Philips PCF5001T, PCF5001U, PCF5001H Datasheet

DATA SH EET

Product speciﬁcation Supersedes data of 1995 Apr 27 File under Integrated Circuits, IC17

1997 Mar 04

INTEGRATED CIRCUITS

PCF5001

POCSAG Paging Decoder

1997 Mar 04 2

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

CONTENTS

1 FEATURES 2 APPLICATIONS 3 GENERAL DESCRIPTION 4 ORDERING INFORMATION 5 BLOCK DIAGRAMS 6 PINNING 7 FUNCTIONAL DESCRIPTION

7.1 The PCF5001 supports two basic modes of operation

7.2 The POCSAG paging code

7.3 Modes and states of the decoder

7.4 Decoding of the POCSAG data stream

7.5 Generation of output signals

7.6 Alerter

7.7 Silent call storage and Repeat mode

7.8 Duplicate Call Suppression

7.9 LED indicator

7.10 Vibrator output

7.11 Start-up alert

7.12 Serial communication interface

7.13 Message data transfer

7.14 Call Data output on LED

7.15 Serial communication call data format

7.16 Data conversion

7.17 Memory Organization

7.18 Description of the Special Programmed Function (SPF) bits

7.19 EEPROM Write operation

7.20 EEPROM Read operation

7.21 Read-back operation via Microcontroller Interface

7.22 Voltage converter

7.23 Test modes of the decoder

7.23.1 Board test mode

7.23.2 Pager Test Mode (Type Approval Mode)

8 LIMITING VALUES 9 DC CHARACTERISTICS 10 DC CHARACTERISTICS (WITH VOLTAGE

CONVERTER)

11 AC CHARACTERISTICS 12 TIMING CHARACTERISTICS 13 PROGRAMMING CHARACTERISTICS 14 APPLICATION INFORMATION 15 PACKAGE OUTLINES 16 SOLDERING

16.1 Introduction

16.2 Reflow soldering

16.3 Wave soldering

16.3.1 LQFP

16.3.2 SO

16.3.3 Method (LQFP and SO)

16.4 Repairing soldered joints

17 DEFINITIONS 18 LIFE SUPPORT APPLICATIONS

1997 Mar 04 3

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

1 FEATURES

• Wide operating supply voltage range (1.5 to 6.0 V)

• Extended temperature range: −40 to +85 °C (between

−40 to −10 °C, minimum supply voltage restricted

to 1.8 V)

• Very low supply current (60 µA typ. with

76.8 kHz crystal)

•

“CCIR radio paging Code No 1”

(POCSAG) compatible

• Programmable call termination conditions

• 512 and 1200 bits/s data rates (2400 bits/s with some

restrictions), see Section 7.4

• Improved ACCESS



synchronization algorithm

• Supports 4 user addresses (RICs) in two independent frames

• Eight different alert cadences

• Directly drives magnetic or piezo ceramic beeper

• High level alert requires only a single external transistor

• Optional vibrator type alerting

• Silent call storage, up to eight different calls

• Repeat alarm facility

• Programmable duplicate call suppression

• Interfaces directly to UAA2050T, UAA2080 and

UAA2082 digital paging receivers

• Programmable receiver power control for battery economy

• On-chip non-volatile EEPROM storage

• On-chip voltage converter with improved drive capability

• Serial microcontroller interface for display pager

applications

• Optional visual indication of received call data using a modified RS232 format

• Level shifted microcontroller interface signals

• Alert on low battery

• Optional out-of-range indication.

2 APPLICATIONS

• Alert-only pagers, display pagers

• Telepoint

• Telemetry/data receivers.

3 GENERAL DESCRIPTION

The PCF5001 is a fully integrated low-power decoder and pager controller. It decodes the CCIR radio paging Code No.1 (POCSAG-Code) at 512 and 1200 bits/s data rates. The PCF5001 is fabricated in SACMOS technology to ensure low power consumption at low supply voltages.

4 ORDERING INFORMATION

Note

1. When using IR reflow soldering it is recommended that the Drypack instructions in the

“Quality Reference Handbook”

(order number 9397 750 00192) are followed.

TYPE NUMBER

PACKAGE

NAME DESCRIPTION VERSION

PCF5001T SO28 plastic small outline package; 28 leads; body width 7.5 mm SOT136-1 PCF5001H LQFP32

(1)

plastic low proﬁle quad ﬂat package; 32 leads; body 7 × 7 × 1.4 mm SOT358-1

1997 Mar 04 4

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

5 BLOCK DIAGRAMS

Fig.1 Block diagram (SO28; SOT136-1).

handbook, full pagewidth

PD PS

DO DS

PCF5001T

RECEIVER 

ENABLE

CONTROL

OSCILLATOR

VOLTAGE

CONVERTER

POWER-ON 

RESET

TEST

CONTROL

STATUS

CONTROL

CLOCK

RECOVERY

CLOCK

GENERATION

DATA OUTPUT

CONTROL

DIGITAL INPUT

FILTER

SYNC

CONTROL

TIMING

CONTROL

DECODER AND

ERROR CORRECTION

CONTROL

BL BSSR SK ON IE

EEPROM

MEMORY

EEPROM

CONTROL

ALERT

GENERATION

CONTROL

BATTERY LOW 

CONTROL

SERIAL DATA PROCESSOR

26 27

AH AL OR OM OL AI

TS TTFLCP CN

X1 X2

12 15 25 16 13 23

ref

9 10

7 8

17 4

3 2 1 28 11 18 21202219 24 6

MCD454

1997 Mar 04 5

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

Fig.2 Block diagram (LQFP32; SOT358-1).

handbook, full pagewidth

PD PS

DO DS

PCF5001H

RECEIVER 

ENABLE

CONTROL

OSCILLATOR

VOLTAGE

CONVERTER

POWER-ON 

RESET

TEST

CONTROL

STATUS

CONTROL

CLOCK

RECOVERY

CLOCK

GENERATION

DATA OUTPUT

CONTROL

DIGITAL INPUT

FILTER

SYNC

CONTROL

TIMING

CONTROL

DECODER AND

ERROR CORRECTION

CONTROL

BL BSSR SK ON IE

EEPROM

MEMORY

EEPROM

CONTROL

ALERT

GENERATION

CONTROL

BATTERY LOW 

CONTROL

SERIAL DATA PROCESSOR

10 11

AH AL OR OM OL AI

TS TTFLCP CN

X1 X2

26 29

9 30 27

ref

19 22

31 16

15 14 13 12 25 32 4 3 5 1 8 18

MLB045

n.c.2n.c.7n.c.20n.c.

1997 Mar 04 6

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

6 PINNING

SYMBOL

DESCRIPTION

PCF5001T

(SOT136-1)

PCF5001H

(SOT358-1)

ref

1 13 Microcontroller interface reference voltage input/output. The LOW level of

pins FL, DS, DO, OR, BL, AI, ON, SK, SR and IE is related to the voltage on V

ref

. May be driven from an external negative voltage source or must be connected to VSS, if pins CN and CP are left open-circuit. When the on-chip voltage converter is used, this pin provides a doubled negative output voltage.

CN 2 14 Voltage converter external shunt capacitance, negative side. Connect the

negative side of the shunt capacitor to this pin, if the on-chip voltage converter function is used.

CP 3 15 Voltage converter external shunt capacitor, positive side. Connect the

positive side of the shunt capacitor to this pin, if the on-chip voltage converter function is used.

4 16 Main positive power supply. This pin is common to all supply voltages and

is referred to as 0 V (common).

DI 5 17 Serial data input (POCSAG code). The serial data signal train applied to

this pin is processed by the decoder. Pulled LOW by an on-chip pull-down when the receiver is disabled (RE = LOW).

BS 6 18 Battery-low indication input. The decoder samples this input during

synchronization scan, when it is in ON or SILENT status and the receiver is enabled (RE = HIGH). A battery-low condition is assumed, if the decoder detects four consecutive samples HIGH. An audible battery-low indication is made by the decoder, when operating in ON status. Normally LOW by the operation of an on-chip pull-down.

PD 7 19 EEPROM programming data input and output. Normally HIGH by the

operation of an on-chip pull-up. During programming of the on-chip EEPROM, PD is a bidirectional data and control signal.

PS 8 22 EEPROM programming strobe input. Normally LOW by the operation of

an on-chip pull-down. During programming of the on-chip EEPROM, PS is a unidirectional control input.

X1 9 23 Crystal oscillator input. Connect a 32768 Hz or 76800 Hz crystal and a

biasing resistor between this pin and X2. In addition, provide a load capacitance to V

, which may also be used for frequency tuning.

X2 10 24 Crystal oscillator output. Return connection for the external crystal and

resistor at X1.

TS 11 25 Scan test mode enable input. Always LOW by operation of an on-chip

pull-down.

AH 12 26 Alert HIGH-level output. This output can directly drive an external bipolar

transistor to control HIGH-level alerting in conjunction with AL, by means of an alerter or beeper.

OL 13 27 LED indication output. This output can directly drive an external bipolar

transistor to control the visual alert function by means of an LED. It may also be used for visual indication of received call data during call reception.

1997 Mar 04 7

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

RE 14 28 Receiver enable output. May be used to control the paging receiver power

control input, to minimize power consumption. The decoder provides a HIGH-level at this pin, when receiver operation is requested. Each time the decoder does not require any input data at DI the receiver enable output is LOW.

AL 15 29 Alert LOW-level output. Open drain alert output in anti-phase to AH, to

provide LOW-level alerting. HIGH-level alerting is generated in conjunction with AH.

OM 16 30 Vibrator output. This output can directly drive an external bipolar transistor

to control a vibrator type alerter.

17 31 Main negative supply voltage.

TT 18 32 Test mode enable input. Always LOW by operation of an on-chip

pull-down.

IE 19 1 Interface enable input. While the interface enable input is active HIGH,

operation of the ON, SK, SR, AI, BL and OR inputs and outputs is possible. When IE is LOW the inputs do not respond to applied signals and the outputs are made high-impedance. In alert-only pager mode the interface enable input does not have any effect on the operation of inputs ON, SK and SR, but IE must be referenced to LOW or HIGH.

SK 20 3 SILENT state control input. The SILENT control input selects the decoder

ON status (LOW-level) or SILENT status (HIGH-level), if the ON input is active HIGH. An on-chip pull-up is provided, if the decoder has been programmed for ‘alert-only pager’ mode, whereby the pull-up is disabled for display pager mode. In ‘display pager’ mode status change is possible if the interface enable input (IE) is HIGH and the status is latched on the falling edge of IE.

SR 21 4 Status request and reset input. A HIGH-going pulse on this input causes

(a) status indication cadence to be generated, if the decoder is not alerting or (b) resetting of a call alert, repeated call alert or battery-low alert, if active or (c) triggers the call store re-alert facility, if repeat mode is active. In ‘display pager’ mode operation of SR is possible only if the interface control input is active. Normally LOW by the operation of an on-chip pull-down.

ON 22 5 On/off control input. The on/off control input selects the decoder ON status

(HIGH-level) or OFF status (LOW-level). An on-chip pull-up resistor is provided, if the decoder has been programmed for ‘alert-only pager’ mode, but the pull-up resistor is disabled for ‘display pager’ mode. In ‘display pager’ mode, status change is possible if the interface enable input (IE) is HIGH and the status is latched on the falling edge of IE.

AI 23 6 Alarm input. A HIGH-level on this input causes generation of a continuous

HIGH-level alert via AH and AL outputs, if the decoder operates in ON status or OFF status. In addition, the LED output is active independent from the decoder status, but in accordance with AI. Pulsing the input may be used to modulate the alert and LED indication. Normally LOW in ‘alert-only pager’ mode by operation of an on-chip pull-down.

SYMBOL

DESCRIPTION

PCF5001T

(SOT136-1)

PCF5001H

(SOT358-1)

1997 Mar 04 8

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

BL 24 8 Battery-low indication output. If the decoder encounters a battery-low

condition a battery-low output latch is set HIGH. The battery-low output latch may be tested for a battery-low condition, whenever the interface enable input (IE) is active (HIGH), otherwise the battery-low output is made high-impedance. The battery-low output latch is reset only, by switching the decoder to OFF status.

OR 25 9 Out-of-range indication output. Whenever the decoder detects an

out-of-range condition an out-of-range output latch is set HIGH after expiry of the programmed out-of-range hold-off time selected by means of special programming (SPF06 and SPF07) of the EEPROM. The out-of-range latch may be tested for an out-of-range condition, whenever the interface enable input (IE) is active (HIGH), otherwise the out-of-range output is made high-impedance. The out-of- range output is reset by detection of a valid data transmission or by switching the decoder to OFF status.

DO 26 10 Serial interface data output. During normal decoder operation, accepted

calls and possibly subsequent message data are serially output via this pin in conjunction with the data strobe output (DS). This pin is also used to output the EEPROM contents upon special command, if the decoder is programmed for display pager.

DS 27 1 1 Serial interface data strobe output. Provides a clock signal for the received

call data and EEPROM data appearing at the data output (DO). Each time this output is LOW the data at DO is valid. Additional start and stop conditions allow easy identiﬁcation of data sequence start and end.

FL 28 12 Frequency reference output. When programmed for ‘display pager’ mode,

this output provides a clock reference with 16384 or 32768 Hz per second, selected by SPF32. See Chapter 7.

n.c. − 2, 7, 20, 21 Not connected.

SYMBOL

DESCRIPTION

PCF5001T

(SOT136-1)

PCF5001H

(SOT358-1)

1997 Mar 04 9

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

Fig.3 Pin configuration PCF5001T (SOT136-1).

handbook, halfpage

28 27 26 25 24 23

22 21 20 19 18 17 16 15

2 3 4

10 11 12 13 14

MCD455 - 1

DS DO OR BL AI ON SR SK IE TT

OM AL

PCF5001T

CN CP

X1 X2

ref

Fig.4 Pin configuration PCF5001H (SOT358-1).

handbook, halfpage

1 2 3 4 5 6 7 8

24 23 22 21 20 19 18 17

index corner

n.c.

SK SR ON

n.c.

ref

n.c.

VSSTT

PCF5001H

MLB048

7 FUNCTIONAL DESCRIPTION

The PCF5001 is a very low power Decoder and Pager Controller specifically designed for use in new generation radio pagers. The architecture of the PCF5001 allows for flexible application in a wide variety of radio pager designs.

The PCF5001 is fully compatible with

“CCIR radio paging

Code Number 1”

(also known as the POCSAG code) operating at the originally specified 512 bits/s data rate, and also at the newly specified 1200 bits/s data rate (2400 bits/s operation is also possible). The PCF5001 also offers features which extend the basic flexibility and efficiency of this code standard.

7.1 The PCF5001 supports two basic modes of

operation

In alert-only pager mode only a minimum number of external components are required to build a complete tone-only pager. Selection of operating states ON, OFF or SILENT is achieved using a slider switch interface.

In display pager mode the state input logic is switched to a bus interface structure. Received calls and messages are transferred to an external microcontroller via the serial microcontroller interface. A built-in voltage converter with increased drive capabilities can supply doubled supply voltage output, and appropriate logic level shifting on microcontroller interface signals is provided.

Upon reception of valid calls one of eight different call cadences is generated; upon status interrogation status indication tones make the current status of the decoder available to the user.

On-chip non-volatile 114-bit EEPROM storage is provided to hold up to four user addresses, two frame numbers and the programmed decoder configuration.

Synchronization to the input data stream is achieved using the improved ACCESS



algorithm, which allows for data synchronization and re-synchronization without preamble detection while minimizing battery power consumption by receiver power control. One of four error correction algorithms is applied to the received data to optimize the call success rate.

1997 Mar 04 10

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

7.2 The POCSAG paging code

A transmission using the

“CCIR Radio paging Code No. 1”

(POCSAG code) is constructed in accordance with the following rules (see Fig.5).

The transmission is started by sending a preamble, consisting of at least 576 continuously alternating bits (10101010...). The preamble is followed by an arbitrary number of batch blocks. Only complete batches are transmitted.

Each batch comprises 17 codewords of 32 bits each. The first codeword is a synchronization codeword with a fixed pattern. The sync word is followed by 8 frames (0 to 7) of 2 codewords each, containing message information. A codeword in a frame can either be an address, message or idle codeword.

Idle codewords also have a fixed pattern and are used to fill empty frames or to separate messages.

Address codewords are identified by an MSB at logic 0 and are coded as shown in Fig.5. A user address or RIC consists of 21 bits. Only the upper 18 bits are encoded in the address codeword (bits 2 to 19). The lower 3 bits designate the frame number (0 to 7) in which the address is transmitted.

Four different call types (‘numeric’, ‘alphanumeric’ and two ‘alert only’ types) can be distinguished. The call type is determined by two function bits in the address codeword (bits 20 and 21).

Alert-only calls consist only of a single address codeword. Numeric and alphanumeric calls have message codewords following the address. A message causes the frame structure to be temporarily suspended. Message codewords are sent until the message is completed, with only the sync words being transmitted in their expected positions.

Message codewords are identified by an MSB at logic 1 and are coded as shown in Fig.5. The message information is stored in a 20-bit field (bits 2 to 21).

The standard data format is determined by the call type: 4 bits per digit for numeric messages and 7 bits per (ASCII) character for alphanumeric messages.

Each codeword is protected against transmission errors by 10 CRC check bits (bits 22 to 31) and an even-parity bit (bit 32). This permits correction of a maximum of 2 random errors or up to 3 errors in a burst of 4 bits (a 4-bit burst error) per codeword.

Fig.5 POCSAG code structure.

handbook, full pagewidth

PREAMBLE BATCH 1 BATCH 2 BATCH 3 LAST BATCH

SYNC | CW CW | CW CW | . . . . . | CW CW

FRAME 0 FRAME 1 FRAME 7

10101 . . . 10101010

Address code-word

Message code-word

0 18-bit address 2 function bits 10 CRC bits P

1 20-bit message 10 CRC bits P

MCD456

1997 Mar 04 11

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

7.3 Modes and states of the decoder

The PCF5001 supports two basic operating modes:

• ‘Alert-only pager’ mode

• ‘Display pager’ mode.

Two further modes, the programming mode and the test mode, are implemented to program and verify the EEPROM contents and to support pager production and approval tests, respectively.

In ‘alert-only pager’ mode no external microcontroller is required, see Fig.22. A three position slider switch interface is provided to select the internal state of the decoder. The decoder performs regular scanning of the switch inputs to detect a status change. A push-button interface is provided on the SR input, which is used as input for user acknowledgment actions and status interrogation. Upon reception of valid calls, tone alert cadences are generated. A call storage is provided to store calls received while operating in SILENT status and to recall cadences upon ‘repeat’ mode operation. The voltage doubler and the frequency reference output are disabled in this mode.

In ‘display pager’ mode the PCF5001 operates as decoder and pager controller in combination with an external microcontroller (see Fig.23). The internal states of the decoder are determined by appropriate logic levels on the status inputs. A bus type interface structure is used to interface the decoder to the microcontroller. The decoder's on-chip voltage converter provides doubled supply voltage output to provide a higher supply voltage to the microcontroller and any additional hardware. The logic levels of the interface's input and output signals are level shifted to allow for direct coupling between microcontroller

and the decoder. Upon detection of a valid call, address and message information are transferred to the external microcontroller using the serial microcontroller interface. In addition, appropriate call alert cadences are generated.

If the decoder is in one of the two operating modes, it is always in one of the following three internal states:

• OFF status. This is the power saving, inactive status of

the PCF5001. The paging receiver is disabled, no decoding of input data takes place. However, the crystal oscillator is kept running to ensure that scanning of the status inputs/status switch is maintained to allow changing into one of the following two active states.

• ON status. This is the normal active status of the

decoder. Incoming calls are compared with the user addresses stored in the internal EEPROM. Upon detection of valid calls, alert cadences and LED indication are generated and data is shifted out at the serial microcontroller interface.

• SILENT status. The SILENT status is the same as the

ON status with the exception that valid calls no longer cause generation of call alert cadences. Instead, if programmed as ‘alert-only pager’, the decoder stores up to eight different calls and generates appropriate alert cadences after the decoder has been put back into the ON status. However, special SILENT override calls will cause generation of alert cadences, if enabled.

The decoder operating status is selected as indicated in Table 1.

When programmed for ‘alert-only pager’ a switch debounce period is applied to the status inputs. For status change and status interrogation in ‘display pager’ mode, see Figs 6 and 7.

Table 1 Truth table for decoder operating status

Note

1. The EEPROM transfer mode applies to ‘display pager’ mode only.

ON INPUT SK INPUT OPERATING STATUS

0 0 OFF 0 1 OFF (EEPROM transfer mode; note 1) 10ON 1 1 SILENT

1997 Mar 04 12

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

Fig.6 Status change in display pager mode.

INTERNAL 

STATUS

ON

tt t

STP STD STD

IEH

STH

MCD457 - 1

Fig.7 Status interrogation in display pager mode.

MCD458

tt t t t

STP STH SPD IEH STH

7.4 Decoding of the POCSAG data stream

The POCSAG coded input data stream is first noise filtered by a digital filter. From the filtered data a sampling clock synchronous to the data rate is derived. The PCF5001 supports 512 bits/s and 1200 bits/s data rates. This results in a 512 Hz or 1200 Hz sampling clock frequency, respectively. Synchronization on the POCSAG code structure is performed using the improved Philips ACCESS algorithm, which employs a state machine with six internal states.

A data rate of 2400 bits/s is possible if an external clock generator of 153.6 kHz is connected to X1. The minimum supply voltage is then −1.8 V.

The receiver enable output is activated a period equal to t

RXON

before the input data is actually needed. The decoder has first to achieve bit and word synchronization before it can receive calls. The algorithm searches first for the preamble and then for synchronization codeword patterns.

1997 Mar 04 13

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

This is carried out for the duration of 3 batches in

power-on mode or 1 batch (=preamble duration) in preamble receive mode. Error correction algorithms are

applied to the data before it is compared with preamble and synchronization codeword patterns. The synchronization process is terminated and thus data receive mode is entered as soon as synchronization codewords are seen at the beginning of each batch.

The decoder handles loss of synchronization in three steps:

1. If the decoder fails to detect the synchronization pattern at the beginning of the current batch it continues data reception as normal. This data fail mode is signalled in the message output when an address codeword was received, as shown in Table 4.

2. If also at the beginning of the next batch no synchronization codeword can be detected, the algorithm assumes a small bit shift in the fade recovery mode and performs more synchronization codeword checks around the expected position for the following 15 batches. Call reception is suspended.

3. If it fails to re-synchronize in the ‘fade recovery’ mode, the carrier off mode is selected, in which the decoder attempts to regain synchronization by bit-wise shifting its synchronization scan window. Using this technique re-synchronization is obtained within a continuous data stream of at least 18 batches without preamble detection.

In ‘data receive’ mode, the input data stream is sampled at the synchronization codeword position and the programmed frame positions. The received codewords are error corrected and then, if address codewords, compared with the stored user addresses related to that frame.

On detection of a valid call, the decoder performs the following three operations:

1. Set a store for call alert cadence generation according to the combination of the function bits in the accepted address codeword. The call alert cadence will not be generated before the call has been terminated.

2. Keep the receiver enable output (RE) active and receive subsequent message codewords, until any of the call termination criteria are fulfilled.

3. Trigger the serial message transfer by sending a start condition and transfer deformatted message codewords as attached to the address codeword via the serial microcontroller interface to an external microcontroller, followed by a stop condition.

Normally call termination is assumed, when a valid idle or address codeword is received. On reception of uncorrectable codewords, call termination takes place in accordance with conditions shown in Table 2.

Table 2 Call termination on error

Note

1. X = don’t care.

SPF12 SPF13 CALL TERMINATION EVENT

(1)

Any two consecutive codewords or the codeword directly following the address

codeword uncorrectable. 1 0 Any single codeword uncorrectable. 1 1 Any two consecutive codewords uncorrectable.

1997 Mar 04 14

Philips Semiconductors Product speciﬁcation

POCSAG Paging Decoder PCF5001

7.5 Generation of output signals

The PCF5001 provides output indications for call alert, repeat mode alert, out of range alert, battery-low alert, status indication alert and start-up alert. Some of the alert functions may be freely configured by programming of SPF bits within the EEPROM.

Table 3 shows the outputs which are used for special output indications, if the decoder operates in ON status.

Remark: reception of special SILENT override calls causes the decoder to generate call alert indication via AL and AH even if it operates in SILENT status.

Table 3 Output signals

Note

1. Entries in parenthesis are not valid, if the decoder operates in SILENT status.

ALERT FUNCTION

OUTPUT ACTIVE

(1)

AL AH OL OM OR BL

Start-up (yes) − yes yes −− Status indication yes −−−−− Call reception (yes) (yes) yes SPF11 −− Repeat mode (SPF16) (SPF16) SPF16 −−− Out-of-range −−SPF15 − yes − Battery-low (yes) (yes) −−−yes Alarm input (yes) (yes) yes −−−

7.6 Alerter

The PCF5001 provides the AL and AH outputs for acoustical LOW-level and HIGH-level signalling. LOW-level alerting is provided by the AL output only. For HIGH-level alerting both, AL and AH are active in anti-phase. The square-wave output signals produce tone alert cadences by means of a magnetic or piezo ceramic beeper. The alert frequency, 2048 Hz or 2731 Hz square-wave, is selected by programming of SPF31.

When valid calls are received while operating in ON status, the PCF5001 generates call alert cadences. The first four seconds are generated at LOW-level, a further twelve seconds are generated at HIGH-level. Alert tone generation and LED indication automatically terminate after sixteen seconds unless terminated by pulsing the status request and reset input (SR). Call alert generation is inhibited until completion of message codeword reception and the termination word is sent by the decoder. Call alert generation commences after an alert delay period, t

ALD

, at the earliest, see Fig.8. Call alert deletion is

possible during the alert delay period.

The call alert cadence is modulated according to the two function bits (FC) in the received address codeword, see Fig.9.

Valid calls received on RIC B or RIC D cause the alerter frequency to be warbled by means of an additional 16 Hz and 1024 Hz signal (respective 1365 Hz for SPF31 = 1) as opposed to RIC A and RIC C where no alert frequency warble takes place. Thus, eight different call cadences are distinguishable.

ON status interrogation by the status request and reset input (SR) the PCF5001 generates a status cadence at LOW-level, in accordance with the present internal decoder status (see Fig.10).

When detecting a battery-low condition the PCF5001 provides a battery-low indication. Operating in ON status causes generation of a battery-low alert at HIGH-level for sixteen seconds or until terminated by pulsing SR. Operating in SILENT status or ‘repeat’ mode the battery-low alert is stored and inhibited until switching to ON status.

+ 30 hidden pages