Pitco Compact Pasta Control, 60143701 Operation Manual



IMPORTANT FOR FUTURE REFERENCE

IMPORTANT FOR FUTURE REFERENCE

Please complete this information and retain this manual

Please complete this information and retain this manual
for the life of the equipment:

for the life of the equipment:

Model #: __________________________

Model #: __________________________
Serial #: __________________________

Serial #: __________________________
Date Purchased: ___________________

Date Purchased: ___________________

Operations Manual

Covering

Compact Pasta Control

Pitco p/n 60143701

L20-269 Rev 2

(06/11)

Pitco Compact Pasta Control
60143701

Table of Contents

Operation:_______________________________________________________________3

To Turn Control ON: ___________________________________________________________3
To Turn Control OFF: __________________________________________________________3
To Activate timers 1-4: _________________________________________________________3
To Activate timers 5-8: _________________________________________________________3
To Cancel a Cook: _____________________________________________________________3
To Enter Boil Mode:____________________________________________________________3
To Enter Simmer Mode: ________________________________________________________3

Programming:____________________________________________________________4

To Unlock: ___________________________________________________________________4
To Change Simmer Temperature: ________________________________________________4
To Change Timers 1-4: _________________________________________________________4
To Change Timers 5-8: _________________________________________________________4
To Exit Programming: __________________________________________________________5

Other Displays:___________________________________________________________5

Low Vat Temperature __________________________________________________________5
Drain Valve Open______________________________________________________________5
Equipment Fault Displays_______________________________________________________5
To Change Port Address________________________________________________________5
To View Software Revision______________________________________________________5

L20-269 Rev 2

Pg. 2 of 8

Operation:

Pitco Compact Pasta Control

60143701

Warning

Make certain cook tank is filled with water before turning this appliance ON.

To Turn Control ON:

Press the

button. Display will show , , or .

To Turn Control OFF:

Press and hold the

button. Display will show .

To Activate timers 1-4:

Press

, , or .

To Activate timers 5-8:

Press

then , , or .

Note: Multiple timers may run together, but only one timer for a key.

To Cancel a Cook:

Press and hold the timer key until the cook indicator or light above the key is off.

To Enter Boil Mode: Press

until is displayed.

To Enter Simmer Mode: Press

.

until is displayed.

L20-269 Rev 2

Pg. 3 of 8

Pitco Compact Pasta Control
60143701

Programming:

To enter the programming menu, press and hold key for 3 seconds.

The display will show

for program entry or for locked entry.

If control is displaying [Pr--] skip the next step.

To Unlock:

With display showing

, press the key once followed by key. Display will show

. Control is now unlocked ready for programming.

To Change Simmer Temperature:

With display showing

. Press the key, display will show . Press the

to display the current simmer temperature setting as , or . To change this

setting, use the

Display will show

key or key to adjust temperature, then press the key to save value.

. Continue to the next step.

To Change Timers 1-4:

With display showing

, press the key once. Display will show .

Press the timer key needing adjustment. The indictor above that key will illuminate, and the display will
show the current timer setting, for example

time. Press the

key to save value. Display returns to

. Use the key or key to adjust

keys in this group.
When all keys in this group are set, press the

key to continue.

To Change Timers 5-8:

Display will shows

. Press the timer key needing adjustment. The indictor above that key

will illuminate, and the display will show the current timer setting, for example

key or key to adjust time. Press the key to save value. Display returns to

above. Repeat for other timer keys in this group. When all keys in this group are set, press

to continue. Display will show .

above. Repeat for other timer

. Use the

L20-269 Rev 2

Pg. 4 of 8

To Exit Programming:

Pitco Compact Pasta Control

60143701

Press and hold the

key to exit. Display will show or, or, .

Other Displays:

Low Vat Temperature

When tank temperature is below 70°F (21°C), the display will show as
blanks. This is normal for cold start-ups. Heat Demand indicator is located
between the first and second digits of display.

Drain Valve Open

When drain valve is detected open,
normal operations are suspended. The
display will show Drain-Turn-Off message
until reset. To reset, CLOSE the drain
valve, turn the control OFF. Allow the appliance to cool. When the tank is refilled control may be turned
ON. Note: some applications do not use the drain valve input.

Equipment Fault Displays

Probe Faults

If temperature probe faults are detected, the display will show [Prob] and sound the
alarm. All timer functions are disabled, and heat control shut off. To reset, turn
control Off then On.

High Temperature Alarm

This display shows when the control detects a temeprature above the alarm limit of
230°F (110°C). A continuous alarm will sound. To reset, turn control Off then On.

To Change Port Address

With display showing

press

Use

and simultaneously for 2 seconds. Display show the current address setting.

and to change address. Press to save selection and return to

(from section”To Enter Level 2 Programming”),

display. This address setting has no effect on operations of the controller, and, is only meaningful when
control is networked for data collection with other controls. In this case, controls must have different port

addresses. Press and hold the

to exit.

To View Software Revision

While display is showing one of the normal operator displays ([bOIL], [Sim], or [__°F]), press and hold

and the simultaneously for 2 seconds. Display will show a rotating display, 4 digits each,

for 2 seconds each.

“FLSt” ----“1034”----“1 “----“ECL-“----“C*”
“SoFt” ----“2034”----“1 “----“ECL-“----“C*”
“dnLd”----“3034”----“1 “----“ECL-“----“C*”

 Displayed values will vary from those shown in this example, and is dependant on manufacturing

date, and revision of control.

L20-269 Rev 2

Pg. 5 of 8

Pitco Compact Pasta Control
60143701

For Technicians Service instructions refer to Pitco documet L22-271 “Servi ce Manual for Compact Pasta
Control”.

L20-269 Rev 2

Pg. 6 of 8

Pitco Compact Pasta Control

60143701

Notes:

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

________________________________________________________________

L20-269 Rev 2

Pg. 7 of 8

In the event of problems with or questions
about your order, please contact the Pitco

Frialator factory at

[phone] Worldwide.

website address: www.pitco.com

MAILING ADDRESS- P.O. BOX 501, CONCORD, NH 03302-0501

SHIPPING ADDRESS- 10 FERRY ST., CONCORD, NH 03301

In the event of problems with or questions

about your equipment, please contact the

Pitco Frialator Authorized Service and Parts
representative (ASAP) covering your area, or
contact Pitco at the numbers listed to the left.

L20-269 Rev 2 (06/11)