PHILIPS S9171 User Manual [fr]

S91xx/S90xx

31 2

1 2

4 5

1 2

PlusBasic

2 31

4 5

8 9 10

ENGLISH 12 ESPAÑOL 38 FRANÇAIS 66 ITALIANO 94 PORTUGUÊS 122 PORTUGUÊS DO BRASIL 151 TÜRKÇE 179

S91XX, S90XX

ENGLISH

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benet from the support that Philips

offers, register your product at www.philips.com/welcome. Please read this user manual, as it contains information about the features of this shaver as well as some tips to make shaving easier and more enjoyable.

General description (Fig. 1)

1 Comb for beard styler attachment 2 Click-on beard styler attachment 3 Click-on trimmer attachment 4 Click-on shaving unit 5 On/off button 6 Socket for small plug 7 Exclamation mark 8 Replacement reminder 9 Battery charge indicator 10 Travel lock symbol 11 Cleaning reminder 12 Replacement symbol 13 SmartClean system 14 Cap of SmartClean system 15 On/off button 16 Cleaning symbol 17 Drying symbol 18 Ready symbol 19 Charge symbol 20 Cleaning cartridge for SmartClean system 21 Adapter 22 Small plug 23 Retaining ring holder 24 Pouch

ENGLISH 13

Important

Read this user manual carefully before you use the shaver and the SmartClean system. Save this user manual for future reference.

Danger

- Keep the adapter dry.

Warning

- The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this causes a hazardous situation.

- The shaver and the SmartClean system are not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of these appliances by a person responsible for their safety.

- Children should be supervised to ensure that they do not play with the shaver and the SmartClean system.

- Always unplug the shaver before you clean it under the tap.

Caution

- Never immerse the SmartClean system in water nor rinse it under the tap.

Never use water hotter than 80°C to rinse the shaver.

- Do not use the shaver, SmartClean system, adapter or any other part if it is damaged, as this may cause injury. Always replace a damaged adapter or part with one of the original type.

- Only use the SmartClean system with the original cleaning cartridge.

- Always place the SmartClean system on a stable, level and horizontal surface to prevent leakage.

ENGLISH14

- Always make sure that the cartridge compar tment is closed before you use the SmartClean system to clean or charge the shaver.

- When the SmartClean system is ready for use,

do not move it to prevent leakage of cleaning uid.

- The SmartClean system thoroughly cleans but does not disinfect your shaver, therefore do not share the shaver with others.

- Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance.

- Water may leak from the socket at the bottom of the shaver when you rinse it. This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver.

Compliance with standards

- This shaver is waterproof and complies with the internationally approved safety regulations. It is suitable for use in the bath or shower and for cleaning under the tap. For safety reasons, the shaver can therefore only be used cordlessly.

- The shaver and the SmartClean system comply with all applicable standards and regulations

regarding exposure to electromagnetic elds.

General

- The adapter is equipped with an automatic voltage selector and is suitable for mains voltages ranging from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe low voltage of less than 24 volts.

- Maximum noise level: Lc = 69dB(A)

ENGLISH 15

The display

Note: Before you use the shaver for the rst time, remove the protective foil from the display.

- S91XX/S90XX

Charging

- Charging takes approx. 1 hour.

Note: This appliance can only be used cordlessly.

- When the shaver is connected to the mains,

you hear a sound. First the bottom light ashes

white then lights up white continuously. Then the

second light ashes and then lights up continuously,

and so on until the shaver is fully charged.

- Quick charge: When the bottom light stops

ashing and lights up continuously, the shaver

contains enough charge for one shave.

Battery fully charged

Note: This appliance can only be used cordlessly. Note: When the battery is full, the display switches

off automatically after 30 minutes. When you press the on/off button during or after charging, you hear a sound to indicate that the shaver is still connected to the mains.

- When the battery is fully charged, all lights of the battery charge indicator light up white continuously.

ENGLISH16

Battery low

- When the battery is almost empty, the bottom

light ashes orange and you hear a sound.

Remaining battery capacity

- The remaining battery capacity is indicated by the lights of the battery charge indicator that light up continuously.

Cleaning reminder

For optimal shaving performance, we advise you to clean the shaver after every use.

- When you switch off the shaver, the cleaning

reminder ashes to remind you to clean the

shaver.

Travel lock

You can lock the shaver when you are going to travel. The travel lock prevents the shaver from being switched on by accident.

Activating the travel lock

1 Press the on/off button for 3 seconds to enter

the travel lock mode.

, While you activate the travel lock, the travel lock

symbol lights up white continuously. When the travel lock is activated, the shaver produces a

sound and the travel lock symbol ashes.

ENGLISH 17

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

, The travel lock symbol ashes and then lights up

continuously.

The shaver is now ready for use again.

Note: You can also deactivate the travel lock by connecting the appliance to the mains.

Replacing shaving heads

For maximum shaving performance, we advise you to replace the shaving heads every two years.

- The appliance is equipped with a replacement reminder which reminds you to replace the shaving heads. The replacement reminder lights up white continuously and the arrows ash white. You hear a beep to indicate you have to replace the shaving heads.

Note: After replacing the shaving heads, you need to reset the shaver by pressing the on/off button for 7 seconds.

Exclamation mark

Blocked shaving heads

- If the shaving heads are blocked, the exclamation mark lights up orange continuously. The replacement reminder and the cleaning reminder

ash white alternately and you hear a sound. In

this case, the motor cannot run because the shaving heads are soiled or damaged.

- When this happens, you have to clean the shaving heads or replace them.

ENGLISH18

Overheating

- If the appliance overheats during charging,

the exclamation mark ashes orange.

- When this happens, the shaver automatically switches off. Charging continues once the appliance is back to the normal temperature.

Charging

Charging takes approx. 1 hour. A fully charged shaver has a shaving time of up to 50 minutes.

Note: You cannot use the appliance while charging.

Charge the shaver before you use it for the rst

time and when the display indicates that the battery is almost empty .

Charging with the adapter

1 Make sure the appliance is switched off. 2 Insert the small plug into the appliance (1)

and put the adapter in the wall socket (2).

Charging in the SmartClean system

1 Put the small plug in the SmartClean system. 2 Put the adapter in the wall socket. 3 Hold the shaver upside down above the holder.

Make sure the front of the shaver points towards the SmartClean system.

ENGLISH 19

4 Place the shaver in the holder (1), tilt the

shaver backwards (2) and press down the top cap to connect the shaver (‘click’) (3).

Note: The battery symbol lights up to indicate the appliance is charging.

Using the shaver

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you

expect and your skin may even become slightly irritated. This is normal. Your skin and beard need time to adapt to any new shaving system. We advise you to shave regularly (at least 3 times a week) with this shaver for a period of 3 weeks to allow your skin to adapt to the new shaver.

Tip: To ensure the best result, we advise you to pre-trim your beard if you have not shaved for 3 days or longer.

Note: This appliance can only be used cordlessly.

1 Press the on/off button once to switch on the

shaver.

, The display lights up for a few seconds.

2 Move the shaving heads over your skin in

circular movements.

- Do not make straight movements.

3 Press the on/off button once to switch off the

shaver.

, The display lights up for a few seconds and then

shows the remaining battery charge.

ENGLISH20

Wet shaving

You can also use this shaver on a wet face with shaving foam or shaving gel. To shave with shaving foam or shaving gel, follow the steps below:

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel to your skin.

3 Rinse the shaving unit under the tap to ensure

that the shaving unit glides smoothly over your skin.

4 Press the on/off button once to switch on the

shaver.

5 Move the shaving heads over your skin in

circular movements.

Note: Rinse the shaver under the tap regularly to ensure that it continues to glide smoothly over your skin.

6 Dry your face and thoroughly clean the

shaver after use (see chapter ‘Cleaning and maintenance’).

Note: Make sure you rinse all foam or shaving gel off the shaver.

ENGLISH 21

Using the click-on attachments

Using the trimmer attachment

You can use the trimmer attachment to groom your sideburns and moustache.

1 Pull the shaving unit straight off the appliance.

Note: Do not twist the shaving unit while you pull it off the appliance.

2 Insert the lug of the trimmer attachment into

the slot in the top of the shaver. Then press down the trimmer attachment to attach it to the appliance (‘click’).

3 Press the on/off button once to switch on the

appliance.

, The display lights up for a few seconds.

4 You can now start trimming. 5 Press the on/off button once to switch off the

appliance.

, The display lights up for a few seconds to show

the remaining battery charge.

6 Pull the trimmer attachment straight off the

appliance.

Note: Do not twist the trimmer attachment while you pull it off the appliance.

7 Insert the lug of the shaving unit into the slot

in the top of the appliance. Then press down the shaving unit to attach it to the appliance (‘click’).

ENGLISH22

Using the beard styler attachment

1 Make sure the appliance is switched off. 2 Pull the shaving unit straight off the appliance.

Note: Do not twist the shaving unit while you pull it off the appliance.

3 Insert the lug of the beard styler

attachment into the slot in the top of the appliance. Then press down the beard styler attachment to attach it to the appliance (‘click’).

Using the beard styler attachment with comb

You can use the beard styler attachment with the

comb attached to style your beard at one xed

setting, but also at different length settings. The hair length settings on the beard styler attachment correspond to the remaining hair length after cutting and range from 1 to 5mm.

1 Slide the comb straight into the guiding

grooves on both sides of the beard styler attachment (‘click’).

2 Press the length selector and then push it

to the left or right to select the desired hair length setting.

3 Press the on/off button once to switch on the

appliance.

4 You can now start styling your beard.

ENGLISH 23

Using the beard styler attachment without comb

You can use the beard styler attachment without the comb to contour your beard, moustache, sideburns or neckline.

1 Pull the comb off the beard styler attachment.

Note: Grab the comb in the centre to pull it off the beard styler attachment. Do not pull at the sides of the comb.

2 Press the on/off button once to switch on the

appliance.

3 You can now start contouring your beard,

moustache, sideburns or neckline.

Cleaning and maintenance

Cleaning the shaver in the SmartClean system

The SmartClean system comes in two types:

- SmartClean system Basic has one phase: the rinsing phase.

- SmartClean system Plus has two phases: the rinsing phase and the drying phase.

ENGLISH24

Preparing the SmartClean system for use

Do not tilt the SmartClean to prevent leakage.

Note: Hold the SmartClean while you prepare it for use.

1 Put the small plug in the back of the

SmartClean system.

2 Put the adapter in the wall socket. 3 Press the button on the side of the SmartClean

system (1) and lift the top part of the

SmartClean system (2).

4 Pull the seal off the cleaning cartridge.

5 Place the cleaning cartridge in the SmartClean

system.

6 Push the top part of the SmartClean system

back down (‘click’).

ENGLISH 25

Using the SmartClean system

Always make sure to shake excess water off the

shaver before you place it in the SmartClean.

1 Hold the shaver upside down above the holder.

Make sure the front of the shaver points

towards the SmartClean system.

2 Place the shaver in the holder (1), tilt the

shaver backwards (2) and press down the top

cap to connect the shaver (‘click’) (3).

, The battery symbol and the on/off button

start to ash, which indicates that the shaver is

charging.

3 Press the on/off button on the SmartClean

system to start the cleaning program.

, The on/off button and the rinsing symbol both

light up continuously.

Note: The rinsing phase takes approx. 10 minutes.

, SmartClean systems Plus only:

During the drying phase, the drying symbol lights up continuously.

Note: The drying phase takes approx. 4 hours.

ENGLISH26

, When the cleaning program has been completed,

the ready symbol lights up continuously.

, The battery symbol lights up continuously to

indicate that the shaver is fully charged.

Note: Charging takes approx. 1 hour. Note: If you press the on/off button of the SmartClean

system during the cleaning program, the program aborts. In this case, the rinsing or drying symbol stops ashing.

Note: If you remove the adapter from the wall socket during the cleaning program, the program aborts.

Note: 30 minutes after the cleaning program and charging have been completed, the SmartClean switches off automatically.

Replacing the cartridge of the SmartClean System

- Replace the cleaning cartridge when the

replacement symbol ashes orange or when you are no longer satised with the result.

1 Press the button on the side of the SmartClean

system (1) and lift the top part of the

SmartClean system (2).

2 Take the empty cleaning cartridge from the

SmartClean system and pour any remaining

cleaning uid out of the cleaning cartridge.

You can simply pour the cleaning uid down the sink.

3 Throw away the empty cleaning cartridge. 4 Unpack the new cleaning cartridge and pull the

seal off the cartridge.

ENGLISH 27

5 Place the new cleaning cartridge in the

SmartClean system.

6 Push the top part of the SmartClean system

back down (‘click’).

Cleaning the shaver under the tap

Clean the shaver after every shave for optimal shaving performance.

Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.

Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads.

1 Switch off the shaver. 2 Rinse the shaving unit under a warm tap for

some time.

3 Pull the shaving head holder off the bottom

part of the shaving unit.

ENGLISH28

4 Rinse the shaving head holder under a warm tap. 5 Carefully shake off excess water and let the

shaving head holder dry.

6 Reattach the shaving head holder to the

bottom part of the shaving unit (‘click’).

Thorough cleaning method

Make sure the appliance is switched off.

1 Pull the shaving head holder off the bottom

part of the shaving unit.

2 Place the retaining ring holder on the retaining

ring (1), turn it anticlockwise (2) and lift it off

the shaving head (3).

Remove the retaining ring from the retaining ring holder and repeat this process for the other retaining rings.

3 Remove the shaving heads from the shaving

head holder. Each shaving head consists of a

cutter and guard.

Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally put a cutter in the wrong shaving guard, it may take several weeks before optimal shaving performance is restored.

ENGLISH 29

4 Clean the cutter and guard under the tap.

5 After cleaning, place the cutter back into the

guard.

6 Put the shaving heads back into the shaving

head holder.

Note: Make sure the projections of the shaving heads t exactly into the recesses.

7 Place the retaining ring holder on the retaining

ring (1), place it on the shaving head (2) and turn

it clockwise (3) to reattach the retaining ring.

Repeat this process for the other retaining rings.

8 Reattach the shaving head holder to the

bottom part of the shaving unit.

Cleaning the click-on attachments

Cleaning the trimmer attachment

Clean the trimmer attachment every time you have used it.

1 Switch on the appliance with the trimmer

attachment attached.

ENGLISH30

2 Rinse the trimmer attachment under a hot tap

for some time.

3 Carefully shake off excess water and let the

trimmer attachment dry.

4 After cleaning, switch off the appliance.

Tip: For optimal trimmer performance, lubricate the trimmer teeth with a drop of sewing machine oil every six months.

Cleaning the beard styler attachment

Clean the beard styler attachment every time you have used it.

1 Pull the comb off the beard styler attachment. 2 Rinse the beard styler attachment and the comb

separately under a hot tap for some time.

3 Carefully shake off excess water and let the

beard styler attachment and comb dry.

4 Lubricate the teeth with a drop of sewing

machine oil every six months.

Storage

1 Store the shaver in the pouch supplied.

Note: We advise you to let the shaver dry before you store it in the pouch.

+ 178 hidden pages