Philips tda1307 DATASHEETS

INTEGRATED CIRCUITS

DATA SH EET

TDA1307

High-performance bitstream digital filter

Preliminary speciﬁcation Supersedes data of July 1993 File under Integrated Circuits, IC01

1996 Jan 08

Philips Semiconductors Preliminary speciﬁcation

High-performance bitstream digital ﬁlter TDA1307

FEATURES

• Multiple format inputs: I2S, Sony 16, 18 and 20-bit

• 8-sample interpolation error concealment

• Digital mute, attenuation −12 dB

• Digital audio output function (biphase-mark encoded)

according to IEC 958

• Digital silence detection (output)

• Digital de-emphasis (selectable, FS-programmable)

• 8 × oversampling finite impulse response (FIR) filter

• DC-cancelling filter (selectable)

• Peak detection (continuous) and read-out to

microprocessor

• Fade function: sophisticated volume control

• Selectable 3rd/4th order noise shaping

• Selectable dither generation and automatic scaling

• Dedicated TDA1547 1-bit output

• Differential mode bitstream: complementary data

outputs available

• Simple 3-line serial microprocessor command interface

• Flexible system clock oscillator circuitry

• Power-on reset

• Standby function

• SDIP42 package.

QUICK REFERENCE DATA

Voltages are referenced to V

(ground = 0 V); all VSS and all VDD connections should be connected externally to the

same supply.

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

DDC1,2,3

supply voltage

4.5 5.0 5.5 V

(pins 21, 41 and 8)

DDOSC

DDAR

DDAL

DDC1,2,3

supply voltage (pin 24) 4.5 5.0 5.5 V supply voltage (pin 32) 4.5 5.0 5.5 V supply voltage (pin 29) 4.5 5.0 5.5 V supply current

VDD=5V − 75 − mA

(pins 21, 41 and 8)

DDOSC

DDAR

DDAL

XTAL

amb

tot

supply current (pin 24) VDD=5V − 2 − mA supply current (pin 32) VDD=5V − 2 − mA supply current (pin 29) VDD=5V − 1 − mA oscillator clock frequency − 33.8688 − MHz operating ambient temperature −20 − +70 °C total power consumption − 400 − mW

ORDERING INFORMATION

PACKAGE

TYPE NUMBER

NAME DESCRIPTION VERSION

TDA1307 SDIP42 plastic shrink dual in-line package; 42 leads (600 mil) SOT270-1

1996 Jan 08 2

Philips Semiconductors Preliminary speciﬁcation

High-performance bitstream digital ﬁlter TDA1307

GENERAL DESCRIPTION

The TDA1307 is an advanced oversampling digital filter employing bitstream conversion technology, which has been designed for use in premium performance digital audio applications. Audio data is input to the TDA1307 through its multiple-format interface. Any of the four formats (I2S, Sony 16, 18 or 20-bit) are acceptable. By using a highly accurate audio data processing structure, including 8 times oversampling digital filtering and up to 4th order noise shaping, a high quality bitstream is produced which, when used in the recommended combination with the TDA1547 bitstream DAC, provides the optimum in dynamic range and signal-to-noise performance. With the TDA1307, a high degree of versatility is achieved by a multitude of functional features and their easy accessibility; error concealment functions,

handbook, full pagewidth

20-bit f

= 768f

system

TDA1307 TDA1547

1-bit, 192f

audio peak data information and an advanced patented digital fade function are accessible through a simple microprocessor command interface, which also provides access to various integrated system settings and functions.

TDA1307 plus TDA1547 high-performance bitstream digital filter plus DAC combination:

For many features:

• Highly accessible structure

• Intelligent audio data processing.

For optimum performance:

• 4th order noise shaping

• Improvement dynamic range (113 dB)

• Improvement signal-to-noise (115 dB).

8 × oversampling FIR

filter, 20-bit

24 × upsampling

3rd or 4th order noise shaping,

1-bit end quantization

1-bit high-performance

digital-to-analog

converter

Fig.1 High performance bitstream reconstruction system.

3rd order analog postfilter, fo = 55 kHz Butterworth response

MGB983

1996 Jan 08 3

Philips Semiconductors Preliminary speciﬁcation

High-performance bitstream digital ﬁlter TDA1307

BLOCK DIAGRAM

handbook, full pagewidth

DSR

DSL

TEST1 TEST2

RAB

POR

DDC3

DDC1

DDOSC

DDAL

DDAR

DDC2

1fs AUDIO DATA INPUTS

WS SCK

1234

MULTIPLE FORMAT

INPUT INTERFACE

ERROR CONCEALMENT,

INTERPOLATION, MUTING

12 11

36 37

MICRO–

PROCESSOR

INTERFACE

DIGITAL SILENCE DETECTION

DE–EMPHASIS FILTER

FIR HALFBAND FILTER

STAGE 1: 1fs to 2f

DC–CANCELLING FILTER

PEAK DETECTION

FADE FUNCTION

VOLUME CONTROL

FIR HALFBAND FILTER

STAGE 2: 2fs to 4f

FIR HALFBAND FILTER

STAGE 3: 4fs to 8f

DITHER AND SCALING

SD EFAB

DIGITAL OUTPUT

TDA1307

OSCILLATOR

CLOCK

GENERATION

DISTRIBUTION

CRYSTAL



AND

RESYNC

DOBM

DSTB

SBCL

SBDA

SSOSC

XTAL1

XTAL2

CMIC

CDEC

CLC1

CLC2

CDCC

SSC2

SSC3

SSAL

SSAR

SSC1

1996 Jan 08 4

3rd/4th ORDER

NOISE SHAPER

27 28 35 34 33 26

DOL NDOL CDAC NDOR

BITSTREAM DATA OUTPUTS

DOR MODE

Fig.2 Block diagram.

MGB989 

Philips Semiconductors Preliminary speciﬁcation

High-performance bitstream digital ﬁlter TDA1307

PINNING

SYMBOL PIN TYPE, I/O DESCRIPTION

WS 1 I word select input to data interface SCK 2 I clock input to data interface SD 3 I data input to interface EFAB 4 I

(1)

SBCL 5 I subcode clock: a 10-bit burst clock (typ. 2.8224 MHz) input which synchronizes

SBDA 6 I subcode data: a 10-bit burst of data, including ﬂags and sync bits, serially input

CDEC 7 O decoder clock output: frequency division programmable by means of

V V

DDC3 SSC2

8 positive supply 3 9 ground 2

DOBM 10 O digital audio output: this output contains digital audio samples which have

DSL 11 O digital silence detected (active LOW) on left channel DSR 12 O digital silence detected (active LOW) on right channel DSTB 13 I

(2)

CLC1 14 I application mode programming pin for CDEC (pin 7) frequency division CMIC 15 O clock output, provided to be used as running clock by microprocessor

SSC3

16 ground 3 CLC2 17 I application mode programming pin for CDEC (pin 7) frequency division CDCC 18 I master / slave mode selection pin RESYNC 19 O resynchronization: out-of-lock indication from data input section (active HIGH) POR 20 I V

DDC1

21 supply voltage 1

(2)

XTAL1 22 I crystal oscillator terminal: local crystal oscillator sense forced input in slave mode XTAL2 23 O crystal oscillator output: drive output to crystal V

DDOSC

SSOSC

MODE 26 I

24 positive supply connection to crystal oscillator circuitry

25 ground connection to crystal oscillator circuitry

(2)

DOL 27 O data output left channel to bitstream DAC TDA1547 NDOL 28 O complementary data output left channel to TDA1547 in double differential mode V

DDAL

SSAL

SSAR

DDAR

29 positive supply connection to output data driving circuitry, left channel

30 ground connection to output data driving circuitry, left channel

31 ground connection to output data driving circuitry, right channel

32 positive supply connection to output data driving circuitry, right channel DOR 33 O data output right channel to TDA1547

error ﬂag (active HIGH): input from decoder chip indicating unreliable data

the subcode data

once per frame, clocked by burst clock input SBCL

pins 14 (CLC1) and 17 (CLC2) to output 192, 256, 384 or 768 times f

received interpolation, attenuation and muting plus subcode data; transmission is in biphase-mark code

DOBM standby mode enforce pin (active HIGH)

(in master mode only), output 96f

power-on reset (active LOW)

evaluation mode programming pin (active LOW); in normal operation, this pin should be left open-circuit or connected to the positive supply

1996 Jan 08 5

Philips Semiconductors Preliminary speciﬁcation

High-performance bitstream digital ﬁlter TDA1307

SYMBOL PIN TYPE, I/O DESCRIPTION

NDOR 34 O complementary data output right channel to TDA1547 in double differential mode CDAC 35 O clock output to bitstream DAC TDA1547 TEST1 36 I TEST2 37 I DA 38 I/O

CL 39 I V

SSC1

DDC2

RAB 42 I

(1) (1)

(2)

40 ground 1

41 supply voltage 2

(2)

Notes

1. These pins are configured as internal pull-down.

2. These pins are configured as internal pull-up.

test mode input; in normal operation this pin should be connected to ground test mode input; in normal operation this pin should be connected to ground bidirectional data line intended for control data from the microprocessor and peak

data from the TDA1307 clock input, to be generated by the microprocessor

command / peak data request line

handbook, halfpage

SCK

SD EFAB SBCL SBDA

CDEC

DDC3

SSC2

DOBM

DSL

DSR

DSTB

CLC1 CMIC

SSC3

CLC2

CDCC

RESYNC

POR

DDC1

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20

TDA1307

MGB980

RAB

DDC2

SSC1

TEST2

TEST1

CDAC

NDOR

DOR

DDAR

SSAR

SSAL

DDAL

NDOL

DOL

MODE

SSOSC

DDOSC

XTAL2

2221

XTAL1

1996 Jan 08 6

Fig.3 Pin configuration.

Philips Semiconductors Preliminary speciﬁcation

High-performance bitstream digital ﬁlter TDA1307

FUNCTIONAL DESCRIPTION

In the block diagram, Fig.1, a general subdivision into three main functional sections is illustrated. The actual signal processing takes place in the central sequence of blocks, a representation of the audio data path from top to bottom. The two blocks named “Microprocessor Interface” and “Clock Generation and Distribution” fulfil a general auxiliary function to the audio data processing path. The Microprocessor Interface provides access to all the blocks in the audio path that require or allow for configuration or selection, and manipulates data read-out from the Peak Detection block, all via a simple three-line interface. The Clock Generation and Distribution section, driven either by its integrated oscillator circuit with external crystal or by an externally provided master clock, provides the data processing blocks with timebases, manages the system mode dependent frequency settings, and conveniently generates clocks for external use by the system decoder IC and microprocessor. Following are detailed explanations of the functions of each block in the audio data processing path and their setting options manipulated by the microprocessor interface, the use of the microprocessor interface, and the functions of the clock section with its various system settings.

Clock generation and distribution

The clock generation section of the TDA1307 is designed to accommodate two main modes. The master mode, in which the TDA1307 is the master in the digital audio system, and for which the clock is generated by connecting

a crystal of 768f

(33.8688 MHz) to the crystal oscillator

pins XTAL1 (pin 22) and XTAL2 (pin 23); and the slave mode, in which the TDA1307 is supplied a clock by the IC in the system that acts as the master (e.g. the digital audio interface receiver). In this event a clock signal frequency of 256fs is input to pin XTAL1. Master or slave mode is programmed by means of pin CDCC (pin 18) logic 1 for master and logic 0 for slave mode. The circuit diagram of Fig.4 shows the typical connection of the external oscillator circuitry and crystal resonator for master mode operation. Note that the positive supply V

DDOSC

is the reference to the oscillator circuitry. The LC network is used for suppression of the fundamental frequency component of the overtone crystal. Figure 5 shows how to connect for slave mode operation. A clock frequency of typical 256f

and levels of 0 V/+5 V is input to XTAL1 via AC coupling. The 100 kΩ resistor and the 10 nF capacitor are required to provide the necessary biasing for XTAL2 by filtering and feeding back the output signal of XTAL1.

Besides generating all necessary internal clocks for the audio data processing blocks and the clock to the DAC, the clock generation block further provides two clocks for external use when operating in master mode. Pin CDEC (pin 7) is used as the running clock for the system decoder IC, and pin CMIC (pin 15) is used as the running clock for the system microprocessor. CMIC outputs, by a fixed divider ratio to XTAL2, a clock signal at 96fs. For CDEC the divider ratio is programmable by means of pins CLC1 (pin 14) and CLC2 (pin 17). Table 1 gives the clock divider programming relationships.

Table 1 Clock divider programming

CLC1 CLC2 CDEC OUTPUT FREQUENCY

0 0 256f 0 1 384f 1 0 768f 1 1 192f

1996 Jan 08 7

s s s s

Philips Semiconductors Preliminary speciﬁcation

High-performance bitstream digital ﬁlter TDA1307

handbook, halfpage

XTAL2

3.3 µH

1 nF

10 kΩ

10 pF

100

+5 V

kΩ

10 pF

33.8688

MHz

XTAL1

DDOSC

SSOSC

TDA1307

MGB981 

Fig.4 External crystal oscillator circuit.

handbook, halfpage

fi = 256f

+5 V

20 pF

30 pF

100 kΩ

10 nF

XTAL2

XTAL1

DDOSC

SSOSC

TDA1307

MGB982 

1996 Jan 08 8

Fig.5 External clock input connections.

Philips Semiconductors Preliminary speciﬁcation

High-performance bitstream digital ﬁlter TDA1307

Microprocessor interface

The microprocessor interface provides access to virtually all of the functional blocks in the audio data processing section. Its destination is two-fold: system constants (such as input format and sample frequency) as well as system variables (attenuation, muting, de-emphasis, volume control data etc.) can be ‘written to’ the respective blocks (command mode), and continuously collected stereo peak data ‘read from’ the peak detection block (peak request). The system settings are stored in the TDA1307 in an internal register file. Peak data is read from the stereo peak value register.

handbook, full pagewidth

RAB 42

DA/ACK 38

THREE-LINE MICROPROCESSOR INTERFACE BUS Communication is realized by a three-line bus, consisting

of the following signals (see Fig.6):

• Clock input CL (pin 39), to be generated by the

microprocessor

• Command/request input RAB (pin 42), by which either

of the two mode commands (RAB = 0) and peak request (RAB = 1) are invoked

• Bidirectional data line DA (pin 38), which either receives

command data from the microprocessor or outputs peak data from the peak detection block.

CL and RAB both default HIGH by internal pull-up, DATA is 3-state (high impedance, pull-up, pull-down).

REQUEST/COMMAND

COMMAND DATA PEAK DATA

CL 39

MICROPROCESSOR

Fig.6 Three-line microprocessor interface bus.

1996 Jan 08 9

TDA1307

CLOCK

MGB984 

Philips Semiconductors Preliminary speciﬁcation

High-performance bitstream digital ﬁlter TDA1307

INITIALIZATION OF THE BUS RECEIVER The microprocessor interface section is initialized

automatically by the power-on reset function, POR (pin 20). A LOW input on POR will initiate the reset procedure, which encompasses a functional reset plus setting of the initial states of the control words in the command register file. A wait time of at least one audio sample time after a LOW-to-HIGH transition of POR must be observed before communication can successfully be established between the TDA1307 and the microprocessor. In addition to the POR function, a software reset function issued from the microprocessor is provided (see section “Organization and programming of the internal register file”), which has the sole function of reinstating the initial values of the microprocessor control register. More information on initializing the TDA1307 can be found under “Application Information”.

OMMAND PROTOCOL

C The protocol for writing data to the TDA1307 is illustrated

in Fig.7. The command mode is invoked by forcing RAB LOW. A unit command is given in the form of an 8-bit burst on the DA line, clocked on the rising edge of CL. The command consists of 4 address bits followed by 4 control data bits (both MSB first). A next command may be immediately issued while keeping RAB forced LOW. Only commands for which the MSB of the address bits is

LOW are accepted; of the remaining set of addresses, only four have meaning (see section “Organization and programming of the internal register file”). The command input receiver is provided with a built-in protection against erroneous command transfer due to spikes, by a 2-bit debounce mechanism on lines DA and CL. The waveforms on these lines are sampled by the receiver at the internal system clock rate 256f

. A state transition on

DA or CL is accepted only when the new state perseveres for two consecutive sampled waveform instants.

RGANIZATION AND PROGRAMMING OF THE INTERNAL

Command data received from the microprocessor is stored in an internal register file (see Table 2), which is organized as a page of 10 registers, each containing a 4-bit command data word (D3 to D0). Access to the words in the register file involves two controls: selection of the address of a set of registers (by means of A3, A2, A1 and A0) and setting the number of the bank in which the desired register is located (by means of the ‘bank bits’ B0 and B1). First the desired bank is selected by programming the command word at address 0000 (supplying the bank bits plus refreshing bits ATT and DIM). A subsequent addressing (one of three addresses, 1H, 4H and 6H) will yield access to the register corresponding to the last set bank.

handbook, full pagewidth

RAB

DA (TDA1307)

DA (µP)

DRW

CKL

DSM

A3 A2 A1 A0 D3 D2 D1 D0

CKH

Fig.7 Microprocessor command protocol.

1996 Jan 08 10

DHM

MGB995 

+ 23 hidden pages