Philips PT849-26 operation manual
Always here to help you
Register your product and get support at
www.philips.com/welcome
PT848
1
16
1
2
3
4
5
6
11
7
10
15
14
13
12
8
9
ENGLISH 4
DANSK 20
DEUTSCH 36
ΕΛΛΗΝΙΚΑ 52
ESPAÑOL 69
SUOMI 85
FRANÇAIS 101
ITALIANO 117
NEDERLANDS 133
NORSK 149
PORTUGUÊS 165
SVENSKA 181
TÜRKÇE 197
PT848
4
ENGLISH
Introduction
Congratulations on your purchase and welcome to Philips!
To fully benet from the support that Philips offers, register your product at
www.philips.com/welcome. Please read this user manual, as it contains
information about the wonderful features of this shaver as well as some
tips to make shaving easier and more enjoyable.
General description (Fig. 1)
1 Protection cap
2 Shaving unit
3 Shaving unit release button
4 On/off button
5 Charging light
6 Cap of SmartClean system
7 SmartClean system
8 Replacement symbol
9 Cleaning cartridge for SmartClean system
10 Cleaning symbol
11 On/off button
12 Ready symbol
13 Charge symbol
14 Adapter
15 Trimmer release slide
16 Trimmer
Important safety information
Read this important information carefully before you use the appliance and
its accessories and save it for future reference. The accessories supplied
may vary for different products.
Danger
- Keep the adapter dry.
Warning
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
- This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by
children without supervision.
- Always unplug the shaver before you clean it under the tap.
- Always check the appliance before you use it. Do not use the appliance
if it is damaged, as this may cause injury. Always replace a damaged part
with one of the original type.
ENGLISH 5
Caution
- Never immerse the cleaning system or the charging stand in water
and do not rinse it under the tap.
- Never immerse the shaver in water. Do not use the shaver in the
bath or in the shower.
- Never use water hotter than 80°C to rinse the shaver.
- Only use this appliance for its intended purpose as shown in the
user manual.
- For hygienic reasons, the appliance should only be used by one person.
- Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the appliance.
- If your shaver comes with a cleaning system, always use the original
Philips cleaning uid (cartridge or bottle, depending on the type of
cleaning system).
- Always place the cleaning system on a stable, level and horizontal
surface to prevent leakage.
- If your cleaning system uses a cleaning cartridge, always make sure
that the cartridge compartment is closed before you use the cleaning
system to clean or charge the shaver.
- When the cleaning system is ready for use, do not move it to prevent
leakage of cleaning uid.
- Water may drip from the socket at the bottom of the shaver when
you rinse it. This is normal and not dangerous because all electronics
are enclosed in a sealed power unit inside the shaver.
Electromagnetic elds (EMF)
- This Philips appliance complies with all applicable standards and
regulations regarding exposure to electromagnetic elds.
General
- This shaver can be safely cleaned under the tap.
- The appliance is suitable for mains voltages ranging from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe low voltage of less than
24 volts.
- Maximum noise level: Lc = 69dB(A)
Charging
It takes approx. 1 hour to fully charge the shaver.
When you charge the shaver for the rst time or after a long period of
disuse, let it charge until the charging light lights up continuously.
A fully charged shaver provides up to 50 shaving minutes.
The shaving time may be less than 50 shaving minutes as a result of your
shaving behaviour, your cleaning habits or your beard type.
ENGLISH6
Charge indications
Battery low
- When the battery is almost empty (when there are only 5 or fewer
shaving minutes left), the charging light starts to ash orange.
- When you switch off the shaver, the charging light continues to ash
orange for a few seconds.
Quick charging
- When you start charging the empty battery, the charging light
alternately ashes orange and green. After approx. 3 minutes,
the charging light starts ashing green only. The shaver now contains
enough energy for a 5-minute shave.
Charging
- When the shaver is charging, the charging light ashes green.
Battery fully charged
- When the battery is fully charged, the charging light lights up
green continuously.
Note: After approx. 30 minutes, the battery light goes out to save energy.
Charging with the adapter
1 Put the small plug in the shaver.
2 Put the adapter in the wall socket.
, The charging light shows the charging status of the shaver
(see section ‘Charge indications’ in this chapter).
Charging in the SmartClean system
1 Put the small plug in the SmartClean system.
2 Put the adapter in the wall socket.
3 Press the top cap to be able to place the shaver in the holder
(‘click’).
ENGLISH 7
4 Hold the shaver upside down above the holder. Make sure the front
of the shaver points towards the SmartClean system.
1
3
5 Place the shaver in the holder (1), tilt the shaver backwards (2)
and press down the top cap to connect the shaver (‘click’) (3).
2
Note: The battery symbol lights up to indicate that the appliance is charging.
Using the shaver
Note: You can also use the shaver with cord by connecting it to the mains.
Shaving
1 Press the on/off button once to switch on the shaver.
2 Move the shaving heads over your skin. Make circular movements.
- Your skin may need 2 or 3 weeks to get accustomed to the
Philips shaving system.
3 Press the on/off button once to switch off the shaver.
4 Clean the shaver (see chapter ‘Cleaning and maintenance’).
Trimming
You can use the trimmer to groom your sideburns and moustache.
1 Push the trimmer slide downwards to open the trimmer.
2 Press the on/off button once to switch on the shaver.
, You can now start trimming
ENGLISH8
3 After trimming, switch off the trimmer and clean it
(see chapter ‘Cleaning and maintenance’). Then close the trimmer.
Cleaning and maintenance
Remove the detachable cord from the handheld part before cleaning this
part in water.
Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the appliance.
- Clean the shaver after every shave for optimal shaving performance.
- Regular cleaning guarantees better shaving performance.
- For the best cleaning results, we advise you to use the Philips Cleaning
spray (HQ110).
- Be careful with hot water. Always check if the water is not too hot,
to prevent your hands from getting burnt.
Note: Water may leak from the socket at the bottom of the shaver when you
rinse it. This is normal and not dangerous because all electronics are enclosed
in a sealed power unit inside the shaver.
Cleaning the shaver in the SmartClean system
Preparing the SmartClean system for use
Do not tilt the SmartClean to prevent leakage.
Note: Hold the SmartClean while you prepare it for use.
1 Put the small plug in the back of the SmartClean system.
2 Put the adapter in the wall socket.
3 Press the button on the side of the SmartClean system (1)
and lift the top part of the SmartClean system (2).
2
1
ENGLISH 9
4 Pull the seal off the cleaning cartridge.
5 Place the cleaning cartridge in the SmartClean system.
6 Push the top part of the SmartClean system back down (‘click’).
Using the SmartClean system
Always make sure to shake excess water off the shaver before you place
it in the SmartClean.
Note: If a lot of hairs have collected in the hair chamber, remove the hairs
before placing the shaver into the SmartClean. Open the shaving unit and
shake out excess hairs.
1 Press the top cap to be able to place the shaver in the holder
(‘click’).
2 Hold the shaver upside down above the holder. Make sure the front
of the shaver points towards the SmartClean system.
ENGLISH10
1
2
3
3 Place the shaver in the holder (1), tilt the shaver backwards (2)
and press down the top cap to connect the shaver (‘click’) (3).
, The battery symbol starts to ash, which indicates that the shaver
is charging.
4 Press the on/off button on the SmartClean system to start the
cleaning program.
, During the rinsing phase, the rinsing symbol will ash.
Note: The rinsing phase takes approx. 10 minutes.
, When the cleaning program has been completed, the ready symbol
lights up continuously.
, The battery symbol lights up continuously to indicate that the shaver
is fully charged.
Note: Charging takes approx. 1 hour.
Note: If you press the on/off button of the SmartClean system during the
rinsing phase, the program aborts. In this case, the rinsing symbol stops
ashing.
Note: If you remove the adapter from the wall socket during the rinsing phase,
the phase aborts.
Note: 30 minutes after the rinsing phase and charging have been completed,
the SmartClean switches off automatically.
5 To let the shaver dry, you can leave it in the SmartClean system
until your next shave. You can also remove the shaver from the
SmartClean system, shake off excess water, open the shaving unit and
let the shaver air dry.
2
1
Replacing the cartridge of the SmartClean System
- Replace the cleaning cartridge when the replacement symbol ashes
orange or when you are no longer satised with the result.
1 Press the button on the side of the SmartClean system (1) and lift
the top part of the SmartClean system (2).
ENGLISH 11
2 Take the empty cleaning cartridge from the SmartClean system and
pour any remaining cleaning uid out of the Cleaning cartridge.
You can simply pour the cleaning uid down the sink.
3 Throw away the empty cleaning cartridge.
4 Unpack the new cleaning cartridge and pull the seal off the cartridge.
5 Place the new cleaning cartridge in the SmartClean system.
6 Push the top part of the SmartClean system back down (‘click’).
Cleaning the shaving unit under the tap
1 Switch off the shaver and disconnect it from the mains.
2 Press the release button to open the shaving unit.
3 Rinse the shaving unit and hair chamber under a hot tap for
30 seconds.
Be careful with hot water. Always check if the water is not too hot,
to prevent your hands from getting burnt.
- Rinse the hair chamber and the inside of the shaving unit.
ENGLISH12
- Rinse the outside of the shaving unit.
4 Close the shaving unit and shake off excess water.
Be careful not to hit the shaving unit against anything while shaking
off excess water.
Never dry the shaving unit and the hair chamber with a towel or tissue,
as this may damage the shaving heads and the coupling spindles.
5 Open the shaving unit again and leave it open to let the shaver
dry completely.
Thorough cleaning
1 Switch off the shaver and disconnect it from the mains.
2 Press the release button to open the shaving unit.
3 Rinse the shaving unit and hair chamber under a hot tap for
30 seconds.
Be careful with hot water. Always check if the water is not too hot,
to prevent your hands from getting burnt.
- Rinse the hair chamber and the inside of the shaving unit.
- Rinse the outside of the shaving unit.
4 Pull the shaving unit off the shaver.
ENGLISH 13
B
A
5 Turn the lock anticlockwise (A) and remove the retaining frame (B).
6 Remove and clean one shaving head at a time.
Each shaving head consists of a cutter and a guard.
Note: Do not clean more than one cutter and guard at a time, since they are
all matching sets. If you accidentally mix up the cutters and guards, it may take
several weeks before optimal shaving performance is restored.
7 Remove the cutter from the shaving guard and clean it under the tap.
Then clean the inside and outside of the shaving guard under the tap.
8 Put the shaving heads back into the shaving unit.
Note: Make sure that the projections of the shaving heads t exactly into
the recesses.
A
9 Put the retaining frame back into the shaving unit (A) and turn the
lock clockwise (B).
B
ENGLISH14
10 Insert the lug of the shaving unit into the slot in the top of the shaver.
Then close the shaving unit.
Note: If the shaving unit does not close smoothly, check if you have inserted
the shaving heads properly and if the retaining frame is locked.
11 Shake off excess water.
Be careful not to hit the shaving unit against anything while shaking
off excess water.
Never dry the shaving unit and the hair chamber with a towel or tissue,
as this may damage the shaving heads and the coupling spindles.
12 Open the shaving unit again and leave it open to let the shaver
dry completely.
Cleaning the trimmer under the tap
Clean the trimmer every time you have used it.
1 Switch off the shaver and disconnect it from the mains.
2 Push the trimmer slide downwards to open the trimmer.
3 Clean the trimmer under the tap.
4 Close the trimmer (‘ click’).
Tip: For optimal trimming performance, lubricate the trimmer teeth with a
drop of sewing machine oil every six months.
ENGLISH 15
Storage
- Put the protection cap on the shaver after use to prevent damage and
to avoid dirt accumulation in the shaving heads.
Replacement
For maximum shaving performance, we advise you to replace the shaving
heads every two years.
Replacement reminder
The shaving head symbol will light up to indicate that the shaving heads
need to be replaced. Replace damaged shaving heads right away.
Only replace the shaving heads with original HQ8 Philips Shaving Heads.
1 The shaving head symbol lights up orange continuously.
2 Switch off the shaver. Disconnect the shaver from the mains and
remove it from the SmartClean System.
3 Press the release button to open the shaving unit.
4 Pull the shaving unit off the shaver.
B
5 Turn the lock anticlockwise (A) and remove the retaining frame (B).
6 Remove the shaving heads and place new ones in the shaving unit.
A
Note: Make sure that the projections of the shaving heads t exactly into
the recesses.
ENGLISH16
A
7 Put the retaining frame back into the shaving unit (A) and turn
the lock clockwise (B).
B
8 Insert the lug of the new shaving unit into the slot in the top of
the shaver. Then close the shaving unit.
Note: If the shaving unit does not close smoothly, check if you have inserted
the shaving heads properly and if the retaining frame is locked.
9 Press and hold the on/off button for 5 seconds to reset the
replacement reminder on the shaver. The orange light goes out.
5 sec.
Ordering accessories
To retain the top performance of your shaver, make sure you clean it
regularly and replace its shaving heads at the recommended time.
Shaving heads
- We advise you to replace your shaving heads every two years.
Always replace with HQ8 Philips Shaving Heads
Cleaning
- Use Cleaning spray (HQ110) to clean the shaving heads thoroughly.
ENGLISH 17
Recycling
- This symbol on a product means that the product is covered by
European Directive 2012/19/EU.
- This symbol means that the product contains a built-in rechargeable
battery covered by European Directive 2006/66/EC which cannot be
disposed of with normal household waste. We strongly advise you to
take your product to an ofcial collection point or a Philips service
centre to have a professional remove the rechargeable battery.
- Inform yourself about the local separate collection system for electrical
and electronic products and rechargeable batteries. Follow local
rules and never dispose of the product and rechargeable batteries
with normal household waste. Correct disposal of old products and
rechargeable batteries helps prevent negative consequences for the
environment and human health.
Removing the rechargeable battery
Note: We strongly advise you to have a professional remove the
rechargeable battery.
Only remove the rechargeable battery when you discard the shaver.
Make sure the battery is completely empty when you remove it.
1 Disconnect the shaver from the mains.
2 Let the shaver run until it stops.
3 Undo the screws in the back of the shaver and in the hair chamber.
4 Remove the front panel and the back panel.
5 Bend the 6 hooks aside and take out the power unit.
Be careful, the hooks are sharp.
6 Remove the battery.
Be careful, the battery strips are sharp.
Do not connect the shaver to the mains again after you have removed
the rechargeable battery.
Guarantee and support
If you need information or support, please visit www.philips.com/
support or read the separate worldwide guarantee leaet. If there is no
Consumer Care Centre in your country, go to your local Philips dealer.
ENGLISH18
Guarantee restrictions
The shaving heads (cutters and guards) are not covered by the terms of
the international guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common problems you could
encounter with the appliance. If you are unable to solve the problem with
the information below, contact the Consumer Care Centre in your country.
Problem Possible cause Solution
The shaver does
not shave as well as
it used to.
The shaver does
not work when I
press the on/off
button.
Water leaks from
the shaver after
cleaning.
The SmartClean
system does not
work when I press
the on/off button.
The shaver is not
entirely clean after
I clean it in the
SmartClean system.
The shaving heads are damaged
or worn.
Long hairs obstruct the shaving
heads.
You have not inserted the shaving
heads properly.
The rechargeable battery is
empty.
The temperature of the shaver is
too high. In this case, the shaver
does not work.
During cleaning, water may collect
between the inner body and the
outer shell of the shaver.
The SmartClean system is not
connected to the mains.
You have not placed the
shaver in the SmartClean
system properly, so there is no
electrical connection between
the SmartClean system and the
shaver.
The cleaning cartridge needs
replacement.
Replace the shaving heads
(see chapter ‘Replacement’).
Clean the shaving heads one by one
(see chapter ‘Cleaning and maintenance’).
Make sure that the projections of the shaving
heads t exactly into the recesses
(see chapter ‘Cleaning and maintenance’).
Recharge the battery (see chapter
‘Charging’) or connect the shaver to the
mains.
As soon as the temperature of the shaver
has dropped sufciently, you can switch on
the shaver again.
During rinsing some water may collect
between the power unit and the housing.
After rinsing this water ows out through
the socket. The power unit is completely
watertight so water cannot reach the
electronic parts of the shaver. Your shaver
continues to be absolutely safe.
Put the small plug in SmartClean system and
put the adapter in the wall socket.
Press down the top cap (‘click’) to ensure a
proper connection between the shaver and
the SmartClean system.
Replace the cleaning cartridge (see chapter
‘Cleaning and maintenance’).
Problem Possible cause Solution
ENGLISH 19
The shaver is not
fully charged after
I charge it in the
SmartClean system.
The cleaning cartridge is empty.
The replacement symbol ashes
to indicate you have to replace
the cleaning cartridge.
You have used another cleaning
uid than the original Philips
cleaning cartridge.
The drain of the cleaning
cartridge might be blocked.
You have not placed the shaver in
the SmartClean system properly.
Place a new cleaning cartridge in the
SmartClean system
(see chapter ‘Cleaning and maintenance’).
Only use the Philips cleaning cartridge.
Push the hairs down the drain with a
toothpick.
Press down the top cap (‘click’) to ensure a
proper connection between the shaver and
the SmartClean system.
20
DANSK
Introduktion
Tillykke med dit køb og velkommen til Philips! For at få fuldt udbytte
af den support, Philips tilbyder, skal du registrere dit produkt på
www.philips.com/welcome.
Vi beder dig læse brugervejledningen igennem, da den indeholder
oplysninger om shaverens unikke funktioner og tips til at gøre barbering
nemmere og sjovere.
Generel beskrivelse (g. 1)
1 Beskyttelseskappe
2 Skærhoved
3 Udløserknap til skærhoved
4 On/off-knap
5 Opladeindikator med lys
6 Hætte til SmartClean-system
7 SmartClean-system
8 Udskiftningssymbol
9 Rengøringspatron til SmartClean-system
10 Rengøringssymbol
11 On/off-knap
12 Klar-symbol
13 Opladningssymbol
14 Adapter
15 Udløser til trimmer
16 Trimmer
Vigtige sikkerhedsoplysninger
Læs disse vigtige oplysninger omhyggeligt igennem, før du bruger
apparatet og dets tilbehør, og gem oplysningerne til eventuel senere brug.
Det medfølgende tilbehør kan variere for de forskellige produkter.
Fare
- Hold adapteren tør.
Advarsel
- Adapteren indeholder en transformer. Adapteren må ikke klippes af og
udskiftes med et andet stik, da dette vil forårsage en farlig situation.
- Dette apparat kan bruges af børn fra 8 år og op og personer med
reducerede fysiske, sensoriske eller mentale evner eller manglende
viden eller erfaring, hvis de er blevet vejledt eller instrueret i brug af
apparatet på en sikker måde og forstår de involverede risici. Børn må
ikke lege med apparatet. Rengøring og brugervedligeholdelse må ikke
foretages af børn uden opsyn.
- Tag altid stikket ud af shaveren, inden den skylles under vandhanen.
- Kontroller altid apparatet, før du bruger det. Brug ikke apparatet,
hvis det er beskadiget, da dette kan forårsage personskade. Du skal
altid erstatte en beskadiget del med en tilsvarende original type.
DANSK 21
Forsigtig
- Kom aldrig rengøringssystemet eller opladeenheden ned i vand,
og undgå at skylle dem under hanen.
- Kom aldrig shaveren ned i vand. Brug ikke shaveren i badet eller under
bruseren.
- Rens aldrig shaveren med vand, der er varmere end 80°C.
- Brug kun apparatet til det tilsigtede formål som vist i
brugervejledningen.
- Af hygiejniske grunde bør apparatet kun anvendes af en og samme
person.
- Brug aldrig trykluft, skuresvampe eller skrappe rengøringsmidler som
f.eks. benzin, acetone eller lignende til rengøring af apparatet.
- Hvis din shaver leveres med et rengøringssystem, skal du altid bruge
den originale Philips rensevæske (i rensepatron eller aske,
afhængigt af typen af rengøringssystem).
- Placer altid rengøringssystemet på et stabilt, plant og vandret underlag
for at undgå lækage.
- Hvis dit rengøringssystem anvender en rensepatron, skal du altid
sørge for, at rummet til rensepatronen er lukket, før du bruger
rengøringssystemet til at rengøre eller oplade shaveren.
- For at undgå udsivende rensevæske må rengøringssystemet ikke yttes,
mens det er klar til brug.
- Når shaveren rengøres, kan der dryppe lidt vand ud af stikket i bunden.
Dette er helt normalt og ganske ufarligt, da al elektronikken
er indkapslet i en forseglet motorenhed inde i shaveren.
Elektromagnetiske felter (EMF)
- Dette Philips-apparat overholder alle branchens gældende standarder
og regler angående eksponering for elektromagnetiske felter.
Generelt
- Denne shaver kan skylles under rindende vand uden risiko.
- Apparatet kan tilsluttes netspændinger mellem 100 og 240 V.
- Adapteren omformer 100 - 240 Volt til en sikker lavspænding
under 24 Volt.
- Maks. støjniveau: Lc = 69 dB (A)
Opladning
Det tager ca. 1 time at oplade shaveren helt.
Når shaveren oplades for første gang eller efter en længere pause,
skal den oplade, indtil opladeindikatoren lyser konstant.
En fuldt opladet shaver giver op til 50 minutters barberingstid.
Barberingstiden er muligvis kortere end 50 minutter som følge af dine
barberingsvaner, dine rensevaner eller din skægtype.
DANSK22
Opladningsindikatorer
Lavt batteriniveau
- Når batteriet næsten er aadet (når der kun er 5 minutter eller færre
tilbage til barbering), lyser opladeindikatoren orange.
- Når du slukker for shaveren, fortsætter opladeindikatoren med at
blinke orange i nogle sekunder.
Lynopladning
- Når du starter opladningen af det tomme batteri, blinker
opladeindikatoren skiftevis orange og grønt. Efter ca. 3 minutter blinker
opladeindikatoren kun grønt. Shaveren har nu nok strøm til 5 minutters
barbering.
Opladning
- Når shaveren oplades, blinker opladeindikatoren grønt.
Batteri fuldt opladet
- Når batteriet er fuldt opladet, lyser opladeindikatoren konstant grønt.
Bemærk: Efter ca. 30 minutter slukker batteriindikatoren for at spare
på energien.
Opladning med adapter
1 Sæt det lille stik i shaveren.
2 Slut adapteren til stikkontakten.
, Opladeindikatoren viser opladningsstatus for shaveren
(se afsnittet “Opladningsindikatorer” i dette kapitel).
Opladning i SmartClean-systemet
1 Sæt det lille stik i SmartClean-systemet.
2 Slut adapteren til stikkontakten.
3 Tryk på den øverste hætte, så shaveren kan sættes i holderen (“klik”).
DANSK 23
4 Hold shaveren på hovedet over holderen. Sørg for, at forsiden af
shaveren peger mod SmartClean-systemet.
1
3
5 Sæt shaveren i holderen (1), vip shaveren bagud (2), og tryk ned på
den øverste hætte for at tilslutte shaveren (“klik”) (3).
2
Bemærk: Batterisymbolet lyser for at indikere, at apparatet oplades.
Brug af shaveren
Bemærk: Du kan også bruge shaveren med ledning ved at tilslutte
den til lysnettet.
Barbering
1 Tryk én gang på tænd/sluk-knappen for at tænde for shaveren.
2 Bevæg skærhovederne hen over huden i cirkulære bevægelser.
- Vær opmærksom på, at der kan gå 2-3 uger, før din hud helt har
vænnet sig til Philips’ barberingssystem.
3 Tryk én gang på tænd/sluk-knappen for at slukke for shaveren.
4 Rengør shaveren (se afsnittet “Rengøring og vedligeholdelse”).
Trimning
Trimmeren kan bruges til pleje af bakkenbarter og moustache.
1 Tryk trimmerens skydekontakt nedad for at åbne trimmeren.
2 Tryk én gang på tænd/sluk-knappen for at tænde for shaveren.
, Trimningen kan nu påbegyndes
DANSK24
3 Efter trimningen skal du slukke for trimmeren, og rense den
(se afsnittet “Rengøring og vedligeholdelse”). Luk derefter trimmeren.
Rengøring og vedligeholdelse
Tag den aftagelige netledning ud af håndholdte del, inden denne
del rengøres i vand.
Brug aldrig trykluft, skuresvampe eller skrappe rengøringsmidler som
f.eks. benzin, acetone eller lignende til rengøring af apparatet.
- Rengør shaveren efter hver barbering for at bevare den optimale
barberingsevne.
- Regelmæssig rengøring sikrer det bedste barberingsresultat.
- For at opnå det bedste rengøringsresultat anbefaler vi, at du bruger
Philips Cleaning Spray (HQ110).
- Vær forsigtig med varmt vand. Kontroller altid, at vandet ikke er for
varmt, så du ikke skolder dine hænder.
Bemærk: Når shaveren rengøres, kan der dryppe lidt vand ud af stikket
i bunden. Dette er helt normalt og ganske ufarligt, da al elektronikken er
indkapslet i en forseglet motorenhed inde i shaveren.
Rengøring af shaveren i SmartClean-systemet
Klargøring af SmartClean-systemet til brug
Vip ikke SmartClean for at undgå lækage.
Bemærk: Hold SmartClean-systemet, mens du klargør det til brug.
1 Isæt det lille stik på bagsiden af SmartClean-systemet.
2 Slut adapteren til stikkontakten.
3 Tryk på knappen på siden af SmartClean-systemet (1), og løft den
øverste del af SmartClean-systemet (2).
2
1
DANSK 25
4 Træk forseglingen af rengøringspatronen.
5 Placer rengøringspatronen i SmartClean-systemet.
6 Skub den øverste del af SmartClean-systemet ned på plads (“klik”).
Brug af SmartClean-systemet
Sørg altid for at ryste overskydende vand af shaveren, inden du placerer
den i SmartClean.
Bemærk: Hvis der har samlet sig mange hår i skægkammeret, skal du fjerne
hårene, inden du sætter shaveren i SmartClean-systemet. Åbn skærenheden,
og ryst overskydende hår af.
1 Tryk på den øverste hætte, så shaveren kan sættes i holderen (“klik”).
2 Hold shaveren på hovedet over holderen. Sørg for, at forsiden af
shaveren peger mod SmartClean-systemet.
DANSK26
1
2
3
3 Sæt shaveren i holderen (1), vip shaveren bagud (2), og tryk
ned på den øverste hætte for at tilslutte shaveren (“klik”) (3).
, Batterisymbolet begynder at blinke, hvilket angiver, at shaveren
oplades.
4 Tryk på SmartClean-systemets tænd/sluk-knap for at starte
renseprogrammet.
, Under skyllefasen blinker skyllesymbolet.
Bemærk: Skyllefasen tager ca. 10 minutter.
, Når renseprogrammet er fuldført, lyser klar-symbolet konstant.
, Batterisymbolet lyser konstant for at indikere, at shaveren er fuldt
opladet.
Bemærk: En fuld opladning tager ca. 1 time.
Bemærk: Hvis du trykker på SmartClean-systemets tænd/sluk-knap i løbet af
skyllefasen, afbrydes programmet. I så fald vil skyllesymbolet holde op med at
blinke.
Bemærk: Hvis du tager adapteren ud af stikkontakten i løbet af skyllefasen,
afbrydes fasen.
Bemærk: 30 minutter efter, at skyllefasen og opladningen er fuldført,
slukker SmartClean automatisk.
5 Du kan lade shaveren tørre i SmartClean-systemet indtil næste
barbering. Du kan også tage shaveren ud af SmartClean-systemet,
ryste overskydende vand af, åbne skærenheden og lade shaveren
lufttørre.
2
1
Udskiftning af SmartClean-systemets patron
- Udskift rengøringspatronen, når udskiftningssymbolet blinker orange,
eller når du ikke længere er tilfreds med resultatet.
1 Tryk på knappen på siden af SmartClean-systemet (1), og løft den
øverste del af SmartClean-systemet (2).
DANSK 27
2 Tag den tomme rengøringspatron ud af SmartClean-systemet,
og hæld eventuel resterende rensevæske ud af rengøringspatronen.
Rensevæsken hældes blot ud i vasken.
3 Smid den tomme rengøringspatron væk.
4 Udpak den nye rengøringspatron, og træk forseglingen af patronen.
5 Placer den ny rengøringspatron i SmartClean-systemet.
6 Skub den øverste del af SmartClean-systemet ned på plads (“klik”).
Rengøring af skærhovedet under rindende vand
1 Sluk for shaveren, og tag den ud af stikket.
2 Tryk på udløserknappen og luk skærhovedet op.
3 Skyl skærhovedet og skægkammeret i varmt rindende vand i
30 sekunder.
Vær forsigtig med varmt vand. Kontroller altid, at vandet ikke er for
varmt, så du ikke skolder dine hænder.
- Rens skægkammeret og indersiden af skærhovedet.
DANSK28
- Skyl skærhovedets yderside.
4 Luk skærhovedet, og ryst overskydende vand væk.
Pas på, at skærhovedet ikke støder mod andre ting, når du ryster
overskydende vand væk.
Skærhovedet og skægkammeret må ikke tørres med et håndklæde eller
køkkenrulle, da dette kan beskadige skærene og koblingsakslerne.
Åbn skærhovedet igen, og lad det stå åbent, indtil shaveren er helt tør.
5
Grundig rengøring
1 Sluk for shaveren, og tag den ud af stikket.
2 Tryk på udløserknappen og luk skærhovedet op.
3 Skyl skærhovedet og skægkammeret i varmt rindende vand
i 30 sekunder.
Vær forsigtig med varmt vand. Kontroller altid, at vandet ikke er for
varmt, så du ikke skolder dine hænder.
- Rens skægkammeret og indersiden af skærhovedet.
- Skyl skærhovedets yderside.
4 Træk skærhovedet af shaveren.
DANSK 29
B
A
5 Drej låsen mod uret (A), og tag samlerammen af (B).
6 Fjern og rens et skær ad gangen. Hvert skær består af en kniv og en
lamelkappe.
Bemærk: Rens kun ét skær ad gangen, da knive og lamelkapper er slebet
parvis. Kommer man ved en fejltagelse til at blande knive og lamelkapper,
kan det tage ere uger, før shaveren igen barberer optimalt.
7 Fjern skæret fra skærkappen, og rengør den under vandhanen.
Rengør derefter inder- og ydersiden af skærkappen under vandhanen.
8 Sæt skærene tilbage i skærhovedet.
Bemærk: Sørg for, at de små tappe passer præcist ned i recesserne.
A
9 Sæt samlerammen tilbage i skærenheden (A),
og drej den med uret (B).
B
DANSK30
10 Placer tappen på skærhovedet i rillerne øverst på shaveren.
Luk derefter skærhovedet.
Bemærk: Hvis skærhovedet ikke lukker uden modstand, skal du kontrollere,
at du har placeret skærene korrekt, og at samlerammen er låst.
11 Ryst overskydende vand af.
Pas på, at skærhovedet ikke støder mod andre ting, når du ryster
overskydende vand væk.
Skærhovedet og skægkammeret må ikke tørres med et håndklæde eller
køkkenrulle, da dette kan beskadige skærene og koblingsakslerne.
12 Åbn skærhovedet igen, og lad det stå åbent, indtil shaveren er
helt tør.
Rengøring af trimmeren under vandhanen
Rens trimmeren, hver gang den har været brugt.
1 Sluk for shaveren, og tag den ud af stikket.
2 Tryk trimmerens skydekontakt nedad for at åbne trimmeren.
3 Rengør trimmeren under vandhanen.
4 Luk trimmeren med et klik.
Tip: Smør trimmerens tænder med en dråbe symaskineolie hver 6. måned for
at bevare optimal trimmerfunktion.
Loading...