Page 1
IMPORTANT FOR FUTURE REFERENCE
ENGLISH
Please complete this information and retain this manual
for the life of the equipment:
Model #: __________________________
Serial #: __________________________
Date Purchased: ___________________
Installation and Operation Manual
Covering Models
P90, P90K, P90KL
L20-270 Rev.1 (06/11)
Page 2
TO THE PURCHASER, OWNER AND STORE MANAGER
Please review these warnings prior to posting them in a prominent location for reference.
WARNING
DO NOT store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
WARNING
Improper installation, alteration, service or
maintenance can cause property damage, injury or
death. Read the installation, operating and
maintenance instructions thoroughly before installing
or servicing this appliance.
WARNING
Installation, maintenance and repairs should be
performed by a Pitco Authorized Service and Parts
(ASAP) company technician or other qualified
personnel. Installation, maintenance or repairs by
unauthorized and unqualified personnel will void the
warranty.
WARNING
Installation and all connections must be made
according to national and local regulations and codes
in force.
WARNING
A country approved all pole circuit breaker with a
minimum open contact gap of 3mm must be used for
proper installation. (CE countries)
WARNING
During the warranty period if a customer elects to use a
non-original part or modifies an original part purchased
from Pitco and/or its Authorized Service and Parts
(ASAP) companies, this warranty will be void. In
addition, Pitco and its affiliates will not be liable for any
claims, damages or expenses incurred by the customer
which arises directly or indirectly, in whole or in part,
due to the installation of any modified part and/or
received from an unauthorized service center.
WARNING
This appliance, when installed, must be electrically
grounded in accordance with local codes, or in the
absence of local codes, with the National Electrical
Code, ANSI/NFPA 70, or the Canadian Electrical Code,
CSA C22.2, as applicable.
WARNING
DO NOT alter or remove structural material on the
appliance to facilitate storage or for any other reason.
WARNING
This appliance is intended for professional use only
and should be operated by fully trained and qualified
personnel.
WARNING
DO NOT use the electrical cord as a leash to move the
appliance. Series injury and appliance damage can
occur.
WARNING
If the supplied power cord or receptacle is damaged, it
must be replaced by a Pitco Authorized Service and
Parts (ASAP) company technician, or a similarly
qualified person in order to avoid a hazard.
WARNING
The power supply must be disconnected before
servicing, maintaining or cleaning this appliance.
The appliance is NOT jet stream approved. DO NOT
clean the appliance with a water jet.
DO NOT attempt to move this appliance or transfer hot
liquids from one container to another when the unit is
at operating temperature or filled with hot liquids.
Serious personal injury could result if skin comes in
contact with the hot surfaces or liquids.
DO NOT sit or stand on this appliance. The appliance’s
top panel, filter pan, filter carriage, pan cover is not a
step. Serious injury could result from slipping, falling
or contact with hot liquids.
NEVER use the appliance as a step for cleaning or
accessing the ventilation hood. Serious injury could
result from slips, trips or from contacting hot liquids.
The filter pan should be dry and free of water droplets
prior to use. Serious injury could result from hot steam
vapors when hot oil/shortening mixes with water.
DO NOT overfill filter pan with hot oil/shortening. Do
not leave appliance unattended while draining or
refilling with oil/shortening. Over filling the appliance
can cause serious injuries and damage the appliance.
The contents of the crumb catch and/or filter pan of
any filter system must be emptied into a fireproof
container at the end of each day. Some food particles
can spontaneously combust if left soaking in certain
types of oil or shortening.
Completely shut the appliance down when the
oil/shortening is being drained from the appliance. This
will prevent the appliance from heating up during the
draining and filling process. Serious injury and
appliance damage can occur.
This appliance is intended for indoor use only.
DO NOT operate appliance unless all panels and
access covers are attached correctly.
It is recommended that this appliance be inspected by
a qualified service technician for proper performance
and operation on a yearly basis
This appliance is designed to operate on a specific
voltage. This information can be found on the data
plate located on the rear of the appliance
.
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
2
L20-303 Rev 1. (05/11)
Page 3
TABLE OF CONTENTS
ASSEMBLY............................................................................................................................. 3
OPERATION........................................................................................................................... 3
CLEANING.............................................................................................................................. 3
TROUBLESHOOTING............................................................................................................ 4
SCHEMATICS......................................................................................................................... 4
L20-270 Rev.1 (06/11)
2
Page 4
ASSEMBLY
Place the Paper Support Rack inside the
filter envelope so that the threaded
coupling fits into the hole cut in the top of
the paper. Fold the open end of the filter
envelope over two times and push the Clip
over folded end of filter envelope. Thread
the Pick Up Tube onto the threaded
coupling and hand tighten. Insert filter
envelope assembly into filter pan and
connect the Pick Up Tube Union to the
Pump assembly.
Sprinkle filter powder over filter envelope assembly, if desired.
Install Filter Pan Cover onto Filter Pan and Filter Crumb Catch into Filter Pan Cover.
OPERATION
Push the filter unit up to the
fryer to be filtered and plug in
the power cord into the
electrical supply. Screw the
draining adapter into the fryer
drain valve so that the oil can
be drained into the filter.
Adjust location of filter pan so
drain adapter will drain into
Filter Crumb Catch. Turn
fryer off. Carefully open the
drain valve and drain the oil
into the filter pan.
Position Refill Tube outlet
over the fry pot of the fryer.
Press the power switch to the
On position and allow the oil
to return to the fry pot. The
returning oil will wash any
remaining debris from the
bottom of the fry pot. When the fry pot is clear close drain valve and return all of the oil.
After all the oil has been returned to the fry tank the filter will begin to pump air, this will be evident by a
significantly reduced flow from the Refill Tube. Allow filter to pump air for about 15 seconds, press the power
switch to the OFF position. The filtering process is now complete.
To allow oil to drain from refill tube, wait 15 seconds after filtering is completed to move filter.
CLEANING
Disassemble filter pan and remove Filter Pump assembly from filter pan. Clean with a general degreasing
detergent, rinse with fresh water and dry thoroughly. All components that can be removed from the filter unit
may be cleaned in a dish washer. This is generally a good time to install a fresh filter paper in preparation for the
next filtering.
3
L20-270 Rev.1 (06/11)
Page 5
r
TROUBLESHOOTING
Pump does not run Check circuit breaker
Pump does not run, power is present at the
machine, circuit breaker is NOT tripped
Pump is running, but oil is not being pumped Check for blockages in piping and return hose
Air bubbles are present when oil is being
pumped
Check the motor overheat trip switch located
on the end of the moto
There is an air leak on the suction side of the
pump, check filter connections
SCHEMATICS
L20-270 Rev.1 (06/11)
4
Page 6
This page Intentionally left blank
5
L20-270 Rev.1 (06/11)
Page 7
This page intentionally left blank
6 L20-270 R1 (06/11)
L20-329, R2 (05/11)
Page 8
In the event of problems with or questions about
your order, please contact the Pitco Frialator
factory at:
(603) 225-6684 World Wide
MAILING ADDRESS – P.O. BOX 501, CONCORD, NH 03302-0501
SHIPPING ADDRESS – 10 FERRY ST., CONCORD, NH 03301
In the event of problems with or questions about
your equipment please contact the Pitco
Frialator Authorized Service and Parts
Representative (ASAP) covering your area or
contact Pitco at the numbers listed to the left.
L20-270 Rev.1 (06/11)
6
Loading...