Philips QC 5070, QC 5090 User Manual [fa]

234

ENGLISH 6

FRANÇAIS 12

ESPAÑOL 18

28

34

QC5090, QC5070

á«Hô©dG

v<ñUã

Introduction

Dear Customer, you have made the right choice! Your new Philishave
super-easy hair clipper adapts to the contours of the head and enables
comfortable use. To enjoy using the hair clipper we advise you to read
the following information.

General description

A Large comb
B Small comb
C Precision trimmer (QC5090 only)
D Main cutting element
E On/off slide
F Result indicator (indicates the hair length after cutting)
G Length lock (locks the hair length setting)
H Cleaning brush
I Adapter
J Appliance plug
K Scissors
L Styling comb

Important

◗ Read these instructions for use carefully before using the

appliance and save them for future reference.

◗ Check if the voltage indicated on the adapter corresponds to the

local mains voltage before you connect the appliance.

◗ This appliance is suitable for mains voltages from 220 to 240 volts.
◗ Only use the adapter supplied.
◗ The adapter contains a transformer. Do not cut off the adapter to

replace it with another plug, as this will cause a hazardous situation.

◗ Do not use a damaged adapter.
◗ If the adapter is damaged, always have it replaced by one of the

original type in order to avoid a hazard.

◗ Do not use the appliance when one of the attachments is

damaged or broken as this may cause injury.

◗ Use, charge and store the appliance at a temperature between

15c and 35c (fig. 1).

ENGLISH6

◗ Keep the appliance and the adapter dry (fig. 2).
◗ Keep the appliance out of the reach of children.
◗ This appliance is only intended for clipping human hair. Do not

use it for any other purpose.

◗ Do not charge in pouch or cassette.

Charging

Charge the appliance for 8 hours (NiCd battery) or 12 hours (NiMh
battery) before you start using it for the first time.
A fully charged appliance has a cordless clipping time of up to
35 minutes (NiCd battery) or 50 minutes (NiMh battery).

Do not charge the appliance for more than 24 hours.

1 Make sure the appliance is switched off while charging.
2 Insert the appliance plug into the appliance (fig. 3).
3 Insert the adapter into the wall socket.

◗ The charging light will go on to indicate that the appliance is

charging (fig. 4).

Optimising the lifetime of the battery

After the appliance has been charged for the first time, do not recharge
it between clipping sessions. Continue using it and recharge it only
when the battery is (almost) empty.

- Discharge the battery completely twice a year by letting the motor
run until it stops.

- Do not keep the appliance plugged into a wall socket all the time.

- If the appliance has not been used for a long time, it must be
recharged for 8 hours (NiCd battery) or 12 hours (NiMh battery).

Corded clipping

Do not run the appliance from the mains when the battery is fully
charged.

ENGLISH 7

◗ To use the hair clipper connected to the mains: switch the hair

clipper off, connect it to the mains and wait a few seconds before
switching it on.

Using the appliance

Also see the quick-start CD-ROM.

Clipping with comb attachment

◗ The hair length after cutting is indicated in millimetres on the

result indicator (fig. 5).

◗ The hair length after cutting is only visible when one of the

combs is attached. Use the small comb for a length of 3-21 mm
and use the large comb for a length of 23-41 mm.

1 Slide the comb attachment into the guiding grooves of the

appliance ('click') (fig. 6).

Make sure that the arms of the comb attachment have been properly
slid into the grooves on both sides.

2 Set the comb to the desired hair length by turning the length lock

(fig. 7).

3 Switch the appliance on (fig. 8).

Choose the appropriate hair cutting method on the quick-start CD-ROM.

ENGLISH8

Large comb

hair length

23 mm

26 mm

29 mm

32 mm

35 mm

38 mm

41 mm

Small comb

hair length

3 mm

6 mm

9 mm

12 mm

15 mm

18 mm

21 mm

Tips

- We advise you to start clipping at the highest setting of the large
comb and to reduce the hair length in small steps until you reach
the desired hair length.

- If a lot of hair has accumulated in the comb, remove the comb
attachment and blow and/or shake the hair from the comb.
Removing the comb does not change the selected hair length
setting.

- Write down the hair length settings used to create a certain
hairstyle as a reminder for future clipping sessions.

Clipping without comb attachment:

You can use the clipper without comb attachment to contour the
neckline and the area around the ears. You can also find instructions
and tips on quick-start CD-ROM.

◗ Remove the comb attachment by pulling it off the appliance

(fig. 9).

Never pull at the flexible top of the comb attachment. Always pull at
the bottom part.

◗ The comb attachment keeps the cutting unit at a certain distance

from your head. This means that, if you use the clipper without
the comb attachment, your hair will be cut off very close to the
skin.

◗ For precise contouring and defining:

1 Push the middle part of the cutting unit upwards with your

thumb until it opens and then pull it off the appliance (fig. 10).

Be careful that the cutting unit does not fall to the floor.

2 Place the lug of the precision trimmer into the slot and push the

unit back onto the appliance ('click') (fig. 11).

ENGLISH 9

Cleaning

Clean the appliance every time you have used it.

Do not use abrasives, scourers or liquids such as alcohol, petrol or
acetone to clean the appliance.

The appliance and the adapter may only be cleaned with the brush
supplied.

1 Make sure the appliance is switched off and disconnected from

the mains when you start cleaning it.

2 Remove the comb attachment by pulling it off the appliance

(fig. 9).

3 Push the middle part of the cutting unit upwards with your

thumb until it opens and then pull it off the appliance (fig. 10).

Be careful that the cutting unit does not fall to the floor.

4 Clean the cutting unit with the brush supplied (fig. 12).
5 Also clean the inside of the appliance with the brush supplied

(fig. 13).

6 Place the lug of the cutting unit into the slot and push the unit

back onto the appliance ('click') (fig. 11).

This appliance does not need any lubrication.

Replacement

A worn or damaged cutting unit should only be replaced with an
original Philips cutting unit.

◗ Push the middle part of the cutting unit upwards with your

thumb until it opens and then pull it off the appliance (fig. 10).

Be careful that the cutting unit does not fall to the floor.

◗ Place the lug of the new cutting unit into the slot and push the

unit back onto the appliance ('click') (fig. 11).

ENGLISH10

Environment

Remove the battery when you discard the appliance. Do not throw the
battery away with the normal household waste, but hand it in at an
official collection point. You can also take the appliance to a Philips
service centre, which will remove the battery for you and will dispose
of it in an environmentally safe way.

Only remove the battery if it is completely empty.

1 Disconnect the appliance from the mains and let the appliance

run until the motor stops.

2 Push the middle part of the cutting unit upwards with your

thumb until it opens and then pull it off the appliance (fig. 10).

Be careful that the cutting unit does not fall to the floor.

3 Remove the upper housing part from the inner part of the

appliance by means of a screwdriver (fig. 14).

4 Separate the lower housing part from the appliance (fig. 15).
5 Remove the result indicator from the appliance (fig. 16).
6 Remove the battery by prying it out of the appliance (fig. 17).
7 Cut the wires and dispose of the battery in an environmentally

safe way.

Guarantee & service

If you need information or if you have a problem, please visit the Philips
website at www.philips.com or contact the Philips Customer Care
Centre in your country (you will find its phone number in the
worldwide guarantee leaflet). If there is no Customer Care Centre in
your country, turn to your local Philips dealer or contact the Service
Department of Philips Domestic Appliances and Personal Care BV.

ENGLISH 11

FRANÇAIS12

Introduction

Cher consommateur, vous avez fait le bon choix! Votre nouvelle
tondeuse Philishave super-easy s'adapte aux contours de votre coiffure
en facilitant ainsi son utilisation. Afin de pouvoir utiliser au mieux la
tondeuse, nous vous conseillons de suivre les instructions ci-dessous.

Description générale

A Large guide de coupe
B Petit guide de coupe
C Tondeuse de précision (QC5090 uniquement)
D Elément de coupe
E Bouton coulissant marche/arrêt
F Indicateur de résultat (indique la longueur des cheveux après la

coupe)

G Verrou du réglage de hauteur de coupe (verrouille le réglage
choisi)

H Brosse de nettoyage
I Adaptateur
J Connecteur
K Ciseaux
L Peigne à coiffer

Important

◗ Avant d'utiliser l'appareil, lisez les instructions ci-dessous et

conservez ce mode d'emploi pour un usage ultérieur.

◗ Avant de brancher l'appareil, vérifiez que la tension indiquée sur

l'adaptateur correspond à la tension du secteur de votre
logement.

◗ Tension d'utilisation: 220V à 240V.
◗ Utilisez exclusivement l'adaptateur fourni.
◗ L'adaptateur est doté d'un transformateur. N'essayez pas de

remplacer la fiche de l'adaptateur pour éviter tout accident.

◗ N'utilisez pas un adaptateur endommagé.
◗ Lorsque l'adaptateur est endommagé, remplacez-le par un

adaptateur d'origine pour éviter tout accident.

◗ N'utilisez pas l'appareil si un des accessoires est endommagé ou