Philips PCE84C86 Service Manual

INTEGRATED CIRCUITS

DATA SH EET

PCE84C886

Microcontroller for monitor OSD and auto-sync applications

Preliminary speciﬁcation File under Integrated Circuits, IC14

1996 Jan 08

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

CONTENTS

1 FEATURES

1.1 General

1.2 Special

1.3 OSD 2 GENERAL DESCRIPTION 3 ORDERING INFORMATION 4 BLOCK DIAGRAM 5 PINNING INFORMATION

5.1 Pinning

5.2 Pin description 6 RESET

6.1 Reset trip level

6.2 Reset status 7 ANALOG (DC) CONTROL

7.1 6 and 7-bit PWM outputs

7.2 14-bit PWM output

7.3 A typical PWM output application 8 ANALOG-TO-DIGITAL CONVERTER (ADC)

8.1 Conversion algorithm 9 ON SCREEN DISPLAY (OSD)

9.1 Horizontal starting position control

9.2 Vertical starting position control

9.3 On-chip clock generator 10 DISPLAY RAM ORGANIZATION

10.1 Description of display RAM codes

10.2 Default values of OSD after Power-on-reset

10.3 Loading character data into display RAM

10.4 Writing character data into display RAM 11 CHARACTER ROM

11.1 Character ROM address map

11.2 Character ROM organization

11.3 Combination of character font cells

PCE84C886

12 OSD CONTROL REGISTERS

12.1 Derivative Register 22

12.2 Derivative Register 23

12.3 Derivative Register 33

12.4 Derivative Register 34

12.5 Derivative Register 35

12.6 Derivative Register 36

12.7 Derivative Register 37 13 TO FORMAT THE OSD

13.1 Number of characters per row

13.2 Number of rows per frame

13.3 Character size selection for different display resolutions

14 8-BIT COUNTER (T3) 15 I2C-BUS INTERFACE 16 OUTPUT PORTS

16.1 Mask options

17 DERIVATIVE REGISTERS 18 LIMITING VALUES 19 DC CHARACTERISTICS 20 AC CHARACTERISTICS 21 DEVELOPMENT SUPPORT 22 PACKAGE OUTLINE 23 SOLDERING

23.1 Introduction

23.2 Soldering by dipping or by wave

23.3 Repairing soldered joints

24 DEFINITIONS 25 LIFE SUPPORT APPLICATIONS 26 PURCHASE OF PHILIPS I2C COMPONENTS

1996 Jan 08 2

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

1 FEATURES

1.1 General

• CMOS 8-bit CPU (enhanced 8048 CPU) with 8 kbytes system ROM and 192 bytes system RAM

• One 8-bit timer/event counter (T1) and one 8-bit counter triggered by external input (T3)

• Four single level vectored interrupt sources: external (INTN), counter/timer, I

• 2 directly testable inputs T0 and T1

• On-chip oscillator clock frequency: 1 to 10 MHz

• On-chip Power-on-reset with low power detector

• Twelve quasi-bidirectional I/O lines, configuration of

each I/O line individually selected by mask option

• Idle and Stop modes for reduced power consumption

• Operating temperature: −25 to +85 °C

• Operating voltage: 4.5 to 5.5 V

• Package: SDIP42.

1.2 Special

• Master-slave I

• Four 6-bit Pulse Width Modulated outputs

(PWM4 to PWM7)

• Four 7-bit Pulse Width Modulated outputs (PWM0 to PWM3)

• One 14-bit Pulse Width Modulated output (PWM8)

• Three 4-bit ADC channels

• 16 derivative I/O ports.

1.3 OSD

• Maximum dot frequency (f

• Display RAM: 64 × 10 bits

• Display character fonts: 62 + 2 special reserved codes

• Character matrix: 12 × 18 (no spacing between

characters)

• 4 character sizes: 1H/1V, 1H/2V, 1H/3V and 1H/4V

• 64 Horizontal starting positions (4 dots for each step)

• 64 Vertical starting positions (4 scan lines for each step)

C-bus interface

C-bus and VSYNCN

): 14 MHz

OSD

PCE84C886

• Spacing between character rows: 0, 4, 8 and 12 scan lines

• Foreground colours: 8 on a character-by-character basis

• Background colours: 8 on a word-by-word basis

• Background/shadowing modes: 4 modes available, No

background, North shadowing, Box shadowing and Frame shadowing (raster blanking) on a frame basis

• On-chip Phase-Locked Loop (PLL) oscillator (auto-sync with HSYNCN) with programmable oscillator for On Screen Display (OSD) function

• Character blinking frequency: programmable using f

divisors of 16, 32, 64 and 128; on a frame basis

Vsync

• Character blinking ratios: 1 : 1, 1 : 3 and 3 : 1

• Programmable active level polarities of VSYNCN,

HSYNCN, R, G, B and FB

• Flexible display format by using Carriage Return Code

• Auto display RAM address (DCRAR) incremented after

write operation to the Character Data Register (DCRCR)

• VSYNCN generates an interrupt (enabled by software) when VIEN is active.

2 GENERAL DESCRIPTION

The PCE84C886 is a member of the 84CXXX CMOS microcontroller family. It is suitable for use in 14", 15" and 17" auto-sync monitors for OSD and auto-sync applications. The device uses the PCE84CXX processor core and has 8 kbytes of ROM and 192 bytes of RAM. I/O requirements are adequately catered for with 12 general purpose bidirectional I/O lines plus 16 function combined I/O lines. 9 PWM analog outputs are provided specifically for analog control purposes and also three 4-bit ADCs. The device has an 8-bit counter, suitable for use in pulse counting applications; an 8-bit timer/counter with programmable clock and an on-chip programmable PLL oscillator that generates the OSD clock. In addition to all these features a master-slave I testable lines and an enhanced OSD facility for flexible screen format (64 character types) are also provided.

The block diagram of the PCE84C886 is shown in Fig.1.

C-bus interface, 2 directly

3 ORDERING INFORMATION

TYPE NUMBER

NAME DESCRIPTION VERSION

PCE84C886 SDIP42 plastic shrink dual in-line package; 42 leads (600 mil) SOT270-1

1996 Jan 08 3

PACKAGE

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

4 BLOCK DIAGRAM

handbook, full pagewidth

INTN / T0 T3

CPU

XTAL1 (IN)

XTAL2 (OUT)

8-BIT

TIMER /

EVENT

COUNTER

8-BIT

COUNTER

ROM

8 kbytes

RAM

192 bytes

VOW0

VOW2CVSYNCN

VOW1

(3) (3)

ON SCREEN DISPLAY

PCE84C886

HSYNCN

8-bit internal bus

RESET

PARALLEL

I / O

TEST / EMU

(1) Alternative function of DP0. (2) Alternative function of DP1. (3) Alternative function of DP2.

PORTS

PCF84CXX core excluding ROM / RAM

8-BIT

I / O

PORTS

48 4

DP0 DP1 DP2

Fig.1 Block diagram.

4 x 6-BIT PWM 4 x 7-BIT PWM

(1) (2) (2) (3)

PWM0

PWM7

14-BIT

PWM

PWM8 ADC0

3 x 4-BIT

ADC

ADC2

I C-BUS

INTERFACE

SDA SCL

MLC067

(3)

1996 Jan 08 4

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

5 PINNING INFORMATION

5.1 Pinning

handbook, halfpage

VOW1/DP22 VOW0/DP23

VSYNCN HSYNCN

DP13/PWM8

VOW2

P10 P11

PCE84C886

1 2 3 4 5 6 7 8 9

42 41 40 39 38 37 36 35 34

C DP20/SDA DP21/SCL DP10/ADC0 DP11/ADC1 DP12/ADC2 INTN/T0 T1

P12

PCE84C886

P14

P00

P01

P02

P03

P04

P05

P06

P07

MLC068

Fig.2 Pin configuration.

RESET

XTAL2 (OUT)

XTAL1 (IN)

TEST/EMU

DP00/PWM0

DP01/PWM1

DP02/PWM2

DP03/PWM3

DP04/PWM4

DP05/PWM5

DP06/PWM6

DP07/PWM7

1996 Jan 08 5

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD

PCE84C886

and auto-sync applications

5.2 Pin description Table 1 SDIP42 package

SYMBOL PIN DESCRIPTION

FB 1 Video Fast Blanking output. VOW2 2 Video character output VOW2. VOW1/DP22 3 Video character output VOW1 or Derivative Port line DP22. VOW0/DP23 4 Video character output VOW0 or Derivative Port line DP23. VSYNCN 5 Vertical synchronization signal input. HSYNCN 6 Horizontal synchronization signal input. P10 7 Port line 10 or emulation input P11 8 Port line 11 or emulation input DP13/PWM8 9 Derivative I/O port or PWM8 output. P12 10 Port line 12 or emulation input DXALE. T3 11 Secondary 8-bit counter input (Schmitt trigger). P14 12 Port line 14 or emulation output DXINT. P00 to P07 13 to 20 General I/O port lines. V

DP00/PWM0 to DP07/PWM7 29, 28, 27, 26

TEST/EMU 30 Control input for testing and emulation mode, normally LOW. XTAL1 (IN) 31 Oscillator input pin for system clock. XTAL2 (OUT) 32 Oscillator output pin for system clock. RESET 33 Reset input; active LOW input initializes device. T1 34 Direct testable pin or event counter input. INTN/T0 35 External interrupt or direct testable pin. DP10/ADC0 38 Derivative I/O port or ADC Channel 0 input. DP11/ADC1 37 Derivative I/O port or ADC Channel 1 input. DP12/ADC2 36 Derivative I/O port or ADC Channel 2 input. DP21/SCL 39 Derivative port line or I DP20/SDA 40 Derivative port line or I C 41 External capacitor input for on-chip oscillator. V

21 Ground.

Derivative I/O ports or PWM outputs.

25, 24, 23, 22

42 Power supply.

C-bus clock input.

C-bus data input.

DXWR.

DXRD.

1996 Jan 08 6

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

6 RESET

The RESET pin may be used as an active LOW input to initialize the microcontroller to a defined state.

An active reset can be generated by driving theRESET pin from an external logic device. Such an active reset pulse should not fall off before VDD has reached its f

-dependent minimum operating voltage.

xtal

A Power-on-reset can be generated using an external RC circuit. To avoid overload of the internal diode, an external diode should be added in parallel if C RC circuit is shown in Fig.3.

6.1 Reset trip level

The RESET trip voltage level is masked to 1.3 V in the PCE84C886.

If any input (for example Hsync) goes HIGH before V applied, latch-up may occur and in this situation the PCE84C886 cannot be reset. The cause and effect of latch-up is shown in Fig.4.

6.2 Reset status

• Derivative Registers reset status; see Table 38 for details

• Program Counter 00H

• Memory Bank 0

• Register Bank 0

• Stack Pointer 00H

• All interrupts disabled

• Timer/event counter 1 stopped and cleared

• Timer pre-scaler modulo-32 (PS = 0)

• Timer flag cleared

• Serial I/O interface disabled (ESO = 0) and in slave

receiver mode

• Idle and Stop mode cleared.

RESET

≥ 2.2 µF. The

PCE84C886

handbook, halfpage

RESET

( 100 kΩ)

RESET

Fig.3 External components for RESET pin.

handbook, halfpage

HSYNCN

RESET

Hsync

RESET

Fig.4 The influence of an active HIGH signal being

applied before Power-on-reset.

internal reset

PCA84C8XX

internal V

PCE84C886

internal reset

MLC259

MLC260

1996 Jan 08 7

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

7 ANALOG (DC) CONTROL

The PCE84C886 has nine Pulse Width Modulated (PWM) outputs for analog control purposes e.g. brightness, contrast, H-shift, V-shift, H-width, V-size, E-W, R (or G or B) gain control etc. Each PWM output generates a pulse pattern with a programmable duty cycle.

The nine PWM outputs are specified below:

• 4 PWM outputs with 6-bit resolution (PWM4 to PWM7)

• 4 PWM outputs with 7-bit resolution (PWM0 to PWM3)

• 1 PWM output with 14-bit resolution (PWM8).

The 6 and 7-bit PWM outputs are described in Section 7.1; the 14-bit PWM output is described in Section 7.2 and a typical PWM output application is described in Section 7.3.

7.1 6 and 7-bit PWM outputs

PWM outputs PWM0 to PWM7 share the same pins as Derivative Port lines DP00 to DP07 respectively. Selection of the pin function as either a PWM output or a Derivative Port line is achieved using the appropriate PWMnE bit in Register 21 (see Table 38).

PCE84C886

The duty cycle of outputs PWM0 to PWM7 is dependent on the programmable contents of the data latches (Registers 10 to 17 respectively). As the clock frequency of each PWM circuit is pulse generated can be calculated as shown below.

Pulse width

3 PWMn()×

----------------------------------

Where (PWMn) is the decimal value held in the data latch. The maximum repetition frequency (f

7-bit PWM outputs is shown below.

For the 6-bit PWM outputs:

For the 7-bit PWM outputs:

The block diagram for the 6 and 7-bit PWM outputs is shown in Fig.5.

⁄3× f

xtal

, the pulse width of the

xtal

) of the 6 and

PWM

xtal

--------- 192

xtal

--------- 384

The polarity of the PWM outputs is programmable and is selected by the P7LVL and P6LVL bits in Register 23 (see Section 12.2).

handbook, full pagewidth

xtal

6 or 7-BIT PWM DATA LATCH

6 or 7-BIT DAC PWM

CONTROLLER

internal data bus

P6LVL/P7LVL

DP0x data

I/O

PWMnE

DP0x/PWMx

MLC069

Fig.5 Block diagram for 6 and 7-bit PWMs.

1996 Jan 08 8

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

handbook, full pagewidth

xtal

64

or

128

63

or

127

1 2 3 m m + 1 m + 2

decimal value PWM data latch

PCE84C886

64

or

128

MLC261

Fig.6 Typical non-inverted output pulse patterns for 6 or 7-bit PWM outputs.

1996 Jan 08 9

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

7.2 14-bit PWM output

PWM8 shares the same pin as Derivative Port line DP13. Selection of the pin function as either a PWM output or as a Derivative Port line is achieved using the PWM8E bit in Register 22 (see Section 12.1).

The Block diagram for the 14-bit PWM output is shown in Fig.7 and comprises:

• Two 7-bit latches: PWM8L (Register 18) and PWM8H (Register 19)

• 14-bit data latch (PWMREG)

• 14-bit counter

• Coarse pulse controller

• Fine pulse controller

• Mixer.

Data is loaded into the 14-bit data latch (PWMREG) from the two 7-bit data latches (PWM8H and PWM8L) when either of these data latches is written to. The upper seven bits of PWMREG are used by the coarse pulse controller and determine the coarse pulse width; the lower seven bits are used by the fine pulse controller and determine in which subperiods fine pulses will be added. The outputs OUT1 and OUT2 of the coarse and fine pulse controllers are ‘ORED’ in the mixer to give the PWM8 output. The polarity of the PWM8 output is programmable and is selected by the P8LVL bit in Register 23, this is described in Section 12.2.

As the 14-bit counter is clocked by f times of the coarse and fine pulse controllers may be calculated as shown below.

Coarse controller repetition time:

Fine controller repetition time:

Figure 8 shows typical PWM8 outputs, with coarse adjustment only, for different values held in PWM8H. Figure 9 shows typical PWM8 outputs, with coarse and fine adjustment, after the coarse and fine pulse controller outputs have been ‘ORED’ by the mixer.

/3, the repetition

xtal

sub

49152

----------------

xtal

384

--------- f

xtal

PCE84C886

7.2.1 C An active HIGH pulse is generated in every subperiod; the

pulse width being determined by the contents of PWM8H. The coarse output (OUT1) is LOW at the start of each subperiod and will remain LOW until the time

⁄ PWM8H 1+()×[] then go HIGH and remain HIGH until the start of the next subperiod. The coarse pulse width may be calculated as shown below.

Pulse duration 127 PWM8H–()

7.2.2 F Fine adjustment is achieved by generating an additional

pulse in specific subperiods. The pulse is added at the start of the selected subperiod and has a pulse width of 3/f

xtal

subperiods a fine pulse will be added. It is the logic 0 state of the value held in PWM8L that actually selects the subperiods. When more than one bit is a logic 0 then the subperiods selected will be a combination of those subperiods specified in Table 2. For example, if PWM8L = 111 1010 then this is a combination of:

• PWM8L = 111 1110: subperiod 64 and

• PWM8L = 111 1011: subperiods 16, 48, 80 and 112.

Pulses will be added in subperiods 16, 48, 64, 80 and 112. This example is illustrated in Fig.10.

When PWM8L holds 111 1111 fine adjustment is inhibited and the PWM8 output is determined only by the contents of PWM8H.

Table 2 Additional pulse distribution

PWM8L ADDITIONAL PULSE IN SUBPERIOD

111 1110 64 111 1101 32 and 96 111 1011 16, 48, 80 and 112 111 0111 8, 24, 40, 56, 72, 88, 104 and 120 110 1111 4, 12, 20, 28, 36, 44, 52...116 and 124 101 1111 2, 6, 10, 14, 18, 22, 26, 30...122 and 126 011 1111 1, 3, 5, 7, 9, 11, 13, 15, 17...125 and 127

OARSE ADJUSTMENT

xtal

INE ADJUSTMENT

has elapsed. The output will

×=

-------f

xtal

. The contents of PWM8L determine in which

1996 Jan 08 10

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

handbook, full pagewidth

‘MOVE instruction’

PWM8H

DATA LOAD

TIMING PULSE

LOAD

Internal data bus

7 7

PWMREG

PWM8L

PCE84C886

‘MOV instruction’

polarity control bit

P8LVL

7 7

COARSE 7-BIT

PWM

MIXER

Q14 to 8 Q7 to 1

14-BIT COUNTER

FINE PULSE

GENERATOR

OUT2OUT1

MLC071

PWM8 output

f = f

tdac xtal

Fig.7 14-bit PWM Block diagram.

1996 Jan 08 11

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

handbook, full pagewidth

xtal

127 0 1 2 m m + 1 m + 2

127

decimal value PWM8H data latch

PCE84C886

127 0 1

MLC263

xtal

handbook, full pagewidth

127 0 1 2 m m + 1 m + 2

127

Fig.8 Non-inverted PWM8 output patterns - Coarse adjustment only.

127 0 1

MLC262

decimal value PWM8H data latch

Fig.9 Non-inverted PWM8 output patterns - Coarse and Fine adjustment.

1996 Jan 08 12

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

handbook, full pagewidth

111 1110

111 1011

111 1010

PWM8L

sub0

sub16

sub32

sub48

sub64

PCE84C886

sub80

sub96

sub112

sub127

MLC755

Fig.10 Fine adjustment output (OUT2).

7.3 A typical PWM output application

A typical PWM application is shown in Fig.11. The buffer is used to reduce jitter on the OSD. R1 and C1 form the integration network the time constant of which should be equal to or greater than 5 times the repetition period of the PWM output pattern. In order to smooth a changing PWM output a high value of C1 should be chosen. The value of C1 will normally be in the range 1 to 10 µF. The potential divider chain formed by R2 and R3 is used only when the output voltage is to be offset. The output voltages for this application are calculated using Equations (1) and (2).

min

----------------------------------------------------

max

R1 R3×

--------------------- R1 R3+

-------------------------------------------------------------------

R1 R2×

---------------------R1 R2+

supply voltage×

R1 R3×

---------------------R1 R3+

The loop from the PWM pin through R1 and C1 to V

(1)

(2)

will

R3 supply voltage×

radiate high frequency energy pulses. In order to limit the effect of this unwanted radiation source, the loop should be kept short and a high value of R1 selected. The value of R1 will normally be in the range 3.3 to 100 kΩ. It is good practice to avoid sharing VSS (pin 21) with the return leads of other sensitive signals.

handbook, halfpage

PCE84C886

PWMn

MLC070

C1 R3

Fig.11 Typical PWM output circuit.

supply



voltage

analog output

1996 Jan 08 13

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

8 ANALOG-TO-DIGITAL CONVERTER (ADC)

The 3 channel ADC comprises a 4-bit Digital-to-Analog Converter (DAC); a comparator; an analog channel selector and control circuitry. As the digital input to the 4-bit DAC is loaded by software (a subroutine in the program), it is known as a software ADC. The block diagram is shown in Fig.12.

The ADC inputs ADC0 to ADC2 share the same pins as Derivative Port lines DP10 to DP12 respectively. Selection of the pin function as either an ADC input or as a Derivative Port line is achieved using bits ADCE0 to ADCE2 in Register 22. When ADCEn = 1, the ADC function is enabled (see Section 12.1).

The 4-bit DAC analog output voltage (V by the decimal value of the data held in bits DAC0 to DAC3 of Register 20. V and Table 3 lists the V

is calculated as shown in Equation (3)

ref

values assuming VDD=5V.

ref

---------16

DAC value 1+()×=

When the analog input voltage is higher than V COMP bit in Register 20 will be HIGH.

Table 3 Selection of V

ref

DAC3 DAC2 DAC1 DAC0 V

00000.3125

00010.6250

00100.9375

00111.2500

01001.5625

01011.8750

01102.1875

01112.5000

10002.8125

10013.1250

10103.4375

10113.7500

11004.0625

11014.3750

11104.6875

11115.0000

) is determined

ref

, the

ref

(V)

ref

(3)

PCE84C886

The channel selector, consisting of three analog switches, is controlled by bits ADCS1 and ADCS0 in Register 20 as highlighted in Table 4.

Table 4 Selection of ADC channel

ADCS1 ADCS0 CHANNEL SELECTED

0 0 ADC0 0 1 ADC1 1 0 ADC2 1 1 reserved

8.1 Conversion algorithm

There are many algorithms available to achieve the ADC conversion. The algorithm described below and shown in Fig.13 uses an iteration process.

1. Select ADCn channel for conversion. Channel selection is achieved using bits ADCS1 and ADCS0 in Register 20.

2. Set the digital input to the DAC to 1000. The digital input to the DAC is selected using bits DAC3 to DAC0 in Register 20.

3. Determine the result of the compare operation. This is achieved by reading the COMP bit in Register 20 using the instruction MOV A, D20. If COMP = 1; the analog input voltage is higher than the reference voltage (V lower than the reference voltage (V

4. If COMP = 1; then the analog input voltage is higher than the reference voltage (V digital input to the DAC needs to be increased. Set the input to the DAC to 1100.

5. If COMP = 0; then the analog input voltage is lower than the reference voltage (V digital input to the DAC needs to be decreased. Set the input to the DAC to 0100.

6. Determine the result of the compare operation by reading the COMP bit in Register 20.

). If COMP = 0; the analog input voltage is

ref

) and therefore the

ref

) and therefore the

ref

1996 Jan 08 14

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

7. For the DAC = 1100 case If COMP = 1; then the analog input voltage is still

greater than V DAC needs to be increased again. Set the input to the DAC to 1110.

If COMP = 0; then the analog input voltage is now less than V

and therefore the digital input to the DAC

ref

needs to be decreased. Set the input to the DAC to 1010

8. For the DAC = 0100 case If COMP = 1; then the analog input voltage is now

greater than V DAC needs to be increased. Set the input to the DAC to 0110.

If COMP = 0; then the analog input voltage is still lower than V

and therefore the digital input to the DAC

ref

needs to be decreased again. Set the input to the DAC to 0010.

and therefore the digital input to the

ref

and therefore the digital input to the

ref

PCE84C886

9. The operations detailed in 6, 7 and 8 above are repeated and each time the digital input to the DAC is changed accordingly; as dictated by the state of the COMP bit. The complete process is shown in Fig.13. Each time the DAC input is changed the number of values which the analog input can take is reduced by half. In this manner the actual analog value is honed into. The value of the analog input (VA) is determined using Equation (4):

As the conversion time of each compare operation is greater than 6 µs but less than 9 µs; a NOP instruction is recommended to be used in between the instructions that change the value of V the COMP bit.

----------

DAC value 1+()×=

; select the ADC channel and read

ref

(4)

handbook, full pagewidth

DP10/ADC0

DP11/ADC1

DP12/ADC2

Channel selection

ADCE0 ADCE1 ADCE2

ADC

CHANNEL

SELECTOR

ADCS1 ADCS0

ADC enable selection

Fig.12 Block diagram of 3 channel ADC.

ENABLE

SELECTOR

ref

DERIVATIVE PORT

−

DAC3

SELECTOR

EN1 EN2EN0

COMPARATOR

4-BIT DAC

DAC2 DAC1 DAC0

DAC value selection

Internal bus

COMP bit

‘MOV A, D20’

instruction

to read COMP bit

MLC072

1996 Jan 08 15

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

Value = 0100

COMP = 1

Value = 0010

COMP = 1

Value = 0001

Value = 0011

Value = 0101

PCE84C886

0000

MLC073

COMP = 1

00010011

0010

COMP = 1

0101 0100

Value = 1000

COMP = 1

Value = 1100

COMP = 1

Value =0110

Value = 1010

Value = 1110

COMP = 1

Value = 0111

Value = 1001

Value = 1011

Value = 1101

COMP = 1

0111 0110

COMP = 1

1001 10001011

1010

COMP = 1

1101 1100

handbook, full pagewidth

Fig.13 Example of converting algorithm for software ADC.

1996 Jan 08 16

Value = 1111

COMP = 1

1111 1110

Philips Semiconductors Preliminary speciﬁcation

Microcontroller for monitor OSD and auto-sync applications

9 ON SCREEN DISPLAY (OSD)

The OSD feature of the PCE84C886 enables the user to display information on the monitor screen. Display information can be created using 62 customer designed characters, a space character and a carriage return code. The OSD block diagram is shown in Fig.14.

9.1 Horizontal starting position control

The horizontal starting position counter is incremented every OSD clock after Hsync becomes inactive and is reset when Hsync becomes active. The horizontal starting position of the display row is determined by the contents of Register 36; 1 of 64 positions may be selected as explained in Section 12.6.

The polarity of the active state of the HSYNCN input is programmable and is determined by the Hp bit in Register 34; see Section 12.4. The active HIGH and active LOW states as selected by the Hp bit are shown in Fig.15.

9.2 Vertical starting position control

The vertical starting position counter is incremented every Hsync cycle and is reset when Vsync becomes active. The vertical starting position of the display row is determined by the contents of Register 35; 1 of 64 positions may be selected as explained in Section 12.5.

The vertical starting position of the display is dependent upon the number of scan lines per frame. To achieve the same starting position with different display resolutions, only the contents of Register 35 need to be changed, the contents of Register 36 remain the same. The lowest vertical starting position that can be selected, is located on the 256th scan-line. However, lower positions may be achieved using the Carriage Return Code.

PCE84C886

9.3 On-chip clock generator

The on-chip oscillator generates an OSD clock that is auto-sync with Hsync. The frequency of the OSD clock is programmable and is determined by the contents of Register 25 which forms the 7-bit counter.

The OSD clock frequency is calculated as follows:

OSDfHsync

Where (Register 25) denotes the decimal value held in Register 25.

The block diagram of the OSD clock is shown in Fig.16. The internal reference frequency is connected to Hsync, and if the frequency of Hsync changes, the output frequency (f character width is not effected by changes in the frequency of Hsync. The internal Hsync signal is designed active HIGH, consequently f edge of this signal.

The OSD clock is enabled/disabled by the state of the EN bit in Register 34; see Section 12.4. When the OSD clock is disabled the oscillator remains active, therefore the transient time from the OSD clock start-up to locking into the external Hsync signal is reduced. As the on-chip oscillator is always active after power-on, when the OSD clock is enabled no large currents flow (as in the case of RC or LC oscillators) and therefore radiated noise is dramatically reduced.

2 Register 25()××=

) will be changed linearly. Therefore, the

OSD

is synchronized with the falling

PLL

When the selected horizontal and vertical starting positions are reached on screen; the OSD is enabled. The character selected in display RAM is then displayed.

The polarity of the active state of the VSYNCN input is programmable and is determined by the Vp bit in Register 34; see Section 12.4. The active HIGH and active LOW states as selected by the Vp bit are shown in Fig.15.

1996 Jan 08 17

+ 39 hidden pages

Philips PCE84C86 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual