Philips tda8792 DATASHEETS
INTEGRATED CIRCUITS
DATA SH EET
TDA8792
3.3 V, 25 MHz 8-bit
analog-to-digital converter (ADC)
Product specification
Supersedes data of 1995 Apr 26
File under Integrated Circuits, IC02
1996 Feb 21
Philips Semiconductors Product specification
3.3 V, 25 MHz 8-bit
analog-to-digital converter (ADC)
FEATURES
• 8-bit resolution
• Sampling rate up to 25 MHz
• 30 MHz input signal bandwidth (full scale)
• High signal-to-noise ratio over a large analog input
frequency range (7.3 effective bits at 4.43 MHz
full-scale input at f
• CMOS compatible digital inputs
• External reference voltage regulator
• Power dissipation only 53 mW (typical)
• Standby mode (only 1.2 mW typical)
• Low analog input capacitance, no buffer amplifier
required
• No sample-and-hold circuit required.
QUICK REFERENCE DATA
= 25 MHz)
clk
TDA8792
APPLICATIONS
Analog-to-digital conversion for:
• General purpose
• Hand-held equipment
• Mobile telecommunication
• Instrumentation
• Video.
GENERAL DESCRIPTION
The TDA8792 is a 8-bit analog-to-digital converter (ADC)
for low-voltage, portable applications. It operates at 3.3 V
and converts the analog input signal into 8-bit
binary-coded digital words at a maximum sampling rate of
25 MHz. The output data is valid after a delay of 6 clock
cycles.
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
V
DDA
V
DDD
V
DDO
I
DDA
I
DDD
I
DDO
analog supply voltage 2.85 3.3 3.6 V
digital supply voltage 2.70 3.3 3.6 V
output stages supply voltage 2.5 3.3 3.6 V
analog supply current − 12 20 mA
digital supply current − 36mA
output stages supply current f
= 25 MHz; CL= 15 pF;
clk
− 12mA
ramp input
INL integral non-linearity f
DNL differential non-linearity f
f
clk(max)
P
tot
maximum clock frequency 25 −−MHz
total power dissipation f
= 25 MHz; ramp input −±0.4 ±0.8 LSB
clk
= 25 MHz; ramp input −±0.3 ±0.75 LSB
clk
= 25 MHz; CL= 15 pF;
clk
− 53 100 mW
ramp input
ORDERING INFORMATION
TYPE
NUMBER
NAME DESCRIPTION VERSION
PACKAGE
TDA8792M SSOP24 plastic shrink small outline package; 24 leads; body width 5.3 mm SOT340-1
1996 Feb 21 2
Philips Semiconductors Product specification
3.3 V, 25 MHz 8-bit
analog-to-digital converter (ADC)
BLOCK DIAGRAM
dbook, full pagewidth
STDBY
1
V
DDD
2
V
SSD2
3
V
SSA1
4
V
I
V
DDA
I
bias
V
RT
5
6
7
8
7 x 8
OFFSET
COMPENSATED
COMPARATORS
DECODER
LATCHES
TDA8792
8
OUTPUT
BUFFER
24
23
22
21 D7
D620
D519
D4 18
D317
TDA8792
CLK
V
SSO
V
DDO
MSB
data outputs
V
V
RM
V
RB
SSA2
MLD119 - 1
D2 16
D1 15
D014
LSB
OE 13
9
10
12
REFERENCE
LADDER
DAC
Fig.1 Block diagram.
1996 Feb 21 3
Philips Semiconductors Product specification
3.3 V, 25 MHz 8-bit
analog-to-digital converter (ADC)
PINNING
SYMBOL PIN DESCRIPTION
STDBY 1 standby input
V
DDD
V
SSD2
V
SSA1
V
I
V
DDA
I
bias
V
RT
V
RM
V
RB
n.c. 11 not connected
V
SSA2
OE
D0 14 data output; bit 0 (LSB)
D1 15 data output; bit 1
D2 16 data output; bit 2
D3 17 data output; bit 3
D4 18 data output; bit 4
D5 19 data output; bit 5
D6 20 data output; bit 6
D7 21 data output; bit 7 (MSB)
V
DDO
V
SSO
CLK 24 clock input
2 digital supply voltage (+3.3 V)
3 digital ground 2
4 analog ground 1
5 analog input voltage
6 analog supply voltage (+3.3 V)
7 bias current input
8 reference voltage TOP input
9 reference voltage MIDDLE
10 reference voltage BOTTOM input
12 analog ground 2
output enable input (CMOS level
13
input, active LOW)
positive supply voltage for output
22
stage (+3.3 V)
23 output ground
handbook, halfpage
V
DDD
V
SSD2
SSA1
V
DDA
I
bias
V
V
RM
V
SSA2
RT
RB
n.c.
1
2
3
4
V
5
I
6
TDA8792
7
8
9
10
11
12
MLD120 - 1
STDBY
V
V
Fig.2 Pin configuration.
TDA8792
CLK
24
V
23
SSO
22
V
DDO
21
D7
20
D6
D5
19
D4
18
17
D3
D2
16
D1
15
D0
14
OE
13
1996 Feb 21 4
Philips Semiconductors Product specification
3.3 V, 25 MHz 8-bit
TDA8792
analog-to-digital converter (ADC)
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
V
DDA
V
DDD
V
DDO
∆V
∆V
∆V
V
I
V
clk(p-p)
I
O
T
stg
T
amb
T
j
DD1
DD2
DD3
analog supply voltage note 1 −0.5 +5.0 V
digital supply voltage note 1 −0.5 +5.0 V
output stages supply voltage note 1 −0.5 +5.0 V
supply voltage differences between
∆V
DD1=VDDA
− V
DDD
supply voltage differences between
∆V
DD2=VDDD
− V
DDO
supply voltage differences between
∆V
DD3=VDDA
− V
DDO
input voltage referenced to V
AC input voltage for switching
referenced to V
SSA
SSD
−0.3 +0.3 V
−1.0 +1.0 V
−1.0 +1.0 V
−0.5 +5.0 V
− V
DDD
(peak-to-peak value)
output current − 10 mA
storage temperature −55 +150 °C
operating ambient temperature −20 +75 °C
junction temperature − +125 °C
V
Note
1. The supply voltages V
differences ∆V
DD1
, ∆V
DDA
DD2
, V
DDD
and ∆V
and V
DDO
are respected.
DD3
may have any value between −0.5 V and +5.0 V provided that the
HANDLING
Inputs and outputs are protected against electrostatic discharges in normal handling. However, to be totally safe, it is
desirable to take normal precautions appropriate to handling integrated circuits.
THERMAL CHARACTERISTICS
SYMBOL PARAMETER VALUE UNIT
R
th j-a
thermal resistance from junction to ambient in free air 119 K/W
1996 Feb 21 5
Loading...