:
Advance Setting:
When the two devices are installed, the control Panel include. "Motorola SM56
Modem" Icon. In this icon, include the following setting:
1.) A prompt for the country of installation. Select a country from the list that
displays. Proper modem operation is guaranteed only if you specify the correct
country. The SM56 software has been designed to with country-specific
characteristics for dial tone, ringback tone, busy tone, and compansion
protocol--µ-Law or A-Law.
2.) A prompt for a language. Select a language from the list that displays.
3.) Microphone and speaker Gain Setting.
Detail USER'S MANUAL
The detail user's manual and AT command, Please refer to the online User's Guide or
open the manual.pdf from CD:\Motorola\ (you have to install "Adobe Acrobat Reader"
from CD:\Msetup.exe)
Connecting the modem card to a reliable telephone line
Be sure that the telephone system and line condition are in good working order
before connecting the modem. Test it by lifting the telephone handset and listening for a
clear dial tone.
Next, try placing a couple of call. If the calls cannot go through well or are not loud
and clear, you may have a poor quality telephone line, in which case you had better
find a good telephone line for your modem. Always remember that a highquality
telephone line contributes heavily to reliable data transmission. Also, you will need to
know whether the telephone line uses a tone or pulse dialing system. Check with
the local telephone company for this information.
There are two phone jacks on the side of your modem with the metal bracket.
Two lower jack, which is marked “TO LINE” , should be connected to the wall outlet
of a telephone line. Use the modular telephone cable included with your modem
for this. If modular cable does not fit, consult your dealer to obtain a correct one.
1-10
You may wish to connect a telephone set to the upper jack marked “TO PHONE”
so that you can use the phone on the same line, or if you prefer, you may leave the jack
unconnected. It is recommended that you connect the modem to direct outside
telephone line.
Communication Software Configuration
Most popular communications software packages will work well with your modem.
Turn on your computer first, then the modem. Boot the communication software
and check the following parameters:
1) The serial port number.
2) The communication speed and protocol.
3) Data format: data bit, stop bit, parity.
Set the serial port number to COM1, COM2, COM3, or COM4 according to
which your modem is connected. Note that one port should be assigned to only
one device, otherwise, the two devices will conflict with each other.
1-11
Chapter 2 Command Line Syntax and Response Code
The modem responds to commands from the DTE and to activity on the line by
signalling to the DTE in the form of result codes. The result codes that the modem
can send are described below.
Two forms of each result code are available: long-form, an English-like “verbose”
response, and short-form, a data-like numeric response (included in parentheses
following the long-form). The long-form code is preceded and terminated by the
sequence <CR><LF>. The short-from is terminated by <CR>, only with no
preceding sequence.
If result messages are suppressed, nothing is returned to the DTE.
00 - OK
01 - CONNECT
02 - RING
03 - NO CARRIER
04 - ERROR
05 - CONNECT 1200
06 - NO DIALTONE
07 - BUSY
08 - NO ANSWER
09 - CONNECT 600
10 - CONNECT 2400
11 - CONNECT 4800
12 - CONNECT 9600
13 - CONNECT 7200
14 - CONNECT 12000
15 - CONNECT 14400
16 - CONNECT 19200
17 - CONNECT 38400
18 - CONNECT 57600
19 - CONNECT 115200
22 - CONNECT 75TX/1200RX
23 - CONNECT 1200TX/75RX
2-1
40 - CARRIER 300
44 - CARRIER 1200/75
45 - CARRIER 75/1200
46 - CARRIER 1200
47 - CARRIER 2400
48 - CARRIER 4800
49 - CARRIER 7200
50 - CARRIER 9600
51 - CARRIER 12000
52 - CARRIER 14400
53 - CARRIER 16800
54 - CARRIER 19200
55 - CARRIER 21600
56 - CARRIER 24000
57 - CARRIER 26400
58 - CARRIER 28800
59 - CARRIER 31200
60 - CARRIER 33600
66 - COMPRESSION: CLASS 5
67 - COMPRESSION: V.42 bis
69 - COMPRESSION: NONE
70 - PROTOCOL: NONE
77 - PROTOCOL: LAP-M
80 - PROTOCOL: ALT
*150 - CARRIER 32000
*151 - CARRIER 34000
*152 - CARRIER 36000
*153 - CARRIER 38000
*154 - CARRIER 40000
*155 - CARRIER 42000
*156 - CARRIER 44000
*157 - CARRIER 46000
*158 - CARRIER 48000
*159 - CARRIER 50000
*160 - CARRIER 52000
*161 - CARRIER 54000
*162 - CARRIER 56000
2-2
Chapter 3 Commands
The modem will respond to the commands detailed below. Parameters applicable
to each command are listed with the command description. The defaults shown for
each configuration command are those used in the factory profile 0.
Standard “AT” Commands
A/ Re-excute command.
A Go off-hook and attempt to answer a call.
E0 Turn off command echo.
E1 Turn on command echo.
H0 Initiate a hang-up sequence.
H1 If on-hook, go off-hook and enter command mode.
I 0 "960"
I 1 "000"
I 2 "OK"
I 3 Software Version
I 4 "OK"
I 5 Disconnect Reason
I 6 Country Code
I7 Product Code
L0 Set low speaker volume.
L1 Set low speaker volume.
L2 Set medium speaker volume.
L3 Set high speaker volume.
M0 Turn speaker off.
M1 Turn speaker on during handshaking and turn speaker off while receiving
carrier.
M2 Turn speaker on during handshaking and while receiving carrier.
3-1
M3 Turn speaker off during dialing and receiving carrier and turn speaker on
during answering.
O0 No Retrain
O1 Retrain
O2 Initiate Rate Renegotiation
O3 Rate Renegotiation with silence
P Force pulse dialing.
Q0 Allow result codes to DTE.
Q1 Inhibit result codes to DTE.
Sn Select S-Register as default.
Sn? Return the value of S-Register n.
=v Set default S-Register to value v.
? Return the value of default S-Register.
T Force DTMF dialing.
V0 Report short form (terse) result codes.
V1 Report long form (verbose) result codes.
X0 Report basic call progress result codes, i.e., OK, CONNECT, RING, NO
CARRIER (also, for busy, if enabled, and dial tone detected), NO
ANSWER and ERROR.
X1 Report basic call progress result codes and connections speeds (OK,
CONNECT, RING, NO CARRIER (also, for busy, if enabled, and dial
tone not detected), NO ANSWER, CONNECT XXXX, and ERROR.
X2 Report basic call progress result codes and connections speeds, i.e.,
OK, CONNECT, RING, NO CARRIER (also, for busy, if enabled, and
dial tone not detected), NO ANSWER, CONNECT XXXX, and
ERROR.
X3 Report basic call progress result codes and connection rate, i.e., OK,
CONNECT, RING, NO CARRIER, NO ANSWER, CONNECT XXXX,
BUSY and ERROR.
X4 Report all call progress result codes and connection rate, i.e., OK,
CONNECT, RING, NO CARRIER, NO ANSWER, CONNECT XXXX,
BUSY, NO DIAL TONE and ERROR.
Z Restore stored profile 0 after warm reset.
&C0 Force RLSD active regardless of the carrier state.
&C1 Allow RLSD to follow the carrier state.
3-2
&D0 Ignore DTR
&D1 Enter Command mode when DTR transitions from asserted to de-asserted.
&D2 Disconnect call when DTR transitions from asserted to de-asserted
&D3 Reset modem parameters to default configuration when DTR transitions
from asserted-to-de-asserted
&F0 Restore factory configuration 0
&G0 Disable guard tone
&G1 Disable guard tone
&G2 Enable 1800 Hz guard tone
&P0 40 / 60 Make / Break Ratio
&P1 33 / 67 Make / Break Ratio
&P2 38 / 62 Make / Break Ratio
&T0 Terminate any test in progress
&T1 Initiate local analog loopback
&V Display current configurations
%L Return received line signal level
\N0 Normal Error - Correction Mode
\N1 Direct Error - Correction Mode
\N4 LAP-M Only
\N6 Reliable
\N7 Auto-Reliable
3-3
Chapter 4 Modem’s S-registers
Register Function Range / unit Default
S0 Number of Rings to Auto-Answer 0-255 / rings 0
S1 Ring Counter 0-255 / rings 0
S2 Escpae Character 0-255 / decimal 43
S3 Carriage Return Character 0-127 / decimal 13
S4 Line Feed Character 0-127 / decimal 10
S5 Backspace Character 0-127 / ASCII 8
S6 Wait Time for Dial Tone Before Bline 2-255 / seconds 4
Dialing
S7 Wait Timer for Carrier after Dial, for 0-255 / seconds 60
Silence, or for Dial Tone after "W" Dial
Modifier
S8 Pause Time for Dial Delay 0-255 / seconcds 2
S10 Lost Carrier to Hang Up Delay 0-255 / seoncds 14
S11 DTMF Tone Duration 60-255/miliseconds 72
S12 Escpae Code Guard Time 0-255 / seoncds 50
S18 Test Timer 0-255 / seconds 0
4-1
Appendix
A
Modular Telephone Diagrams
This appendix summaries the modular telephone diagrams, dial pulse and touchtone specifications.
RJ11 Modular telephone diagram
A-1
Dial pulse specifications
North America Japan Other area
Break Ratio 61% 67% 67%
Break Length 61ms 67ms 67ms
Dial Pulse Length 100ms 200ms 100ms
Dual Pulse Rate 10pps 20pps 10pps
Interdigit Time 789ms 783ms 783ms
Touch-tone Frequencies
1209 1336 1477 1633Hz
697 1 2 3 A
770 4 5 6 B
852 7 8 9 C
941Hz * 0 # D
A-2
Appendix
B
ASCII Character Table
The conversion table below lists the complete set of ASCII characters coded for
digital processing in binary notation (base 2). They are listed below with their
equivalents in decimal notation (base 10) and hexadecimal notation (base 16).
CODE DEC HEX CODE DEC HEX CODE DEC HEX CODE DEC HEX
NUL 0 00 SP 32 20 @ 64 40 , 96 60
CTRL A 1 01 ! 33 21 A 65 41 a 97 61
CTRL B 2 02 “ 34 22 B 66 42 b 98 62
CTRL C 3 03 # 35 23 C 67 43 c 99 63
CTRL D 4 04 $ 36 24 D 68 44 d 100 64
CTRL E 5 05 % 37 25 E 69 45 e 101 65
CTRL F 6 06 & 38 26 F 70 46 f 102 66
CTRL G 7 07 , 39 27 G 71 47 g 103 67
CTRL H 8 08 ( 40 28 H 72 48 h 104 68
CTRL I 9 09 ) 41 29 I 73 49 i 105 69
CTRL J 10 0A 42 2A J 74 4A j 106 6A
CTRL K 11 0B + 43 2B K 75 4B k 107 6B
CTRL L 12 0C , 44 2C L 76 4C l 108 6C
CTRL M 13 0D - 45 2D M 77 4D m 109 6D
CTRL N 14 0E . 46 2E N 78 4E n 110 6E
CTRL O 15 0F / 47 2F O 79 4F o 111 6F
CTRL P 16 10 0 48 30 P 80 50 p 112 70
CTRL Q 17 11 1 49 31 Q 81 51 q 113 71
CTRL R 18 12 2 50 32 R 82 52 r 114 72
CTRL S 19 13 3 51 33 S 83 53 s 115 73
CTRL T 20 14 4 52 34 T 84 54 t 116 74
CTRL U 21 15 5 53 35 U 85 55 u 117 75
CTRL V 22 16 6 54 36 V 86 56 v 118 76
CTRL W 23 17 7 55 37 W 87 57 w 119 77
CTRL X 24 18 8 56 38 X 88 58 x 120 78
CTRL Y 25 19 9 57 39 Y 89 59 y 121 79
CTRL Z 26 1A : 58 3A Z 90 5A z 122 7A
ESC 27 1B ; 59 3B [ 91 5B } 123 7B
FS 28 1C < 60 3C / 92 5C l 124 7C
GS 29 1D = 61 3D ] 93 5D { 125 7D
RS 30 1E > 62 3E A 94 5E ~ 126 7E
US 31 1F ? 63 3F - 95 5F DEL 127 7F
B-1
ATTENTION: Carefully Read This Important Document
BEFORE You Open This Package
SOFTWARE LICENSE AGREEMENT
THE FOLLOWING AGREEMENT IS A LEGAL AGREEMENT BETWEEN YOU
(EITHER AN INDIVIDUAL OR ENTITY), AND MOTOROLA, INC. (FOR ITSELF
AND ITS LICENSORS). THE RIGHT TO USE THIS PRODUCT IS SOLD ONLY
ON THE CONDITION THAT YOU AGREE TO THE FOLLOWING LICENSE.
USING THIS PRODUCT CONSTITUTES ACCEPTANCE OF THE TERMS AND
CONDITIONS SET FORTH IN THIS AGREEMENT.
The enclosed computer program(s) (“Software”) is licensed, not sold, to you by Motorola,
Inc. (“Motorola”) for use only under the terms of this License, and Motorola reserves any
rights not expressly granted to you. You own the disk(s) on which the Software is recorded
or fixed, but Motorola and its licensors retain ownership of the Software itself and its
accompanying written materials, which are protected by the copyright laws
of your country and international treaty provisions.
1. License. This License allows you to use one copy of the Software on a single
computer at a time. To “use” the Software means that the Software is either loaded in the
temporary memory (e.g., RAM) of a computer or installed on the permanent memory of a
computer (e.g., hard disk). Licensee hereby acknowledges that the licenses granted under
this Agreement may be suspended in some cases if Licensee, Licensee’s Customers or End
Users assert an Essential patent for an ITU or prior CITT analog modem
standard against Motorola or a third party.
2. Restrictions. The Software contains trade secrets in a human or machine
perceivable form and, to protect them, you may not REVERSE ENGINEER, DECOMPILE,
DISASSEMBLE OR OTHERWISE REDUCE THE SOFTWARE TO ANY HUMAN
OR MACHINE PERCEIVABLE FORM. YOU MAY NOT MODIFY, ADAPT,
TRANSLATE, RENT, LEASE, LOAN OR CREATE DERIVATIVE WORKS BASED
UPON THE SOFTWARE OR ANY PART THEREOF.
3. Termination. This License is effective until terminated. This License will terminate
immediately without notice form Motorola or judicial resolution if you fail to comply with any
provision of this License. Upon such termination you must destroy the Software, all
accompanying written materials and all copies thereof, and Sections 5, 6, 7 and 8 will survive
any termination.
4. Export Law Assurances. You agree that neither the Software nor any direct
product thereof is being or will be shipped, transferred or re-exported, directly or indirectly,
into any country prohibited by the United States Export Administration Act and the
regulations thereunder or will be used for any purpose prohibited by the Act.
5. Warranty. The Software and written materials are provided “AS IS” and without
warranty of any kind. Motorola’s entire liability and your sole and exclusive remedy for any
breach of the foregoing limited warranty will be, at Motorola’s option, replacement of the
disk(s) or refund the amount paid for this Software License.
NO OTHER WARRANTY IS PROVIDED BY MOTOROLA, AND MOTOROLA
AND ITS LICENSORS EXPRESSLY DISCLAIM ALL OTHER WARRANTIES,
EITHER EXPRESS OF IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. MOTOROLA DOES NOT WARRANT
THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR
ERROR-FREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED.
NO ORAL OR WRITTEN REPRESENTATIONS MADE BY MOTOROLA OR AN
AGENT THEREOF SHALL CREATE A WARRANTY OR IN ANY WAY
INCREASE THE SCOPE OF THIS WARRANTY. BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
IMPLIED WARRANTIES, THE ABOVE LIMITATIONS MAY NOT APPLY TO
YOU.
6. Limitation of Remedies and Damages. Regardless of whether any remedy set forth
herein fails of its essential purpose, in no event shall Motorola or any of the licensors,
directors, officers, employees or affiliates of the foregoing be liable to you for any
consequential, incidental, indirect, special or similar damages whatsoever (including,
without limitation, damages for loss of business profits, business interruption, loss of
business information and the like), whether foreseeable or unforeseeable, arising out of the
use or inability to use the Software or accompanying written materials, regardless of the
basis of the claim and even if Motorola or a Motorola representative has been advised of
the possibility of such damage. Motorola’s liability to you for direct damages for any cause
whatsoever, and regardless of the basis of the form of the action, will be limited to the price
paid for the Software that caused the damages. THIS LIMITATION WILL NOT APPLY
IN CASE OF PERSONAL INJURY ONLY WHERE AND TO THE EXTENT THAT
APPLICABLE LAW REQUIRES SUCH LIABILITY WITHOUT THIS
LIMITATION. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO
YOU.
7. Complete Agreement. This License constitutes the entire agreement between the
parties with respect to the use of the Software and related documentation, and supersedes
all prior or contemporaneous understandings or agreements, written or oral, regarding such
matter. No amendment to or modification of this License will be binding unless in writing
and signed by a duly authorized representative of Motorola.
Declaration of CE
This declaration of conformity is according to article 7(3) and article 10(2)
of the Council of European Communities of 3 May 1989.
The protection requirements according the Council Directive article 4
and Annex III are kept.
MODEL / TYPE: Internal Voice / Fax / Modem DM-56V14HSF
This declaration is given from the manufacturer
submitted by
TRAINING RESEARCH CORPORATION
5F,. NO. 571, SEC. 7,
CHUNG HSIAO E. RD., TAIPEI,
TAIWAN, R. O. C.
To the judgement of the products with regard to electromagnetic compatibility
according following regulations:
EN 55 022 Class B
EN 50 082 - 1 (IEC 801 Part 2, 4 / ENV 50140 / ENV 50141)
EN 60950
Declaration of conformity to type
I hereby declare that the product
MODEL/TYPE: Internal Voice / Fax / Modem DM-56V14HSF
is in conformity with the type as described in EC/German type-examination certificate
- registration no.: A300122K
and satisfies all the technical regulations applicable to the product within the scope of
Council Directives 91/263/EEC and 93/97/EEC:
TBR21
The equipment has been approved to [Commission Decision No. 98/34/EG] for Pan-European
single terminal connection to the Public Switched Telephone Network (PSTN).
However, due to differences between the individual PSTNs provided in different countries the
approval does not, of itself, give an unconditional assurance of successful operation on every
PSTN network termination point. In the event of problems, you should contact your
equipment supplier in the first instance.
PART NO.: 506-10074-00
Loading...