Philips QC5770 User Manual [nl]

QC5770

C D

8 9

6 7

17 18 19

ENGLISH

4222.002.8064.1

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benet from the support that Philips offers,

clipping combs, an integrated precision trimmer and a

special hair thinning comb.

General description (Fig. 1)

A Cutting unit with regular trimmer and precision

trimmer

B Hair length adjustment ring C Thinning comb indicator D Hair length setting indicator E Charge level indicator F On/off button G Socket for appliance plug H Adapter I Appliance plug J Styling comb K Cleaning brush L Scissors M Hair thinning comb N Small hair clipping comb (3-22mm) O Large hair clipping comb (23-42mm)

Not shown: Storage case

Important

Read this user manual carefully before you use the appliance and save it for future reference.

Danger

- Make sure the adapter does not get wet.

Warning

- Check if the voltage indicated on the adapter and on the appliance corresponds to the local mains voltage before you connect the appliance.

- The adapter contains a transformer. Do not cut

off the adapter to replace it with another plug, as

this causes a hazardous situation.

- This appliance is not intended for use by persons

(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person responsible for their safety.

- Children should be supervised to ensure that they do not play with the appliance.

Caution

- Never immerse the appliance in water or any other

liquid, nor rinse it under the tap (Fig. 2).

- Use, charge and store the appliance at a temperature between 15°C and 35°C.

- Only use the adapter supplied.

- Do not use a damaged adapter.

- If the adapter, the cutting unit or one of the clipping

combs is damaged, always have it replaced with one

of the original type in order to avoid a hazard.

- Do not charge the appliance in a pouch or cassette.

- Do not use the appliance if one of the clipping

combs, the thinning comb or the cutting unit is damaged or broken, as this may cause injury.

- This appliance is only intended for clipping human scalp hair. Do not use it for any other purpose.

General

- The appliance is equipped with an automatic voltage selector and is suitable for mains voltages from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe low voltage of 15 volts.

- Noise level: Lc = 70 dB(A)

Electromagnetic elds (EMF)

This Philips appliance complies with all standards

regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this user

manual, the appliance is safe to use based on scientic

evidence available today.

Preparing for use Charging

Fully charging the appliance takes approx. 1 hour.

A fully charged appliance has a cordless clipping time of up to 1 hour.

1 Make sure the appliance is switched off.

2 Insert the appliance plug into the appliance (Fig. 3). 3 Insert the adapter into the wall socket.

, When you start charging the empty appliance,

the bottom segment of the charge level indicator

ashes orange. When the battery contains enough 

power for one clipping session of approx. 10

minutes, the bottom segment starts ashing blue.

, First the bottom segment of the charge level

indicator ashes blue, then the second segment and 

so on, until the appliance is fully charged.

, When the appliance is fully charged, all segments of

the charge level indicator light up blue continuously.

, If the fully charged appliance is still connected to

the mains after approx. 1 hour, the segments of the charge level indicator go out.

Battery low

When the battery is almost empty (when there are

approx. 10 clipping minutes left), the bottom segment of

the charge level indicator turns orange.

When you switch off the appliance, the bottom segment of the charge level indicator ashes for a few seconds.

Optimising the lifetime of the rechargeable battery

- After you have charged the appliance for the rst time, do not recharge it between clipping sessions.

Continue using it and recharge it only when the battery is (almost) empty.

- Do not keep the appliance plugged in continuously.

Corded clipping

When the rechargeable battery is empty, you can also run

the appliance from the mains. To use the hair clipper connected to the mains:

1 Switch off the hair clipper and connect it to the

mains.

2 Wait a few seconds and then switch on

the appliance.

Using the appliance Display indications

The display is activated when you press the on/of button and when you turn the length adjustment ring.

- During clipping, the display provides the following

information: (Fig. 4)

, The selected hair length (i.e. the remaining hair

length after clipping) in millimetres.

, ’--’ when no comb is attached to the appliance , ‘THIN’ when the thinning comb is attached to the

appliance

, The remaining battery charge. , ’E’ if the cutting unit is blocked.

Clipping with the small and large clipping comb

Make sure you use the right comb. If you use the thinning comb instead of the small or large clipping comb, only part of the hairs will be cut.

Select the small or large clipping comb, depending on the

desired hair length.

- The hair length settings are indicated in millimetres on the display of the appliance. The settings correspond to the remaining hair length after

cutting (Fig. 5).

- The small clipping comb cuts hair to a length between 3mm and 22mm in steps of 1mm.

- The large clipping comb cuts the hair to a length

between 23mm, and 42mm in steps of 1mm.

1 Slide the comb into the slot in the appliance

(‘click’) (Fig. 6).

2 To set the comb to the desired hair length setting,

turn the hair length adjustment ring to the left or to the right (Fig. 7).

, The display shows the selected hair length.

3 Switch on the appliance.

Tips

- We advise you to start clipping at the highest setting of the large clipping comb and to reduce the hair length in small steps until you reach the desired hair length.

- If a lot of hair has accumulated in the comb, remove the comb and blow and/or shake the hair out of it. Removing the comb does not change the set hair length setting.

- Write down the hair length settings you have used to create a certain hairstyle as a reminder for future clipping sessions.

Clipping with the thinning comb

Make sure you use the right comb. If you use the small or large clipping comb instead of the thinning comb, all the hair will be clipped at the same length.

- The thinning comb cuts hair to a length between 3mm and 22mm in steps of 1mm.

- With the thinning comb, you can give your haircut a natural look and it allows you to create a smooth transition between two different hair lengths.

- The thinning comb cuts only half of the hair

that enters the comb, which results in a natural look (Fig. 8).

Thinning an entire haircut

We advise you not to use the thinning comb for very short haircuts.

1 Slide the thinning comb into the slot in the

appliance (‘click’) (Fig. 6).

2 Set the thinning comb to a lower setting than the

one you just used for the small or large clipping comb to create the haircut.

How much lower the setting for the thinning comb should be depends on your hairstyle and hair length.

However, never use the thinning comb at a setting that

is lower than half the setting you used to create the

haircut. For example, if you used the large clipping comb at 30mm to create the haircut, do not use the thinning

comb at a setting lower than 15mm.

3 Switch on the appliance. 4 Move the thinning comb through the hair.

Make sure the thinning comb only touches each spot once, otherwise it cuts all the hair to the set hair length.

Creating a smooth transition between two hair lengths

If you have cut your hair to two different lengths, you

can use the thinning comb to create a smooth transition between these two lengths.

1 Slide the thinning comb into the slot in the

appliance (‘click’) (Fig. 6).

2 Set the thinning comb to a hair length setting that

is halfway between the two hair length settings you used to create the haircut.

For instance, if you have cut top part of the haircut to a

length of 20mm and the bottom part of the haircut to a

length of 10mm, set the thinning comb to 15mm.

3 Move the thinning comb upwards through the

transition between the two lengths (Fig. 9).

Make sure the thinning comb only touches each spot once, otherwise it cuts all the hair to the set hair length.

Clipping without comb

You can use the clipper without comb to contour the

neckline, the area around the ears and sideburns.

The comb keeps the cutting unit at a certain distance

from your head. This means that, if you use the clipper without comb, your hair is cut off very close to the skin.

1 To remove the comb, pull it off the

appliance (Fig. 10).

Never pull at the exible top of the comb. Always pull at

the bottom part.

2 Switch on the appliance. 3 Hold the appliance with the cutting unit pointing

upwards and make downward strokes with the regular trimmer (the broad side of the cutting unit).

Be careful, the trimmer removes every hair it touches.

Using the precision trimmer

The precision trimmer is only half as wide as the regular trimmer. It therefore allows more precise contouring of

the neckline, the area around the ears and sideburns.

1 To use the precision trimmer, simply turn the

cutting unit 180° until the precision trimmer points towards the front of the appliance (Fig. 11).

Note: You can also turn the cutting element 90° clockwise or anticlockwise if this makes it easier to trim certain areas.

2 Switch on the appliance.

4222.002.8064.1

3 Hold the appliance with the cutting unit pointing

upwards and make downward strokes with the precision trimmer (the narrow side of the cutting unit).

Be careful, the trimmer removes every hair it touches.

Cleaning

Clean the appliance every time you have used it.

Never use scouring pads, abrasive cleaning agents or aggressive liquids such as alcohol, petrol or acetone to clean the appliance.

Only clean the appliance and the adapter with the cleaning brush supplied.

Note: This appliance does not need any lubrication.

1 Make sure the appliance is switched off and

disconnected from the mains.

2 Pull the comb off the appliance (Fig. 10). 3 Clean the cutting unit with the cleaning brush

supplied. Also brush away any hairs that have

collected in the openings under the cutting

unit (Fig. 12).

Note: If the cutting unit falls off the appliance, you can reattach it. Place the cutting unit back onto the appliance and press it down until you hear it lock into position with

TWO clicks.

Storage

1 Put the appliance in the storage case supplied. 2 Store the appliance in a safe and dry place.

Note: Do not store the appliance while it is still connected to the mains.

Environment

- Do not throw away the appliance with the normal

household waste at the end of its life, but hand it in

at an ofcial collection point for recycling. (Fig. 13)

- The built-in rechargeable battery contains substances that may pollute the environment. Always remove the battery before you discard and hand in the

appliance at an ofcial collection point. Dispose of the battery at an ofcial collection point for batteries. If you have trouble removing the battery, you can

also take the appliance to a Philips service centre. The staff of this centre will remove the battery for you and will dispose of it in an environmentally safe

way (Fig. 14).

Removing the rechargeable battery

Only remove the rechargeable battery if it is completely empty.

Do not connect the appliance to the mains again after you have opened it.

1 Disconnect the appliance from the mains and let

the appliance run until the motor stops.

2 Pull the cutting unit off the appliance. 3 To remove the front panel, insert a screwdriver

between the front panel and the appliance (Fig. 15).

4 Undo the screw behind the front panel (Fig. 16). 5 Insert a screwdriver between the front housing and

the back housing of the appliance (Fig. 17).

6 Remove the entire front housing (Fig. 18). 7 Undo the four screws that fasten the printed circuit

board (Fig. 19).

8 Pull out the printed circuit board with rechargeable

battery (Fig. 20).

9 Cut the wires that connect the printed circuit

board with rechargeable battery to the motor (Fig. 21).

Guarantee and service

If you need service or information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Consumer

Care Centre in your country (you nd its phone number in the worldwide guarantee leaet). If there is no Consumer Care Centre in your country, go to your local

Philips dealer.

+ 6 hidden pages