PLANET IKVM-17080 User Manual

IKVM-17080
IKVM-17160

PLANET Technology Corporation

Tel: [phone] Fax: [phone]
Email: [e-mail] www.planet.com.tw

STEP 1 : Mount the LCD to the rack

Screw

CD-ROM KVM Cable

Quick Installation Guide

Power cord

STEP 2 : Install front and rear bracket on
cabinet (Both sides)

STEP 3 : Screw the KVM module into the

console from the back

STEP 4 : Please fix KVM module with the rack mount bracket kit

VERIFY THE CONTENTS INSIDE PACKAGE BOX

The package box should contain the items indicated below plus IKVM-17080 / IKVM-17160. If any item is missing or damaged, please contact the seller

immediately.

Bracket kit

Caution:

1. At least two installers while installing the KVM drawer
device.

2. During the installation, please prevent from the
device falling. It may damage the device or cause
injury of the installer.

STEP 6 : Pull and turn the lock knobs (left and right at the same

time) then put out the screen and open console to operate

STEP 5 : Finish installation as below

Knobs

Unlock

Lock

Knob

STEP 1 : Mount the LCD to the rack

KVM Module

KVM Drawer

Quick GuideQuick Guide

IKVM-17080
IKVM-17160

2011-F00290-000

PLANET Technology Corporation

Tel: [phone] Fax: [phone]
Email: [e-mail] www.planet.com.tw

11F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)

PLANET reserves the right to change specications without prior notice. All brand names and trademarks are property of
their respective owners. Copyright © 2012 PLANET Technology Corp. All rights reserved.

Web Management

OSD (On Screen Display)

Press the “NumLock” on the keyboard twice or simultaneously press the Push Buttons 1 and 2 of the Port Selection Switch on the KVM panel to start the
OSD. Use the Up, Down and Enter keys on the keyboard to switch or directly move the mouse to the target PC, and then double click the left button.

For more about your configuration, please also refer to the CD-ROM manual.

If you have installed the IP-KVM on a network that enables DHCP, you can use the “PSetup” to find out the IP-KVM’s IP.

1. Run "psetup_1.1.0.exe" from the CD.

2. Please click on Refresh button to find your IKVM-17080 / IKVM-17160 in the network. You
can find the MAC address labeled on the bottom side of the IP-KVM module. MAC
address is detected as connection from computer and IP-KVM is valid through USB or
network.

3. [DHCP server available in the Network] Launch Web Browser and key in the IP address of
the IKVM-17080 / IKVM-17160. Please configure your PC to the same IP subnet as well.

4. [DHCP server not available in the Network] Launch Web Browser and key in the default IP
address of the IKVM-17080 / IKVM-17160. If there is no DHCP server in the network,
your IKVM-17080 / IKVM-17160 will use IP address 192.168.0.20 as its default. Please
configure your PC to the same IP subnet as well.

5. As soon as the Web browser starts up, IKVM-17080 / IKVM-17160 will prompt for User
name and Password. Please key in "super" and "pass".

6. You may now start to configure your IKVM-17080 / IKVM-17160 such as Remote Control, Network Configuration, and so on.

PORT 16 PORT 15 PORT 14 PORT 13 PORT 12 PORT 11 PORT 10 PORT 9

PORT 8 PORT 7 PORT 6 PORT 5 PORT 4 PORT 3 PORT 2 PORT 1

100~240V AC 50-60Hz

Switch

PCs PCs

Remote Console

Internet