Pioneer DRM-AF751 User Manual

50-DISC MAGAZINE

DRM-AF751

Operating instructions

Thank you for buying this Pioneer product.
Please read through these operating
instructions so you will know how to
operate your model properly.
This product is an optional unit designed
for exclusive use as the 700-disc changers,
models DRM-7000. This means that this
unit cannot be used alone or connected to
other equipment than specified.

The export of this product or devices in
which this product has been installed
from Japan is regulated by Japanese
government. The export of this product
may be prohibited without
governmental license. To export or re­export of this product from a country
other than Japan may also be prohibited
without an export license from the
country involved.

WARNING: TO PREVENT FIRE OR

SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.

IMPORTANT NOTICE:

RECORD THE MODEL NUMBER AND
SERIAL NUMBER OF THIS
EQUIPMENT BELOW. THE NUMBERS
ARE ON THE TOP PANEL.

MODEL NO. DRM-AF751
SERIAL NO.

KEEP THESE NUMBERS FOR
FUTURE USE.

IMPORTANT

The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.

2

<DRC1107>
En

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his
own expense.

[For Canadian model]

This Class A digital apparatus complies with Canadian ICES-003.

[Pour le modèle Canadien]

Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the
user’s right to operate the equipment.

Handling the discs

÷ Avoid touching the signal surface when you

use a disc.

÷ To hold it, place your fingers on the edge of

the disc or the edge of the center hole and
the disc edge.

÷ DO NOT use non-standard discs, as these

may adversely influence this unit and other
equipment.

÷ DO NOT play a CD having other shape than

a circular disc, such as heart shaped disc, or
malfunction may occur.

English

÷ Do not attach paper or stickers to the label

side of the disc. Handle discs carefully and
avoid damaging the label.

÷ Discs rotate at high speed in the changer.

Do not use defective discs (e.g., cracked or
considerably warped). Such discs may
damage the changer.

Do not use the following types of discs for they
may cause malfunction of the unit or damage
to the discs:
÷ Disc which has a molding flash (projected

fin) left on the periphery as shown in the
illustration.

÷ Disc with its edges are rounded or tapered

as shown in the figure.

3

<DRC1107>

En

FEATURES

¶ Able to accommodate 50 discs
¶ Disc holder lock/release mechanism

Discs may be locked into position or released by turning the release knob.

¶ Memory

Disc magazines are equipped with memory which makes it possible to read IDs to
identify individual magazines and make the management of offline media easier.

A HARDWARE TOUR

Lock pin

Release
knob

Handle

Electrode

NOTES:

¶

Electrodes are highly susceptible to damage from static electricity, and for this reason
you should always be careful not to allow your hands to come into contact with the
electrodes.

¶

Always be sure to place disc magazines into the provided dust covers when storing
magazines.

4

<DRC1107>
En

TO INSTALL THE DISC MAGAZINE

For instructions on how to open the
access doors, see the operating
instructions for the DRM-7000 disc
changer.

1. Insert discs into a disc magazine.

1 Turn the release knob to the vertical direction

to unlock.

2 Insert discs.
3 Turn the release knob to the horizontal

direction to lock the discs into place.

Release knob

Lock release

Label

Lock

2. Insert magazine into changer.

Holding the handle of the disc magazine,
insert the disc magazine into the changer
following the changer guide rails until it
runs against the stopper.
And turn the handle to the left with
pushing the magazine in so that the lock
pin on the left of the magazine slides into
the corresponding hole along the side of
the changer.

Lock pin

Hole

Guide
rails

≠

English

NOTES:

¶

Insert with label facing upward.

¶

Insert discs horizontally. Otherwise it may
result in damage to the discs.

¶

Take care not to scratch or do other damage
to the recording faces of discs.

¶

Do not turn a disc magazine upside down
while the lock is disengaged. Otherwise it
may result in discs falling out of the
magazine.

¶

Discs may not be inserted or removed when
the magazine is locked, and the use of
excessive force when trying to do so may
result in damage to discs or to the disc
magazine.

Handle

Shown above is the insertion to the front
magazine bay. Though the insertion to the
rear magazine bay is almost same but note
that the proper installation position is in
the place where it is very secluded.
To remove a disc magazine from the
changer, pull the handle towards you and
pull the magazine from the changer.

5

<DRC1107>

En

SPECIFICATIONS

Maximum number of discs 50 discs
Operating temperature +5°C +35°C
Operating humidity 5 - 85% (no condensation)
Storage temperature –40°C + 60°C
Weight 1,5 kg
External dimensions 184.8 (W) x 156.3 (H) x 173 (D)

NOTE:

Specifications and design subject to possible modifications without notice, due to improvements.

6

<DRC1107>
En

AFTER-SALES SERVICE FOR PIONEER PRODUCTS

い











Please contact the dealer or distributor from where you purchased the product for its after­sales service (including warranty conditions) or any other information. In case the necessary
information is not available, please contact the Pioneer’s subsidiaries (regional service
headquarters) listed below:

PLEASE DO NOT SHIP YOUR PRODUCT TO THE COMPANIES
at the addresses listed below for repair without advance contact, for these companies are
not repair locations.

AMERICA
PIONEER ELECTRONICS SERVICE, INC.
CUSTOMER SUPPORT DIVISION
P.O. BOX 1760, LONG BEACH, CA 90801-1760, U.S.A.

EUROPE
PIONEER ELECTRONIC (EUROPE) N.V.
EUROPEAN SERVICE DIVISION
HAVEN 1087, KEETBERGLAAN 1, 9120 MELSELE, BELGIUM

ASEAN
PIONEER ELECTRONICS ASIACENTRE PET. LTD.
SERVICE DEPARTMENT
501 ORCHARD ROAD, #10-00
WHEELOCK PLACE, SINGAPORE 238880

JAPAN AND OTHERS
PIONEER ELECTRONIC CORPORATION (HEAD OFFICE)
CUSTOMER SUPPORT CENTER
4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654 JAPAN

や

に



さ

う



し

ゅ

ち

み

き

ど

この取扱説明書はエコマーク認定

る

も

り

ま

の再生紙を使用しています。

を

France : tapez 36 15 PIONEER

Published by Pioneer Electronic Corporation.
Copyright © 1999 Pioneer Electronic Corporation.

C1999パイオニア株式会社 禁無断転載

All rights reserved.

153-8654東京都目黒区目黒１丁目４番１号

PIONEER ELECTRONIC CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan

Business System Company: 15-5, Ohmorinishi 4-Chome, Ohta-ku, Tokyo 143-8564 Japan TEL: [phone]

PIONEER NEW MEDIA TECHNOLOGIES, INC.

Laser Optical Systems Division: 2265 East 220th Street, Long Beach, CA 90810, U.S.A. TEL: [phone]

PIONEER ELECTRONIC [EUROPE] N.V.

PIONEER House, Hollybush Hill, STOKE POGES, SLOUCH SL2 4QP U.K. TEL: [phone]

PIONEER ELECTRONICS OF CANADA, INC.

Industrial Products Department: 300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: [phone]

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia TEL: [phone]

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

<99E00SF0M00> Printed in Japan/Imprimé au Japon <DRC1107-A>

501 Orchard Road, #10-00, Wheelock Place, Singapore 238880 TEL: [phone]