PLANET FGSW-2624SF User Manual

1. Package Content

Note

2. Requirements

Thank you for purchasing PLANET 24-Port 10/100Mbps + 2 Gigabit TP/SFP Combo Managed Switch, FGSW-2620VM / FGSW-2624SF. Terms of “Switch” in following section of this Quick installation guide means the FGSW-2620VM / FGSW-2624SF.

Upon open the box of the Switch and carefully unpack it. The box should contain the following items:

l The Switch x 1

l This Quick Installation Guide x 1

l User’s manual CD x 1

l Power Cord x 1

l Rubber feet x 4

l Two rack-mounting brackets with attachment screws x1

If any item is found missing or damaged, please contact your local reseller for replacement.

The FGSW-2620VM / FGSW-2624SF provide remote Web interface for manage; the following equipments are necessary for further management.

l Network cables: Use standard network (UTP) cables with RJ45 connectors.

l Subscriber PC installed with Ethernet NIC (Network Card)

l The operate system of subscriber PC that running

Windows 98/ME, NT4.0, 2000/XP, MAC OS9 or later, Linux, UNIX or other platform compatible with TCP/IP protocols.

3. Start Web Management

The PLANET FGSW-2620VM / FGSW-2624SF provide a built-in browser interface. You can manage the Switch remotely by having a remote host with Web browser, such as Microsoft Internet Explorer, Netscape Navigator or Mozilla Firefox.

– 1 – – 2 –

The following shows how to startup the Web Management

of the Switch, please note the Switch is congured through

an Ethernet connection, make sure the manager PC must be set on the same IP subnet address.

For example, the default IP address of the Switch is

192.168.0.100 (the factory-default IP address), then the manager PC should be set at 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.

1. Use Internet Explorer 6.0 or above Web browser, enter IP address http://192.168.0.100 (the factory-default IP address or that you have just changed in console) to access the Web interface.

2. When the following dialog box appears, please enter the default user name "admin" and password “admin”. The login screen in Figure 1 appears.

Default User name: admin Default Password: admin

Figure 1. Web Login Screen of FGSW-2620VM

3. After entering the user name and password, the Web main screen appears as Figure 2.

The following screen based on FGSW-2620VM, for FGSW-2624SF the display will be the same to FGSW-2620VM.

Figure 2. Web Main Screen of FGSW-2620VM

– 3 – – 4 –

Now, you can use the Web management interface to

Note

continue the Switch management, please refer to the user manual for more.

For security reason, please change and memorize the new password after this first setup.

4. While IP Address be changed or

5. Customer Support

Thank you for purchase PLANET products. You can browse

our online FAQ resource at the PLANET Web site rst to

check if it could solve you issue. If you need more support information, please contact PLANET switch support team.

PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php?type=1

forgotten admin password –

To reset the IP address to the default IP Address “192.168.0.100” and the user name / password to factory default mode (default user name and password is admin). Press the hardware reset button at the front panel about 5 seconds. After the device is rebooted, you can login the management Web interface within the same subnet of

192.168.0.xx and default user name / password.

Hardware Reset button

– 5 – – 6 –

Switch support team mail address : support_switch@planet.com.tw

Contents subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.