Pioneer HTP-070 User Manual

HOME CINEMA PACKAGE

Operating Instructions

Discover the benefits of registering your product online at http://www.pioneer.co.uk (or http://www.pioneer.eu).

HTP-070

AUDIO/VIDEO MULTI-CHANNEL RECEIVER

VSX-321

-K-P

VENTILATION CAUTION

Anki

IMPORTANT

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

WARNING

Before plugging in for the first time, read the following section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

D3-4-2-1-3_A1_En

D3-4-2-1-4*_A1_En

Operating Environment

Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D3-4-2-1-1_A1_En

D3-4-2-1-7a_A1_En

D3-4-2-1-7c*_A1_En

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.

K041_A1_En

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 20 cm at top, 10 cm at rear, and 10 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

D3-4-2-1-7b*_A1_En

Information for users on collection and disposal of old equipment and used batteries

Symbol for

equipment

Symbol examples

for batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

K058a_A1_En

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal. The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-1a_A1_En

CAUTION

The STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-2a*_A1_En

Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.

Contents

Before you start

Checking what’s in the box . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Flow of settings on the receiver

01 Controls and displays

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Loading the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operating range of remote control . . . . . . . . . . . . . . . . .9

02 Connecting your equipment

Placing the speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Hints on the speaker placement. . . . . . . . . . . . . . . . . . 10

Connecting the speakers. . . . . . . . . . . . . . . . . . . . . . . . . 11

Connect the surround back speakers. . . . . . . . . . . . . . 11

Making cable connections . . . . . . . . . . . . . . . . . . . . . . . 12

HDMI cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

About HDMI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Analog audio cables. . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Digital audio cables . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Video cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

About video outputs connection . . . . . . . . . . . . . . . . . . . 13

Connecting a TV and playback components . . . . . . . . . . 14

Connecting using HDMI . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting your component with no

HDMI terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting a satellite receiver or other digital

set-top box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting other audio components . . . . . . . . . . . . . . . 15

Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Using external antennas . . . . . . . . . . . . . . . . . . . . . . . 16

Plugging in the receiver . . . . . . . . . . . . . . . . . . . . . . . . . 16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

. . . . . . . . . . . . . . 5

03 Basic playback

Canceling the demo display . . . . . . . . . . . . . . . . . . . . . . 17

Playing a source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Selecting the audio input signal . . . . . . . . . . . . . . . . . 17

Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Improving FM sound . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Saving station presets . . . . . . . . . . . . . . . . . . . . . . . . . 19

Listening to station presets . . . . . . . . . . . . . . . . . . . . . 19

Naming preset stations . . . . . . . . . . . . . . . . . . . . . . . . 19

An introduction to RDS . . . . . . . . . . . . . . . . . . . . . . . . . 19

Searching for RDS programs . . . . . . . . . . . . . . . . . . . 20

Displaying RDS information . . . . . . . . . . . . . . . . . . . . 20

Making an audio recording. . . . . . . . . . . . . . . . . . . . . . . 20

04 Listening to your system

Choosing the listening mode . . . . . . . . . . . . . . . . . . . . . 21

Auto playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Listening in surround sound . . . . . . . . . . . . . . . . . . . . 21

Using the Advanced surround . . . . . . . . . . . . . . . . . . 22

Using Stream Direct . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Using the Sound Retriever . . . . . . . . . . . . . . . . . . . . . . . 22

Better sound using Phase Control . . . . . . . . . . . . . . . . . 22

Using surround back channel processing . . . . . . . . . . . 23

Setting the Up Mix function . . . . . . . . . . . . . . . . . . . . . . 23

Setting the Audio options . . . . . . . . . . . . . . . . . . . . . . . . 23

05 The System Setup menu

Using the System Setup menu . . . . . . . . . . . . . . . . . . . . 25

The Speaker Setup menu . . . . . . . . . . . . . . . . . . . . . . . . 25

Speaker Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Crossover Network . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Channel Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Speaker Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

The Auto Power Down menu . . . . . . . . . . . . . . . . . . . . . 26

The FL Demo Mode menu. . . . . . . . . . . . . . . . . . . . . . . . 26

06 ARC (Audio Return Channel) function

ARC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Before starting ARC operation . . . . . . . . . . . . . . . . . . 27

07 Additional information

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Important information regarding the HDMI

connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Resetting the main unit . . . . . . . . . . . . . . . . . . . . . . . . . 29

Cleaning the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Before you start

Checking what’s in the box

Please check that you’ve received the following supplied accessories:

• Remote control

• AAA size IEC R03 dry cell batteries (to confirm system operation) x2

• AM loop antenna

• FM wire antenna

•Power cord

• Warranty card

• Quick start guide

• These operating instructions (CD-ROM)

Installing the receiver

• When installing this unit, make sure to put it on a level and stable surface.

Don’t install it on the following places: – on a color TV (the screen may distort) – near a cassette deck (or close to a device that gives off a

magnetic field). This may interfere with the sound. – in direct sunlight – in damp or wet areas – in extremely hot or cold areas – in places where there is vibration or other movement – in places that are very dusty – in places that have hot fumes or oils (such as a kitchen)

Flow of settings on the receiver

The unit is a full-fledged AV receiver equipped with an abundance of functions and terminals. It can be used easily after following the procedure below to make the connections and settings.

The colors of the steps indicate the following:

Required setting item

Setting to be made as necessary

Connecting the speakers

Where you place the speakers will have a big effect on the sound.

• Placing the speakers (page 10)

• Connecting the speakers (page 11)



Connecting the components

For surround sound, you’ll want to hook up using a digital connection from the Blu-ray Disc/DVD player to the receiver.

• About video outputs connection (page 13)

• Connecting a TV and playback components (page 14)

• Connecting antennas (page 15)

• Plugging in the receiver (page 16)



Power On

Make sure you’ve set the video input on your TV to this receiver. Check the manual that came with the TV if you don’t know how to do this.



The FL Demo Mode menu (page 26)

(When you don’t want the demo display to show on the front panel display.)

Using the Audio Return Channel function (page 27)

(When the connected TV supports the HDMI Audio Return Channel function.)



Playing a source (page 17)

• Selecting the audio input signal (page 17)

• Choosing the listening mode (page 21)



Adjusting the sound as desired

• Using the Sound Retriever (page 22)

• Better sound using Phase Control (page 22)

• Using surround back channel processing (page 23)

• Setting the Up Mix function (page 23)

• Setting the Audio options (page 23)

• The Speaker Setup menu (page 25)

Controls and displays

12 13 14 15 16 14

19 20 21 22 22 2423

Chapter 1:

Controls and displays

Front panel

1 34

275

HDMI

AUDIO/VIDEO MULTI- CHANNEL RECEIVER

VSX

-321

INPUT SELECTOR

STANDBY/ON

SPEAKERS DIMMER DISPLAY BAND TUNER EDIT TUNE PRESET ENTER

PHONES

AUTO SURROUND STREAM DIRECT

STANDARD SURR

8 9 1110

1 INPUT SELECTOR dial

Selects an input source (page 17).

2 Receiver control buttons

SPEAKERS – Use to change the speaker system on or off.

When the SP OFF is selected, no sound is output from the speakers connected to this receiver.

DIMMER – Dims or brightens the display. The brightness can be controlled in four steps.

DISPLAY – Switches the display of this unit. The listening mode, sound volume or input name can be checked by selecting an input source.

3 Character display

See Display on page 7.

4 Tuner control buttons

BAND – Switches between AM, FM ST (stereo) and FM

MONO radio bands (page 18).

ADVANCED

ALC/

SURROUND

SOUND

RETRIEVER

STEREO

TUNER EDIT – Use with TUNE /, PRESET / and ENTER to memorize and name stations for recall

(page 18).

MASTER VOLUME

TUNE / – Used to find radio frequencies (page 18). PRESET / – Use to select preset radio stations

(page 19).

5 Remote sensor

Receives the signals from the remote control (see Operating range of remote control on page 9).

6 HDMI indicator

Blinks when connecting an HDMI-equipped component; lights when the component is connected (page 14).

7 MASTER VOLUME dial

 STANDBY/ON

9 PHONES jack

Use to connect headphones. When the headphones are connected, there is no sound output from the speakers. The listening mode when the sound is heard from the headphone can be selected only from PHONES SURR, STEREO or

STEREO ALC mode.

10 Listening mode buttons

AUTO SURROUND/STREAM DIRECT – Switches

between Auto surround mode (page 21) and Stream Direct playback (page 22).

ALC/STANDARD SURR – Press for standard decoding and to switch between the modes of 2 Pro Logic II, 2 Pro Logic IIx and NEO:6, and the Auto level control stereo mode (page 21).

ADVANCED SURROUND – Switches between the various surround modes (page 22).

STEREO – Press to select stereo playback (page 21).

Controls and displays

11 SOUND RETRIEVER

Press to restore CD quality sound to compressed audio sources (page 22).

Display

12 PHASE

Lights when the Phase Control is switched on (page 22).

13 AUTO

Lights when the Auto Surround feature is switched on (page 21).

14 Tuner indicators

RDS – Lights when an RDS broadcast is received

(page 19). ST – Lights when a stereo FM broadcast is being received

in auto stereo mode (page 18).

TUNE – Lights when a normal broadcast channel. PRESET – Shows when a preset radio station is registered

or called.

MEM – Blinks when a radio station is registered. kHz/MHz – Lights when the character display is showing

the currently received AM/FM broadcast frequency.

15 Speaker indicators

Shows if the speaker system is on or not (page 6).

SPA means the speakers are switched on. SP means the speakers are switched off.

16 Sleep timer indicator

Lights when the receiver is in sleep mode (page 8).

17 PRESET information or input signal indicator

Shows the preset number of the tuner or the input signal type, etc.

18 Character display

Displays various system information.

19 DTS indicators

DTS – Lights when a source with DTS encoded audio

signals is detected. HD – Lights when a source with DTS-EXPRESS or DTS-

HD encoded audio signals is detected.

ES – Lights to indicate DTS-ES decoding.

96/24 – Lights when a source with DTS 96/24 encoded

audio signals is detected. NEO:6 – When one of the NEO:6 modes of the receiver is

on, this lights to indicate NEO:6 processing (page 21).

20 Dolby Digital indicators

2D – Lights when a Dolby Digital encoded signal is detected.

2D+ – Lights when a source with Dolby Digital Plus encoded audio signals is detected.

2HD – Lights when a source with Dolby TrueHD encoded audio signals is detected.

EX – Lights to indicate Dolby Digital EX decoding. 2PLII(x) – Lights to indicate 2 Pro Logic II/2 Pro Logic

IIx decoding (see Listening in surround sound on page 21 for more on this).

21 ADV.S.

Lights when one of the Advanced Surround modes has been selected (see Using the Advanced surround on page 22 for more on this).

22 SIGNAL SELECT indicators

DIGITAL – Lights when a digital audio signal is selected.

Blinks when a digital audio signal is selected and selected audio input is not provided.

HDMI – Lights when an HDMI signal is selected. Blinks when an HDMI signal is selected and selected HDMI input is not provided.

23 Up Mix/DIMMER indicator

Lights when the Up Mix function is set to ON (page 23). Also, lights when DIMMER is set to off.

24 DIR.

Lights when the DIRECT or PURE DIRECT mode is switched on (page 22).

Controls and displays

BD DVD

INPUT SELECT

SOURCESLEEP

CONTROL

DIMMER

INPUT

MIDNIGHT

HDD

RECEIVER

DVR/BDRCDCD-R

ADAPTER

TUNER

PORTABLE

PHASE

SIGNAL SELS.RETRIEVER

BD MENU

ENTER

ADV SURR

AUTO/

DIRECT

VOL

SPEAKERS

LEV

SB CH

DISP

CLR

TEST TONE

DVD

ENTER

CH SELECT

VCR

SHIFT

MUTE

RETURN

AUDIO

PARAMETER

TUNER EDIT

TOOLS

MASTER VOLUME

BAND

HOME MENU

SETUP

PTY SEARCH

TRE

BASS

TOP MENU

RECEIVER

RECEIVER DTV/TV

ALC/

STANDARD

STEREO

3 4

RECEIVER

Remote control

As for operating other devices, the remote control codes for the Pioneer products are preset. The settings cannot be changed.

1 SLEEP

Press to change the amount of time before the receiver switches into standby (30 min – 60 min – 90 min – Off). You can check the remaining sleep time at any time by pressing

SLEEP once.

 RECEIVER

Switches the receiver between standby and on.

RECEIVER

Switches the remote to control the receiver (used to select the white commands above the number buttons (MIDNIGHT, etc)). Also use this button to set up surround sound (page 25) or Audio parameters (page 23).

4 INPUT SELECT

Use to select the input source (page 17).

5 Input function buttons

Use to select the input source to this receiver (page 17). This will enable you to control other Pioneer components with the remote control.

• ADAPTER, PORTABLE button is not used with this

receiver.

6 Receiver control buttons

PHASE – Press to switch on/off Phase Control (page 22). S.RETRIEVER – Press to restore CD quality sound to

compressed audio sources (page 22). SIGNAL SEL – Press to select the audio input signal of the

component to play back (page 17).

7 Listening mode buttons

AUTO/DIRECT – Switches between Auto surround mode

(page 21) and Stream Direct playback (page 22).

STEREO – Press to select stereo playback (page 21). ALC/STANDARD – Press for standard decoding and to

switch between the modes of 2 Pro Logic II, 2 Pro Logic IIx and NEO:6, and the Auto level control stereo mode (page 21).

ADV SURR – Switches between the various surround modes (page 22).

Press BD first to access:

BD MENU* – Displays the disc menu of Blu-ray Discs.

8 System Setup and component control buttons

The following button controls can be accessed after you have selected the corresponding input function button (BD, DVD, etc.).

Press first to access:

AUDIO PARAMETER – Use to access the Audio options (page 23).

SETUP – Press to access the System Setup menu (page 25).

RETURN – Confirm and exit the current menu screen.

Press BD, DVD or DVR/BDR first to access:

TOP MENU – Displays the disc ‘top’ menu of a Blu-ray Disc/DVD.

HOME MENU – Displays the HOME MENU screen. RETURN – Confirm and exit the current menu screen. MENU – Di splay s the T OOLS m enu of Blu -ray D isc pl ayer.

Press TUNER first to access:

TUNER EDIT – Memorizes stations for recall (page 18),

also used to change the name (page 19). BAND – Switches between AM, FM ST (stereo) and FM

MONO radio bands (page 18). PTY SEARCH – Use to search for RDS program types

(page 19).

///

Use the arrow buttons when setting up your surround sound system (page 25). Also used to control Blu-ray Disc/DVD menus/options. Use TUNE / can be used to find radio frequencies and PRESET / can be used to select preset radio stations (page 19).

10 Component control buttons

The main buttons (, , etc.) are used to control a component after you have selected it using the input function buttons.

The controls above these buttons can be accessed after you have selected the corresponding input function button (BD, DVD, DVR/BDR and CD). These buttons also function as described below.

(TUNE

/

, PRESET

/

), ENTER

Controls and displays

CAUTION

30°

7 m

30°

RECEIVER

Press first to access:

BASS –/+, TRE –/+ – Use to adjust Bass or Treble.

• These controls are disabled when the listening mode is

set to DIRECT or PURE DIRECT.

• When the front speaker is set at SMALL in the Speaker

Setting and the Crossover Network is set above 150 Hz, the subwoofer channel level will be adjusted by pressing BASS –/+ (page 25).

11 Number buttons and other component controls

Use the number buttons to directly select a radio frequency (page 18) or the tracks on a CD, etc. There are other buttons that can be accessed after is pressed. (For example MIDNIGHT, etc.)

HDD*, DVD*, VCR* – These buttons switch between the hard disk, DVD and VCR controls for HDD/DVD/VCR recorders.

SB CH – Press to select ON, AUTO or OFF the surround back channel (page 23).

CH SELECT – Press repeatedly to select a channel, then use LEV +/– to adjust the level (page 26).

LEV +/– – Use to adjust the channel level. MIDNIGHT – Switches to Midnight or Loudness listening

(page 23). SPEAKERS – Use to change the speaker system on or off.

When the SP OFF is selected, no sound is output from the speakers connected to this receiver.

DIMMER – Dims or brightens the display. The brightness can be controlled in four steps.

 SOURCE

Turns on or off the power of the Pioneer DVD/DVR units when BD, DVD, DVR/BDR or CD is selected using the input function buttons.

13 TV CONTROL buttons

These buttons can control only be used with Pioneer TVs.

 – Use to turn on/off the power of the TV.

INPUT – Use to select the TV input signal. CH +/– – Use to select channels. VOL +/– – Use to adjust the volume on your TV. DTV/TV* – Switches between the DTV and analog TV

input modes for Pioneer TVs.

RECEIVER

14 MASTER VOLUME +/–

Use to set the listening volume.

15 MUTE

Mutes/unmutes the sound.

16 DISP

Switches the display of this unit. The listening mode, sound volume or input name can be checked by selecting an input source.

17 SHIFT

Press to access the ‘boxed’ commands (above the buttons) on the remote. These buttons are marked with an asterisk (*) in this section.

Loading the batteries

The batteries included with the unit are to check initial operations; they may not last over a long period. We recommend using alkaline batteries that have a longer life.

• Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:

Never use new and old batteries together.

Insert the plus and minus sides of the batteries properly according to the marks in the battery case.

Batteries with the same shape may have different voltages. Do not use different batteries together.

When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.

Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.

WARNING

Store the batteries out of the reach of children and infants. If accidentally swallowed, contact a doctor immediately.

Operating range of remote control

The remote control may not work properly if:

• There are obstacles between the remote control and the receiver’s remote sensor.

• Direct sunlight or fluorescent light is shining onto the remote sensor.

• The receiver is located near a device that is emitting infrared rays.

• The receiver is operated simultaneously with another infrared remote control unit.

Connecting your equipment

CAUTION

Important

5.1 channel surround system:

7.1 channel surround system:

6.1 channel surround system:

Chapter 2:

Connecting your equipment

Placing the speakers

By connecting the left and right front speakers (L/R), the center speaker (C), the left and right surround speakers ( Further, by using an external amplifier, you can connect the left and right surround back speakers (SBL/SBR) to boost your system up to a 7.1 ch surround system.

• You can also connect one surround back speaker (SB) and enjoy a 6.1 ch surround system.

To achieve the best possible surround sound, install your speakers as shown below.

120

SL/SR

), and the subwoofer (SW), a 5.1 ch surround system can be enjoyed.

120

SBL

120

SBR

a. This layout is available only when the additional amplifier is connected to the unit and the

surround back speakers are connected to the amplifier. For details, see Connect the surround back speakers on page 11.

Hints on the speaker placement

Where you put your speakers in the room has a big effect on the quality of the sound. The following guidelines should help you to get the best sound from your system.

• The subwoofer can be placed on the floor. Ideally, the other speakers should be at about ear-level when you’re listening to them. Putting the speakers on the floor (except the subwoofer), or mounting them very high on a wall is not recommended.

• For the best stereo effect, place the front speakers 2 m to 3 m apart, at equal distance from the TV.

• If you’re going to place speakers around your CRT TV, use shielded speakers or place the speakers at a sufficient distance from your CRT TV.

• If you’re using a center speaker, place the front speakers at a wider angle. If not, place

120

them at a narrower angle.

• Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen. Also, make sure the center speaker does not cross the line formed by the leading edge of the front left and right speakers.

• It is best to angle the speakers towards the listening position. The angle depends on the size of the room. Use less of an angle for bigger rooms.

• Surround and surround back speakers should be positioned 60 cm to 90 cm higher than your ears and titled slight downward. Make sure the speakers don’t face each other. For DVD-Audio, the speakers should be more directly behind the listener than for home theater playback.

• If the surround speakers cannot be set directly to the side of the listening position with a

7.1-channel system, the surround effect can be enhanced by turning off the Up Mix function (see Setting the Up Mix function on page 23).

• Try not to place the surround speakers farther away from the listening position than the front and center speakers. Doing so can weaken the surround sound effect.

• Make sure that all speakers are securely installed. This not only improves sound quality, but also reduces the risk of damage or injury resulting from speakers being knocked over or falling in the event of external shocks such as earthquakes.

• To connect the surround back speakers, an additional amplifier is required. Connect the additional amplifier to the SURR BACK PRE OUT outputs of this unit and connect the surround back speakers to the additional amplifier (see Connect the surround back speakers on page 11).

+ 21 hidden pages