Pioneer FH-S500BT, FH-S501BT, FH-S700BT, FH-S701BT Owner's Manual

CD RDS RECEIVER AUTORADIO CD RDS REPRODUCTOR DE CD CON RECEPTOR RDS

FH-S700BS

English Français Español

FH-S701BS

Owner’s Manual

Mode d’emploi

FH-S500BT

Manual de instrucciones

FH-S501BT

Important (Serial number)

The serial number is located on the bottom of this unit. For your own security and convenience, be sure to record this number on the en closed warrant y card.

Important (Numéro de série)

Le numéro de série se trouve au bas de cet appareil. Pour votre sécurité et votre commodité, veillez à noter ce numéro sur la carte de garantie fournie.

Importante (Número de serie)

El número de serie se encuentra en la parte inferior de esta unidad. Por su propia seguridad y comodidad, asegúrese de anotar este número en la tarjeta de garantía que se adjunta.

English

About this manual:

Table of Contents

Before You Start....................................................................................... 4

Getting Started........................................................................................ 6

Radio....................................................................................................... 13

CD/USB/iPhone/AUX............................................................................ 14

Bluetooth............................................................................................... 16

App Mode .............................................................................................. 21

Pandora®................................................................................................ 23

Spotify® .................................................................................................. 24

SiriusXM Satellite Radio...................................................................... 26

Using Pioneer ARC APP....................................................................... 30

Audio Adjustments .............................................................................. 31

Settings .................................................................................................. 33

FUNCTION settings ............................................................................... 33

AUDIO settings ...................................................................................... 36

SYSTEM settings.................................................................................... 38

ILLUMINATION settings........................................................................ 42

MIXTRAX settings.................................................................................. 43

Connections/Installation .................................................................... 45

Additional Information ....................................................................... 51

• In the following instructions, a USB memory or USB audio player are referred to as

“USB device”.

- 2 -

English

• When an iPhone is connected to the unit, the source name on the unit appears as

[iPod]. Pl ease note that this unit supp orts only iPhones (iPhone 5 or later) regardless of the source name (for details, refer to page 58).

- 3 -- 3 -

English

Before You Start

Thank you for purchasing this PIONEER product

To ensure proper use, please read through this manu al before using this product. It i s especially important that you read and observe WAR NI NG s and CAUTIONs in this manual. Please keep the manual in a safe and accessible place for future reference.

FCC ID: EW4C95 MODEL NO.: FH-S700BS/FH-S701BS/FH-S500BT/FH-S501BT IC: 4250A-C95 This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device mu st accept any interference, includ ing interference that may cause un desired operation of this device. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. The Bluetooth ante nna cannot be removed (or replaced) by us er. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).

Alteration o r modifications carr ied out without ap propriate authoriza tion may invalidate the user’s right to operate the equipment.

Note

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

–Consult the dealer or an experienced radio/TV technician for help.

The Safety of Your Ears is in Your Hands

Get the most ou t of your equipment by playing it at a sa fe level—a level that lets the s ound come through clearl y without annoying blaring or distortion and, most impo rtantly, without affectin g your sensitive hearing. So und can be deceiving.

- 4 -

English

Over time, your hearing “comfort level” adapts to higher volumes of sound, so what sounds “normal”

WAR NING

CAUTION

can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

• Set your volume control at a low setting.

• Slowly increase the sound until you can hear it comfortably and clearly, without distortion.

• Once you have established a comfortable sound level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:

• Do not turn up th e volume so high th at you can’t hear what ’s around you.

• Use caution or temporarily discontinue use in potentially hazardous situations.

• Do not use headphones while operating a motorized vehicle; the use of headphones may create a

traffic hazard and is illegal in many areas.

• Do not attempt to install or service this product by yourself. Installation or servicing of this product by persons with out training and experience in electro nic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards.

• Do not attempt to operate the unit while driving. Make sure to pull off the road and park your vehicle

in a safe location before attempting to use the controls on the device.

CAUTION: USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WIL L INCREASE EYE HAZARD.

• Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock could result.

Also, damage to this unit, smoke, and overheating could result from contact with liquids.

• Always keep the volume low enough to hear outside sounds.

• This product is evaluated in moderate and tropical climate condition under the Audio, video and

similar electronic apparatus - Safety requirements, IEC 60065.

CAUTION

This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007.

After-sales service for Pioneer products

Please contac t the dealer, distributor from where you purchas ed this unit or the a uthorized PIONEER Service Station for after-sales service or any other information. In case the necessar y information is not available, please contact the companies listed below: Please do not ship your unit to the companies at the addresses listed below for repair without contacting them in advance.

- 5 -- 5 -

English

U.S.A. and CANADA

Display window

M.C. (multi-control) dial

BAND/

DISP (display)

SRC (source)/OFF

USB port

(eject)

AUX input jack (3.5 mm stereo jack)

Disc loading slot

Pioneer Electronics (USA) Inc. CUSTOMER SUPPORT DIVISION P.O. Box 1760 Long Beach, CA 90801-1760 800-421-1404

For warranty information please see the Limited Warranty sheet included with this unit.

Getting Started

Basic operation

FH-S700BS/S701BS

- 6 -

English

FH-S500BT/S501BT

Display window

M.C. (multi-control) dial

BAND/

DISP (display)

SRC (source)/OFF

USB port

(eject)

AUX input jack (3.5 mm stereo jack)

Disc loading slot

SRC (source)

VOLUME +/– MUTE

DISP (display)

Remote Control

Frequently used operations

The available buttons vary depending on the unit.

- 7 -- 7 -

English

Purpose

Turn on the power* Press SRC/OFF to turn on

Adjust the volume Turn the M.C. dial. Press VOLUME + or –.

Select a source Press SRC/OFF repeatedly. Press SRC repeatedly. Change the display

information Return to th e previous

display/list Return to the normal display

from the menu Change the display

brightness (not available when [SIRIUSXM] is selec ted as a source)

Answering a call Press . Press . Ending a call Press . Press .

* When this unit ’s blue/white lead is connected to th e vehicle’s auto-antenna re lay control terminal,

the vehicle’s antenn a extends when this unit’s source is turned on. To retract the antenna , turn the source off.

Head Unit Remote Control

the power. Press and hold SRC/OFF to turn off the power.

Press DISP repeatedly. Press DISP repeatedly.

Press BAND/ . Press / to select the

Press and hold BAN D/ .

Operation

Press SRC to turn on the power. Press and hold SRC to turn off the power.

Press MUTE to mute the unit. Press MUTE again or press VOLUME + or – to unmute.

next/previous folder.

–

Display indication

The indication varies depending on the unit.

Indication Description

Appears when a lower tier of the menu or folder exists.

Appears when a Bluetooth telephone is connected to this unit by HFP (Hands Free Profile) (page 16) and flashes while the telephone is on hold.

Appears when a Bluetooth audio player is connected to this unit by A2DP (Advanced Audio Distribution Profile) (page 16).

Appears when the button is pressed. Appears when the sound retriever function is set (page 34).

- 8 -

English

Indication Description

RESET button

BASS Appears when [HI]/[LOW] is selected in [D.BASS] (page 38).

Appears when random/shuffle play is set (except when BT AUDIO is selected as the source).

Appears when repeat play is set (except when BT AUDIO is selected as the source).

Appears when a Bluetooth connection is made (page 16).

Resetting the microprocessor

The microprocessor must be reset in the following situations:

– Before using this unit for the first time after installation – If the unit fails to operate properly – When strange or incorrect messages appear on the display

1 Press the RESET button with a pen tip or other pointed instrument.

Preparing the remote control

Remove the insulation sheet before use.

- 9 -- 9 -

English

WAR NIN G

• Do not ingest the battery, Chemical Burn Hazard.

CAUTION

Important

How to replace the battery

Insert the CR2025 (3 V) battery with the plus (+) and minus (–) poles orientated properly.

(The remote con trol supplied with) This product contains a coi n/button cell battery. If the coin/ button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

• Do not expose the battery or remote control to excessive heat such as direct sunlight or fire.

• There is a potential danger of explosion if the batter y is incorrectly replaced. When replacing the

battery, repla ce it with the same type.

• Do not handle or store the battery with metallic tools or objects.

• If the battery leaks, remove the battery and wipe the remote control completely clean. Then install a

new battery.

• When disposing of used batteries, please comply with governmental regulations or environmental

public institutions’ rules that apply in your country/area.

• “Perchlorate Material - special handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate. (Applicable to California, U.S.A.)”

• Do not store the remote control in high temperatures or direct sunlight.

• Do not let the remote control fall onto the floor, where it may become jammed under the brake or

accelerat or pedal.

Setup menu

When you turn the ignition switch to ON af ter installation, the setup menu appears in the display.

- 10 -

English

WAR NIN G

(Only for FH-S700BS/S70 1BS)

NOTE

Do not use the unit in standard mode when a speaker system for network mode is connected to the unit. Do not use the unit in network mode when a speaker system for standard mode is connected to the unit. Thi s may cause damage to the speakers.

1 Turn the M.C. dial to select the options, then press to confirm.

To proceed to the next menu option, you need to confirm your selection.

Menu Item Description LANGUAGE Select the language to display the text information from a

[ENG](English), [ESP](Spanish), [FRA] (Canadian French )

CLOCK SET Set the clock.

SPEAKER MODE (O nly

for FH-S700BS/S701BS)

[STANDARD], [NETWORK]

compressed audio file.

1 Turn t he M.C. dial to adjust th e hour, then press to confirm.

The indicator moves to the minute setting automatically.

2 Turn t he M.C. dial to adjust the minute, then press to confirm. Switch between two operation modes: the 2-way network mode

(NETWORK) and the standard mode (STANDARD) according to the connections you have established. For details on operation modes, see page 32. After selecting the appropriate mode, turn the M.C. dial to select [YES], then press to confirm.

• You cannot complete the setup menu without setting the

[SPEAKER MODE].

• Once the speaker mode is set, this setting cannot be changed

unless the default settings of this product are restored. Restore the default settings to change the speaker mode setting (refer to SYSTEM RESET on page 13).

• When [NETWORK] is selected, the beep tone function is not

availa ble.

2 [QUIT :YES] appears when all the settings have been made.

To return to the first item of the setup menu, turn the M.C. dial to select [QUIT :NO], then press to confirm.

3 Press the M.C. dial to confirm the settings.

These settings other than [SPEAKER MODE] can be made at any time from the SYSTEM settings (page 38).

- 11 -- 11 -

English

NOTE

Canceling the demonstration display (DEMO OFF)

1 Press the M.C. dial to display the main menu. 2 Turn the M.C. dial to select [SYSTEM], then press to confirm. 3 Turn the M.C. dial to select [DEMO OFF], then press to confirm. 4 Turn the M.C. dial to select [YES], then press to confirm.

INITIAL settings

1 Press and hold SRC/OFF until the unit turns off. 2 Press the M.C. dial to display the main menu. 3 Turn the M.C. dial to select [INITIAL], then press to confirm. 4 Turn the M.C. dial to select an option, then press to confirm.

The options var y depending on the unit.

Menu Item Description REAR-SP Select when there is a full-range speaker connected to the rear

[FUL] [SW] Select when there is a subwoofer connected directly to the rear

SP-P/O MODE Select when there is a full-range speaker connected to the rear

[REAR/SUB.W]

[SUB.W/SUB.W] Select when there is a passive subwoofer connected directly to

[REAR/REAR] Select when there are full-range speakers connected to the rear

SYSTEM UPDATE Select [SYSTEM INFO] to confirm the latest system information

[SYSTEM INFO], [S/ W UPDATE]

speaker output leads.

speaker output leads without any auxiliary amplifier.

speaker output leads and there is a subwoofer connected to the RCA output.

the rear speaker output leads and there is a subwoofer connected to the RCA output.

speaker output leads and RCA output. If there is a full-range speaker connected to the rear speaker output leads, and the RCA output is not used, you may select either [REAR/SUB.W] or [REAR/REAR].

on the unit. Select [S/W UPDATE] to update the unit to the latest software and initialize the unit settings. For details on the latest software and updating, visit our website.

- 12 -

English

NOTE

TIP

Menu Item Description SXM RESET Select to initialize the SiriusXM settings.

[YES], [NO]

SYSTEM RESET Select [YES] to initialize the unit settings. The unit will be

[YES], [NO]

restarted automatically.

Radio

The tuner frequencies on this unit are allocated for use in North America. Use in other areas may result in poor reception.

Receiving preset stations

1 Press SRC/OFF to select [RADIO]. 2 Press BAND/ to select the band from [FM1], [FM2], [FM3] or [AM]. 3 Press a number button (1/ to 6/).

You can select a preset channel by pressing and turning the M.C. dial.

The / buttons can be also used to select a preset station when [SEEK] is set to [PCH] in the FUNCTION settings (page34).

Best stations memory (BSM)

The six strongest stations are stored on the number buttons (1/ to 6/).

1 After selecting the band, press the M.C. dial to display the main menu. 2 Turn the M.C. dial to select [FUNCTION], then press to confirm. 3 Turn the M.C. dial to select [BSM], then press to confirm.

To seek a station manually

After selecting the band, press / to select a station.

Press and hold / then release to seek an available station. Scanning stops when the unit receives a station. To cancel seek tuning, press / .

- 13 -- 13 -

English

NOTE

[SEEK] needs to be set to [MAN] in the FUNCTION settings (page 34).

NOTE

CAUTION

To store stations manually

While receiving the station you want to store, press and hold one of the number buttons (1/ to 6/ ) until it stops flashing.

You can select a preset channel by pressing and turning the M.C. dial. After selecting a channel, press and hold the M.C. dial to store a station.

CD/USB/iPhone/AUX

Playing back

Disconnect headphones from the device before connecting it to the unit.

Insert a disc into the disc loading slot with the label side up.

To eject a disc, stop playback first then press .

USB devices (including Android™)/iPhone

Open the USB port cover.

2 Plug in the USB device/iPhone using an appropriate cable.

To automatically switch to [USB] source when a USB device/ iPhone is connected to the uni t, set [USB AUTO] to [ON] in the SYSTEM settings (page 40).

Use an optional Pioneer USB cable (CD-U50E) to connect the USB device as any device connected directly to the unit will protrude out from the unit, which could be dangerous.

Before removing the device, stop playback.

AOA connections

For details on AOA connection, see page 30.

- 14 -

English

MTP connection

NOTE

A device installed with Android OS 4.0 or later can be connected to the unit via MTP, using the cable supplied with the device. However, depending on the connected device and the numbers of the files in the device, audi o files/songs may not be able to be played back via MTP. Note that MTP con nection is not compatible with WAV file formats and FLAC file formats, and cannot be used with the MIXTRAX function.

If you use an MTP connection, [PHONE CONNECT] needs to be set to [USB MTP] in the SYSTEM settings (page 40).

AUX

Insert the stereo mini plug into the AUX input jack.

2 Press SRC/OFF to select [AUX] as the source.

If [AUX] is set to [OFF] in the SYSTEM settings, [AUX] cannot be selected as a source (page 39).

Operations

You can make various adjustments in the FUNCTION settings (page 33). Note that the following operations do not work for an AUX device. To operate an AUX device, use the device itself.

Purpose Operation

Select a folder*1 Press 1/ or 2/. Select a track/song (chapter) Press or . Fast forward or reverse*2 Press and hold or . Search for a file from a list (CD/ USB only) 1 Press to display the list.

View a list of the files in the selected folder/ category*1

Play a song in the selected folder/ category*1

Repeat play Press 6/. Random/shuffle play Press 5/. Pause/resume playback Press 4/PAUS E.

2 Tur n the M.C. dial to select the desired

file (folder) name or category, then press to confirm.

3 Tur n the M.C. dial to select the desired

file, then press to confirm. Playback starts.

Press the M.C. dial when a folder/category is selected.

Press and hold the M.C. dial when a folder/ category is selected.

- 15 -- 15 -

English

NOTES

Important

Purpose Operation

Return to root folder (CD/USB only)*1 Press and hold 1/. Switch between compressed audio and CD-

DA (CD o nly)

*1 Compressed a udio files only *2 When you use the fast forward or reverse function while playing a VBR file, the playback time may

be not correct.

Press BAND/.

About MIXTRAX (USB/iPhone only)

The MIXTRAX function creates a non-stop mix of your music library, accompanied by illumination effects. For details on MIXTRAX settings, see page 43.

• iPhone needs to be connected with Pioneer ARC APP via USB for using this function (page 30).

• This function is not compatible with an Android device connected via MTP.

• Depending on the file/song, sound effects may not be available.

• Turn the MIXTRAX function off if the illumination effects it produces interfere with driving.

1 Press 3/MIX to turn MIXTRAX on/off.

Bluetooth

Bluetooth connection

If ten or more Bluetooth devices (e.g. a phone and separate audio player) are connected, they may not work properly.

1 Turn on the Bluetooth function of the device.

If you make a Bluetooth connection from the device, proceed to step 6.

2 Press to display the phone menu. 3 Turn the M.C. dial to select [BT SETTING], then press to confirm. 4 Turn the M.C. dial to select [ADD DEVICE], then press to confirm.

The unit starts to search for available devices, then displays them in the device list.

• To cancel searching, press the M.C. dial.

• If the desired device is not in the list, select [RE-SEARCH].

• If there is no device available, [NOT FOUND] appears in the display.

5 Turn the M.C. dial to select a device from the device list, then press to confirm.

- 16 -

English

Press and hold the M.C. dial to switch the displayed de vice information between the

NOTES

TIP

Bluetooth device address and device name. If you make a Bluetooth connection from the unit, proceed to step 7.

6 Select [Pioneer BT Unit] shown in the device display. 7 Make sure the same 6-digit number appears on this unit and the device, then

select “Yes” on the device.

• [DEVICE FULL] appears if the unit has already been paired with ten other devices. In this case, delete

one of the paired devices. See [DEL DEVICE] in the Bluetooth settings (page 17).

• Depending on the device, the PIN code is required in step 7. In this case, input [0000].

The Bluetooth connection can be also made by detecting the unit from the Bluetooth device. To do so, [VISIBLE] in the Bluetooth settings ne eds to be set to [ON]. For detail s on Bluetooth device operati ons, refer to the operating instructions supplied with the Bluetooth device.

Bluetooth settings

Menu Item Description DEVICELIST Display the list of paired Bluetooth devices. “*” appears on the

DEL DEVICE Delete the device information.

[DELETE YES], [DELETE NO]

ADD DEVICE Register a new device.

A.CONN Select [ON] to connect to a Bluetooth device automatically.

[ON], [OFF]

VISIBLE Select [ON] so that a Bluetooth device can detect the unit when

[ON], [OFF]

PIN CODE Change the PIN code.

device name when the Bluetooth connection is established. When no device is selected in the device list, this function is not available.

If ten devices are already paired, this function is not available. You can check the number of paired devices on the [DEVICELIST] setting.

the unit is connected via Bluetooth to another device.

1 Press the M. C. dial to display the setting mode. 2 Turn t he M.C. dial to select a number. 3 Press the M. C. dial to move the cursor to the next position. 4 After inputting the PIN code, press and hold the M.C. dial.

After inputting the PIN code, pressing the M.C. dial returns you to the PIN code input display, and you can change the PIN code.

- 17 -- 17 -

English

Important

Menu Item Description DEV. INFO Switch the device information on the display between the

A.PAIRING Select [ON] to pair the unit and iPhone or Android device

[ON], [OFF]

device name and Bluetooth device address.

automatically when an iPhone or Android device is connected to the unit via USB. (This function may not be available depending on the version of iOS you are using.)

• When you are using an Android device, this function is

available in the following situations:

– Your device has Android OS 4.4 or later installed. – Be sure to turn on the B luetooth function of the devi ce and confirm

that the device is not connected to the unit via Bluetooth. – [P.APP AUTO ON] needs to be set to [ON] (page40). – Pioneer ARC APP needs to be installed on your Android device and

[PHONE CONNECT] needs to b e set to [APP CONTROL] (page 30). – A confirmation butt on should be pressed on the caution window

displayed on Pioneer ARC APP after a connection with the Pioneer

ARC APP is made.

Bluetooth telephone

First, make a Bluetooth connection with the Bluetooth telephone (page 16). Up to two Bluetooth telephones can be connected simultaneously.

• Leaving the unit on standby to connect to your phone via Bluetooth while the engine is not running

can drain the vehicle’s battery.

• Be sure to p ark your vehicle in a safe place and apply the parking brake before operation.

To make a phone call

Press to display the phone menu.

When two phones are connected, a phone name appears first then a phone menu will display. To switch to another phone, press again.

2 Tu rn the M.C. dial to select [RECENTS] or [PHONE BOOK], then press to confirm.

If you select [PHONE BOOK], proceed to step 4.

3 Tu rn the M.C. dial to select [MISSED], [DIALED] or [RECEIVED], then press to

confir m.

4 Tu rn the M.C. dial to select a name or phone number, then press to confirm.

The phone call starts.

To answer an incoming call

Press when a call is received.

- 18 -

English

TIP

When two phones are connected to the unit via Bluetooth and there is an incoming call while one

NOTE

phone is being used for a call, a message will appear in the display. To answer that incoming call, you need to end the existing call.

Basic operations

Purpose Operation

End a call Press . Reject an incoming call Press and hold when a call is received. Switch between the current caller

and a caller on hold Cancel a caller on hold Press and hold . Adjust the volume of the caller’s

voice (When private mode is on, this function is not available.)

Turn the private mode on or off Press BAND/ during the call.

Press the M.C. dial.

Tur n the M.C. dial during the call.

To preset phone numbers

Select a phone number from a phone book or call history.

2 Press and hold one of the number buttons (1/ to 6/).

The contact is stored in the selected preset number.

To make a call using a preset number, press one of the number buttons (1/ to 6/), then press the M.C. dial.

Voice recognition (Only for iPhone)

This function is only available when an iPhone equipped with voice recognition is connected to the unit via Bluetooth.

1 Press and hold to activate the voice recognition mode. 2 Press the M.C. dial and then talk into the microphone to input voice commands.

To exit the voice recognition mode, press BAND/.

For details on the voice recognition features, refer to the manual supplied with your iPhone.

- 19 -- 19 -

English

Phone menu

Important

Menu Item Description RECENTS Display the missed call history.

[MISSED] [DIALED] Display the dialed call history. [RECEIVED] Display the received call history.

PHONE BOOK Display the contacts in your phone. Set [VISIBLE] in the

PRESET 1-6 Recall the preset phone numbers. You can also recall the preset

A.ANSR* Select [ON] to answer an incoming call automatically.

[ON], [OFF]

R.TONE Select [ON] if the ring tone does not come out from the car

[ON], [OFF]

PB INVT Invert the order of names in the phone book (name view). BT SETTING You can adjust various settings for Bluetooth connections. For

* If two phones are connected, this function does not work on incoming calls that are received while

one of the phones is being used for a call.

Bluetooth settings to [ON] to browse the contacts via this unit.

phone numbers by pressing one of the number buttons (1/ to 6/).

speakers. Depending on the connected phone, this function may not work.

details on Bluetooth settings, see page 17.

Bluetooth audio

• Depending on the Bl uetooth audio player connected to this unit, the available operations will be

limited to the following two levels: – A2DP (Advanced Audio Dist ribution Profile) can only play back songs on you r audio player. – AVRCP (Audio/Video Remote Control Profile) can perform functions such as playback, pause, select

song, etc.

• The sound of the Bluetooth audio player will be muted when the phone is in use.

• When the Bluetooth audio player is in use, you cannot connect to a Bluetooth telephone

automatically.

• Depending on the type of Bluetooth audio player you have connected to this unit, operation and

information displayed may vary based on availability and functionality.

1 Make a Bluetooth connection with the Bluetooth audio player. 2 Press SRC/OFF to select [BT AUDIO] as the source. 3 Press BAND/ to start playback.

- 20 -

English

Basic operations

Important

You can make various adjustments in the FUNCTION settings (page 33).

Purpose Operation

Fast forward or reverse Press and hold or . Select a track Press or . Repeat play* Press 6/. Random play* Press 5/. Pause/resume playback Press 4/PAUS E. Search for a file from a list 1 Press to display a list.

Switch the Bluetooth device name in the device list according to the connec tion order

* Depending on the connected device, these operations may not be available.

2 Tur n the M.C. dial to select the desired

folder name, then press to confirm.

3 Tur n the M.C. dial to select the desired

file, then press to confirm.

Playback starts. Press 1/ or 2/.

App Mode

You can enjoy listening to an application on an iPhone/Android device via the unit. In some cases, you can control an application by using the unit. For details on compatible devices, visit our website.

Use of third part y apps may involve or require the provisio n of personally identifiable information, whether through the creation of a user account or otherwise, and for certain applications, the provision of geolocation da ta. ALL THIRD PART Y APPS ARE THE SOLE RESPONSIBILITY OF THE PROVIDERS, INCLUDING WITHOUT LIMITATION COLLECTION AND SECURITY OF USER DATA AND PRIVACY PRACTICES. BY ACCESSING THIRD PARTY APPS, YOU AGREE TO REVIEW THE TERMS OF SERVICE AND PRIVACY POLICIES OF THE PROVIDERS. IF YOU DO NOT AGREE WITH THE TERMS OR POLICIES OF ANY PROVIDER OR DO NOT CONSENT TO THE USE OF GEOLOCATION DATA WHERE APPLICABLE, DO NOT USE THAT THIRD PARTY APP.

For iPhone use rs

This function is compatible with iPhones installed with iOS 6.0 or later.

For Android device users

This function is compatible with devices that have Android OS 2.3 or later installed.

- 21 -- 21 -

English

NOTE

PIONEER IS NOT LIABLE FOR ANY THIRD PARTY APPS OR CONTENT, INCLUDING WITHOUT LIMITATION

NOTE

THEIR ACCURACY OR COMPLETENESS. THE CONTENT AND FUNCTIONALITY OF SUCH APPS ARE THE SOLE RESPONSIBILITY OF THE APP PROVIDER.

Playback of an application via the unit

1 Connect this unit with the mobile device.

• iPhone via USB (page 14)

• iPhone/Android device via Bluetooth (page 16)

2 Press the M.C. dial to display the main menu. 3 Turn the M.C. dial to select [SYSTEM], then press to confirm. 4 Turn the M.C. dial to select [PHONE CONNECT], then press to confirm. 5 Turn the M.C. dial to select one of the below, then press to confirm.

• Select [IPHONE] for iPhone.

• Select [ANDROID] for Android device.

6 Turn the M.C. dial to select one of the below.

• Select [WIRED] for the USB connection.

• Select [BLUETOOTH] for the Bluetooth connection.

When the connec tion setting is changed, a me ssage that lets you know that the connectio n setting had been changed will appear in the display. Press the M.C. dial and turn the M.C. dial to select [SRC OFF :YES], then press to confirm . The unit turns off automatica lly and the setting is executed.

7 Press SRC/OFF to select [APP]. 8 Operate the mobile device to start up the application.

When you connect a mobile device other than iPhone/Android device, select [OTHERS] in the [PHONE CONNECT] menu and select [WIRED] (for the USB connection) or [BLUETOOTH] (for the Bluetooth connection). Depending on your mobile device, it may not operate correctly.

Basic operations

You can make various adjustments in the FUNCTION settings (page 33).

Purpose Operation

Select a track Press or . Fast forward or reverse Press and hold or . Pause/resume playback Press BAND/.

- 22 -

English

NOTE

Pandora®

Pandora internet radio is a music service not affiliated with Pioneer. More information is available at http://www.pandora.com. The Pandora mobile application is available for iPhone and Android phones. Please visit www.pandora.com/everywhere/mobile for the latest compatibility information.

Listening to Pandora

Update the firmware of the Pandora application to the latest version before use.

1 Connect this unit with the mobile device.

• iPhone via USB (page 14)

• iPhone/Android device via Bluetooth (page 16)

If you choose a USB connection, proceed to step 6.

2 Press SRC/OFF to select [PANDORA]. 3 Press and hold 1/ to display [PHONE CONNECT]. 4 Turn the M.C. dial to select one of the below, then press to confirm.

• Select [IPHONE] for iPhone.

• Select [ANDROID] for Android device.

5 Turn the M.C. dial to select [BLUETOOTH] for iPhone/Android device via

Bluetooth.

6 Press SRC/OFF to select [PANDORA]. 7 Launch the Pandora application on the mobile device and start playback.

Basic operations

You can make various adjustments in the FUNCTION settings (page 33).

- 23 -- 23 -

English

NOTE

Purpose Operation

Skip a track Press . Switch between Shuffle and the

station Change the sort order Press (list), then select one of the following.

Play When Shuffle or the station is selected, press the

Delete a station 1 When the station is selected, press and hold the

Pause/resume playback Press 4/PAUSE. Thumbs U p Press 1/. Thumbs D own Press 2/. Create a new station based on the

track currently being played Create a new station based on the

artist currently being played Store the track information currently

being played in your Pandora account.

Some functions of Pandora may not be operated from the unit.

Press (list), then turn the M.C. dial to select the Shuffle or the desired station.

[ABC]: Sort the items in the list alphabetically. [DATE]: Sort the items in the list in order of the

dates on which the items were created.

M.C. dial.

[DELETE YES] appears.

2 Press the M.C. dial. To cancel, press BAND/ in step 1.

Press and hold 5/.

Press and hold 6/.

1 Press and hold 3/MIX.

[BOOKMARK] appears.

2 Press the M.C. dial.

Spotify®

Spotify is a music streaming distribution service not affiliated with Pioneer. More information is available at http://www.spotify.com. The Spotify application is available for compatible smartphones, please visit https:// support.spotify.com/ for the latest compatibility information. To enjoy Spotify as you drive, first download the Spotify app to your iPhone or Android device. You can download it on the iTunes App Store or Google Play™. Choose a free account or a paid Premium account, either in the app or at spotify.com. A Premium account gives you more features, like offline listening.

- 24 -

English

Important

• This product incorporates Spotify software which is subject to 3rd party licenses found here:

NOTE

www.spotify.com/connect/third-party-licenses.

• For information on the countries a nd regions where Spotify can be us ed, take a look at https://

www.spotify.com/us/select-your-country/.

Listening to Spotify

Update the firmware of the Spotify application to the latest version before use.

1 Connect this unit with the mobile device.

• iPhone via USB (page 14)

• iPhone/Android device via Bluetooth (page 16)

If you choose a USB connection, proceed to step 6.

2 Press SRC/OFF to select [SPOTIFY]. 3 Press and hold 1/ to display [PHONE CONNECT]. 4 Turn the M.C. dial to select one of the below, then press to confirm.

• Select [IPHONE] for iPhone.

• Select [ANDROID] for Android device.

5 Turn the M.C. dial to select [BLUETOOTH] for iPhone/Android device via

Bluetooth.

6 Press SRC/OFF to select [SPOTIFY]. 7 Launch the Spotify application on the mobile device and start playback.

Basic operations

You can make various adjustments in the FUNCTION settings (page 33).

The available operations may vary according to the type of contents (track/album/artist/playlist/radio) you want to play.

- 25 -- 25 -

English

NOTE

Purpose Operation

Skip a track Press or . Search for a track from a list 1 Press (list) to display the list.

Pause/resume playback Press 4/PAUSE. Thumbs Up (Only for radio) Press 1/. Thumbs Down (Only for radio) Press 2/. Random play (Only for track/album/artist/

playlist) Repeat play (Only for track/album/artist/

playlist) Start a radio channel based on the song

currently being played.

Some functions of Spotify may not be operated from the unit.

2 Tur n the M.C. dial to select the desired

category, then press to confirm.

3 Tur n the M.C. dial to select the desired

file, then press to confirm. Playback starts.

Press 5/.

Press 6/.

1 Press and hold 5/ to start a radio. 2 Press the M.C. dial.

• This function may not be available

depending on the selected song.

SiriusXM Satellite Radio

(Only for FH-S700BS/S701BS)

Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satell ite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com

Replay™

You can pause, rewind or replay live satellite radio as well as the channel you are currently listening to.

Tun eSta rt™

Automatically start songs from the beginning when you tune to one of your preset music channels stored on the current band of presets. For details, refer to TUNE STA RT on page 35.

- 26 -

English

NOTE

TuneStart is compatible with SXV200 or later tuner models. Not compatible with SXV100.

NOTE

Tun eSca n™

Scan through short previews of songs you may have missed on music channels stored on the current band of presets. Each song in the current channel plays for six seconds at a time. For details, refer to TUNE SCAN (scanning the songs) on page 35.

TuneScan is compatible with SXV200 or later tuner models. Not compatible with SXV100.

Tun eMix ™

Create a music channel that’s a blend of songs made up from the music channels stored on the current band of presets. For details, refer to TUNEMIX on page 35.

TuneMix™ is compatible with the SXV300 or later tuner models. Not compatible with the SXV200 or SXV100.

Preparing for the SiriusXM Satellite Radio service

1 Press SRC/OFF to select [SIRIUSXM]. 2 Press / to select Channel 0.

The Radio ID appears on the display. In addition, the Radio ID is located on the bottom of the SiriusXM Connect Vehicle Tuner.

The Radio ID does not include the letters I, O, S or F.

3 Activate the SiriusXM service online or by phone.

For US Subscriptions:

• Visit www.siriusxm.com/activatenow

• Call SiriusXM Listener Care at 1-866-635-2349

For Canadian Subscriptions:

• Visit www.siriusxm.ca/activatexm

• Call 1-877-438-9677

4 [SUBSCRIPTION UPDATED] appears on the display when your SiriusXM Connect

Vehicle Tuner has been subscribed successfully.

Press any key to clear the activation message.

The activatio n process usually takes 10 minu tes to 15 minutes but may take up to an hour in some cases. Do not turn off the unit until you clear the activation message in step 4.

- 27 -- 27 -

English

NOTE

Listening to a channel

1 Press and hold DISP, then select [CHANNEL].

You can also select the operation mode by the SiriusXM settings (page 34).

2 Press SRC/OFF to select [SIRIUSXM]. 3 Press BAND/ to select a band from [SXM1], [SXM2] or [SXM3]. 4 Press / to select a channel.

Pressing and holding either button will rapidly browse through the channels. Press and hold either button then release to tune automatically. Scanning stops when the unit receives a channel. To cancel seek tuning, press / .

Basic operations

Press and hold DISP to select the operation mode [CHANNEL] or [REPLAY].

You can exit the replay mode by pressing and holding BAND/.

Purpose Operation

Select a channel 1 Set the operation mode to [CHANNEL].

Skip backward/forward 1 Set the operation mode to [REPLAY].

Fast forw ard or reve rse 1 Set the oper ation mode to [REPLAY].

You can also make various adjustments in the SiriusXM settings (page 34).

Category scan

The live broadcast for each channel in the current category plays for six seconds at a time. Follow the instructions below.

To search for a channel from a list

1 Press during playback. 2 Tu rn the M.C. dial to select a category. 3 Select one of the operations below.

Category scan: Press and hold the M.C. dial to switch to category scan.

2 Press or . Pressing and holding either button will rapidly browse through the channels.

2 Press or .

2 Press and hold or .

- 28 -

English

Channel search: Press the M.C. dial to stop a scan.

NOTE

Press DISP to change the display information between “Channel Name”, “Artist Name”, “Song Title”, “Content Info” and “Channel Nu mber”.

Scan options

Purpose Operation

Stopping a scan (selecting the channel or song playing)

Switching to the next/previous song during Tun eSc an

Switching to the next/previous channel during the category scan

Aborting a scan (The last channel or song will continue to play when scan ends.)

Press the M.C. dial.

Press or .

Press BAND/.

Channel Preset

To preset a channel

1 While receiving a channel you want to store, press and hold one of the number

buttons (1/ to 6/ ) until it stops flashing.

To play the stored channels, select the band and then press a number button (1/ to 6/).

To preset a channel from the program list

1 While receiving a channel you want to store, press . 2 Tu rn the M.C. dial to select [PRESETS], then press to confirm. 3 Tu rn the M.C. dial to select a preset channel. 4 Press and hold the M.C. dial to store.

To play the stored channels, turn the M.C. dial to select a preset channel, then press to confirm.

Parental Control

Some SiriusXM channels conta in mature content. You can lock these channels. For details, see [PARENTAL CTRL] in SiriusXM settings (page 36).

- 29 -- 29 -

English

WAR NIN G

NOTE

Using Pioneer ARC APP

You can operate the unit from Pioneer ARC APP installed on an iPhone/Android device. In some cases, you can control aspects of the application, such as source selection, pause, etc., by using the unit. For details on what operations are available on the application , see the application’s help section.

Do not attempt to op erate the application while dr iving. Make sure to pull off the road and pa rk your vehicle in a safe location before attempting to use the controls on the application.

For iPhone use rs

This function is compatible with iPhones (iPhone 5 or later) installed with iOS 8.0 or later. You can download Pioneer ARC APP on iTunes App Store.

For Android device users

This function is compatible with devices that have Android OS 4.1 or later installed and also support AOA (Android Open Accessory) 2.0. You can download Pioneer ARC APP on Google Play.

Some Android devices connected via AOA 2.0 may not work properly or emit sounds due to their own software design , regardless of the OS version.

Making a connection with Pioneer ARC APP

1 Connect this unit with the mobile device.

• iPhone/Android device via USB (page 14)

• iPhone/Android device via Bluetooth (page 16)

• Select [IPHONE] for iPhone.

• Select [ANDROID] for Android device.

- 30 -

+ 165 hidden pages