
Expander Modules
Delayed
PZE 5V
Expander module in accordance with
VDE 0113-1, 11/98, EN 60204-1,
12/97, and IEC 204-1, 11/98 to
increase the number of safety
contacts available.
Features
● Delay-on de-energisation can be
set via the rotary switch
● Delay-on de-energisation is
effective after power failure
Approvals
PZE 5V
●
●
Technical Details PZE 5V
Electrical Data
Supply Voltage AC: 24, 42, 110, 120, 230, 240 V
DC: 24 V
Tolerance 85 ... 110 %
Power Consumption Approx. 3.5 W/5 VA
Residual Ripple DC 20 %
Total Current max. 40 A
Switching Capabilty in accordance with
EN 60947-4-1, 10/91 AC1: 240 V/8 A/2000 VA
400 V/5 A/2000 VA
DC1: 24 V/8 A/200 W
EN 60947-5-1, 10/91 AC15: 230 V/5 A; DC13: 24 V/7A
(DC13: 6 cycles/min.)
Output Contacts 4 safety contacts (N/O),
1 auxiliary contact (N/C)
Contact Fuse Protection
(EN 60947-5-1, 10/91) 10 A quick or 6 A slow
Times
Delay-on Energisation
Time range 0.5 ... 3 s AC: 0.2/0.4/0.8/1.2 s
DC: 0.08/0.15/0.3/0.45 s
Time Range 2 ... 8 s AC: 1/2/3/4 s
DC: 0.33/0.66/1/1.3 s
Delay-on De-energisation
Time range 0.5 ... 3 s 0.5/1/2/3 s
Time range 2 ... 8 s 2/4/6/8 s
Recovery Time Delay-on de-energisation + delay-on
energisation
Mechanical Data
Torque Setting on Connection Terminals 1.2 Nm (screws)
Maximum Cross Section of 2 x 2.5 mm
External conductors Single-core or multi-core with
crimp connectors
Dimensions (H x W x D) 87 x 135 x 110 mm
Weight
Range 0.5 ... 3 s AC: 670 g, DC: 570 g
Range 2 ... 8 s AC: 720 g, DC: 620 g
2
●
Description
● 135 mm, P-75 housing, DIN-Rail
mounting
● Positive-guided relay outputs:
– 4 safety contacts (N/O)
– 1 auxiliary contact (N/C)
● Connection for feedback control
loop
● Delay-on energisation and delayon de-energisation can be
programmed
● Single or dual-channel operation
● 2 versions available with different
time ranges.
Function Description
PZE 5V is used to increase
the number of safety contacts
available and the timed delay
switching of an E-STOP command
for
● E-STOP relays
● Safety gate monitors
● Two-hand relays
All base units must have a feedback
control loop.
NSG-D-2-096-02/02
6

Expander Modules
Delayed
PZE 5V
Internal Wiring Diagram
U
B
A1
(L+)
F1
~
G1
A2
(L-)
+
Input circuit
U
K1
=
K2
U
Input circuit
External Wiring
● Example 1
Single-channel operation
L1
PE
X1
X2
(Y1)
(Y2)
Y1
K1
C1 C2 C3 C4
C5 C6 C7 C8
K2
Y2
A1
X1
(+)
Time ranges
132
45
(-)
X2
K1
K2
6
1314232433
Feedback
control loop
X1 X2
43
Safety
contacts
13 23 33 51
14
24 34 5244
1
Y1
43
2
Auxiliary
contacts
3
6
Base unit
14
1323
24
N
● Example 2
Dual-channel operation
L1
PE
X1
X2
(Y1)
(Y2)
Base unit
14
1323
24
PZE 5V
K1
U
A1
X1
X2
(+)
PZE 5V
K1 K2UU
445152
A2
Y2
56
Y1
Y2
4
12
5
3
64
(-)
51
A2
52
(-)
K2U
(-)
34
131423
2433344344
N
NSG-D-2-096-02/02

Expander Modules
Delayed
PZE 5V
General Technical Data
Unless stated otherwise in the technical details for the specific unit
Electrical Data
Frequency Range AC 50 ... 60 Hz
Residual Ripple DC 160 %
Contact Material AgSnO
Continuous Duty 100 %
Environmental Data
EMC EN 50081-1, 01/92, EN 50082-2, 03/95
Vibration in accordance with Frequency: 10 ... 55 Hz,
EN 60068-2-6, 04/95 Amplitude: 0.35 mm
Climatic Suitability DIN IEC 60068-2-3, 12/86
Airgap Creepage DIN VDE 0110 part 1, 04/97
Ambient Temperature -10 ... +55 °C
Storage Temperature -40 ... +85 °C
Mechanical Data
Torque Setting on Connection Terminals 0.6 Nm (screws)
Mounting Position Any
Housing Material Thermoplast Noryl SE 100
Protection Mounting: IP 54
2
Housing: IP 40
Terminal Range: IP 20
The units were tested in accordance with the relevant standards current at
the time of development.
Order References
Type t U
PZE 5V 3 s 24 V DC 474 965
PZE 5V 3 s 24 V AC 474 950
PZE 5V 3 s 42 V AC 474 951
PZE 5V 3 s 110 V AC 474 954
PZE 5V 3 s 120 V AC 474 956
PZE 5V 3 s 230 V AC 474 958
PZE 5V 3 s 240 V AC 474 959
PZE 5V 8 s 24 V DC 474 985
PZE 5V 8 s 24 V AC 474 970
PZE 5V 8 s 42 V AC 474 971
PZE 5V 8 s 110 V AC 474 974
PZE 5V 8 s 230 V AC 474 978
PZE 5V 8 s 240 V AC 474 979
B
Order No.
6
NSG-D-2-096-02/02