PICOBREW Z SERIES
GETTING STARTED
Quick Start
Congratulations! You are now the owner
of a PicoBrew Z Series, a professional
grade brewing appliance designed to
scale to your needs.
Each unit of your Z Series system is packaged in three boxes:
• Box #1 Heating Module
• Box #2 Brewing Ingredients Module
• Box #3 Brew Keg
(When you purchase a Z2- Z4 system you
will also receive Box #4: Power Cable.)
Instructions
are Online
For a complete set of operating
instructions, please refer to the online
manual for your Z Series brewing
machine at:
www.picobrew.com/ZManual
What’s in the Box
BOX #1
• Z Heating Module
BOX #2
• Z Brewing Ingredients Module
• Assembly Screws (8 Black, 4 Stainless)
• T20 Screw Driver
• Drip Mat
• Heating Module Power Cord
• Step Filter
• Step Filter Plug (3)
• Step Filter Lid
• Drain Tube
• Drain Tube Grommet (2)
• Adjunct Compartment
• Top Mash Screen
• Bottom Mash Screen
• Adjunct Screen
• Hop Cages, Lids and Bands (4 ea.)
• Keg Cozy
• Foam Trap (and Extra Washer)
• Party Tap
• Ethernet Cable
• Syringe
• Transfer Tube
• Bottle of Anti-Foam
• Cleaning Tubes (2)
• Dishwasher Tablet
• Dip Tube Cleaning Brush
For any questions or concerns, please
contact our customer care team at
info@picobrew.com for assistance.
Cheers!
SAVE ALL PACKAGING MATERIALS
ZN Quick Start
BOX #3 (KEG)
• Keg Seal
• Keg Seal Plug
• 3-piece Airlock
• Fast Fermentation Adapter
• Brew Keg (5 gallon)
• Metal Keg Lid
V.19.93.09400-098
Important Safety Information
• Exercise common sense while operating the Z.
• Always use the keg cozy to shield the hot
metal of the keg.
• Close supervision is needed when used
around children.
• Allow machine to fully cool before removing
or replacing parts.
• Do not operate with a frayed cord or broken
plug.
• Do not remove Step Filter from the Z unless in
pause mode or brew cycle is completed.
• The Step Filter and contents may be hot when
removing from the machine.
• Do not immerse or soak the machine.
• Make sure all hoses are connected before
starting a brewing, rinsing or cleaning cycle.
• To avoid risk of electrical shock hazard do
not disassemble the Z. There are no user
serviceable parts inside.
Z Unit Assembly
• Various surfaces can get extremely hot during
the brewing cycle, use caution when handling
the keg, hoses and components.
• Do not remove the hose clamps, hot liquid
spray may result.
• Do not remove the keg attachments while
brewing.
• Do not make any modications to your Z or any
of its components. Doing so can be dangerous,
will void your warranty, and may cause damage
to your Z or affect its performance.
• Avoid exposing your Z to rain, moisture, or
other liquids which may cause damage to your
machine or injury to you.
• Do not store your Z where it will be exposed
to below freezing temperatures as this may
damage internal components.
• Only operate your Z on completely level and
sturdy surfaces.
Pro Tip:
Insert & lightly hand-tighten all
screws before using T20 driver to
fully tighten screws.
USE STAINLESS
SCREWS IN FRONT
Setting up a Z2-Z4 System? Visit www.picobrew.com/pr/ZSeriesSetup
All rights reserved. No part of this publication may be reproduced, stored in
retrieval systems or transmitted in any form or by any means electronic or
mechanical, including, photocopying, record or any information storage and
retrieval systems, without the written permission in writing from the copyright
owners. Printed in Seattle, WA, USA
www.picobrew.com
Produced by:
PicoBrew Inc.
2121 N 35th St.
Seattle, WA 98103
© 2019 PicoBrew
Loading...