Philips TDA1072A-V4 Datasheet

DATA SH EET

Product speciﬁcation File under Integrated Circuits, IC01

May 1984

INTEGRATED CIRCUITS

TDA1072A

AM receiver circuit

May 1984 2

Philips Semiconductors Product speciﬁcation

AM receiver circuit TDA1072A

GENERAL DESCRIPTION

The TDA1072A integrated AM receiver circuit performs the active and part of the filtering functions of an AM radio receiver. It is intended for use in mains-fed home receivers and car radios. The circuit can be used for oscillator frequencies up to 50 MHz and can handle r.f. signals up to 500 mV. R.F. radiation and sensitivity to interference are minimized by an almost symmetrical design. The voltage-controlled oscillator provides signals with extremely low distortion and high spectral purity over the whole frequency range even when tuning with variable capacitance diodes. If required, band switching diodes can easily be applied. Selectivity is obtained using a block filter before the i.f. amplifier.

Features

• Inputs protected against damage by static discharge

• Gain-controlled r.f. stage

• Double balanced mixer

• Separately buffered, voltage-controlled and temperature-compensated oscillator, designed for simple coils

• Gain-controlled i.f. stage with wide a.g.c. range

• Full-wave, balanced envelope detector

• Internal generation of a.g.c. voltage with possibility of second-order filtering

• Buffered field strength indicator driver with short-circuit protection

• A.F. preamplifier with possibilities for simple a.f. filtering

• Electronic standby switch.

QUICK REFERENCE DATA

PACKAGE OUTLINE

16-lead DIL; plastic (SOT38); SOT38-1; 1996 August 09.

Supply voltage range V

7,5 to 18 V

Supply current range I

15 to 30 mA

R.F. input voltage for S + N/N = 6 dB at m = 30% V

typ. 1,5 µV

R.F. input voltage for 3% total harmonic

distortion (THD) at m = 80% V

typ. 500 mV

A.F. output voltage with V

= 2 mV;

= 1 MHz; m = 30% and fm= 400 Hz V

o(af)

typ. 310 mV

A.G.C. range: change of V

for 1 dB change of V

o(af)

typ. 86 dB

Field strength indicator voltage at

= 500 mV; R

L(9)

= 2,7 kΩ V

IND

typ. 2,8 V

May 1984 3

Philips Semiconductors Product speciﬁcation

AM receiver circuit TDA1072A

Fig.1 Block diagram and test circuit (connections shown in broken lines are not part of the test circuit).

(1) Coil data: TOKO sample no. 7XNS-A7523DY; L1 : N1/N2 = 12/32; Qo = 65; QB = 57.

Filter data: Z

= 700 Ω at R

3-4

= 3 kΩ; ZI = 4,8 kΩ.

May 1984 4

Philips Semiconductors Product speciﬁcation

AM receiver circuit TDA1072A

FUNCTIONAL DESCRIPTION Gain-controlled r.f. stage and mixer

The differential amplifier in the r.f. stage employs an a.g.c. negative feedback network to provide a wide dynamic range. Very good cross-modulation behaviour is achieved by a.g.c. delays at the various signal stages. Large signals are handled with low distortion and the S/N ratio of small signals is improved. Low noise working is achieved in the differential amplifier by using transistors with low base resistance.

A double balanced mixer provides the i.f. output signal to pin 1.

Oscillator

The differential amplifier oscillator is temperature compensated and is suitable for simple coil connection. The oscillator is voltage-controlled and has little distortion or spurious radiation. It is specially suitable for electronic tuning using variable capacitance diodes. Band switching diodes can easily be applied using the stabilized voltage V

11-16

. An extra

buffered oscillator output (pin 10) is available for driving a synthesizer. If this is not needed, resistor R

L(10)

can be omitted.

Gain-controlled i.f. ampliﬁer

This amplifier comprises two cascaded, variable-gain differential amplifier stages coupled by a band-pass filter. Both stages are gain-controlled by the a.g.c. negative feedback network.

Detector

The full-wave, balanced envelope detector has very low distortion over a wide dynamic range. Residual i.f. carrier is blocked from the signal path by an internal low-pass filter.

A.F. preampliﬁer

This stage preamplifies the audio frequency output signal. The amplifier output has an emitter follower with a series resistor which, together with an external capacitor, yields the required low-pass for a.f. filtering.

A.G.C. ampliﬁer

The a.g.c. amplifier provides a control voltage which is proportional to the carrier amplitude. Second-order filtering of the a.g.c. voltage achieves signals with very little distortion, even at low audio frequencies. This method of filtering also gives fast a.g.c. settling time which is advantageous for electronic search tuning. The a.g.c. settling time can be further reduced by using capacitors of smaller value in the external filter (C16 and C17). The a.g.c. voltage is fed to the r.f. and i.f. stages via suitable a.g.c. delays. The capacitor at pin 7 can be omitted for low-cost applications.

Field strength indicator output

A buffered voltage source provides a high-level field strength output signal which has good linearity for logarithmic input signals over the whole dynamic range. If the field strength information is not needed, R

L(9)

can be omitted.

Standby switch

This switch is primarily intended for AM/FM band switching. During standby mode the oscillator, mixer and a.f. preamplifier are switched off.

Short-circuit protection

All pins have short-circuit protection to ground.

May 1984 5

Philips Semiconductors Product speciﬁcation

AM receiver circuit TDA1072A

RATINGS

Limiting values in accordance with the Absolute Maximum Rating System (IEC 134)

THERMAL RESISTANCE

DEVICE CHARACTERISTICS

= V

13-16

= 8,5 V; T

amb

= 25 °C; fi = 1 MHz; fm = 400 Hz; m = 30%; fif = 460 kHz; measured in test circuit of Fig.1;

unless otherwise speciﬁed

Supply voltage V

= V

13-16

max. 20 V

Total power dissipation P

tot

max. 875 mW

Input voltage V

14-15

 max. 12 V

−V

14-16

, −V

15-16

max. 0,6 V

14-16

, V

15-16

max. VPV

Input current I

, I15 max. 200 mA

Operating ambient temperature range T

amb

−40 to + 80 °C

Storage temperature range T

stg

−55 to + 150 °C

Junction temperature T

max. + 125 °C

From junction to ambient R

th j-a

= 80 K/W

PARAMETER SYMBOL MIN. TYP. MAX. UNIT

Supplies

Supply voltage V

= V

13-16

7,5 8,5 18 V

Supply current I

= I

15 23 30 mA

R.F. stage and mixer

Input voltage (d.c. value) V

14-16

, V

15-16

− VP/2 − V

R.F. input impedance at V

< 300 µVR

14-16

, R

15-16

− 5,5 − kΩ

14-16

, C

15-16

− 25 − pF

R.F. input impedance at V

> 10 mV R

14-16

, R

15-16

− 8 − kΩ

14-16

, C

15-16

− 22 − pF

I.F. output impedance R

1-16

500 −−kΩ

1-16

− 6 − pF

Conversion transconductance

before start of a.g.c. I

1/Vi

− 6,5 − mA/V

Maximum i.f. output voltage, inductive

coupling to pin 1 V

1-13(p-p)

− 5 − V

D.C. value of output current (pin 1)

at V

= 0 V I

− 1,2 − mA A.G.C. range of input stage − 30 − dB R.F. signal handling capability:

input voltage for THD = 3% at m = 80% V

i(rms)

− 500 − mV

May 1984 6

Philips Semiconductors Product speciﬁcation

AM receiver circuit TDA1072A

Oscillator

Frequency range f

osc

0,6 − 60 MHz

Oscillator amplitude (pins 11 to 12) V

11-12

− 130 150 mV External load impedance R

12-11(ext)

0,5 − 200 kΩ

External load impedance for no oscillation R

12-11(ext)

−−60 Ω Ripple rejection at V

P(rms)

= 100 mV;

= 100 Hz

(RR = 20 log [V

13-16/V11-16

]) RR − 55 − dB

Source voltage for switching diodes (6 × V

11-16

− 4,2 − V D.C. output current (for switching diodes) −I

0 − 20 mA

Change of output voltage at

∆I11= 20 mA (switch to maximum load) ∆V

11-16

− 0,5 − V

Buffered oscillator output

D.C. output voltage V

10-16

− 0,7 − V Output signal amplitude V

10-16(p-p)

− 320 − mV Output impedance R

− 170 −Ω Output current −I

10(peak)

−−3mA

I.F., a.g.c. and a.f. stages

D.C. input voltage V

3-16

, V

4-16

− 2,0 − V I.F. input impedance R

3-4

2,4 3 3,9 kΩ

3-4

− 7 − pF I.F. input voltage for

THD = 3% at m = 80% V

3-4

− 90 − mV Voltage gain before start of a.g.c. V

3-4/V6-16

− 68 − dB A.G.C. range of i.f. stages: change of

3-4

for 1 dB change of V

o(af)

;

3-4(ref)

= 75 mV ∆V

3-4

− 55 − dB A.F. output voltage at V

3-4(if)

= 50 µVV

o(af)

− 130 − mV A.F. output voltage at V

3-4(if)

= 1 mV V

o(af)

− 310 − mV A.F. output impedance (pin 6) Z

−3,5 − kΩ

Indicator driver

Output voltage at V

= 0 mV;

L(9)

= 2,7 kΩ V

9-16

− 20 150 mV Output voltage at V

= 500 mV;

L(9)

= 2,7 kΩ V

9-16

2,5 2,8 3,1 V

Load resistance R

L(9)

1,5 −−kΩ

PARAMETER SYMBOL MIN. TYP. MAX. UNIT

+ 14 hidden pages