Planet FGSW-2511P User guide

Download

Page 1

24-Port 10/100TX 802.3at PoE +

1-Port Gigabit TP/SFP Combo Ethernet Switch

FGSW-2511P

User’s Manual

Page 2

Copyright © 2020 by PLANET Technology Corp. All rights reserved. No part of this publication may be re-produced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied,

with respect to the contents hereof and specically disclaims any warranties, merchantability or tness for any particular purpose. Any software described

in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes the entire cost of all nec-essary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

Trademarks

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware will work properly in all environments and applica-tions, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or

tness for a particular purpose.

PLANET has made every eort to ensure that this User’s Manual is accurate;

PLANET disclaims liability for any inaccuracies or omissions that may have

occurred. Information in this User’s Manual is subject to change without notice

and does not represent a commitment on the part of PLANET. PLANET assumes

no respon-sibility for any inaccuracies that may be contained in this User’s Manual.

PLANET makes no commitment to update or keep current the information in this

User’s Manual, and reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s Manual, at any time without notice. If you nd information in this manual that is incorrect, misleading, or incomplete,

we would appreciate your com-ments and suggestions.

Page 3

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-ference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CE Mark Warning

This device is compliant with Class A of CISPR 32. In a residential environment this device may cause radio interference.

WEEE Warning

To avoid the potential eects on the environment and human health as a

result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should

understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted mu-nicipal waste and have to collect such WEEE separately.

Revision

PLANET 24-Port 10/100TX 802.3at PoE + 1-Port Gigabit TP/SFP Ethernet Switch

User's Manual

For Model: FGSW-2511P

Revision: 2.0 (JANUARY 2021)

Part No.: EM-FGSW-2511P_v2.0

Page 4

Table Of Contents

1. Introduction ............................................................................................... 5

1.1 Package Contents ................................................................................ 5

1.2 Product Description .............................................................................. 6

1.3 Features ............................................................................................. 6

1.4 Specications ...................................................................................... 7

2. Hardware Description .................................................................................. 9

2.1 Front Panel ......................................................................................... 9

2.1.1 Multiple Functions of DIP Switch .................................................10

2.1.2 LED Indicators ..........................................................................12

2.2 Rear Panel .........................................................................................12

3. Hardware Installation .................................................................................13

3.1 Rack Mounting ................................................................................... 14

3.2 Desktop Installation ............................................................................ 16

3.3 Grounding the Device ......................................................................... 16

4. Troubleshooting .........................................................................................17

Appendix A - 10/100Mbps, 10/100BASE-TX ......................................................18

Page 5

1. Introduction

1.1 Package Contents

Thank you for purchasing PLANET 24-port 10/100TX 802.3at PoE + 1-port Gigabit

TP/SFP combo Ethernet Switch, FGSW-2511P. Unless specied, “PoE+ Switch” mentioned in this user’s manual refers to the FGSW-2511P.

Open the box of the PoE+ Switch and carefully unpack it. The box should contain

the following items:

FGSW-2511P x 1 User’s Manual x 1

Power Cord x 1 Rubber Feet x 4

Rack-mounting Brackets x 2 Screws x 8

If any of these pieces are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original packing material,

and use them again to repack the product in case there is a need to return it to us for repair.

Page 6

1.2 Product Description

The FGSW-2511P, a new member in the PLANET 802.3at PoE+ Fast Ethernet

Switch family, provides 24 10/100BASE-TX 802.3at Power over Ethernet Plus ports with a total of 190 watts of PoE budget, one 10/100/1000BASE-T uplink port, and one shared 1000BASE-X SFP slot. Its PoE power is more than enough for those

network applications that need Fast Ethernet transmission.

The FGSW-2511P also oers a simple, cost-eective and non-blocking wire-speed

performance. It comes with a compact 19-inch metal housing, suitable for desktop

deployment in enterprise oce or department network application.

The mini-GBIC slot built in the FGSW-2511P supports 1000BASE-SX/LX SFP (small form-factor pluggable) ber-optic modules, meaning the administrator now can exibly choose the suitable SFP transceiver ac-cording to the transmission distance or the transmission speed required to extend the network eciently

1.3 Features

 Physical Interface

z 24 10/100BASE-TX RJ45 copper ports

z 1 10/100/1000BASE-T Gigabit RJ45 copper port

z 1 shared 1000BASE-X SFP interface

z Hardware-based DIP switch for “Standard”, “VLAN”, “QoS” and “Extend” mode

selection

 Power over Ethernet

z Complies with IEEE 802.3at Power over Ethernet Plus end-span PSE

z Up to 24 IEEE 802.3af/at devices powered

z Supports PoE power up to 30 watts for each PoE port

z 190-watt PoE budget

z Each PoE port supports 52V DC power to PoE powered device

z Auto detects powered device (PD)

z Circuit protection prevents power interference between ports

z Remote power feeding up to 100m in standard mode

z The “Extend” mode features 25-watt PoE transmit distance of 250m at speed

of 10Mbps

 Switching

z Hardware-based 10/100Mbps and 10/100/1000Mbps auto-negotiation and

auto MDI/MDI-X

z Flow control for full duplex operation and back pressure for half duplex opera-

tion

Page 7

z Integrates address look-up engine, supporting 16K absolute MAC addresses

z Automatic address learning and address aging

z Solid DIP switch to isolate ports to prevent broadcast storm and defend DHCP

spoong

 Hardware

z 19-inch rack-mount size, 1U height

z LED indicators for PoE ready/activity and LINK/ACT

z Internal AC power supply

z Supports Energy-Ecient Ethernet (EEE) function (IEEE 802.3az)

1.4 Specications

Model FGSW-2511P

Hardware Specications

10/100Mbps Ports 24 10/100BASE-TX MDI/MDI-X RJ45 ports

Gigabit Ports 1 10/100/1000BASE-T MDI/MDI-X RJ45 port

SFP Slot

PoE Inject Port

LED Display

DIP Switch

Switch Architecture Store and Forward

MAC Address Table 16K MAC address table with auto learning function

Switch Fabric 5.8Gbps

Switch Throughput 5.06Mpps @64bytes

Maximum Packet Size 16K bytes

Flow Control

1 1000BASE-X SFP interface, shared with Gigabit RJ45 copper

24-port with 802.3at PoE injector function

(Port-1 to Port-24)

System:

 Power (Green)

10/100BASE-TX RJ45 Interface:

 LNK/ACT (Green, Port-1 to Port-24)  PoE (Amber, Port-1 to Port-24)

10/100/1000BASE-T RJ45 and 1000BASE-X combo Interface:

 LNK/ACT (Green, Port 25)

4 operation modes:

Standard/VLAN/QoS/Extend

Back pressure for half duplex; IEEE 802.3x pause

frame for full duplex

Page 8

Power Requirements AC 100~240V, 3A max.

Power Consumption 205 watts, 699.5 BTU

Dimensions (W x D x H) 440 x 200 x 45 mm

Weight 1220 g

ESD Protection

Surge Immunity ±4KV

Power over Ethernet

PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE

PoE Power Supply Type End-span

Power Pin Assignment 1/2 (+), 3/6(-)

PoE Power Output

PoE Power Budget 190 watts

Number of PDs, 7 watts 24

Number of PDs, 15 watts 12

Number of PDs, 30 watts 6

Standard Conformance

EMI Safety CE, FCC

Standard Compliance

Environment

Operating Environment 0 ~ 50 degrees C

Storage Environment -10 ~ 70 degrees C

Operating Humidity 5 ~ 95%, relative humidity, non-condensing

Storage Humidity 5 ~ 95%, relative humidity, non-condensing

Contact discharge of ±6KV DC Air discharge of ±8KV DC

Per Port 52V DC, 600mA. max. 30 watts (IEEE 802.3at) Per Port 52V DC, 300mA. max. 15.4 watts (IEEE 802.3af)

IEEE 802.3 IEEE 802.3u IEEE 802.3ab IEEE 802.3z IEEE 802.3x IEEE 802.3af IEEE 802.3at IEEE 802.3z

Ethernet Fast Ethernet

Gigabit 1000BASE-T

Gigabit SX/LX Flow Control Power over Ethernet Power over Ethernet Plus

Energy Ecient Ethernet

Page 9

2. Hardware Description

1 3 5 7 9 11 13 17 19 2115 23

This section describes the hardware features of the FGSW-2511P. For easier management and control of the FGSW-2511P, familiarize yourself with its display indicators and ports. Front panel illustrations in this chapter display the unit LED

indicators. Before connecting any network device to the FGSW-2511P, please read

this chapter carefully.

2.1 Front Panel

The front panel of the FGSW-2511P consists of 24 Auto-Sensing 10/100Mbps Ethernet RJ45 Ports, 1 Au-to-Sensing 10/100/1000Mbps Ethernet RJ45 Port and 1 1000 Mbps SFP port. The LED Indicators are also located on the front panel of the

FGSW-2511P.

24-Port 10/100X 802.3at PoE + 1-Port Gigabit TP/SFP Combo Ethernet Switch

FGSW-2511P

ACTLNK

2 4 6 8 10 12 14 18 20 2216 24

PoE-in-Use

1 3 5 7 9 11 13 17 19 2115 23 25

PoE

Figure 2-1: FGSW-2511P Switch Front Panel

2 4 6 8 10 12 14 18 20 2216 24

Extend

VLAN

GigabitPWR

Standard

QoS

10/100/1000T

1000X

Page 10

2.1.1 Multiple Functions of DIP Switch

The front panel of FGSW-2511P provides one DIP switch for Standard, QoS, VLAN and Extend mode se-lections. The detailed descriptions are shown in the

following table.

DIP Switch Mode Function

Extend

VLAN

Standard

QoS

This mode makes the FGSW-2511P operate as a general

switch and all PoE ports operate at 10/100Mbps auto-

negotiation. All ports can communicate with one another.

Note

Extend

VLAN

This mode makes the FGSW-2511P operate as a VLAN isolation switch and

1. Port 1 to port 24 will isolate respectively.

Standard

QoS

Extend

VLAN

2. Port 1 to port 24 can only communicate with port 25 (uplink port)

1. Port 1 to Port 8 supports port priority; optimize port

cache

Standard

QoS

Extend

VLAN

Standard

QoS

2. All ports can communicate with one another.

This mode makes the FGSW-2511P operate as a Long Reach PoE switch and

1. Port 1 to Port 8 support farthest transmission distance of up to 250 meters

2. Port 1 to Port 8 data rate down to 10Mbps

3. All ports can communicate with one another

Please adjust the DIP switch before powering on the FGSW-2511P.

Page 11

Standard Mode (default)

Standard

QoS

Extend

VLAN

Standard

QoS

Extend

VLAN

Standard

QoS

Extend

VLAN

PoE IP Camera

PoE

Power

NVR

FGSW-2511P

100 meters (328 feet)

VLAN Isolation Mode

Port 25 to Ports 1~24 Access Permitted

PoE

IP Camera

PoE

100BASE-TX UTP with PoE

Ports 1 to 24

Access Denied

100BASE-TX UTP with PoE

1000BASE-T UTP

Extend Mode

PoE IP Camera

PoE

Power

FGSW-2511P

Ports 1 to 8

250 meters (820 feet)

PoE

10BASE-T UTP with PoE

Page 12

2.1.2 LED Indicators

System

LED Color Function

PWR Green Lights to indicate that the PoE+ Switch has power.

Per 10/100BASE-TX PoE+ Port

LED Color Function

Lights to indicate the PoE+ Switch is successfully

LNK/ACT Green

connecting to the network at 10/100Mbps. Blinks to indicate that the Switch is actively sending or

receiving data over that port.

PoE-in-use Amber

Lights to indicate the port is providing 52V DC in-line power. (1-24 ports)

10/100/1000BASE-T and 1000BASE-X combo Port

LED Color Function

Lights to indicate the Switch is successfully connecting to

LNK/ACT Green

the network.

Blinks to indicate that the Switch is actively sending or

receiving data over that port.

2.2 Rear Panel

The rear panel of the FGSD-1011HP has an AC inlet power socket, which accepts input power of 100 to 240V AC, 50-60Hz.

100-240V

, 3A max.

Power

Note

Figure 2-2: FGSW-2511P Switch Rear Panel

1. The device is a power-required device which means it will not work till it is powered. If your networks should be active all the

time, please consider using UPS (Uninterrupted Power Supply)

for your device. It will prevent you from network data loss or network downtime.

2. In some areas, installing a surge suppression device may also help to protect your FGSW-2511P from being damaged by unregulated surge or current to the FGSW-2511P.

Page 13

3. Hardware Installation

Start up

Please refer to the following for your cabling:

 10/100BASE-TX

All 10/100BASE-TX ports come with Auto-Negotiation capability. They automatically support 100BASE-TX and 10BASE-T networks. Users only need to plug a working network device into one of the 10/100 BASE-TX ports, and then turn on the FGSW2511P. The port will automatically run at 10Mbps, 20Mbps, 100Mbps or 200Mbps

after negotiating with the connected device.

 10/100/1000BASE-T

The 10/100/1000BASE-T port comes with Auto-Negotiation capability, which automatically supports 1000BASE-T, 100BASE-TX and 10BASE-T networks. Users only need to plug a working network device into the 10/100/1000BASE-T port, and then turn on the PoE+ Switch. The port will automatically run at 10Mbps, 20Mbps, 100Mbps or 200Mbps and 1000Mbps or 2000Mbps after negotiating with the

connected device.

 Cabling

Both 10/100BASE-TX and 10/100/1000BASE-T ports use RJ45 sockets -- similar to the phone jacks -- for connection of unshielded twisted-pair cable (UTP). The IEEE

802.3/802.3u/802.3ab Fast/Gigabit Ethernet standard requires Category 5 UTP for 100Mbps 100BASE-TX. 10BASE-T networks can use Cat.3, 4, 5 or 1000BASE-T uses 5/5e/6 UTP (see table below). Maximum distance is 100 meters (328 feet).

Port Type Cable Type Connector

10BASE-T Cat.3, 4, 5, 2-pair RJ45

100BASE-TX Cat.5, 5e UTP, 4-pair RJ45

1000BASE-T Cat.5/5e/6 UTP, 4-pair RJ45

Any Ethernet devices like hubs/PCs can be connected to the FGSW-2511P by using

straight-through wires. The whole 10/100/1000 Mbps ports are auto-MDI/MDI-X

that can be used on straight-through or crossover cable.

Page 14

3.1 Rack Mounting

To install the FGSW-2511P in a 19-inch standard rack, follow the instructions described below.

Step 1: Place your FGSW-2511P on a hard at surface, with the front panel

positioned towards your front side.

Step 2: Attach a rack-mount bracket to each side of the FGSW-2511P with

supplied screws attached to the package. Figure 3-1 shows how to attach brackets to one side of the FGSW-2511P.

24-Port 10/100X

802.3a t PoE

1-Port Gigabit TP/SFP Combo Ethernet Switch

LNK

ACT

PoE-in-Use

FGSW-2511P

Figure 3-1: Attaching the Brackets to the FGSW-2511P.

You must use the screws supplied with the mounting brackets.

Damage caused to the parts by using incorrect screws would invalidate the warranty.

Step 3: Secure the brackets tightly.

Step 4: Follow the same steps to attach the second bracket to the opposite side.

8 10

14 18

2 4 6

16 24

Extend

PoE

11 13

15 23 25

VLAN

GigabitPWR

Standard

QoS

10 12 14 18 20 2216

11 13 17 19 2115

10/100/1000T

1000X

Page 15

Step 5: After the brackets are attached to the FGSW-2511P, use suitable screws

to securely attach the brackets to the rack, as shown in Figure 3-2.

24-Port 10/100X

802.3a t PoE

1-Port Gigabit TP/SFP Combo Ethernet Switch

LNK

ACT

PoE-in-Use

FGSW-2511P

8 10

14 18

2 4 6 8 10 12 14 18 20 2216

16 24

Extend

PoE

VLAN

11 13

15 23 25

GigabitPWR

Standard

QoS

11 13 17 19

10/100/1000T

1000X

Figure 3-2: Mounting the FGSW-2511P in a Rack

Step 6: Connect your FGSW-2511P to 802.3af/802.3at complied power devices

(PDs) and other network devices.

 Connect one end of a standard network cable to the 10/100BASE-TX RJ45

ports on the front panel of the FGSW-2511P.

 Connect the other end of the cable to the PoE PD devices such as PoE IP

cameras, PoE wireless Access points, PoE VoIP Phones, etc.

Connection to the Switch requires UTP Category 5e, 6 network cabling with RJ45 tips.

Note

Step 7: Supply power to the FGSW-2511P.

 Connect one end of the power cable to the FGSW-2511P.

 Connect the power plug of the power cable to a standard wall outlet.

When the FGSW-2511P receives power, the Power LED should remain solid Green.

Page 16

3.2 Desktop Installation

To install the FGSW-2511P on desktop, simply follow the following steps:

Step 1: Attach the rubber feet to the recessed areas on the bottom of the FGSW-

2511P, as shown in Figure 3-3.

24-Port 10/100X

802. 3a

t PoE

1-Port Gigabit TP/SFP Combo Ethernet Switch

LNK

ACT

PoE-in-Use

FGSW-2511P

Figure 3-3: Attaching the Rubber Feet to the FGSW-2511P

Step 2: Place the FGSW-2511P on desktop near an AC power source.

Step 3: Keep enough ventilation space between the FGSW-2511P and the

surrounding objects.

When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 1, Section 4, under Specifications.

Note

PWR

PoE

7 9

20 2216 24

Extend

1 3 5

12 14 18

16 24

7 9 11 13 17 19

15 23

10/100/1000T

1000X

11 13

VLAN

19 2115 23 25

Gigabit

St andard

QoS

Step 4: Proceed with Steps 6 and 7 of session 3.1 Rack-mount Installation to

connect the network cabling and supply power to your PoE+ Switch.

3.3 Grounding the Device

Uses MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device. EMD (Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY.

Page 17

4. Troubleshooting

This chapter contains information to help you solve issues. If the FGSW-2511P is not functioning properly, make sure the FGSW-2511P was set up according to instructions in this manual.

Q1: The Link LED is not lit.

Solution:

Check the cable connection and also try to swap one new cable.

Q2:100BASE-TXportlinkLED is lit, but the tra󰀩c is irregular.

Solution:

Make sure the attached device is not set to full duplex. Some devices use a

physical or software switch to change duplex modes. Auto-negotiation may not recognize this type of full-duplex setting.

Q3: Why the Switch isn’t connected to the network.

Solution:

Check the LNK/ACT LED on the FGSW-2511P. Try another port on the FGSW-

2511P. Make sure the cable is installed properly. Make sure the cable is the right type. Turn o the power. After a while, turn on the power again.

Q4: Why the FGSW-2511P, connected to PoE device, cannot be

powered on.

Solution:

Please check the cable type of the connection from the FGSW-2511P to the other

end. The cable should be an 8-wire UTP, Category 5e or above and EIA568 cable

within 100 meters. A cable with only 4-wire, short loop or over 100 meters will

aect the power supply.

Please make sure the device is fully complied with IEEE 802.3af/IEEE 802.3at standard.

Q5: What is the power output of each PoE port?

Solution:

1. Each PoE port supports 51-52V DC, 600mA and a maximum of 30 watts of

power output. Detect and inject by the standard of IEEE 802.3at.

2. Each PoE port supports 51-52V DC, 300mA and a maximum of 15.4 watts of

power output. Detect and inject by the standard of IEEE 802.3af.

Page 18

Appendix A - 10/100Mbps, 10/100BASE-TX

When connecting the Switch to another Fast Ethernet switch, a straight-through or

crossover cable might be necessary. Each port of the Switch supports auto-MDI/ MDI-X detection, meaning you can directly connect the Switch to any Ethernet

devices without making a crossover cable. The following table and diagram show

the standard RJ45 receptacle/connector and their pin assignments:

RJ45 Connector Pin Assignment

Contact

1 Tx + (transmit) Rx + (receive)

2 Tx - (transmit) Rx - (receive)

3 Rx + (receive) Tx + (transmit)

4, 5 Not used

6 Rx - (receive) Tx - (transmit)

7, 8 Not used

The standard cable, RJ45 pin assignment

Media Dependent Interface

MDI

Media Dependent Interface-Cross

The standard RJ45 receptacle/connector

MDI-X

Page 19

There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The

following shows the pin allocation and color of straight-through cable and crossover

cable connection:

Straight Cable

12345678

SIDE 1

SIDE 2

SIDE 1

1 = White/Orange 2 = Orange 3 = White/Green 4 = Blue 5 = White/Blue 6 = Green 7 = White/Brown 8 = Brown

SIDE 2

1 = White/Orange 2 = Orange 3 = White/Green 4 = Blue 5 = White/Blue 6 = Green 7 = White/Brown 8 = Brown

Crossover Cable

12345678

SIDE 1

SIDE 2

SIDE 1 SIDE 2

1 = White/Orange 2 = Orange 3 = White/Green 4 = Blue 5 = White/Blue 6 = Green 7 = White/Brown 8 = Brown

1 = White/Green 2 = Green 3 = White/Orange 4 = Blue 5 = White/Blue 6 = Orange 7 = White/Brown 8 = Brown

Figure A-1: Straight-through and Crossover Cable

Please make sure your connected cables are with the same pin assignment and color as the above description before deploying the cables into your network.

Page 20