Pilz PSSu E S 2DOR 2 User Manual

Operating Manual PSSu E S 2DOR 2(-T )

Operating Manual PSSu E S 2DOR 2(-T)

PSSu E S 2DOR 2(-T)

Decentralised system PSSuniversal I/O

Operating Manual — No. 22077-EN-04

This document is a translation of the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for internal purposes.

Suggestions and comments for improving this documentation will be gratefully received.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®, SafetyEYE®,
SafetyNET p®, the spirit of safety® are registered and protected trademarks of
Pilz GmbH & Co. KG in some countries.

SD means Secure Digital.

Preface

Contents

Contents

Contents Page

Chapter 1 Introduction

1.1 Validity of documentation 1-1

1.1.1 Retaining the documentation 1-1

1.1.2 Terminology: System environment A and B 1-1

1.2 Overview of documentation 1-2

1.3 Definition of symbols 1-3

Chapter 2 Overview

2.1 Module structure 2-1

2.1.1 Module features 2-1

2.2 Front view 2-2

Chapter 3 Safety

3.1 Intended use 3-1

3.2 Safety regulations 3-3

3.2.1 Use of qualified personnel 3-3

3.2.2 Warranty and liability 3-3

3.2.3 Disposal 3-3

Chapter 4 Function description

4.1 Module features 4-1

4.1.1 Integrated protection mechanisms 4-1

4.1.2 Function description 4-1

4.1.3 Reaction times 4-1

4.2 Configuration 4-2

4.2.1 Addresses in the process image 4-2

Chapter 5 Installation

5.1 General installation guidelines 5-1

5.1.1 Dimensions 5-1

5.2 Installing the base module 5-3

5.3 Inserting and removing an electronic mod­ule

5.3.1 Inserting an electronic module 5-4

5.3.2 Removing an electronic module 5-4

5.3.3 Changing an electronic module during op­eration

5-4

5-5

Chapter 6 Wiring

6.1 General wiring guidelines 6-1

6.1.1 Mechanical connection of the base mod­ules

6.2 Terminal configuration 6-4

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

6-1

1

Contents

6.3 Connecting the module 6-5

Chapter 7 Operation

7.1 Messages 7-1

7.2 Display elements 7-2

7.2.1 Display elements for module diagnostics 7-2

7.2.2 Display elements for output status 7-2

Chapter 8 Technical details

8.1 Technical details 8-1

8.2 Order reference 8-4

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany

2

Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

1 Introduction

1.1 Validity of documentation

11000IntroductionIntroduction1-1.1Validity of docume ntation1100Validity of documenta tion1-][BA Einf Gültigkeit_(T)

This documentation is valid for the product types PSSu E S 2DOR 2 and

Einf Einleitung

Bestimm_Verwend_ Zusatz-(T)

1.1.1 Retaining the documentation

Retaining the documentation1-Einf Aufbewahren

PSSu E S 2DOR 2-T. It is valid until new documentation is published.

This operating manual explains the function and operation, describes
the installation and provides guidelines on how to connect the product.

The module PSSu E S 2DOR 2-T is suitable for use where there are in­creased environmental requirements (see Technical Details).

This documentation is intended for instruction and should be retained
for future reference.

1.1.2 Terminology: System environment A and B

Terminology: System environment A and B1-][BA Einf Begriffsdefinition Sys A + B

The PSSu system can be used in two different system environments.
The module's application area is described in the chapter "Intended
Use" of the manual.

The distinction is made between

 PSSu in system environment A
 PSSu in system environment B

The distinction is based on the application area of the PSSu system.

PSSu in system environment A may be used in the

 Decentralised system PSSu I/O with SafetyBUS p
 Decentralised system PSSu I/O with ST fieldbuses such as CANopen,

DeviceNet

 Not in the automation system PSS 4000

PSSu in system environment B may be used in the

 Automation system PSS 4000, e.g. with the

– Decentralised system PSSu I/O with SafetyNET p
– Control system PSSu PLC
– Control system PSSu multi

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

1-1

1 Introduction

1.2 Overview of documentation

1.2Overview of documentation1200Overview of documentation1-][BA Einf Übersicht E-Modul

1 Introduction

The introduction is designed to familiarise you with the contents, struc­ture and specific order of this manual.

2 Overview

This chapter provides information on the product's most important fea­tures.

3 Safety

This chapter must be read as it contains important information on safety
and intended use.

4 Function Description

This chapter describes the product's individual components.

5 Installation

This chapter explains how to install the product.

6 Wiring

This chapter describes the product's wiring.

7 Operation

This chapter explains the display elements and advises on what to do if
a fault occurs.

8 Technical Details

This chapter contains the product's technical details and order refer­ence.

1-2

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

1 Introduction

1.3 Definition of symbols

1.3Definition of symbols1300Definition of symbols1-Einfhrung Zeichen

Information that is particularly important is identified as follows:

DANGER!

This warning must be heeded! It warns of a hazardous situation
that poses an immediate threat of serious injury and death and
indicates preventive measures that can be taken.

WARNING!

This warning must be heeded! It warns of a hazardous situation
that could lead to serious injury and death and indicates preven­tive measures that can be taken.

CAUTION!

This refers to a hazard that can lead to a less serious or minor
injury plus material damage, and also provides information on
preventive measures that can be taken.

NOTICE

This describes a situation in which the unit(s) could be damaged
and also provides information on preventive measures that can
be taken. It also highlights areas within the text that are of partic­ular importance.

INFORMATION

This gives advice on applications and provides information on
special features.

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

1-3

1 Introduction

1-4

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

2 Overview

2.1 Module structure

22000OverviewOverview2-2.1Module structure2100Module structure2-][BA Übersicht Aufbau

A module consists of

 Electronic module and
 Base module with

The base modules are the carrier units for the electronic modules and
are used to connect the field wiring. The electronic modules are inserted
on to the base modules and determine the module's function.

Details of the base modules that can be used are available in the chapter
entitled “Intended Use”.

– Screw terminals or
– Cage clamp terminals

2.1.1 Module features

Module features2-Geraetemerkmale_Zusatz BA Einleitung

][Merkmale_Ein_Aus Ausgan g Relais ST

][Merkmale_LED Aus gang

][Merkmale_Zusatz ST-Module Sys A + B

][Geraetemerkmal_T

The product has the following features:

 2 relay contacts

– Normally open contact
–Volt-free
– Current load capacity per output: 2.0 A

 LEDs for:

– Switch status of each output
– Module error

 For standard applications in system environment A and B
 T-type:

PSSu E S 2DOR 2-T: for increased environmental requirements

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

2-1

2 Overview

2111

2212

2313

2414

Err

11

O0

12 22

13

(C)23(C)

PSSu E S
2DOR 2

11
14

PSSu E S

2DOR 2
312511
000000

001

21
O0

14O124

O1

10

1

3

4

9

8

5

6

7

11

2

12

A

B

2.2 Front view

2.2Front view2200Front view2-BA_Fron tansicht

2-2

][BA_Frontansicht Legende Diag - Stat lang

Legend:

 A: Electronic module
 B: Base module

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

 1: LED for module diagnostics
 2: Labelling strip with:

– Name of electronic module
– Order Number
– Serial number
– Hardware version number
–2D code

 3: Labelling strip for the terminal configuration on the base module
 4: Status LEDs
 5: Name of electronic module
 6: Connection level 1
 7: Connection level 2
 8: Connection level 3

2 Overview

2.2 Front view

 9: Connection level 4
 10: Square mounting holes (connection levels 1, 2, 3 and 4)

– With screw to loosen/tighten the screw terminal on base modules

with screw terminals

– With mechanism to operate the cage clamp on base modules with

cage clamp terminals

 11: Round connection holes (connection levels 1, 2, 3 and 4) for con-

necting the signal lines

 12: Mounting slot for colour marker to label the connection level (con-

nection levels 1, 2, 3 and 4)

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

2-3

2 Overview

2-4

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]