Philips QC5125, QC5120, QC5115 User Manual [tr]

QC5125, QC5120, QC5115

1

H

A

B G C

D F

E

2

5

1

2

8

1

2

3

4

6

7

9

10

11	12	13
14	15	16

2	2

1

1

English

Introduction

Congratulations on your purchase and welcome to

Philips!To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.

General description (Fig. 1)

AHair clipping comb

BLength setting selector

CCutting element

DOn/off slide

ESocket for appliance plug

FAppliance plug

GAdapter

HCleaning brush

Important

Read this user manual carefully before you use the appliance and save it for future reference.

Danger

-- Make sure the adapter does not get wet.

Warning

-- Check if the voltage indicated on the adapter and on the appliance corresponds to the local mains voltage before you connect the appliance.

-- The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this causes a hazardous situation.

-- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

-- Children should be supervised to ensure that they do not play with the appliance.

Caution

-- Never immerse the appliance in water or any other liquid, nor rinse it under the tap.

-- Do not use the appliance in the bath or in the shower.

-- Use and store the appliance at a temperature between 15°C and 35°C.

-- Only use the appliance in combination with the adapter supplied.

-- If the adapter is damaged, always have it replaced with one of the original type in order to avoid a hazard.

-- Do not use the appliance if the cutting element or the hair clipping comb is damaged or broken, as this may cause injury.

-- This appliance is only intended for clipping human scalp hair. Do not use it for any other purpose.

General

-- The adapter transforms 220-240 volts to a safe low voltage of less than 24 volts.

-- This is appliance is not rechargeable and can only be operated from the mains.

Compliance with standards

This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today.

Using the appliance

1Insert the appliance plug into the appliance (Fig. 2).

2Put the adapter in the wall socket.

Clipping with hair clipping comb

Note: Make sure your hair is clean and dry. Do not use the appliance on freshly washed hair.

1Comb your hair with a styling comb in the direction of hair growth.  (Fig. 3)

2Slide the hair clipping comb into the guiding grooves of the appliance (‘click’) (Fig. 4).

Make sure that the arms of the comb have been properly slid into the grooves on both sides.

3Press the length setting selector (1) and then move the hair clipping comb up or down (2) to set the desired length setting (Fig. 5).

2

,, The corresponding hair length is visible on the side of the comb.

Length settings

With the hair clipping comb attached, the appliance can cut hair to 10 different lengths:

Hair lengths in mm	Hair lengths in inches
3	1/8
5	3/16
7	9/32
9	3/8
11	7/16
13	1/2
15	5/8
17	21/32
19	3/4
21	7/8

4Slide the on/off slide upwards to switch on the appliance (Fig. 6).

5Place the hair clipping comb on the scalp and move the appliance through the hair slowly.

Tips

-- Start clipping at the highest length setting of the hair clipping comb and reduce the length setting gradually.

-- Write down the length settings you have used to create a certain hairstyle as a reminder for future clipping sessions.

-- To clip in the most effective way, move the appliance against the direction of hair growth.

-- Since hair grows in different directions, you need to move the appliance in different directions as well

(upward, downward or across) (Fig. 7).

-- Make overlapping passes over the head to ensure that the appliance catches all the hairs that need to be cut.

-- Make sure that the flat part of the hair clipping comb is fully in contact with the scalp to obtain an even clipping result.

-- To achieve a good result with curly, sparse or long hair, you can use a styling comb to guide the hair towards the appliance.

-- Regularly remove cut hair from the hair clipping comb. If a lot of hair has accumulated in the comb, remove it from the appliance and blow and/or shake the hair out of it.

Clipping without hair clipping comb

You can use the appliance without hair clipping comb to clip your hair very close to the skin (0.8mm) or to contour the neckline and the area around the ears.

1To remove the hair clipping comb, press the length setting selector (1), move the comb upwards and then pull it off the appliance (2).  (Fig. 8)

2Comb the hair ends over the ears before you start to contour the hairline.

3Slide the on/off slide upwards to switch on the appliance (Fig. 6).

4Tilt the appliance in such a way that only one edge of the cutting element touches the hair ends.  (Fig. 9)

5Only cut the hair ends.The hairline has to be close to the ear.

6To contour the neckline and the sideburns, turn the appliance and make downward strokes (Fig. 10).

7Move the appliance slowly and smoothly. Follow the natural hairline.

Cleaning

Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as alcohol, petrol or acetone to clean the appliance.

Only clean the appliance and the adapter with the cleaning brush supplied.

Do not use any sharp objects to clean the appliance.

Clean the appliance after every use.

1Make sure the appliance is switched off and disconnected from the mains.

2To remove the comb, press the length setting selector (1), move the comb upwards and then pull it off the appliance (2).  (Fig. 8)

3Push the middle part of the cutting unit upwards with your thumb until it opens (Fig. 11).

4Clean the cutting unit with the cleaning brush supplied (Fig. 12).

5Clean the inside of the appliance with the cleaning brush supplied (Fig. 13).

Note:The appliance does not need any lubrication.

Replacement

The cutting unit, the adapter and the hair clipping comb are replaceable.

Replacing the cutting unit

Replace the cutting unit if it is damaged or worn. Only replace the cutting unit with an original Philips cutting unit.

1Push the middle part of the cutting unit upwards with your thumb until it opens and then pull it off the appliance (Fig. 14).

2Place the lug of the new cutting unit in the slot and push the cutting unit onto the appliance (‘click’) (Fig. 15).

Environment

-- Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment (Fig. 16).

Guarantee and service

If you need service or information or if you have a problem, please visit the Philips website at www.philips. com or contact the Philips Consumer Care Centre

in your country (you find its phone number in the worldwide guarantee leaflet). If there is no Consumer

Care Centre in your country, go to your local Philips dealer.

4222.002.8086.2