Philips PCF2104CU-2-F1, PCF2104CU-7-F1, PCF2104LU-2-F1, PCF2104LU-7-F1, PCF2104NU-2-F1 Datasheet

...

DATA SH EET

Product speciﬁcation Supersedes data of 1997 Apr 01 File under Integrated Circuits, IC12

1997 Dec 16

INTEGRATED CIRCUITS

PCF2104x

LCD controller/driver

1997 Dec 16 2

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

CONTENTS

1 FEATURES 2 APPLICATIONS 3 GENERAL DESCRIPTION

3.1 Packages

3.2 Available types 4 ORDERING INFORMATION 5 BLOCK DIAGRAM 6 PINNING 7 PIN FUNCTIONS

7.1 RS: register select (parallel control)

7.2 R/W: read/write (parallel control)

7.3 E: data bus clock (parallel control)

7.4 DB0 to DB7: data bus (parallel control)

7.5 C1 to C60: column driver outputs

7.6 R1 to R32: row driver outputs

7.7 VLCD: LCD power supply

7.8 OSC: oscillator

7.9 SCL: serial clock line

7.10 SDA: serial data line

7.11 SA0: address pin

7.12 T1: test pad 8 FUNCTIONAL DESCRIPTION

8.1 LCD bias voltage generator

8.2 Oscillator

8.3 External clock

8.4 Power-on reset

8.5 Registers

8.6 Busy Flag

8.7 Address Counter (AC)

8.8 Display data RAM (DDRAM)

8.9 Character generator ROM (CGROM)

8.10 Character generator RAM (CGRAM)

8.11 Cursor control circuit

8.12 Timing generator

8.13 LCD row and column drivers

8.14 Programming of MUX 1 : 16 displays with PCF2104x

8.15 Programming of MUX 1 : 32 displays with PCF2104x

8.16 Reset function

9 INSTRUCTIONS

9.1 Clear display

9.2 Return home

9.3 Entry mode set

9.3.1 I/D

9.3.2 S

9.4 Display on/off control

9.4.1 D

9.4.2 C

9.4.3 B

9.5 Cursor/display shift

9.6 Function set

9.6.1 DL (parallel mode only)

9.6.2 N, M

9.7 Set CGRAM address

9.8 Set DDRAM address

9.9 Read busy flag and address

9.10 Write data to CGRAM or DDRAM

9.11 Read data from CGRAM or DDRAM 10 INTERFACE TO MICROCONTROLLER

(PARALLEL INTERFACE)

11 INTERFACE TO MICROCONTROLLER

(I2C-BUS INTERFACE)

11.1 Characteristics of the I2C-bus

11.2 Bit transfer

11.3 Start and stop conditions

11.4 System configuration

11.5 Acknowledge

11.6 I2C-bus protocol 12 LIMITING VALUES 13 HANDLING 14 DC CHARACTERISTICS 15 AC CHARACTERISTICS 16 TIMING DIAGRAMS 17 APPLICATION INFORMATION

17.1 8-bit operation, 2 × 12 display using internal reset

17.2 4-bit operation, 2 × 12 display using internal reset

17.3 8-bit operation, 2 × 24 display

17.4 I2C operation, 2 × 12 display

17.5 Initializing by instruction

18 BONDING PAD LOCATIONS 19 DEFINITIONS 20 LIFE SUPPORT APPLICATIONS 21 PURCHASE OF PHILIPS I2C COMPONENTS

1997 Dec 16 3

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

1 FEATURES

• Single chip LCD controller/driver

• 1 or 2-line display of up to 24 characters per line, or

2 or 4 lines of up to 12 characters per line

• 5 × 7 character format plus cursor; 5 × 8 for kana (Japanese syllabary) and user-defined symbols

• On-chip: – generation of intermediate LCD bias voltages – oscillator requires no external components (external

clock also possible)

• Display data RAM: 80 characters

• Character generator ROM: 240 characters

• Character generator RAM: 16 characters

• 4 or 8-bit parallel bus or 2-wire I

C-bus interface

• CMOS/TTL compatible

• 32 row, 60 column outputs

• MUX rates 1 : 32 and 1 : 16

• Uses common 11 code instruction set

• Logic supply voltage range, VDD− VSS: 2.5 to 6 V

• Display supply voltage range, VDD− V

LCD

: 3.5 to 9 V

• Low power consumption.

• I2C-bus address: 011101 SA0.

2 APPLICATIONS

• Telecom equipment

• Portable instruments

• Point-of-sale terminals.

3 GENERAL DESCRIPTION

The PCF2104x integrated circuit is similar to the PCF2114x (described in the

“PCF2116 family”

data sheet)

but does not contain the high voltage generator of that device.

The PCF2104x is optimized for chip-on-glass applications. The ‘x’ in ‘PCF2104x’ represents a specific letter code for a character set in the character generator ROM (CGROM).

Two standard character sets are currently available, specified by the letters ‘C’ and ‘L’ (see Figs 5 and 6). Other character sets are available on request.

The PCF2104x is a low-power CMOS LCD controller and driver, designed to drive a split screen dot matrix LCD display of 1 or 2 lines by 24 characters or 2 or 4 lines by 12 characters with a 5 × 8 dot format. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD bias voltages which results in a minimum of external components and lower system power consumption. To allow partial V

shutdown the ESD protection system of the SCL and SDA pins does not use a diode connected to VDD.

The chip contains a character generator and displays alphanumeric and kana characters. The PCF2104x interfaces to most microcontrollers via a 4 or 8-bit bus, or via the 2-wire I2C-bus.

3.1 Packages

• PCF2104xU/2; chip with bumps in tray

• PCF2104xU/7; chip with bumps on tape.

For further details see Chapter 18.

3.2 Available types

• PCF2104CU/x: character set ‘C’ in CGROM

• PCF2104LU/x: character set ‘L’ in CGROM

• PCF2104NU/x: character set ‘N’ in CGROM.

4 ORDERING INFORMATION

TYPE NUMBER

PACKAGE

NAME DESCRIPTION VERSION

PCF2104CU/2 − chip with bumps in tray − PCF2104CU/7 − chip with bumps on tape − PCF2104LU/2 − chip with bumps in tray − PCF2104LU/7 − chip with bumps on tape − PCF2104NU/2 − chip with bumps in tray − PCF2104NU/7 − chip with bumps on tape −

1997 Dec 16 4

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

5 BLOCK DIAGRAM

Fig.1 Block diagram.

handbook, full pagewidth

SHIFT REGISTER

32-BIT

MGC627

CHARACTER GENERATOR

RAM

(CGRAM)

CHARACTERS

CHARACTER GENERATOR

ROM

(CGROM)

240

CHARACTERS

CURSOR + DATA CONTROL

SHIFT REGISTER

5 x 12-bit

DATA LATCHES

COLUMN DRIVERS

BIAS

VOLTAGE

GENERATOR

ROW DRIVERS

DISPLAY DATA RAM

(DDRAM) 80 CHARACTERS

5-20 81-96

ADDRESS

COUNTER (AC)

INSTRUCTION

DECODER

INSTRUCTION REGISTER (IR)

DATA

BUSY FLAG

78 8

I/O BUFFER

111

LCD

DISPLAY ADDRESS COUNTER

POWER - ON

RESET

TIMING

GENERATOR

OSCILLATOR

OSC

C1 to C60

R1 to R32

109-106

98 100 99

DB0 to DB3 DB4 to DB7 E

R/W

PCF2104x

SCL

110

SDA3SA0

101

105-102

80-21

1997 Dec 16 5

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

6 PINNING

SYMBOL FFC PAD TYPE DESCRIPTION

OSC 1 I oscillator/external clock input V

2 P logic supply voltage

SA0 3 I I

C-bus address pin input

4 P ground R8 to R5 5 to 8 O LCD row driver outputs R32 to R29 9 to12 O LCD row driver outputs R24 to R17 13 to 20 O LCD row driver outputs C60 to C1 21 to 80 O LCD column driver outputs R9 to R16 81 to 88 O LCD row driver outputs R25 to R28 89 to 92 O LCD row driver outputs R1 to R4 93 to 96 O LCD row driver outputs SCL 97 I I

C-bus serial clock input E 98 I data bus clock input RS 99 I register select input R/

W 100 I read/write input T1 101 I test pad input DB7 to DB0 102 to 109 I/O 8-bit bidirectional data bus input/output SDA 110 I/O I

C-bus serial data input/output

LCD

111 I LCD supply voltage input

7 PIN FUNCTIONS

7.1 RS: register select (parallel control)

RS selects the register to be accessed for read and write when the device is controlled by the parallel interface. RS = logic 0 selects the instruction register for write and the Busy Flag and Address Counter for read. RS = logic 1 selects the data register for both read and write. There is an internal pull-up on pin RS.

7.2 R/

W: read/write (parallel control)

R/W selects either the read (R/W = logic 1) or write (R/W = logic 0) operation when control is by the parallel interface. There is an internal pull-up on this pin.

7.3 E: data bus clock (parallel control)

The E pin is set HIGH to signal the start of a read or write operation when the device is controlled by the parallel interface. Data is clocked in or out of the chip on the negative edge of the clock. Note that this pin must be tied to logic 0 (V

) when I2C-bus control is used.

7.4 DB0 to DB7: data bus (parallel control)

The bidirectional, 3-state data bus transfers data between the system controller and the PCF2104x. DB7 may be used as the Busy Flag, signalling that internal operations are not yet completed. In 4-bit operations the 4 higher order lines DB4 to DB7 are used; DB0 to DB3 must be left open circuit. There is an internal pull-up on each of the data lines. Note that these pins must be left open circuit when I

C-bus control is used.

7.5 C1 to C60: column driver outputs

These pins output the data for pairs of columns. This arrangement permits optimized chip-on-glass (COG) layout for 4-line by 12 characters.

7.6 R1 to R32: row driver outputs

These pins output the row select waveforms to the left and right halves of the display.

7.7 V

LCD

: LCD power supply

Negative power supply for the liquid crystal display.

1997 Dec 16 6

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

7.8 OSC: oscillator

When the on-chip oscillator is used, this pin must be connected to VDD. An external clock signal, if used, is input at this pin.

7.9 SCL: serial clock line

Input for the I

C-bus clock signal.

7.10 SDA: serial data line

Input/output for the I

C-bus data line.

7.11 SA0: address pin

The hardware sub-address line is used to program the device sub-address for 2 different PCF2104xs on the same I

C-bus.

7.12 T1: test pad

Must be connected to V

. Not user accessible.

8 FUNCTIONAL DESCRIPTION (see Fig.1)

8.1 LCD bias voltage generator

The intermediate bias voltages for the LCD display are also generated on-chip. This removes the need for an external resistive bias chain and significantly reduces the system power consumption. The optimum levels depend on the multiplex rate and are selected automatically when the number of lines in the display is defined.

The optimum value of V

depends on the multiplex rate, the LCD threshold voltage (Vth) and the number of bias levels. The relationships are given in Table 1.

Using a 5-level bias scheme for 1 : 16 MUX rate allows VOP< 5 V for most LCD liquids. The effect on the display contrast is negligible.

Table 1 Optimum values for V

MUX

RATE

NUMBER

OF BIAS LEVELS

VOP/V

DISCRIMINATION

Von/V

off

1 : 16 5 3.67 1.277 1 : 32 6 5.19 1.196

8.2 Oscillator

The on-chip oscillator provides the clock signal for the display system. No external components are required. Pin OSC must be connected to VDD.

8.3 External clock

If an external clock is to be used, it must be input at pin OSC. The resulting display frame frequency is given by f

frame

=1⁄

2304fosc

. A clock signal must always be present,

otherwise the LCD may be frozen in a DC state.

8.4 Power-on reset

The Power-on reset block initializes the chip after power-on or power failure.

8.5 Registers

The PCF2104x has two 8-bit registers, an instruction register (IR) and a data register (DR). The register select signal (RS) determines which register will be accessed.

The instruction register stores instruction codes such as display clear and cursor shift, and address information for the Display Data RAM (DDRAM) and Character Generator RAM (CGRAM). The instruction register can be written to, but not read from, by the system controller.

The data register temporarily stores data to be read from the DDRAM and CGRAM. When reading, data from the DDRAM or CGRAM (corresponding to the address in the Address Counter) is written to the data register prior to being read by the ‘Read data’ instruction.

8.6 Busy Flag

The Busy Flag indicates the free/busy status of the PCF2104x. Logic 1 indicates that the chip is busy and further instructions will not be accepted. The Busy Flag is output at pin DB7 when RS = logic 0 and R/

W = logic 1. Instructions should only be written after checking that the Busy Flag is at logic 0 or waiting for the required number of clock cycles.

1997 Dec 16 7

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

8.7 Address Counter (AC)

The Address Counter assigns addresses to the DDRAM and CGRAM for reading and writing and is set by the instructions ‘Set CGRAM address’ and ‘Set DDRAM address’. After a read/write operation the Address Counter is automatically incremented or decremented by 1. The Address Counter contents are output to the bus (DB0 to DB6) when RS = logic 0 and R/W = logic 1.

8.8 Display data RAM (DDRAM)

The DDRAM stores up to 80 characters of display data, represented by 8-bit character codes. DDRAM locations not used for storing display data can be used as general purpose RAM. The basic DDRAM-to-display mapping scheme is shown in Fig.2. With no display shift, the characters represented by the codes in the first 12 or 24 RAM locations, starting at address 00 in line 1, are displayed. Subsequent lines display data starting at addresses 20, 40, or 60 Hex. Figures 3 and 4 show the DDRAM-to-display mapping scheme when the display is shifted.

The address range for a 1-line display is 00 to 4F; for a 2-line display from 00 to 27 (line 1) and 40 to 67 (line 2); for a 4-line display from 00 to 13, 20 to 33, 40 to 53 and 60 to 73 for lines 1, 2, 3 and 4 respectively. For 2 and 4-line displays the end address of one line and the start address of the next line are not consecutive. When the display is shifted each line wraps around independently of the others (see Figs 3 and 4).

When data is written to the DDRAM wrap-around occurs from 4F to 00 in 1-line mode and from 27 to 40 and 67 to 00 in 2-line mode; from 13 to 20, 33 to 40, 53 to 60 and 73 to 00 in 4-line mode.

8.9 Character generator ROM (CGROM)

The character generator ROM generates 240 character patterns in 5 × 8 dot format from 8-bit character codes. Figures 5 and 6 show the character sets currently available.

8.10 Character generator RAM (CGRAM)

Up to 16 user-defined characters may be stored in the character generator RAM. The CGROM and CGRAM use a common address space, of which the first column is reserved for the CGRAM (see Fig.5). Figure 8 shows the addressing principle for the CGRAM.

8.11 Cursor control circuit

The cursor control circuit generates the cursor (underline and/or character blink as shown in Fig.9) at the DDRAM address contained in the Address Counter. When the Address Counter contains the CGRAM address the cursor will be inhibited.

8.12 Timing generator

The timing generator produces the various signals required to drive the internal circuitry. Internal chip operation is not disturbed by operations on the data buses.

8.13 LCD row and column drivers

The PCF2104x contains 32 row and 60 column drivers, which connect the appropriate LCD bias voltages in sequence to the display, in accordance with the data to be displayed. The bias voltages and the timing are selected automatically when the number of lines in the display is selected. Figures 10 and 11 show typical waveforms.

In the 1-line mode (1 : 16) the row outputs are driven in pairs: R1/R17, R2/R18 for example. This allows the output pairs to be connected in parallel, thereby providing greater drive capability.

Unused outputs should be left unconnected.

1997 Dec 16 8

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

Fig.2 DDRAM-to-display mapping; no shift (PCF2104x).

handbook, 4 columns

12345 222324

00 01 02 03 04 15 16 17 18 19 4C 4D 4E 4F

non-displayed DDRAM addresses

Display Position (decimal)

DDRAM Address (hex)

1-line display

64 65 66 6740 41 42 43 44 55 56 57 58 59

00 01 02 03 04 15 16 17 18 19

24 25 26 27

non-displayed DDRAM address

DDRAM

(hex)

Address

2-line display

line 1

line 2

MLA792

handbook, 4 columns

123456789101112

non-displayed DDRAM addresses

DDRAM Address (hex)

4 line display

00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13

20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33

40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53

60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73

line 1

line 2

line 3

line 4

MLA793

1997 Dec 16 9

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

Fig.3 DDRAM-to-display mapping; right shift

(PCF2104x).

27 00 01 02 03

67 40 41 42 43

14 15 16

54 55 56

DDRAM Address

(hex)

line 1

line 2

2-line display

1 2 3 4 5 22 23 24

4F 00 01 02 03 14 15 16

Display Position (decimal)

DDRAM Address (hex)

1-line display

MLA802

13 01 02 03 04 05 06 07 08 09 0A

20 21 22 23 24 25 26 27 28 29 2A33

40 41 42 43 44 45 46 47 48 49 4A53

60 61 62 63 64 65 66 67 68 69 6A73

123456789101112

DDRAM Address

(hex)

line 1

line 2

line 3

line 4

4-line display

MLA803

Fig.4 DDRAM-to-display mapping; left shift

(PCF2104x).

1 2 3 4 5 22 23 24

0501 02 03 04

16 17 18

41 42 43 44 45 56 57 58

0501 02 03 04

16 17 18

Display Position (decimal)

DDRAM Address (hex)

DDRAM Address

(hex)

line 1

line 2

1-line display

2-line display

MLA815

01 02 03 04 05 06 07 08 09 0A 0B 0C

21 22 23 24 25 26 27 28 29 2A 2B 2C

41 42 43 44 45 46 47 48 49 4A 4B 4C

61 62 63 64 65 66 67 68 69 6A 6B 6C

123456789101112

DDRAM Address

(hex)

line 1

line 2

line 3

line 4

4-line display

MLA816

1997 Dec 16 10

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

Fig.5 Character set ‘C’ in CGROM; PCF2104C.

handbook, full pagewidth

MLB895

0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111

upper 4 bits

lower 4 bits

xxxx 0000

xxxx 0001

xxxx 0010

xxxx 0011

xxxx 0100

xxxx 0101

xxxx 0110

xxxx 0111

xxxx 1000

xxxx 1001

xxxx 1010

xxxx 1011

xxxx 1100

xxxx 1101

xxxx 1110

xxxx 1111 16

CG RAM 1

1997 Dec 16 11

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

Fig.6 Character set ‘L’ in CGROM; PCF2104L.

handbook, full pagewidth

MGC629

0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111

upper 4 bits

lower 6 bits

xxxx 0000

xxxx 0001

xxxx 0010

xxxx 0011

xxxx 0100

xxxx 0101

xxxx 0110

xxxx 0111

xxxx 1000

xxxx 1001

xxxx 1010

xxxx 1011

xxxx 1100

xxxx 1101

xxxx 1110

xxxx 1111 16

CG RAM 1

1997 Dec 16 12

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

Fig.7 Character set ‘N’ in CGROM; PCF2104N.

handbook, full pagewidth

MGM134

xxxx 1111 16

0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 11110000

upper 4 bits

lower 4 bits

xxxx 0000

xxxx 0001

xxxx 0010

xxxx 0011

xxxx 0100

xxxx 0101

xxxx 0110

xxxx 0111

xxxx 1000

xxxx 1001

xxxx 1010

xxxx 1011

xxxx 1100

xxxx 1101

xxxx 1110 15

CG RAM 1

1997 Dec 16 13

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

Fig.8 Relationship between CGRAM addresses, data and display patterns.

handbook, full pagewidth

MGA800 - 1

76543210 6543210 43210

higher

order

bits

lower order

bits

lower order

bits

higher

order

bits

lower order

bits

higher

order

bits

00000000 0000000 0

001 000 010 000 011 0 100 0 00 101 00 0 110 000 111 00000

000 000 001 0 0 0 010

00 00011 100 101 00 00 110 00 00 111 00000

001

00000001 0001

00000010

00001111 00001111 00001111 00001111

010 0000

100 101 110 1

1 1 1 1

1 1 1 111

character codes

(DDRAM data)

CGRAM address

character patterns

(CGRAM data)

character

pattern

example 1

cursor

position

character

pattern

example 2

Character code bits 0to 3 correspond to CGRAM address bits 3 to 6. CGRAM address bits 0 to 2 designate character pattern line position. The 8th line is the cursor position and display is performed by logical OR with the

cursor. Data in the 8

line will appear in the cursor position. Character pattern column positions correspond to CGRAM data bits 0 to 4; bit 4 being at the left end, as shown in the figure. CGRAM character patterns are selected when character code bits 4 to 7 are all logic 0. CGRAM data = logic 1 corresponds to selection for display. Only bits 0 to 5 of the CGRAM address are set by the ‘Set CGRAM address’ instruction. Bit 6 can be set using the ‘Set DDRAM address’ instruction or

by using the auto-increment feature during CGRAM write. All bits 0 to 6 can be read using the ‘Read Busy Flag and address’ instruction.

1997 Dec 16 14

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

Fig.9 Cursor and blink display examples.

MGA801

cursor

5 x 7 dot character font alternating display

cursor display example blink display example

1997 Dec 16 15

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

Fig.10 Typical LCD waveforms; 1-line mode.

handbook, full pagewidth

MGA802 - 1

V V

LCD

ROW 1

COL 1

state 1 (ON) state 2 (ON)

0.25 V

0 V

state 1

1-line display (1:16)

frame n 1frame n

ROW 9

ROW 2

COL 2

state 2

123 16123 16

V /V

V V

LCD

V /V

V V

LCD

V /V

V V

LCD

V /V

V V

LCD

V /V

0.25 V

0 V

0.25 V

1997 Dec 16 16

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

Fig.11 Typical LCD waveforms; 2-line mode.

handbook, full pagewidth

MGA803 - 1

V V V V

3 4

5 LCD

ROW 1

V V V V

3 4 5 LCD

V V V V

3 4 5 LCD

COL 1

V V V V

3 4 5 LCD

state 1 (ON) state 2 (ON)

0.15 V

0 V

state 1

2-line display (1:32)

frame n 1

frame n

ROW 9

ROW 2

COL 2

V V V V

3 4 5 LCD

0.15 V

0 V

0.15 V

state 2

123 3212 3 32

1997 Dec 16 17

Philips Semiconductors Product speciﬁcation

LCD controller/driver PCF2104x

8.14 Programming of MUX 1 : 16 displays with PCF2104x

The PCF2104x can be used in the following ways:

• 1-line mode to drive a 2-line display

• 2 × 12 characters with MUX rate 1 : 16, resulting in

better contrast. The internal data flow of the chip is optimized for this purpose.

Using the ‘Function set’ instruction, M and N are set to 0, 0 (respectively). Figures 12, 13 and 14 show the DDRAM addresses of the display characters. The second row of each table corresponds to either the right half of a 1-line display or to the second line of a 2-line display. Wrap around of data during display shift or when writing data is non-standard.

Fig.12 DDRAM-to-display mapping; no shift (PCF2104x).

handbook, full pagewidth

01 02

05 06

09 0A

10 11

MLB899

display position DDRAM address

0D 0E

11 12

15 16

14 15

18 19

22 23

display position DDRAM address

Fig.13 DDRAM-to-display mapping; right shift (PCF2104x).

handbook, full pagewidth

00 01

04 05

08 09

10 11

MLB900

display position DDRAM address

0C 0D

10 11

14 15

18 19

22 23

display position DDRAM address

handbook, full pagewidth

02 03

06 07

0A 0B

10 11

MLB901

display position DDRAM address

0E 0F

12 13

16 17

14 15

18 19

22 23

display position DDRAM address

Fig.14 DDRAM-to-display mapping; left shift (PCF2104x).

+ 39 hidden pages