Pioneer DEH-P780MP User Manual

Antenna jack

This product

IP-BUS input (Blue)

Connecting cords with RCA pin plugs (sold separately)

Power amp

(sold separately)

System remote control

Front speaker Front speaker

Left Right

Perform these connections when using the optional amplifier.

≠

Yellow/black If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections.

Yellow To terminal always supplied with power regardless of ignition switch position.

Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF.

Orange/white To lighting switch terminal.

Black (ground) To vehicle (metal) body.

Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC).

Front speaker Front speaker

With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.

Rear speaker

Gray

Gray/black

Violet

Violet/black

White

White/black

Green

Green/black

Rear speaker

Power amp

(sold separately)

Power amp

(sold separately)

Subwoofer Subwoofer

≠

Rear speaker Rear speaker

IP-BUS cable

Multi-CD player (sold separately)

15 cm (5-7/8 in.)

Subwoofer output (SUBWOOFER OUTPUT)

Rear output (REAR OUTPUT)

Front output (FRONT OUTPUT)

23 cm (9 in.)

15 cm (5-7/8 in.)

Jack for the Wired Remote Control Adaptors Please see the Instruction Manual for the Wired Remote Control Adaptors (sold separately).

Fuse resistor

Fuse (10 A)

Fuse resistor

AUX input jack (3.5 ø)

Use a stereo mini plug cable to connect with auxiliary equipment.

DEH-P780MP

This product conforms to CEMA cord colors. Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA.

INSTALLATION MANUAL

Printed in Thailand Imprimé en Thaïlande

<CRD4086-A/N> UC

Connecting the Units <ENGLISH>

Note:

• This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery voltage.

MANUEL D’INSTALLATION

• To avoid shorts in the electrical system, be sure to disconnect the ≠ battery cable before beginning installation.

• Refer to the owner’s manual for details on connecting the power amp and other units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body.

• Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short.

• Do not shorten any leads. If you do, the protection circuit may fail to work when it should.

• Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

• When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse holder.

• Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right ≠ speaker leads are common.

• Speakers connected to this unit must be highpower with minimum rating of 50 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke or becoming damaged.

• When this product’s source is switched ON, a control signal is output through the blue/white lead. Connect to an external power amp’s system remote control or the car’s Auto-antenna relay control terminal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal.

• When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal. Likewise, do not connect the blue/white lead to the power terminal of the auto-antenna. Such connection could cause excessive current drain and malfunction.

• To avoid a short-circuit, cover the disconnected lead with insulating tape. Insulate the unused speaker leads without fail. There is a possibility of a short-circuit if the leads are not insulated.

• To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. Connect the connectors of the same colors correctly.

• If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours. (Fig.1)

• The black lead is ground. Please ground this lead separately from the ground of high-current products such as power amps. If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire.

• Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the same function.

No ACC positionACC position

Fig. 1

Fig. 2

ubber bush

Installation <ENGLISH>

Note:

• Before making a final installation of the unit, temporarily connect the wiring to confirm that the connections are correct and the system works properly.

• Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it overheats, so don’t install the unit anywhere hot — for instance, near a heater outlet.

• If installation angle exceeds 60° from horizontal, the unit might not give its optimum performance. (Fig. 3)

60°

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 4)

Holder After inserting the holder into the dashboard, then select the appropriate tabs according to the thickness of the

Dashboar

dashboard material and bend them. (Install as firmly as possible using the top and bottom tabs. To secure, bend the tabs 90 degrees.)

Fig. 3

Removing the unit (Fig. 5) (Fig. 6)

Frame

To remove the frame, extend top and bottom of the frame outwards in order to unlock it. (When reattaching the frame, point the side with a groove downwards and attach it.)

• It becomes easy to remove the frame if the front panel is released.

Insert the supplied extraction keys into the unit, as shown in the figure, until they click into place. Keeping the keys pressed against the sides of the unit, pull the unit out.

Fig. 5

Fig. 6

DIN Rear-mount

Installation using the screw holes on the side of the unit

1. Remove the frame. (Fig. 7)

Frame

To remove the frame, extend top and bottom of the frame outwards in order to unlock it. (When reattaching the frame, point the side with a groove downwards and attach it.)

• It becomes easy to remove the frame if the front panel is released.

2. Fastening the unit to the factory radio mounting bracket. (Fig. 8) (Fig. 9)

Select a position where the screw holes of the bracket and the screw holes of the head unit become aligned (are fitted), and tighten the screws at 2 places on each side. Use either truss screws (5 × 8 mm) or flush surface screws (5 × 9 mm), depending on the shape of the screw holes in the bracket.

Fixing the front panel

If you do not operate the removing and attaching the front panel function, use the supplied fixing screw to fix the front panel to this unit.

Fixing screw

Fig. 10

Fig. 7

Fig. 8

cre

Factory radio mounting bracket

Fig. 4

Screw

Dashboard or Console

Fig. 9

+ 2 hidden pages