1 Technical Specifications, Connections, and Chassis
Overview2
2 Safety Instructions, Warnings, and Notes4
3 Directions for Use6
4 Mechanical Instructions9
5 Service Modes, Error Codes, and Fault Finding 11
6 Block Diagrams, Test Point Overview, and
Waveforms
Wiring Diagram16
Block Diagrams17
7 Circuit Diagrams and PWB LayoutsDiagram
Scaler Board: Power(S-A01) 22
Scaler Board: Lips & Inverter I/F(S-A02) 23
Scaler Board: Tuner(S-A03) 24
Scaler Board: Video Input 1(S-A04) 25
Scaler Board: Side AV(S-A05) 26
Scaler Board: DSUB Input(S-A06) 27
Scaler Board: DVI-D Input(S-A07) 28
Scaler Board: Scaler(S-A08) 29
Scaler Board: Flash ROM & Memory(S-A09) 30
Scaler Board: Key, IR BD & ComPair I/F(S-A10) 31
Scaler Board: ITV I/F(S-A11) 32
Scaler Board: Panel I/F(S-A12) 33
Scaler Board: Audio I/F(S-A13) 34
Scaler Board: Audio MUX(S-A14) 35
Scaler Board: Audio Amplifier(S-A15) 36
Waveform Diagram43-44
Keyboard Control Panel(K) 45
IR & LED Panel(IR) 48
Side AV Panel(AV) 51
Power Panel(P) 54
8 Alignments (incl. ComPair)57
9 Circuit Descriptions, Abbreviation List, and IC Data
Sheets62
Abbreviation List65
IC Data Sheets68
10 Recommended / Spare Parts List72
11 Revision List79
Copyright 2008 Philips Consumer Lifestyle B.V. Eindhoven, The Netherlands.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronic,
mechanical, photocopying, or otherwise without the prior permission of Philips.
Published by CS 0861 BU CD Customer CarePrinted in the NetherlandsSubject to modificationEN 3122 785 17730
Figures below can deviate slightly from the actual situation,
due to the different set executions.
Specifications are indicative (subject to change)
1.1Technical Specifications
1.1.1 Technical Specifications
Type: LCD
Outline dimensions: 760.0 mm(H) x 450.0 mm(V) x 47.4(D)
Pitch (mm): 510.75 .um(H) x 170.25um(V)
Pixel format: 1366 horiz. by 768 vert. pixels
Color pixel arrangement : RGB vertical stripe
Display surface: Hard coating(3H),Anti-glare treatment
Number of color: 16,777,216 colors ( 8 bits)
Backlight: 16 CCFL
Active area (WxH): 697.68mm X 392.26 mm
View angle: Viewing angle free(R/L 176(Typ.),U/D
1Red video input9DDC +5V
2Green video input /SOG10Logic ground
3Blue video input11GND
4GND12Serial data line (SDA)
5GND- cable detect13H. Sync / H+V
6Red video ground14V. Sync
7Green video ground15Data clock line (SCL)
8Blue video ground
TV video input /output connectors
A. HDMI for digital Video / Audio interface with pin assignment
id driht eht fI .tekram eht no tes VT eht fo noisrev
2 a si
tnereffid owt era ereht neht ,)1000005330B
eht gniredro rof
Z...A sretcarahc eht dna 9...1 srebmun eht ,t
nac s.M.O.B tnereffid 53 = 62 sulp 9 :latot ni os ,desu eb nac
.rebmun
ri
apeR leveL tnenopmoC ro )
ediced ot erudecorp riaper ruoy
no deriaper eb dluohs ti fi ro degnahcxe eb ot sah draob eht fi
ti ,esiwrehtO .draob evitcefed eht no redlos ton od ,yletelpmoc
!gnigrahc kcab rof reilppus .M.E.O eht o
cir
elbissop a evah ot detcepxe era secruos emos elihW
.drager
ssel
cepxenu e
a
otni gnihcaer erofeB .dediova tseb era taht snoitcaer
.noituacerp ecivres doog a si dna ,od ot ysae si tI
.noitalusni egatlov hgih eht tset ot tseb si ti ,
6
TPS1.1L LA
3. Directions for User
3. Directions for User
You can download this information from the following websites:
http://www.philips.com/support
http://www.p4c.philips.com
OSD Menu list
1st Layer2nd Layer3rd Layer4th Layer
PC Mode
Picture
Sound
Color temp
Normal
Warm
Cool
Brightness
Contrast
Auto adjustYes
Manual adjust
Phase
Clock
Horizontal
Vertical
Smart sound
Personal
Speech
Music
Movie
Multimedia
Settings
Treble
Install
AVL
Factory reset
Bass
Balance
OnVirtual surround
Off
On
Off
Full screenFeaturesPicture format
4:3
EnglishLanguage
Latem
No
Yes
3. Directions for User
TV / AV/ S-VIDEO / HD MODE
1st Layer2nd Layer3rd Layer4th Layer5th Layer
Picture
Sound
Features
Smart picture
Contrast
Brightness
Color
Sharpness
Tint
Color temp
Picture format
Smart sound
Settings
AVL
Timer
NR
Auto lock
Source list
Personal
Rich
Nature
Soft
Multimedia
Normal
Warm
Cool
Super zoom
4:3
Movie expand 14:9
Movie expand 16:9
16:9 subtitle
Widescreen
Personal
Speech
Music
Movie
Multimedia
Treble
Bass
Balance
OnVirtual surround
Off
On
Off
Clock
Start time
Stop time
Sleep timer
On
Off
Lock program
Change codeEnter New CodeConfirm Code
Clear allStart ?
TV
CVI
AV1
AV2 (side)
PC
DVI
TPS 1.1L LA
7
8
TPS1.1L LA
3. Directions for User
Install
EnglishLanguage
Latam
Auto storeStart ?
Manual store
Prog. no
Finetune
Store
Channel setting
Factory reset
Channel edit
Channel swap
Channel sortSort ?
No
Yes
Auto store
Please wait
Prog. found
Frequency
MHzManual store
Start ?
Store ?
Stored
Channel
Skipped
From
To
Exchange
ChannelName edit
Name
Active
Skipped
Exchange ?
Exchanged
Sorting
Sort complete
4. Mechanical Instructions
4. Mechanical Instructions
Index of this chapter:
4.1 Assy/Panel Removal
4.2 Set Re-assembly
4.1 Assy/Panel Removal
Notes: Please put your machine on soft material to avoid to scrape
panel when you disassemble it.
Front view
TPS1.1L LA
Step 4. Remove shielding.
Remove 10 screws as Fig.5 and remove 10 screws as Fig6.
9
Fig.4
Back view
Step 1. Remove the stand.
Remove the four screws as Fig.2.
Step 2. Remove the Back cover assy.
Remove the 10 screws on the bottom side as Fig.3.
Fig.1
Fig.2
Fig.5
Fig.6
Step 5. Remove Scaler board, Power board, SideAV board and
IR board.
Remove 17 screws as Fig.7.
Step 3. Remove the Vase plate and Bracket-base.
Remove the 14 screws on the bottom side as Fig.4.
Fig.3
Fig.7
10
Step 6. Remove frame-PCB.
Step 7. Remove Metal frame.
TPS1.1L LA
Remove 7 screws as Fig.8.
Remove 16 screws as Fig.9.
4. Mechanical Instructions
Fig.8
4.2 Set Re-assembly
To re-assemble the whole set, execute all processes in reverse
order.
Notes:
a. While re-assembling, make sure that all cables are placed
and connected in their original position.
b. Pay special attention not to damage the EMC foams at the
Fig.9
Fig.9
SSB shielding. Check that EMC foams are put correctly on
their places.
Fig.12
Service Position
Step 8. Remove Metal frame.
Remove 4 screws as Fig.10.
In warranty, it is not allowed to disassembly the LCD panel, even the
backlight unit defect.
Out of warranty, the replacment of backlight unit is a correct way
when the defect is cused by backlight (CCFL,Lamp).
Fig.10
Fig.11
5. Service Modes, Error Codes and Fault Finding
TPS1.1L LA
5. Service Modes, Error Codes and Fault Finding
index of this chapter:
5.1 CSM
5.2 Factory Mode
5.
3 Repair Flow Chart
5.1 CSM
It can display CSM windows message when press Menu+123654 on the button (RC) remote control in normal operation mode.
Then choose The following information is displayed on screen:
CSM ItemContentsRemark
1: Set Type32TA2800/55Project name
2: Production code0123456789012314 digit production- code(serial number)
3: SW-naming mainprocessorMST96889LD-LFSW-naming of Mstar/Trident
4: Code 10 0 0 0 0Error codes in NVM/EEPROM (5 last logged errors)
5: Code 20 0 0 0 0Error codes in NVM/EEPROM (5 first logged errors)
6: Key (HDCP)EnabledHDMI information whether HDCP-key is valid
7: NVM-naming24C32- Without-BDSContents per display-type
The real picture as below:
11
55
About error code,Please refer to the table below.
Error codeEvent
0x01DDR error
0x02IIC bus error
0x03Tuner error
0x04Demod error
12
TPS1.1L LA
5. Service Modes, Error Codes and Fault Finding
5.2 Factory Mode
It can enter Factory Mode
1. Press" Menu in normal operation mode to enter OSD.
2. Press "062596+Menu on the button (RC) remote control in OSD.
3. The screen will appear "FAC" in the bottom, choose it and press the right key.
OSD behavior:
Before press number key change OSD item
Now remove previous function, press number key then press OK will change value
ItemDescriptionRange method of operation
//Actio n It ems
0ExitFactorypress OK.
1AutoColor
//Switch Items
2PowerOnOn/Off
3AGING MODEturn<On> and no signal inputOn/Off
//ADC G ain & Offset
4ADC_GA IN_R0~255 Press Left and Right to change value
5ADC_GA IN_G0~255
6ADC_GA IN_B0~255
7ADC_OFFSET_R0~127
8ADC_OFFSET_G0~127
9ADC_OFFSET_B0~127
"
"
"
"
PC: any pattern has black and white
YPbPr:SMPTEbar(color bar ), any timing.
(values different by VGA and YPbPr)
Au toColor changes thos e items
press OK. when autoc olor, the OSD disappear , when
finished. OSD appear.
//Color Temperature(values different by AV,VGA,DTV,YPbPr)
10CLR_TEMP_RBack-End Scaler R G B Gain0~255 Press Left and Right to change value
11CLR_TEMP_G0~255
12CLR_TEMP_B0~255
//Tuner & Panel Id
13EEPROM IDvalue different by type
The below pictures is for your reference:
Step1: press MENU+062596 in user mode.
The factory content:
Step2: choose F3 98 V1.77.74.3,press the right key, then
enter the factory mode.
5.3 Repair Flow Chart
5. Service Modes, Error Codes and Fault Finding
1.No work/LED is off
TPS1.1L LA
13
Check if
power switch is
normal
Yes
Check
IR board CN0201
pin3=5V,pin5=5V
Yes
Check scaler board
U7105 pin1=24V,pin4=5V
2.No raster/picture too
dim
No
No
Replace Power switch
Check IR board
Check
power board
CN913,pin1=24V,
pin3=12V
Yes
Check
power board
IC920 pin2,IC970
pin2=12V
Yes
Check scaler board
No
No
Check Scaler board
Check IC920,IC970
14
TPS1.1L LA
5. Service Modes, Error Codes and Fault Finding
3.No picture/LED is green
Check
scaler board U7105
pin1=24V,pin4=5V
Yes
No
Check power
Check if
working voltage
U7104 pin1=5V,
pin4=3.3V
Yes
Check if clock
source X4101
Yes
Check if
RGB,clk,H/V and
DE signal output 128
bits TTL
Yes
Check
resistors-network
No
No
No
No
Check circuit around
each regulator and
eliminate short and
open situation
Replace X4101
Try to replace
flash Rom
EEPROM
Replace bad resistorsnetwork
Yes
Replace LVDS cable
4.No TV sound
Check if
tuner TU2101 pin11
output IF signal
Yes
Check U4101
No
Replace TU2101
5. Service Modes, Error Codes and Fault Finding
5.No earthphone sound
TPS1.1L LA
15
Check
U6301 pin33=3.3V
Yes
Check U6303
pin6= 5V
pin5,7=HPL/HPR
Yes
Replace Side AV Board
6.No remote function
No
No
Eliminate short and open
situation
Replace U6303
Tty another
remote control
Yes
Check IR receiver
7.LED and function
key poor
Check circuit around
control board and cable
between control board
and scaler board