PIONEER DEH P860MP, DEHP8600MP, DEH P8650MP Service Manual

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2004
ORDER NO.
CRT3217
DEH-P860MP/XN/UC
MULTI-CD CONTROL DSP HIGH POWER CD/MP3/WMA PLAYER WITH FM/AM TUNER
DEH-P860MP
DEH-P8600MP DEH-P8650MP
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks
CX-3098 CRT3179 S10WMAcode2 CD Mech. Module:Circuit Description, Mech. Description, Disassembly
/XN/UC /XN/ES
/XN/UC
For details, refer to "Important symbols for good services".
K-ZZD.MAR. 2004 printed in Japan
1234

SAFETY INFORMATION

CAUTION
A
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
complex products such as those covered by this manual.
repair Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. trying to do so
ARNING
W
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state
B
Health & Safety Code Section 25249.6 - Proposition 65
If you are not qualified to perform the repair of this product properly and safely, you should not risk
and refer the repair to a qualified service technician.
of California to cause cancer, birth defects or other reproductive harm.
- CD Player Service Precautions
1. Before disassembling the unit, be sure to turn off the
C
D
power. Unplugging and plugging the connectors dur­ing power-on mode may damage the ICs inside the unit.
2. To protect the pickup unit from electrostatic dis­charge during serviving, take an appropriate treat­ment(shorting-solder) by referring to "the DISAS­SEMBLY" on page 62.
3. After replacing the pickup unit, be sure to check the grating.(See p.58.)
E
F
2
1234
DEH-P860MP/XN/UC
5678
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely. When you find the procedures bearing any of the symbols, be sure to fulfill them:
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual.
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable. In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning, proper cleaning should be performed to restore their performances.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
A
B
5. Lubricants, glues, and replacement parts
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used.
C
D
56
DEH-P860MP/XN/UC
E
F
7
8
3

CONTENTS

SAFETY INFORMATION.....................................................................................................................................2
A
B
C
1. SPECIFICATIONS............................................................................................................................................ 5
2. EXPLODED VIEWS AND PARTS LIST............................................................................................................ 8
2.1 PACKING(DEH-P860MP/XN/UC,DEH-P8600MP/XN/UC).........................................................................8
2.2 PACKING(DEH-P8650MP/XN/ES)...........................................................................................................10
2.3 EXTERIOR(1) .......................................................................................................................................... 12
2.4 EXTERIOR(2) .......................................................................................................................................... 14
2.5 CD MECHANISM MODULE.....................................................................................................................16
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM..........................................................................................18
3.1 BLOCK DIAGRAM................................................................................................................................... 18
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE).............................................................................. 20
3.3 KEYBOARD UNIT.................................................................................................................................... 26
3.4 CD MECHANISM MODULE(GUIDE PAGE)............................................................................................ 28
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 38
4.1 TUNER AMP UNIT...................................................................................................................................38
4.2 SWITCH UNIT..........................................................................................................................................42
4.3 KEYBOARD UNIT.................................................................................................................................... 43
4.4 CD MECHANISM MODULE.....................................................................................................................44
5. ELECTRICAL PARTS LIST ............................................................................................................................ 46
6. ADJUSTMENT ............................................................................................................................................... 55
6.1 JIG CONNECTION DIAGRAM.................................................................................................................55
6.2 CD ADJUSTMENT................................................................................................................................... 56
6.3 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.................................................... 58
6.4 ERROR MODE ........................................................................................................................................ 60
6.5 OEL SCREENSAVER STUDIO LKA TO LKD APPLICATION.................................................................. 61
6.6 SYSTEM MICROCOMPUTER TEST PROGRAM ................................................................................... 61
7. GENERAL INFORMATION.............................................................................................................................62
7.1 DIAGNOSIS............................................................................................................................................. 62
7.1.1 DISASSEMBLY ..................................................................................................................................... 62
7.1.2 CONNECTOR FUNCTION DESCRIPTION.......................................................................................... 66
7.2 IC .............................................................................................................................................................67
7.3 OPERATIONAL FLOW CHART............................................................................................................... 81
7.4 CLEANING............................................................................................................................................... 82
8. OPERATIONS ................................................................................................................................................83
1234
D
E
F
4
1234
DEH-P860MP/XN/UC
5678

1. SPECIFICATIONS

A
B
C
D
E
56
DEH-P860MP/XN/UC
F
7
8
5
1234
A
B
C
D
E
F
6
1234
DEH-P860MP/XN/UC
5678
A
B
C
D
E
56
DEH-P860MP/XN/UC
F
7
8
7
N
1234

2. EXPLODED VIEWS AND PARTS LIST

OTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
A
• Screw adjacent to mark on the product are used for disassembly.
"
• For the applying amount of lobricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.)

2.1 PACKING(DEH-P860MP/XN/UC,DEH-P8600MP/XN/UC)

5
9
12
8
B
28
13
C
11
7
10
6
15
14
4
16
17
3
26
1
27
2
20
D
19
24
E
25
18
23
24
21
F
8
1234
23
22
DEH-P860MP/XN/UC
5678
(1) PACKING(DEH-P860MP/XN/UC,DEH-P8600MP/XN/UC) SECTION PARTS LIST
Mark
Mark No. Description Part No.
1 Cord Assy See Contrast table(2) 2 Cord Assy CDE7701 3 Accessory Assy CEA4302 4 Spring CBH1650 5 Screw Assy CEA4303
6 Screw CBA1650 7 Bolt(M5x16) CBA1783 * 8 Polyethylene Bag CEG-127 9 Screw CRZ50P090FTC 10 Screw JPZ20P060FZK
11 Nut NF50FTC 12 Screw TRZ50P080FTC * 13 Polyethylene Bag CEG-158 14 Handle CNC5395 15 Strap CNC5402
16 Bush CNV3930 17-1 Polyethylene Bag CEG1116
No. Description Part No.
17-2 Owner's Manual See Contrast table(2) 17-3 Installation Manual See Contrast table(2) * 17-4 Causion Card CRP1308
17-5 Causion Card CRP1310 * 17-6 Warranty Card See Contrast table(2) * 17-7 Card See Contrast table(2) 18 Polyethylene Bag CEG1173 19 Carton See Contrast table(2)
20 Sub Carton CHG5195 21 Contain Box See Contrast table(2) 22 Protector CHP2546 23 Protector CHP2797 24 Protector CHP2798
25 Protector CHP2812 26 Microphone Assy CPM1054 27 Case Assy CXB3520 28 Remote Control Unit CXC2665
A
B
(2) CONTRAST TABLE
DEH-P860MP/XN/UC and DEH-P8600MP/XN/UC are constructed the same except for the following:
Mark NO Description DEH-P860MP/XN/UC DEH-P8600MP/XN/UC
1 Cord Assy CDE7436 CDE7437 17-2 Owner's Manual CRD3828 CRD3830 17-3 Installation Manual CRD3829 CRD3831 * 17-6 Warranty Card CRY1070 Not used * 17-7 Card Not used ARY1048
19 Carton CHG5194 CHG5193 21 Contain Box CHL5194 CHL5193
Owner's Manual,Installation Manual
Part No. Language
CRD3828 English, French CRD3829 English, French CRD3830 English, French CRD3831 English, French
C
D
E
56
DEH-P860MP/XN/UC
F
7
8
9
1234

2.2 PACKING(DEH-P8650MP/XN/ES)

A
5
9
12
8
28
13
B
27
C
6
3
14
4
16
17
26
1
2
20
19
24
D
25
E
21
F
24
23
22
18
23
10
1234
DEH-P860MP/XN/UC
5678
----
PACKING(DEH-P8650MP/XN/ES) SECTION PARTS LIST
Mark No. Description Part No.
1 Cord Assy CDE7436 2 Cord Assy CDE7701 3 Accessory Assy CEA4301 4 Spring CBH1650 5 Screw Assy CEA3849
6 Screw CBA1650 7 ••••• * 8 Polyethylene Bag CEG-127 9 Screw CRZ50P090FTC 10 •••••
11 ••••• 12 Screw TRZ50P080FTC * 13 Polyethylene Bag CEG-158 14 Handle CNC5395 15 •••••
16 Bush CNV3930 17-1 Polyethylene Bag CEG1116
Mark
No. Description Part No.
17-2 Owner's Manual CRD3832 17-3 Owner's Manual CRD3833 17-4 Owner's Manual CRB1902
17-5 Installation Manual CRD3834 * 17-6 Causion Card CRP1308 17-7 Causion Card CRP1310 18 Polyethylene Bag CEG-162 19 Carton CHG5192
20 Sub Carton CHG5195 21 Contain Box CHL5192 22 Protector CHP2546 23 Protector CHP2797 24 Protector CHP2798
25 Protector CHP2812 26 Microphone Assy CPM1054 27 Case Assy CXB3520 28 Remote Control Unit CXC2665
A
B
----
Owner's Manual,Installation Manual
Part No. Language
CRD3832 English, Spanish CRD3833 Portuguese(B), T r aditional Chinese CRB1902 Arabic CRD3834 English, Spanish, Portuguese(B), Traditional Chinese, Arabic
C
D
E
56
DEH-P860MP/XN/UC
F
7
8
11
1234

2.3 EXTERIOR(1)

A
B
52
32
58
36
39
49
40
45
57
47
42
48
44
31
30
25
41
43
35
37
51
31
31
C
46
C
55
34
33
50
29
1
29
22
23
D
A
2
67
66
64
2
69
66
62
59
63
E
53
(2/2)
56
38
19
14
3
7
9
B
15
10
16
17
4
5
6
12 4
5
13
B
(2/2)
11
4
4
8
26
21
24
18
28
20
29
1
29
61
F
12
65
: GEM1024
60
68
62
59
54
27
4
4
DEH-P860MP/XN/UC
1234
5678
(1) EXTERIOR(1) SECTION PARTS LIST
Mark No. Description Part No.
1 Screw(M2x2.5) CBA1641 2 Screw(M2.6x4) CBA1769 3 Drive Unit See Contrast table(2) 4 Screw BMZ26P040FTC 5 Screw CBA1633
6 Spring CBL1632 7 Cord CDE7392 8 Holder CND1848 9 Holder CND1850 10 Insulator CNM8797
11 Gear CNV7752 12 Gear CNV7753 13 Gear CNV7754 14 Gear CNV7755 15 Switch Unit CWS1389
16 Switch(S1) CSN1051 17 Spring Switch(S2) CSN1052 18 Holder Unit CXC2196 19 Holder Unit CXC2197 20 Arm Unit CXC2198
21 Arm Unit CXC2199 22 Arm Unit CXC2200 23 Arm Unit CXC2201 24 Motor Unit(M571) CXC2204 25 Holder CNC8659
26 Gear Unit CXC2205 27 Chassis Unit See Contrast table(2) 28 Screw JFZ20P025FTC 29 Washer YE15FTC 30 Detach Grille Assy See Contrast table(2)
31 Screw BPZ20P090FZK 32 Button(OPEN) CAC8459 33 Button(RESET) CAC8461 34 Button(1-6) CAC8919 35 Spring CBH2543
No. Description Part No.
Mark
36 Holder CND2039 37 Arm CNV6963 38 Lighting Conductor CNV7974 39 Lighting Conductor CNV7975 40 Keyboard Unit CWM9270
41 Flat Cable CDE7591 42 Jack(CN1902) CKN1016 43 Connector(CN1802) CKS4792 44 Connector(CN1903) CKS4795 45 Holder CND1971
46 Sheet CNM8658 47 Sheet CNM9192 48 OEL Module MXK8200 49 Button Unit(EQ) CXC2684 50 Button Unit(BAND/ESC) CXC2685
51 Cover Unit CXC2997 52 Knob Unit CXC3698 53 Knob Unit CXC3699 54 Panel CNS7795 55 Sub Grille Assy See Contrast table(2)
56 Panel Unit CXC2603 57 Remote Control Unit CXC2665 58 Cover CZN5357 59 Screw(M2x2) CBA1561 60 Screw(M2x2) CBA1633
61 Screw(M2x3.5) CBA1754 62 Spring CBH2530 63 Connector CKS4796 64 Holder CND2172 65 Flexible PCB CNP7698
66 Arm CNV6962 67 Guide CNV6967 68 Guide CNV8048 69 Case Unit CXC2202
A
B
C
D
(2) CONTRAST TABLE
DEH-P860MP/XN/UC DEH-P8600MP/XN/UC, and DEH-P8650MP/XN/ES are constructed the same except f or the following:
Mark NO Description DEH-P860MP/XN/UC DEH-P8600MP/XN/UC DEH-P8650MP/XN/ES
3 Drive Unit CXC3136 CXC3135 CXC3015 27 Chassis Unit CXC3134 CXC3133 CXC2998 30 Detach Grille Assy CXC2569 CXC2570 CXC2571 55 Sub Grille Assy CXC3738 CXC3737 CXC3736
56
DEH-P860MP/XN/UC
7
8
E
F
13
1234

2.4 EXTERIOR(2)

1
1
A
6
41
2
2
40
2
9
9
7
39
B
42
10
45
C
C
11
13
43
19
39
20
21
5
5
21
5
30
36
28
D
33
32
23
35
46
31
24
38
25
29
A
A
(1/2)
26
15
B
(1/2)
23
D
20
4
F
18
22
14
34
37
16
17
14
2
E
3
F
D
CDC
F
(
14
DEH-P860MP/XN/UC
1234
5678
(1) EXTERIOR(2) SECTION PARTS LIST
Mark No. Description Part No.
1 Screw BMZ26P060FZK 2 Screw BSZ26P060FTC 3 Screw(M2.6x14) CBA1632 4 IC(IC301) PAL007A 5 Transistor(Q742,861,871) 2SD2396
6 Cord Assy CDE7701 7 Fuse(10A) CEK1136 8 ••••• 9 Cap CNS1472 10 Cord Assy See Contrast table(2)
11 Flat Cable CDE7468 12 ••••• 13 Cord Assy CDE7626 14 Earth Plate CND2171 15 Insulator CNM8659
16 Insulator CNM8790 17 Cushion CNM9126 18 FM/AM Tuner Unit CWE1646 19 Tuner Amp Unit See Contrast table(2) 20 Screw BMZ26P200FTC
21 Screw BSZ26P080FTC 22 Antenna Cable(CN402) CDH1336 23 Clamper CEF1033 24 Plug(CN932) CKM1278
Mark
No. Description Part No.
25 Connector(CN351) CKM1389
26 Plug(CN571) CKS-786 27 ••••• 28 Connector(CN702) CKS3126 29 Connector(CN101) CKS3408 30 Connector(CN701) CKS3837
31 Connector(CN931) See Contrast table(2) 32 Connector(CN561) CKS4571 33 Connector(CN801) CKS4811 34 Holder(CN401) CNC5399 35 Holder CND2040
36 Holder CND2041 37 Holder CND1054 38 Heat Sink CNR1729 39 Cap CNV6727 40 Resistor RS1/2PMF102J
41 Case Unit CXC3476 42 CD Mechanism Module(S10CODE)CXK5677 43 Screw ISS26P055FTC 44 ••••• 45 Fan Motor(M561) CXM1288
46 Sheet CNM8789
A
B
C
(2) CONTRAST TABLE
DEH-P860MP/XN/UC DEH-P8600MP/XN/UC, and DEH-P8650MP/XN/ES are constructed the same except f or the following:
Mark NO Description DEH-P860MP/XN/UC DEH-P8600MP/XN/UC DEH-P8650MP/XN/ES
10 Cord Assy CDE7436 CDE7437 CDE7436 19 Tuner Amp Unit CWM9266 CWM9267 CWM9268 31 Connector(CN931) CKS4124 CKS4124 Not used
D
E
56
DEH-P860MP/XN/UC
F
7
8
15
1234

2.5 CD MECHANISM MODULE

42
A
13
5
13
5
81
34
5
15
22
E
F
93
13
A
B
44
5
B
1
54
C
52
53
13
D
86
86
82
83
4
37
71
4
51
29
1
73
50
72
10
1
I
76
B
55
4
36
4
1
18
2
24
47
7
C
64
2
1
61
2
M
1
23
87
75
E
63
57
62
58
1
G
L
1
N
R
1
1
2
40
1
56
D
O
16
P
1
33
1
P
19
J
12
3
20
39
1
69
30
2
21
M
D
79
2
1GEM1024 2GEM1045 3GEM1035
E
92
26
G
68
28
I
H
28
45
J
38
23
K
59
49
F
Q
A
27
H
77
90
48
8
67
17
78
25
70
60
80
N
L
K
43
46
6
60
11
89
10
14
74
R
31
41
85
C
91
F
D
3
94
65
1
2
85
66
35
O
31
Q
14
85
16
DEH-P860MP/XN/UC
1234
5678
Mark
No. Description Part No.
1 CD Core Unit(S10WMACODE2)CWX2953 2 Connector(CN101) CKS4182 3 Connector(CN901) CKS4017 4 Screw BMZ20P035FTC 5 Screw BSZ20P040FTC
6 Screw(M2x4) CBA1362 7 Screw(M2x3) CBA1511 8 Screw(M2x3) CBA1527 9 ••••• 10 Washer CBF1038
11 Washer CBF1060 12 Spring CBH2390 13 Spring CBH2606 14 Spring CBH2607 15 Spring CBH2608
16 Spring CBH2609 17 Spring CBH2610 18 Spring CBH2735 19 Spring CBH2612 20 Spring CBH2613
21 Spring CBH2614 22 Spring CBH2615 23 Spring CBH2616 24 Spring CBH2617 25 Spring CBH2620
26 Spring CBH2621 27 Spring CBH2641 28 Spring CBH2642 29 Spring CBH2643 30 Spring CBH2659
31 Spring CBH2688 32 ••••• 33 Shaft CLA4441 34 Frame CNC9962 35 Frame CNC9963
36 Bracket CNC9966 37 Bracket CND1895 38 Arm CNC9968 39 Arm CND1909 40 Lever CND2032
41 Lever CNC9984 42 Sheet CNM8134 43 Collar CNV7798 44 Guide CNV7799 45 Arm CNV7800
No. Description Part No.
Mark
51 Gear CNV7208 52 Gear CNV7209 53 Gear CNV7210 54 Gear CNV7211 55 Gear CNV7212
56 Rack CNV7214 57 Arm CNV7215 58 Arm CNV7216 59 Guide CNV7217 60 Roller CNV7218
61 Gear CNV7219 62 Arm CNV7221 63 Arm CNV7220 64 Arm CNV7222 65 Damper CNV7313
66 Damper CNV7314 67 Arm CNV7341 68 Arm CNV7342 69 Guide CNV7360 70 Guide CNV7361
71 Holder CNV7437 72 Arm CNV7805 73 Gear CNV7595 74 Damper CNV7618 75 Motor Unit(M1) CXB6007
76 Chassis Unit CXC2318 77 Screw Unit CXB8729 78 Gear Unit CXC2397 79 Arm Unit CXC2316 80 Arm CND1896
81 Arm CND1894 82 Motor Unit(M2) CXB8933 83 Bracket CNC9985 84 ••••• 85 Screw(M2x5) EBA1028
86 Screw JFZ20P020FTC 87 Screw JGZ17P022FTC 88 ••••• 89 Washer YE20FTC 90 Pickup Unit(P9.9MP3)(Service) CXX1805
91 Screw IMS26P030FTC 92 Spring CBL1635 93 Clamper CNV7197 94 Connector(CN902) CKS2193
A
B
C
D
E
46 Rack CNV7199 47 Holder CNV7201 48 Holder CNV7202 49 Arm CNV7203 50 Gear CNV7207
56
DEH-P860MP/XN/UC
F
7
8
17
U
B
S
2
8
2
D
5
D
Q
V
Q
1234

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

3.1 BLOCK DIAGRAM

A
LPF
IC 1
3.3V
ROM_VDD
CF52
CF51
VDD_3.3
VDD
SL
3.3V
VDD_3.3
VCC
DI
IC 5
5V 3.3V
IC 4
3.3V 2.5V
CK
NC
CE1
2.5V
DO
NCNCNC
NC
IC 2
2.5V
DET,
FM MPX
3
IC 401
NJM2391DL1-33
TUNER AMP UNIT
A
FM/AM TUNER UNIT
ANTENNA
B
1 2 3
CN402
1
3
AM ANT
FM ANT
ATT
ATT
ANT adj
FMRF
FMRF
RF adj
7 6 13 5 10 9 8 11 14 18 19 20 21
WC
CE2
IC 3 EEPROM
5.0V
OSC
MIXER, IF AMP
T51
RFGND
OSCGND
DGND
212 1522 16 4 17
AUDIOGNDNCVCC
Rch
24
Lch
23
TUNER 3V REGULATOR
1
TUN8V
BUS+L BUS-L
CN101
7
11
8 5 1
BU
MCKR
IC 12
DOUT,LRCK,BCK
TUN L
BUSL­BUSL+
DSPOUT,DSPCK,E
DPDT
33
MUTE
KEYAD
KEYD
SYSPW
DALMON
FLPILM
ROT0
ROT1
ILMPW
DSPPW
SWVDD
OELPW
TC74VHCT12
13
10
4
TC7SH0
85
92
39
1
68
40
36
35
41
2
38
20
IC 801(1/
1211
98
B.UP
B.
G
G
IC 80
CD CORE UNIT(S10WMACODE2)
C
D
PICKUP UNIT (P9.9MP3)(SERVICE)
LASER DIODE
HOLOGRAM
UNIT
FOCUS ACT.
TRACKING ACT.
MONITOR
DIODE
M1
M
SPINDLE MOTOR
M2
LOADING/CARRIAGE
MOTOR
M
E
D
CN902
MCK
CN901
DOUT,LRCK,
BCK
BRST,BRXEN,BSRQ
BDATA,BSCK
VD
VDCONT
CD3VON
VDD
2
VDD
TX
RX
VD
VD2
Q101
AC,BD
F,E
S904 12EJ
V3R3D
142
LD
143
PD
RF AMP, CD DECODER, MP3 AND WMA DECODER DIGITAL SERVO/DATA PROCESSOR
TD/FD
SD/MD
12
FOP
13
TOP
CD
DRIVER
16
SOP
LOEJ
15
SOM
18
LCOP
CONT
17
LCOM
IC 301
BA5835FM
IC 203
S903
DSCSNS
S901
HOME
1
S905
8EJ
3
NJM2391DL1-33
IC 201
UPD63761GJ
COMPUTER
53
22
LOEJ
9
47
CONT
4
CLAMP
32
12EJ
31
8EJ
30
DSCSNS
97
HOME
VD2
CN101
LD-
15
15
MD
5
5
FOP
FO+
1
1
TO+
TOP
4
4
LD+
14
14
S902
CLAMP
V3R3D
3.3V REGULATOR
V1R5
5
IC 501
S-L2980A15MC-C6A
1,3
V3R3D
X702
X1
MICRO
IC 701
PE5423A
3VDD
34 XTAL
LRCK
1312
X2
25
FTxD
26
FRxD
49
VDCONT
46
CD3VON
3.3V REGULATOR
3
IC 703
S-812C33AUA-C2N
CN702
MCK
1
1
CDTX
4
4
CDRX
3
3
CN701
VD
3
21
4
20
VDCONT
5
19
CD3VON
23
1
19
5
VD2
2
22
B
MICROPHONE
MIC
MIC 521
MCKRQ
VDD
MCKRQ
A
DOUT,LRCK,BCK
IC 522
2
NJM4558V
BRST,BRXEN,BSRQ
BDATA,BSCK
Q743
Q744
Q742
Q571
7
2
Q741
IC 521
NJM4558V
Q572
X601
93
7
B.UP
11
13
B.UP
ASLIN
XOUT
XIN
SYSTEM CONTROLLER
IC 601(2/2)
PD5928A
1.5V REGULATOR
54
A
CDRX
44 43
51
50
CDTX
FLPPW
FLPCLS FLPOPN
FCLSSW
FOPENSW
KYDT
34
GDTC1
TC74VHCT125AFT
GDTC2
CN571
4
M571
FLAP
M
MOTOR
SWITCH UNIT
B
F
18
DEH-P860MP/XN/UC
S1
CLOSE
OPEN
S2
M561
FAN
MOTOR
OUT1
5
OUT2
4
FCLSSW
3
FOPNSW
2
1
CN561
2
M
1
3
14
BA6288FS
Q561
IC 571
5
11
6
B
Q562
B.UP
SYSPW
1234
CN101
L
7
11
DOUT,LRCK,BCK
TUN L BUSL-
BUSL+
DSPOUT,DSPCK,EVOLCS
SYSPW
DALMON
FLPILM
CONTROLLER
601(2/2)
DSPPW
5928A
SWVDD
OELPW
DPDT
33
DTC1
AFT
10
DTC2
8 5 1
BUS-
BUS+
MCKRQ
IC 122
4
TC7SH08FU
Q281
85
MUTE
92
KEYAD
39
KEYD
1
68
40
36
ROT0
35
ROT1
B.UP
41
ILMPW
2
38
B.UP
20
GDTC1
IC 801(1/2)
TC74VHCT125AFT
13
GDTC2
1211
IC 801(2/2)
98
Q101
IP-BUS DRIVER
5
IC 101
6
HA12240FP
8 IPPW
3V 5V
IC 662
TC74VHC08FT
DRDY3,RDY3,
DSPSO3
1
16
9 8
33
SOURCE SELECTOR
KEYAD
KEYD
B.UP
Q852
Q853
DSPPW
VDD
Q842
1
2
5
4
5678
A
Q352
Q353
Q354
SWL
RL
FL
CN351
FU351
9
10
5
6
1
2
3A
SUB WOOFER L
REAR L
FRONT L
B
CN932
B.UP
Q921
1
AUDIO 8V
B.UP
3 5 23 21
Q862
CN931
FUSE
1
10A
1K(1/2W)
5
1K(1/2W)
3
8
2
10 12
9
11
4
B.UP
A:DEH-P860MP/XN/UC B:DEH-P8600MP/XN/UC C:DEH-P8650MP/XN/ES
A,B
BACK UP
ACC
ILL
TEL MUTE
GND
B.REM
C
D
WIRED REMOTE CONTROL
KEYBOARD UNIT
C
E
13
X1801
11
F
CN1902
1
MICROPHONE
2 3
INPUT
24
A,B
SYSPW
Q851
3
6
1 2
Q832
Q841
B.UP
TX RX
Q831
AK7730VT
25
AEQMIC
DSENS
RST1
DRDY,RDY,
DSP
IC 121
X121
DSPIN
26
DAC5V
CN801
SWVDD
OELPW
AEQGND
ce@
CE1 DO DI CK
ILM+B
Q651
RST1
80
ASENBO
28
TX
27
RX
SYSTEM CONTROLLER
79
IPPW
69
tunpce@
70
TUNPCE1
98
TUNPDI
99
TUNPDO
100
TUNPCK
95
SL
RQ3,DSPCK3,
DSPOUT3,DSPCS3
47
48
SW,LRCKO,
BCKO
DAC
F,LRCKO,
BCKO
R,LRCKO,
BCKO
IC 281 PML011A
DAC 5V REGULATOR
5
IC 961
NJM2872F05
Q501
VDD
11
11 10
10
7
7
8
8
5
5
9
9
17
17
DPDT
13
13
RST
14
14
12
12 15
15
RESET
1
IC 651
S-80835CNMC-B8U
10
reset
IC 601(1/2)
PD5928A
IC 661
7
IC 183
7
IC 181
7
7
IC 182
IC181-183
:PCM1742KE
1
CN1903
ILLUMINATION
ILM+B
SWVDD
OPT IN
OELB
OEL+B
AEQMIC DSENS
DPDT
S1909
RST
RESET
KYDT AEQGND
2
VDD
22
PEE
32
DSPMOD
81
isens
8
TELIN
68
DALMON
73
BSENS
72
ASENS
RQ,DSPCK,
DSPOUT,DSPCS
5V 3V
TC74VHC08FT
21
NJM2112V
44
IC 261
IC 213
35
31
LPF
IC 211
39
31
37
31
IC 212
IC211-213
:NJM4580V
ELECTRONIC VOLUME
AUDIO 8V
AUTO-EQ
AEQMIC
S1912 ROT0 ROT1
SOURCE/VOLUME
3.3V REGULATOR
IC 1802
4
S-818A33AUC-BGN
4
IC 1901
5
1
RS-140
REMOTE CONTROL
SENSOR
27
28
Q1906
BZ601
BUZZER
MODE
A,C
Q502
15
REM
DPDT
KYDT
VDD
S551 STD
NW
SWL
25
29
27 17
AUTOEQ
AUTOEQ
97
FL
kd!
ks!
AVCC
RL
37
23
S1913
SWL
RL
FL
B.UP
TUN8V
3.3V
FLASH MEMORY
IC 1807
VCC
PD6468A
FONT ROM
IC 1806
VCC
PD8124A
60
VCC114VCC2
ROT1
ROT2
16 17
MULTI CONTROL
Q351
VDD
1/2VCC REGULATOR
7
4.7V
IC262 NJM4558MD
Q871
1
Q451
15
RY/by
26
ce
12
ce
OEL CONTROLLER/
KEY CONTROLLER
IC 1805
PD5943A
OEL+B
SWVDD
CN1802
8
IC 321
10
PA2028A
12
VDD REGULATOR
Q881
BACKUP SENSE
Q911
ACC SENSE
6 5
12
FLIN
14
RLIN
22 4
MUTE
Q301
Q872
Q873
SWVDD
IC 1808
TC7WH32FK
7
3
OEL+B
VDD
11 1278
OEL MODULE
17
15
13
MUTE
Q882
ACC
Q891
TELEPHONE MUTE
AUDIO 3V REGULATOR
D3V
A3V
NJM2391DL1-33
POWER AMP
IC 301
PAL007A
STBYMUTE
AUDIO 8V REGULATOR
AUDIO 8V
B.UP
SYSPW
DSPPW
Q1806
2 6 5
48
4
rs!36cs)
flbusy
CKD,LS,D0_L,D1_L, CD_DATA,CKC
MUTE
ILM SENSE
VDD
3
IC 941
6,20
FL-
FL+
RL-
RL+
B.REMOTE
25
Q861
SYSPW
KEYAD
KEYD
KEY MATRIX
KEY DATA
XIN
XOUT
56
DEH-P860MP/XN/UC
7
8
19
1234

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)

Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
A
"ELECTRICAL PARTS LIST".
A-a
2.5V
2.5V
A-a A-b
A-a
A-a
A-b
A-b
Large size
SCH diagram
Guide page
Detailed page
TUNER AMP UNIT
A
: SIGNAL LINE
P
: POWER SUPPLY LINE
B
2.5V
2.5V
2.5V
2.5V
1.65V
1.65V
1.65V
C
111098
7
2143
65
D
E
F
A B
20
M561
FAN MOTOR
CXM1288
8.4V
P
P
P
CN901
D
P
P
CN902
5.5V
6.8V
DSP
ANTENNA CABLE
FM/AM TUNER UNIT
3.3V
P
P
P
231
M
M571
FLAP MOTOR
CXC2204
CSN1051
S1 CLOSE
CSN1052
S2 OPEN
B
SWITCH UNIT
C
CN1903
DEH-P860MP/XN/UC
1234
5678
A
A-b
NOTE :
4.7V
4.7V
4.7V
4.7V
TUNER(30%):-19.97dBs
IP-BUS: +1.66dBs
CD: +2.55dBs
4.7V
4.7V
3.3V
5.0V
TUNER(30%):-7.97dBs
IP-BUS: +7.66dBs
CD: +7.55dBs
Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors.
Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors.
Decimal points for resistor and capacitor fixed values are expressed as :
2.2 2R2
0.022 R022
B
4.3V
4.7V
3.5V
>
1.65V
6.9V
6.9V
6.9V
6.9V
8.5V
5.3V
8.3V
14.3V
SUBWOOFER R CH
SUBWOOFER L CH
REAR R CH
REAR L CH
FRONT R CH
FRONT L CH
A,C
TUNER(30%): +2.53dBs
IP-BUS:+18.16dBs
CD:+18.05dBs
B
TUNER(30%): -0.47dBs
IP-BUS:+15.16dBs
CD:+15.05dBs
TUNER(30%):+18.03dBs
IP-BUS:+33.66dBs
CEK1136
10A
>
P
1K(1/2W)
P
1K(1/2W)
P
CD:+33.55dBs
BACKUP GND ILL B.REM ACC
TEL RL FL RL+ FL+ RR FR RR+ FR+
C
D
C
CN1903
9.5V
10.0V
P
P
P
The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
WIRED REMOTE CONTROL
E
F
A
56
DEH-P860MP/XN/UC
7
8
21
1234
A
A-b
1
2
3
1.65V
1.65V
1.65V
4
B
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
C
A-b A-a
A-a
D
M561
CXM1288
FAN MOTOR
8.4V
E
TUNER AMP UNIT
: SIGNAL LINE
: POWER SUPPLY LINE
F
A
P
2143
65
7
111098
A-a
22
1234
DEH-P860MP/XN/UC
9
5678
DSP
5
6
P
P
P
A-b
A
CN1903
C
B
C
B
SWITCH
UNIT
CSN1052 S2 OPEN
CSN1051
S1 CLOSE
231
A-b
8.4V
5.5V
6.8V
M
M571
A-a
A-a
CXC2204
FLAP MOTOR
D
CN902
3.3V
E
CN901
P
P
P
P
D
P
FM/AM TUNER UNIT
56
DEH-P860MP/XN/UC
ANTENNA CABLE
7
A-a
8
F
B
23
1234
A
REAR
L CH
SUBWOOFER
L CH
REAR
R CH
R CH
FRONT
R CH
FRONT
L CH
IP-BUS:+18.16dBs
TUNER(30%): +2.53dBs
A,C
>
CD:+18.05dBs
CD:+15.05dBs
IP-BUS:+15.16dBs
B
TUNER(30%): -0.47dBs
SUBWOOFER
Decimal points for resistor
and capacitor fixed values
are expressed as :
2.2 2R2
0.022 R022
B
8.5V
C
6.9V
Symbol indicates a resistor.
No differentiation is made between chip resistors and
discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.
6.9V
6.9V
6.9V
A-b A-a
NOTE :
D
3.3V
5.0V
E
CD: +7.55dBs
IP-BUS: +7.66dBs
TUNER(30%):-7.97dBs
3.5V
4.3V
CD: +2.55dBs
IP-BUS: +1.66dBs
TUNER(30%):-19.97dBs
4.7V
4.7V
4.7V
4.7V
4.7V
4.7V
4.7V
1.65V
F
A-b
24
1
2
3
DEH-P860MP/XN/UC
4
1234
5678
RR
RR+
FR
BACKUP
GND
ILL
CD:+33.55dBs
IP-BUS:+33.66dBs
TUNER(30%):+18.03dBs
10A
CEK1136
1K(1/2W)
>
P
P
B.REM
ACC
1K(1/2W)
P
RL
RL+
FL
TEL
FR+
FL+
A
14.3V
8.5V
5.3V
WIRED REMOTE CONTROL
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
The > mark found on some component parts indicates
B
C
A-b A-a
8.3V
D
9.5V
5
DEH-P860MP/XN/UC
56
E
10.0V
F
6
7
A-b
25
8
1234

3.3 KEYBOARD UNIT

A
REMOTE CONTROL
SENSOR
RESET
B
CN801
A
C
D
5.2V
9.9V
9.1V
OPEN
MICROPHONE INPUT
MULTI-CONTROL
SOURCE/VOLUMEEQ DISP
E
F
5
4
321
CLOCK
BAND/ESC6
C
26
1234
DEH-P860MP/XN/UC
5678
A
KEYBOARD UNIT
C
FONT ROM
B
OEL CONTROL/ KEY CONTROL
C
D
E
OEL MODULE
MXK8200
DEH-P860MP/XN/UC
56
F
C
7
8
27
Loading...
+ 63 hidden pages