![](/html/9c/9cde/9cde919d6f583d257a2b26ccf8bf701c3353eed9273358c78750626b78658785/bg1.png)
INTEGRATED CIRCUITS
DATA SH EET
PCF1179C
4-digit duplex LCD car clock
Product specification
Supersedes data of September 1993
File under Integrated Circuits, IC16
1997 Apr 16
![](/html/9c/9cde/9cde919d6f583d257a2b26ccf8bf701c3353eed9273358c78750626b78658785/bg2.png)
Philips Semiconductors Product specification
4-digit duplex LCD car clock PCF1179C
FEATURES
• Internal voltage regulator is electrically programmable
for various LCD voltages
• Time calibration is electrically programmable
(no trimming capacitor required)
• LCD voltage adjusts with temperature for good contrast
• 4.19 MHz oscillator
• 12-hour or 24-hour mode
• Operating ambient temperature: −40 to +85 °C
GENERAL DESCRIPTION
The PCF1179C is a single chip, 4.19 MHz CMOS car clock
circuit providing hours, minutes and seconds functions.
It is designed to drive a 4-digit duplex liquid crystal display
(LCD).
Two external single-pole, single-throw switches will
accomplish all time setting functions. Time calibration and
voltage regulator are electrically programmable via an
on-chip EEPROM. The circuit is battery-operated via an
internal voltage regulator and an external resistor.
• 28-lead plastic SMD (SO28)
• 4 Hz set mode.
ORDERING INFORMATION
TYPE
NUMBER
NAME DESCRIPTION VERSION
PCF1179CT SO28 plastic small outline package; 28 leads; body width 7.5 mm
PCF1179CU − uncased chip in tray
(2)
PCF1179CU/10 − chip-on-film frame carrier (FFC)
PACKAGE
(1)
(2)
Notes
1. See Fig.1 and Chapter “Package outline” for pin layout and package details.
2. See Chapter “Chip dimensions and bonding pad locations” for pad layout and package details.
SOT136-1
−
−
1997 Apr 16 2
![](/html/9c/9cde/9cde919d6f583d257a2b26ccf8bf701c3353eed9273358c78750626b78658785/bg3.png)
Philips Semiconductors Product specification
4-digit duplex LCD car clock PCF1179C
PINNING
SYMBOL PIN DESCRIPTION
S1 1 hour adjustment input
DATA 2 EEPROM data input
OSC IN 3 oscillator input
OSC OUT 4 oscillator output
V
SS
5 negative supply voltage
MODE 6 12/24-hour mode select input
V
PP
7 programming voltage input
TS 8 test speed-up mode input
ENABLE 9 enable input (for S1 and S2)
V
DD
10 positive supply voltage
FLASH 11 colon option input
SEL 12 EEPROM select input
S2 13 minute adjustment input
B4/C4 14 segment driver
G4/D4 15 segment driver
F4/E4 16 segment driver
B3/C3 17 segment driver
G3/AD3 18 segment driver
F3/E3 19 segment driver
A4/COL 20 segment driver
B2/C2 21 segment driver
G2/D2 22 segment driver
F2/E2 23 segment driver
B1/C1 24 segment driver
A2/ADEG1 25 segment driver
AM/PM 26 segment driver
BP2 27 backplane 2
BP1 28 backplane 1
OSC IN
OSC OUT
ENABLE
FLASH
Fig.1 Pin configuration, PCF1179CT, (SO28).
S1
DATA
V
SS
MODE
V
PP
TS
V
DD
SEL
S2
B4/C4
1
2
3
4
5
6
7
PCF1179CT
8
9
10
11
12
13
MSB231
28
27
26
25
24
23
22
21
20
19
18
17
16
1514
BP1
BP2
AM/PM
A2/ADEG1
B1/C1
F2/E2
G2/D2
B2/C2
A4/COL
F3/E3
G3/AD3
B3/C3
F4/E4
G4/D4
1997 Apr 16 3
![](/html/9c/9cde/9cde919d6f583d257a2b26ccf8bf701c3353eed9273358c78750626b78658785/bg4.png)
Philips Semiconductors Product specification
4-digit duplex LCD car clock PCF1179C
FUNCTIONAL DESCRIPTION AND TESTING
Outputs
The circuit outputs 1 : 2 multiplexed data (duplex) to the
LCD. Generation of BP1 and BP2 (three-level backplane
signals) and the output signals are shown in Fig.4.
F2
E2
A2
G2
AM
E1
A1
G1
B1
C1
PM
D1
Fig.2 Segment designation of LCD.
D2
The average voltages across the segments are:
B2
C2
1. V
2. V
ON(RMS)
OFF(RMS)
COL
= 0.79 V
= 0.35 VDD.
F3
E3
A3
G3
D3
DD
B3
C3
F4
E4
A4
G4
D4
MLB251
B4
C4
TIME
TIME
PM
(a)
a. 12-hour mode.
(b)
b. 24-hour mode.
MSA994
MSA993
BP1
BP2
SEGMENT1SEGMENT
ON ON
OFF ON
ON OFF
OFF OFF
2
MSB226
V
DD
VDD/2
V
DD
VDD/2
V
DD
V
DD
V
DD
V
DD
0
0
0
0
0
0
15.625 ms
Fig.3 Typical displays.
1997 Apr 16 4
Fig.4 Backplane and output signals.
![](/html/9c/9cde/9cde919d6f583d257a2b26ccf8bf701c3353eed9273358c78750626b78658785/bg5.png)
Philips Semiconductors Product specification
4-digit duplex LCD car clock PCF1179C
LCD voltage (see Fig.5)
The adjustable voltage regulator controls the supply
voltage (see Section “LCD voltage programming”) in
relation to temperature for good contrast, for example
when VDD= 4.5 V at +25 °C, then:
VDD= 3 to 4 V at +85 °C.
VDD= 5 to 6 V at −40 °C.
−8
V
SS
(V)
−6
−4
−2
0
40 0 40 120
(1) Programmed to 4.0 V at 25 °C (value within the specified operating range).
(2) Programmed to 4.5 V at 25 °C (value within the specified operating range).
(3) Programmed to 5.0 V at 25 °C (value within the specified operating range).
(3)
(2)
(1)
Fig.5 Regulated voltage as a function of temperature (typical).
80
MSA995
o
T ( C)
1997 Apr 16 5
![](/html/9c/9cde/9cde919d6f583d257a2b26ccf8bf701c3353eed9273358c78750626b78658785/bg6.png)
Philips Semiconductors Product specification
4-digit duplex LCD car clock PCF1179C
12/24-hour mode
Operation in 12-hour or 24-hour mode is selected by
connecting MODE to VDD or VSS respectively. If MODE is
left open-circuit and a reset occurs, the mode will change
from 12-hour to 24-hour mode or vice versa.
Power-on
After connecting the supply, the start-up mode is:
MODE connected to V
: 12-hour mode, 1:00 AM.
DD
MODE connected to VSS: 24-hour mode, 0:00.
MODE left open-circuit: 24-hour mode, 0:00 or 1:00.
Colon
If FLASH is connected to V
the colon pulses at 1 Hz.
DD
If FLASH is connected to VSS the colon is static.
Time setting
Switch inputs S1 and S2 have a pull-up resistor to facilitate
the use of single-pole, single-throw contacts. A debounce
circuit is incorporated to protect against contact bounce
and parasitic voltages.
Set enable
Inputs S1 and S2 are enabled by connecting ENABLE to
or disabled by connecting to VSS.
V
DD
Set hours
When S1 is connected to V
the hours displayed
SS
advances by one and after one second continues with four
advances per second until S1 is released
(auto-increment). An overflow in the hour counter must not
have an influence on the minute counter.
Set minutes
When S2 is connected to V
the time displayed in
SS
minutes advances by one and after one second continues
with four advances per second until S2 is released
(auto-increment). In addition to minute correction, the
seconds counter is reset to zero. An overflow in the minute
counter must not have an influence on the hour counter.
Segment test/reset
When S1 and S2 are connected to V
, all LCD segments
SS
are switched ON. Releasing switches S1 and S2 resets the
display. No reset occurs when DATA is connected to V
SS
(overlapping S1 and S2).
Test mode
When TS is connected to V
, the device is in normal
DD
operating mode. When connecting TS to VSS all counters
(seconds, minutes and hours) are stopped, allowing quick
testing of the display via S1 and S2 (debounce and
auto-increment times are 64 times faster). TS has a
pull-up resistor but for reasons of safety it should be
connected to VDD.
EEPROM
V
has a pull-up resistor but for reasons of safety it should
PP
be connected to VDD.
LCD voltage programming
To enable LCD voltage programming, SEL is set to
open-circuit and a level of V
− 5 V is applied to VPP (see
DD
Fig.6). The first pulse (tE) applied to the DATA input clears
the EEPROM to give the lowest voltage output. Further
pulses (tL) will increment the output voltage by steps of
typically 150 mV (T
=25°C). For programming,
amb
measure VDD− VSS and apply a store pulse (tW) when the
required value is reached. If the maximum number of steps
(n = 31) is reached and an additional pulse is applied the
voltage will return to the lowest value.
Time calibration
To compensate for the tolerance in the quartz crystal
frequency which has been positively offset (nominal
−6
deviation +60 × 10
by capacitors at the oscillator input
and output, a number (n) of 262144 Hz pulses are
inhibited every second of operation.
1997 Apr 16 6