5
Description
HP-HC series safety hinge switches
Pizzato Elettrica extends its range of products by creating the new HP-HC series safety hinge switches where
safety and style blend into a single product.
The electric switch is fully integrated into the mechanical hinge so that it is virtually invisible to an inexpert
eye. This, asides from being an aesthetic advantage, guarantees greater safety as a switch which is difficult to
identify is consequently even more difficult to tamper with. The rear mounting without screws in sight and the
very precise line mean the switch can be perfectly integrated even with guards of machinery with a very precise
design. The offer is complemented by additional hinges with exclusively mechanical function.
Adjustment of the switching point
The switching point of the
switches can be set with a
Phillips head screwdriver.
Adjusting the switching point
allows for any calibration for
large size guards. After calibrating the switch, it is always necessary to close the hole using
the safety cap supplied.
Integrated M12 connector
Versions with connection from the
top or the bottom are available with
integrated M12 connector.
The use of versions with connectors
permits faster wiring if guards need
to be moved from the test location to
the installation site.
Basic activation angle variants
On request, versions with a switch
activation angle of 15° multiples (e.g.
45° or 90°) are available.
The different activation angle does
not exclude the possibility of adjustment of the switching point by
means of the adjustment screw in
the switch. Any change in the operating angle clearly does not alter the
maximum mechanical switch travel.
Opening angle up to 180°
The mechanical design of the switch also allows use on guards with an
opening angle of up to 180°.
Protection degrees IP67 and IP69K
These devices are designed to be used in
the toughest environmental conditions and
they pass the IP67 immersion test acc. to
EN 60529. They can therefore be used in
all environments where maximum protec-
tion degree of the housing is required. Due
to their special design, these devices are suitable for use in equipment subjected to cleaning with high pressure hot water jets. These
devices meet the IP69K test requirements according to ISO 20653
(water jets with 100 bar and 80°C).
Cable with connector at the back
The version with a rear cable and M12 connector is the best combination between
aesthetics and connection ease.
If machines need to assembled at the customer’s site, this solution allows the wiring
to be hidden. At the same time, it facilitates the connection and disconnection of
the wiring from inside the machinery.
Versions for glass or polycarbonate doors
A version of the switch developed exclusively for glass and polycarbonate doors
without frame is available.
Installation is facilitated by the larger supporting arm and the spaced fixing points;
these also prevent the formation of cracks
caused by holes located too close to the
edge of the guard.
It is necessary to verify that the switch
is not used as a mechanical stop for the
door.
Additional hinges
To complete the installation, various types of additional hinges are
available to be used in a variable
number depending on the weight
of the guard.
These hinges have the same aesthetic but cost less as they contain no electrical parts.
47
General Catalogue Safety 2017-2018
Application examples
OneWay safety
screws
page 310
OneWay safety
screws
page 310
5
•Switch without mounting plate.
•Rear fixing.
•Cable output at the back.
Closed door Open door
•Switch with angular mounting plate
for slotted profile.
•Fastening with internal screws.
•Output with M12 connector at the bottom.
ACCESSORY
Mobile part cover
VF SFH7 page 56
ACCESSORY
OneWay safety screws
p. 310
•Switch with straight mounting plate for front
slotted profile.
•Fastening with screws at the back.
•Cable output at the bottom.
•
•Direct fixing to the polycarbonate plate
•Switch without mounting plate
•Fastening with internal screws
•Output with connector at the back.
General Catalogue Safety 2017-2018
48
5
HP-HC series safety hinge switches
Selection diagram
CABLES AND CONNECTORS
DESIGNS
A B
100x50 mm movable part,
metal
100x75 mm movable part,
metal
CONTACT
BLOCKS
ADDITIONAL HINGES
S A P KSM KAM 0.2PM
Cable output, bottom
(standard)
Cable output, top Cable output, back M12 connector,
bottom
M12 connector,
top
52C 52D 52F 52M 53C 53F 53M
1NO+1NC
slow action
2NC
slow action
1NO+2NC
slow action
2NO+2NC
slow action
1NO+1NC
slow action,
make before
break
1NO+2NC
slow action,
make before
break
2NO+2NC
slow action,
make before
break
50C 50D 50F 50M
1NO+1NC
snap action
2NC
snap action
1NO+2NC
snap action
2NO+2NC
snap action
Cable, length: 0.2 m,
with M12 connector,
at back
49
HC LL
HC AA
HC AB
product option
General Catalogue Safety 2017-2018
Code structure Attention! The feasibility of a code number does not mean the effective availability of a product. Please contact our sales office.
article options
HP AA052C-2SNGH15
5
Movable part
A
100x50 mm movable part, metal
B
100x75 mm movable part, metal
Contact block
52C
1NO+1NC, slow action
52D
2NC, slow action
52F
1NO+2NC, slow action
52M
2NO+2NC, slow action
53C
1NO+1NC, slow action, make before break
53F
1NO+2NC, slow action, make before break
53M
2NO+2NC, slow action, make before break
50C
1NO+1NC, snap action
50D
2NC, snap action
50F
1NO+2NC, snap action
50M
2NO+2NC, snap action
The versions with snap-action contact blocks are
recommended for doors having a radius not greater
than 600 mm.
Connection type
cable, length: 0.2 m with M12
0.2
connector (available for 0.2 PM
versions only)
0.5
cable, length: 0.5 m
…
…………………………….
2
cable, length: 2 m (standard)
…
…………………………….
10
cable, length: 10 m
K
integrated M12 connector
Activation angle
0° activation angle (standard)
H15
15° activation angle
H30
30° activation angle
H45
45° activation angle
H60
60° activation angle
H75
75° activation angle
H90
90° activation angle
Contact type
silver contacts (standard)
silver contacts with 1 µm gold
G
coating
Cable or connector type
N
PVC cable IEC 60332-1 (standard)
G
PVC cable CEI 20-22 II
H
PUR cable, halogen free
R
cable for railway applications (EN 50306-4)
M
M12 connector
Output direction, connections
S
movable part at the right and bottom output
P
movable part at the right and output at the back
A
movable part at the right and output at top
Q
movable part at the left and output at the back
Code structure for additional hinges
General Catalogue Safety 2017-2018
HC AA
HC AA
HC AB
HC LL
Additional hinges (H x L)
100.6 x 49 mm
100.6 x 79 mm
65 x 44.5 mm
50
5
HP-HC series safety hinge switches
Main features
•Metal housing, cable output at top, bottom
or back
•4 types of integrated cable available
•Versions with M12 connector
•Protection degrees IP67 and IP69K
•9 contact blocks with positive opening
•Additional hinges without contacts
Quality marks:
IMQ approval: CA02.03746
UL approval: E131787
CCC approval: 2013010305647255
EAC approval: RUC-IT.AД35.В.00454
If not expressly indicated in this chapter, for correct installation and utilization of all articles see chapter utilization requirements
from page 313 to page 324.
Technical data
Housing
Metal housing, powder-coated
Versions with integrated cable, length 2 m, other lengths from 0.5 … 10 m on request
Versions with integrated M12 connector
Versions with 0.2 m cable length and M12 connector, other lengths from 0.1 … 3 m on
request
Protection degree: IP67 acc. to EN 60529
IP69K acc. to ISO 20653
cables from direct high-pressure and high-
temperature jets)
Corrosion resistance in saline mist: ≥ 300 hours in NSS acc. to ISO 9227
General data
For safety applications up to: SIL 3 acc. to EN 62061
PL e acc. to EN ISO 13849-1
Mechanical interlock, not coded: type 1 acc. to EN ISO 14119
Safety parameters:
: 5,000,000 for NC contacts
B
10D
Service life: 20 years
Ambient temperature for hinges without cable: -25C°…+80C° (standard)
-40C°…+80C° (extended T6)
Ambient temperature for hinges with cable: See table on page 52
Max. actuation frequency: 1200 operating cycles/hour
Mechanical endurance: 1 million operating cycles
Max. actuation speed: 90°/s
Min. actuation speed: 2°/s
Mounting position: any
Max. axial load: 1500 N (HP AA) / 750 N (HP AB)
Max. radial load: 1000 N (HP AA) / 500 N (HP AB)
Tightening torque, M5 screws: 3 … 5 Nm
Electrical data
Rated impulse withstand voltage Uimp: 4 kV
Conditional short circuit current: 1000 A acc. to EN 60947-5-1
Pollution degree: 3
In compliance with standards:
IEC 60947-5-1, EN 60947-5-1, EN 60947-1, IEC 60204-1, EN 60204-1, EN ISO 14119,
EN ISO 12100, IEC 60529, EN 60529, ISO 20653, UL 508, CSA 22.2 No.14.
Approvals:
IEC 60947-5-1, UL 508, CSA 22.2 No.14.
Compliance with the requirements of:
Low Voltage Directive 2014/35/EU, Machinery Directive 2006/42/EC and
EMC Directive 2014/30/EU.
Positive contact opening in conformity with standards:
IEC 60947-5-1, EN 60947-5-1.
(Protect the
Important: Switch off the circuit voltage before disconnecting the connector from the switch. The connector is not suitable for
separation of electrical loads. According to EN 60204-1, versions with 8-pole M12 (2NO+2NC) connector can be used only in PELV
circuits.
Features approved by IMQ
Rated insulation voltage (Ui): 250 Vac
Conventional free air thermal current
(Ith):
Protection against short circuits (fuse): 10 A (1-2 contacts) / 6 A (2-3 contacts) /
Rated impulse withstand voltage (U
Protection degree of the housing: IP67
MA terminals (crimped terminals)
Pollution degree: 3
Utilization category: AC15 / DC13
Operating voltage (Ue): 250 Vac (50 Hz) / 24 Vdc (with connector)
Operating current (Ie): 3 A / 2 A (with connector)
Forms of the contact element: X, Y, X+Y, X+X, Y+Y, Y+Y+X, X+X+Y, X+X+Y+Y
Positive opening contacts on contact blocks 50A, 50C, 50D, 50F, 50G, 50M, 51A,
51C, 51D, 51F, 51G, 51M, 52A, 52C, 52D, 52F, 52G, 52M, 53A, 53C, 53D, 53F,
53G, 53M
In compliance with standards: EN 60947-1, EN 60947-5-1 + A1:2009,
fundamental requirements of the Low Voltage Directive 2014/35/EU.
Please contact our technical department for the list of approved products.
10 A
(1-2 contacts) / 6 A (2-3 contacts) /
4 A (4 contacts or 5-pole M12 connector)
4 A (4 contacts or 5-pole M12 connector) type gG
): 4 kV
imp
(with connector)
51
Features approved by UL
Utilization categories R300 pilot duty (28 VA, 125-250 Vdc)
B300 pilot duty (360 VA, 120-240 Vac) (1-2-3 cont.)
C300 pilot duty (180 VA, 120-240 Vac) (4 cont.)
Housing features type 1, 4X “indoor use only”, 12.
Housing features for the version with 1-2 contacts and type N cable
Type 1, 4X “indoor use only”
In compliance with standard: UL 508, CSA 22.2 No.14
Please contact our technical department for the list of approved products.
General Catalogue Safety 2017-2018
Ambient temperatures for hinges with cable and electrical data
1
2
345
6
7
8
1-2 NC
3-4 NC
5-6 NO
7-8 NO
1
2
345
6
7
8
3-4 NC
5-6 NC
7-8 NO
1
4
1
2
3
5
4 1 2 3
nero
grigio
marrone
blu
giallo-verde
1-2 NC
3-4 NO
5
4
1
2
3
5
4 1 2 3
nero
grigio
marrone
blu
giallo-verde
1-2 NC
3-4 NC
5
1
8
1
4
2
5
4 1 2 3
1-2 NC
3-4 NO
5
4
1
2
3
5
4 1 2 3
1-2 NC
3-4 NC
5
5
Connection type
Contact block 2 contacts 3 contacts 4 contacts 2 contacts 3 or 4 contacts
Cable type
Conductors
Application field
In compliance with
standards
Sheath
Self-extinguishing
Oil resistant
Max. speed
Max. acceleration
Minimum bending radius
Outer diameter
End stripped
Copper conductors
IEC 60228
Cable
,
fixed installation
Cable,
flexible installation
Cable,
mobile installation
Cable,
fixed installation
Cable,
flexible installation
Cable,
extended (-T6) standard
mobile installation
Ambient temperature with cable
5x0.75 mm25x0.75 mm
General General General
05VV-F 05VV-F 05EQ-H EN50306-4
PVC PVC PUR
IEC 60332-1-2
IEC 60332-1-3
80 mm 80 mm 80 mm 60 mm 108 mm 108 mm 94 mm 65 mm 75 mm 90 mm
8 mm 8 mm 8 mm 6 mm 7 mm 7 mm 7 mm 6.5 mm 5 mm 6 mm
80 mm 80 mm 80 mm 80 mm 80 mm 80 mm 80 mm 80 mm / /
Class 5 Class 5 Class 6 Class 5 Class 5 Class 6 Class 5 Class 5 Class 6 Class 6
-25°C +70°C
+5°C +70°C
Thermal current Ith
Rated insulation voltage
Ui
Protection against short
circuits (fuse)
250 Vac
10 A 500 V
type gG
24 V
125 V
DC13
category
Electrical data
Utilization
250 V
24 V
120 V
AC15
category
Utilization
Approvals
250 V
CE cULus
IMQ EAC
N G
IEC 60332-1-2
IEC 60332-1-3
IEC 60332-3
CEI 20-22 II
/ / UL 758 / / UL 758 / / ISO 6722-1 ISO 6722-1
/ / 100 m/min / / 300 m/min / / 50 m/min 50 m/min
/ / 2 m/s
-25°C +70°C
+5°C +70°C
/
/
/
/
10 A
2 A
0.4 A
0.3 A
4 A
4 A
4 A
CCC
/
/
/
/
10 A
250 Vac
10 A 500 V
type gG
2 A
0.4 A
0.3 A
4 A
4 A
4 A
CE
EAC
CCC
H R N H N R
2
5x0.75 mm2 5x0.5mm27x0.5 mm
Mobile installation
HALOGEN
FREE
IEC 60332-1-2
IEC 60332-1-3
2
-25°C +80°C
-25°C +80°C
-25°C +80°C
-40°C +80°C
-40°C +80°C
-40°C +80°C
10 A
250 Vac
10 A 500 V
type gG
2 A
0.4 A
0.3 A
4 A
4 A
4 A
CE cULus
IMQ EAC
CCC
Output with cable
2
7x0.5 mm29x0.34 mm29x0.5 mm
Rail General General
1E-300V5x0.5 mm
MM-90
EN 50306-4
EN 45545
IEC 60332-1
EN 50305
EN 50306-1
03VV-F 03E7Q-H
2
PVC PUR
/
IEC 60332-1-2
IEC 60332-1-3
/ / 25 m/s
-25°C +80°C
-25°C +80°C
-25°C +80°C
-5°C +80°C
/
-40°C +80°C
-40°C +80°C
/
6 A
250 Vac
6 A 500 V
type gG
250 Vac
6 A 500 V
type gG
2 A
0.4 A
0.3 A
0.4 A
0.3 A
4 A
4 A
4 A
CE IMQ
EAC CCC
CE cULus
IMQ EAC
6 A
2 A
4 A
4 A
4 A
CCC
/
/
/
/
Mobile installation
HALOGEN
FREE
IEC 60332-1-2
IEC 60332-1-3
-25°C +80°C
-25°C +80°C
-25°C +80°C
-40°C +80°C
-30°C +80°C
-30°C +80°C
250 Vac
6 A 500 V
type gG
CE cULus
IMQ EAC
6 A
2 A
0.4 A
0.3 A
4 A
4 A
4 A
CCC
General Rail General General
EN50306-4
1P-300V9x0.5 mm
MM-90
EN 50306-4
EN 45545
IEC 60332-1
EN 50305
EN 50306-1
/ / 5 m/s
-25°C +80°C
-25°C +80°C
2
03VV-F
PVC
IEC 60332-1-2
IEC 60332-1-3
-25°C +80°C
-5°C +80°C
/
/
-40°C +80°C
/
-40°C +80°C
/
3 A
250 Vac
3 A 500 V
type gG
2 A
0.4 A
0.3 A
3 A
3 A
3 A
CE cULus
IMQ EAC
CCC
4 A
250 Vac
4 A 500 V
type gG
2 A
0.4 A
0.3 A
4 A
4 A
4 A
CE IMQ
EAC CCC
Output with M12 connector
M12 connector,
5-pole
2
5x0.25 mm2 8x0.25 mm2
03VV-H 03VV-H
2
PVC PVC
/
IEC 60332-3
CEI 20-22 II
-25°C +80°C
-25°C +80°C
/
-15°C +80°C
/
4 A
250 Vac
300 Vdc
4 A 500 V
type gG
2 A
0.4 A
0.3 A
4 A
4 A
4 A
CE cULus
IMQ EAC
CCC
2
/
/
/
M12 connector,
8-pole
IEC 60332-3
CEI 20-22 II
2
5 m/s
-25°C +80°C
-25°C +80°C
-15°C +80°C
/
/
/
2 A
30 Vac
36 Vdc
2 A 500V
type gG
2 A
/
/
2 A
/
/
CE cULus
EAC CCC
Internal cable wiring
2NO+2NC 1NO+2NC 1NO+1NC 2NC
nero
nero-bianco
rosso
rosso-bianco
marrone
blu
viola
viola-bianco
giallo-verde
General Catalogue Safety 2017-2018
nero
nero-bianco
rosso
rosso-bianco
marrone
blu
giallo-verde
Connector pin assignment
2NO+2NC 1NO+2NC 1NO+1NC 2NC
1
3
Female connectors see page 299
2
345
1-2 NC
3-4 NC
5-6 NO
7-8 NO
7
6
2
345
3-4 NC
5-6 NC
7-8 NO
1
7
6
8
52
5
17
30
HP-HC series safety hinge switches
Dimensional drawings
Contact type:
= slow action
L
= slow action
LO
make before
break
Contact block
L
52C
52D
52F
52M
53C
53F
53M
Actuating force
Travel diagrams
HP AA052C-2SN
L
HP AA052D-2SN
L
HP AA052F-2SN
L
HP AA052M-2SN
LO
HP AA053C-2SN
LO
HP AA053F-2SN
LO
HP AA053M-2SN
0.3 Nm (0.65 Nm )
All values in the drawings are in mm
2 m cable, bottom 2 m cable, top 2 m cable, back
30
17
M5
81
71
100.6
27
7
12
22.5
49
page 55 - group 1
M 5
==
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
HP AA052C-2AN
HP AA052D-2AN
HP AA052F-2AN
HP AA052M-2AN
HP AA053C-2AN
HP AA053F-2AN
HP AA053M-2AN
30
M5
M 5
81
71
100.6
27
7
12
22.5
49
0.3 Nm (0.65 Nm )
page 55 - group 1
==
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
81
71
100.6
12
Ø
12
22.5
HP AA052C-2PN
HP AA052D-2PN
HP AA052F-2PN
HP AA052M-2PN
HP AA053C-2PN
HP AA053F-2PN
HP AA053M-2PN
0.3 Nm (0.65 Nm )
page 55 - group 1
17
M 5
27
49
M 5
= =
11.5
7
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
Contact type:
= slow action
L
= slow action
LO
make before
break
Contact block
52C
52D
52F
52M
53C
53F
53M
L
L
L
L
LO
LO
LO
Actuating force
Travel diagrams
M12 connector, bottom M12 connector, top cable (0.2 m) with M12 connector, back
81
71
100.6
10.5
M
12 x1
12
22.5
HP AA052C-KSM
HP AA052D-KSM
HP AA052F-KSM
HP AA052M-KSM
HP AA053C-KSM
HP AA053F-KSM
HP AA053M-KSM
0.3 Nm (0.65 Nm
page 55 - group 1
12 x1
71
27
M5
M5
=
=
17
30
7
49
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
HP AA052C-0.2PM
HP AA052D-0.2PM
HP AA052F-0.2PM
HP AA052M-0.2PM
HP AA053C-0.2PM
HP AA053F-0.2PM
HP AA053M-0.2PM
M12x 1
100.6
31.4
81
22.5
30
17
M
M
5
5
==
71
11.5
27
12
Ø
8.9
12
7
49
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
0.3 Nm (0.65 Nm )
page 55 - group 1
30
17
M5
M 5
==
27
7
49
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
HP AA052C-KAM
HP AA052D-KAM
HP AA052F-KAM
HP AA052M-KAM
HP AA053C-KAM
HP AA053F-KAM
HP AA053M-KAM
)
M
10.5
81
100.6
12
22.5
0.3 Nm (0.65 Nm )
page 55 - group 1
Attention! The safety hinge switch can be combined together exclusively with one or more Pizzato Elettrica hinges (HP or HC series). The use of whichever other
hinge does not guarantee the correct operation of the safety device.
Items with code on green background are stock items
53
Accessories See page 299
The 2D and 3D files are available at www.pizzato.com
General Catalogue Safety 2017-2018
5
Versions for glass or polycarbonate doors - Dimensional drawings
Contact type:
= slow action
L
= slow action
LO
make before
break
Contact block
52C
52D
52F
52M
53C
53F
53M
L
L
L
L
LO
LO
LO
Actuating force
Travel diagrams
HP AB052C-2SN
HP AB052D-2SN
HP AB052F-2SN
HP AB052M-2SN
HP AB053C-2SN
HP AB053F-2SN
HP AB053M-2SN
2 m cable, bottom 2 m cable, top 2 m cable, back
30
17
M5
M 5
81
71
100.6
50
21
12
22.5
79
0.3 Nm (0.65 Nm )
page 55 - group 1
14
==
6.5
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
HP AB052C-2AN
HP AB052D-2AN
HP AB052F-2AN
HP AB052M-2AN
HP AB053C-2AN
HP AB053F-2AN
HP AB053M-2AN
30
17
M5
M 5
81
71
100.6
50
12
22.5
79
0.3 Nm (0.65 Nm )
page 55 - group 1
1421
==
6.5
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
All values in the drawings are in mm
81
71
100.6
12
Ø
8.9
12
22.5
HP AB052C-2PN
HP AB052D-2PN
HP AB052F-2PN
HP AB052M-2PN
HP AB053C-2PN
HP AB053F-2PN
HP AB053M-2PN
0.3 Nm (0.65 Nm )
page 55 - group 1
30
17
M 5
M 5
50
21
79
==
11.5
14
6.5
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
Contact type:
= slow action
L
= slow action
LO
make before
break
Contact block
52C
52D
52F
52M
53C
53F
53M
L
L
L
L
LO
LO
LO
Actuating force
Travel diagrams
M12 connector, bottom M12 connector, top cable (0.2 m) with M12 connector, back
81
71
100.6
M
12 x 1
12
22.5
HP AB052C-KSM
HP AB052D-KSM
HP AB052F-KSM
HP AB052M-KSM
HP AB053C-KSM
HP AB053F-KSM
HP AB053M-KSM
0.3 Nm (0.65 Nm
page 55 - group 1
M
30
17
M 5
M 5
50
21
79
14
==
6.5
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
HP AB052C-KAM
HP AB052D-KAM
HP AB052F-KAM
HP AB052M-KAM
HP AB053C-KAM
HP AB053F-KAM
HP AB053M-KAM
)
12 x 1
10.5
81
71
100.6
12
22.5
0.3 Nm (0.65 Nm )
page 55 - group 1
50
30
17
M5
M 5
17
30
79
1421
==
6.5
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
M12x 1
HP AB052C-0.2PM
HP AB052D-0.2PM
HP AB052F-0.2PM
HP AB052M-0.2PM
HP AB053C-0.2PM
HP AB053F-0.2PM
HP AB053M-0.2PM
81
100.6
8.9
12
22.5
M 5
M5
71
50
12
Ø
79
==
1421
6.5
1NO+1NC
2NC
1NO+2NC
2NO+2NC
1NO+1NC
1NO+2NC
2NO+2NC
0.3 Nm (0.65 Nm )
page 55 - group 1
Attention! The safety hinge switch can be combined together exclusively with one or more Pizzato Elettrica hinges (HP or HC series). The use of whichever other
hinge does not guarantee the correct operation of the safety device.
Accessories See page 299 The 2D and 3D files are available at www.pizzato.com
Items with code on green background are stock items
General Catalogue Safety 2017-2018
54
5
30
HP-HC series safety hinge switches
Additional hinges
17
81
71
100.6
27
12
22.5
49
30
17
M5M5
==
100.6
7
22.5
M 5
M5
81
71
50
12
79
==
35
65
45
1421
12
6.5
22.5
All values in the drawings are in mm
21
M
5
M
5
27
7
44.5
HC AA HC AB HC LL
Travel diagrams All values in the diagrams are in degrees
Contact block
52C
1NO+1NC
52D
2NC
52F
1NO+2NC
52M
2NO+2NC
Group 1
3°5°0
3°0
3°5°0
3°5°0
7°
180°
7°
180°
7°
180°
7°
180°
Contact block
53C
1NO+1NC
53F
1NO+2NC
53M
2NO+2NC
The switching point of the contacts can be adjusted from 0°
to +4° compared to that indicated in the travel diagrams. The
hinge is supplied without pre-adjustment.
Group 1
3°1°0
3°1°0
3°1°0
7°
180°
7°
180°
7°
180°
Contact block
50C
1NO+1NC
50D
2NC
50F
1NO+2NC
50M
2NO+2NC
Group 1
8°
0 4° 180°
1.5°
8°
0 4°
1.5°
0 4°
1.5°
0 4°
1.5°
180°
8°
180°
8°
180°
Accessories
Article Description
VF AC7032
Protection cap of adjustment screw
The cap is supplied with every
hinge and must always be
inserted after the adjustment
of the switching point.
In case of loss or damage, the
cap can be ordered separately.
Max. forces and loads HP AA
Admitted max. loads,
independent of utilization
conditions.
1000 N
max
1500 N
max
25 Nm
max
Legend
F
Force exerted by the weight of the door (N)
max
D Distance from the centre of gravity of the door to the axis of the hinge
(mm)
A Safety hinge
B Additional hinge
Items with code on green background are stock items
Doors with one safety hinge
F
(N)=25,000/D (mm)
max
D
F
max
100 min - 300 max
H/2H/2
A
Doors with one safety hinge
and one additional hinge
F
(N)=200,000/D (mm)
max
H (100 min - 300 max)
F
150 min - 800 max
Accessories See page 299
Legend
Closed contact
Open contact
Positive opening travel
Switch pressed / Switch released
All values in the drawings are in mm
Doors with one safety hinge
and two additional hinges
F
(N)=250,000/D (mm)
max
H/8H/8 H/5H/1.81
A
D
B
A
H/1.66 H/5H/5
max
H (200 min - 1600 max)
D
B
F
max
200 min - 1000 max
The 2D and 3D files are available at www.pizzato.com
H (300 min - 2500 max)
B
55
General Catalogue Safety 2017-2018
5
Max. forces and loads HP AB
Admitted max. loads,
independent of utilization
conditions.
500 N
max
750 N
max
12 Nm
max
Legend
F
Force exerted by the weight of the door (N)
max
D Distance from the centre of gravity of the door to the axis of the hinge
(mm)
A Safety hinge
B Additional hinge
Doors with one safety hinge
F
(N)=12,500/D (mm)
max
D
F
max
100 min - 300 max
Fixing plates
Fastening screws for profile not supplied.
Article Description
VF SFH1-C
Couple of angular plates for HP AA and HC AA supplied
with fastening screws for attachment of the switch
H/2H/2
A
H (100 min - 300 max)
Doors with one safety hinge
and one additional hinge
F
(N)=100,000/D (mm)
max
A
D
F
max
150 min - 800 max
H/1.66 H/5H/5
H (200 min - 1600 max)
B
Article Description
VF SFH2-C
Couple of angular plates for HC LL supplied with
fastening screws for attachment of the switch
All values in the drawings are in mm
Doors with one safety hinge
and two additional hinges
F
(N)=200,000/D (mm)
max
B
A
D
F
max
B
200 min - 1000 max
All values in the drawings are in mm
H/8H/8 H/5H/1.81
H (300 min - 2500 max)
3.5
10
3.5
49
26
Article Description
Couple of plane plates for
VF SFH3-C
HP AA and HC AA supplied
with fastening screws for
attachment of the switch
6.2
45
43.5 43.5
18.51510 18.5 15 10
Article Description
VF SFH4-C
6.2
75
6 max
M6
Couple of plane plates for
HC LL supplied with fastening
screws for attachment of the
switch
43.5
18.51510
6.2
20
3.5
10
3.5
44.5
26
43.5
18.5 15 10
6.2
50
6 max
M6
Article Description
VF SFH7
HP AB series mobile part cover
in stainless steel
170
4
30 38
72
26
Items with code on green background are stock items
6.1 6.1
155
General Catalogue Safety 2017-2018
100.6
95
6 18 6
4
6 26 6
4
30 38
72
26
Accessories See page 299
80
6 18 6
6 26 64
6.16.1
The 2D and 3D files are available at www.pizzato.com
71
= =
2
28
Ø
5.4
56
Loading...