Philips PCA5007H-000-F2, PCA5007H-F1 Datasheet

DATA SH EET

Product speciﬁcation File under Integrated Circuits, IC17

1998 Oct 07

INTEGRATED CIRCUITS

PCA5007

Pager baseband controller

1998 Oct 07 2

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

CONTENTS

1 FEATURES 2 ORDERING INFORMATION 3 GENERAL DESCRIPTION 4 BLOCK DIAGRAM 5 PINNING 6 FUNCTIONAL DESCRIPTION

6.1 General

6.2 CPU timing

6.3 Overview on the different clocks used within the PCA5007

6.4 Memory organization

6.5 Addressing

6.6 I/O facilities

6.7 Timer/event counters

6.8 I2C-bus serial I/O

6.9 Serial interface SIO0: UART

6.10 76.8 kHz oscillator

6.11 Clock correction

6.12 6 MHz oscillator

6.13 Real-time clock

6.14 Wake-up counter

6.15 Tone generator

6.16 Watchdog timer

6.17 2 or 4-FSK demodulator, filter and clock recovery circuit

6.18 AFC-DAC

6.19 Interrupt system

6.20 Idle and power-down operation

6.21 Reset

6.22 DC/DC converter

7 INSTRUCTION SET

7.1 Instruction Map

8 LIMITING VALUES 9 EXTERNAL COMPONENTS 10 DC CHARACTERISTICS 11 AC CHARACTERISTICS 12 CHARACTERISTIC CURVES 13 TEST AND APPLICATION INFORMATION

14 APPENDIX 1: SPECIAL MODES OF THE

PCA5007

14.1 Overview

14.2 OTP parallel programming mode

14.3 Test modes 15 APPENDIX 2: THE PARALLEL

PROGRAMMING MODE

15.1 Introduction

15.2 General description

15.3 Entering the parallel programming mode

15.4 Address space

15.5 Single byte programming

15.6 Multiple byte programming

15.7 High voltage timing

15.8 OTP test modes

15.9 Signature bytes

15.10 Security 16 APPENDIX 3: OS SHEET 17 APPENDIX 4: BONDING PAD LOCATIONS 18 PACKAGE OUTLINE 19 SOLDERING

19.1 Introduction

19.2 Reflow soldering

19.3 Wave soldering

19.4 Repairing soldered joints 20 DEFINITIONS 21 LIFE SUPPORT APPLICATIONS 22 PURCHASE OF PHILIPS I2C COMPONENTS

1998 Oct 07 3

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

1 FEATURES

• Operating temperature from: −10 to +55 °C

• Supply voltage range with on-chip DC/DC converter:

0.9 to 1.6 V

• Low operating and standby current consumption

• On-chip DC/DC converter generates the supply voltage

for the PCA5007 and external circuitry from a single cell battery

• Battery low detector

• Low electromagnetic noise emission

• Full static asynchronous 80C51 CPU (8-bit CPU)

• Recovery from lowest power standby Idle mode to full

speed operation within microseconds

• 20 kbytes of One-Time Programmable (OTP) memory

and 1-kbyte of RAM on-chip

• 27 general purpose I/O port lines (4 ports with interrupt

possibility)

• 15 different interrupt sources with selectable priority

• 2 standard timer/event counters T0 and T1

• I

C-bus serial port (single 100 kHz master transmitter

and receiver)

• Subset of standard UART serial port (8 and 9-bit

transmission at 4800/9600 bits/s)

• 76.8 kHz crystal oscillator reference with digital clock

correction for real time and paging protocol

• Real-Time Clock (RTC)

• Receiver and synthesizer control

– Receiver control by software through general

purpose I/Os

– Synthesizer control by software through general

purpose I/Os – 6-bit DAC for AFC to the receiver local oscillator – Dedicated protocol timer.

• Decoding of paging data – POCSAG or APOC phase 1, advanced high speed

paging protocols are also supported

– Supported data rates: 1200, 1600, 2400 and 3200

symbols/s using a 76.8 kHz crystal oscillator

– Demodulation of Zero-IF I andQ4or2level FSK

input or direct data input

– Noise filtering of data input and symbol clock

reconstruction

– De-interleaving, error checking and correction, sync

word detection address recognition, buffering and more is done in software

– All user functions (keypad interface, alerter control,

display, etc.) are implemented in software.

• Musical tone generator for beeper, controlled by the microcontroller

• Watchdog timer

• 48-pin LQFP package.

2 ORDERING INFORMATION

Note

1. Please refer to the Order Entry Form (OEF) for this device for the full type number to use when ordering. This type number will also specify the required OTP code.

TYPE

NUMBER

(1)

PRODUCT TYPE

PACKAGE

NAME DESCRIPTION VERSION

PCA5007H/XXX pre-programmed OTP LQFP48 plastic low proﬁle quad ﬂat package; 48 leads;

body 7 × 7 × 1.4 mm

SOT313-2

1998 Oct 07 4

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

3 GENERAL DESCRIPTION

The PCA5007 pager baseband controller is manufactured in an advanced CMOS/OTP technology.

The PCA5007 is an 8-bit microcontroller especially suited for pagers. For this purpose, features such as a 4 or 2 level FSK demodulator, filter, clock recovery, protocol timer, DC/DC converter optimized for small paging systems and RTC are integrated on-chip.

The device is optimized for low power consumption. The PCA5007 has several software selectable modes for power reduction: Idle and power-down mode of the microcontroller, and standby and off mode of the DC/DC converter.

The instruction set of the PCA5007 is based on that of the 80C51. The PCA5007 also functions as an arithmetic processor having facilities for both binary and BCD arithmetic plus bit-handling capabilities. The instruction set consists of over 100 instructions: 49 one-byte, 46 two-byte, and 16 three-byte.

This data sheet details the properties of the PCA5007. For details of the I

C-bus functions see

“The I2C-bus and

how to use it”

. For details on the basic 80C51 properties

and features see

“Data Handbook IC20”

1998 Oct 07 5

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in

_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in

white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...

4 BLOCK DIAGRAM

ndbook, full pagewidth

MGR107

PORT

CONTROL

XTL2 XTL1

P3 (T0, T1, INT0, INT1)

P1 (SDA, SCL, RXD, TXD)

OTP/ROM

TIMER 0

TIMER 1

RAM

PROCESSOR

80C51

INTERRUPT

CONTROL

UART SIO

SYMBOL SAMPLING

CLOCK RECOVERY

DIGITAL

FILTER

ZERO-IF

4L DEMODULATOR

I2C SIO

CLOCK

CORRECTION

various clocks

CLOCK

GENERATOR

RTC

ALE, PSEN, EA TCLK

WAKE-UP

MODE AND

TEST CONTROL

POWER

CONTROLLER

TONE

GENERATOR

6 MHz

OSCILLATOR

WATCHDOG

DAC

I(D1), Q(D0)

AFCOUT

VIND

DD(DC)

SS(DC)

BAT

supplied by V

BAT

RESETIN

RESOUT

76.8 kHz

OSCILLATOR

DC/DC

CONVERTER

Fig.1 Block diagram.

1998 Oct 07 6

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

5 PINNING

SYMBOL PIN TYPE DESCRIPTION

P3.4 and P3.5 1 and 2 I/O Port 3: P3.4 and P3.5 are conﬁgured as push-pull output only (option 3R; see

Section 6.6). Using the software input commands or the secondary port function is possible by driving the port 3 output lines accordingly:

P3.4 secondary function: T0 (counter input for T0)

P3.5 secondary function: T1 (counter input for T1) AT 3 O Beeper high volume control output. Used to drive external bipolar transistor. P2.0 to P2.7 4 to 11 I/O Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups (option 1S;

see Section 6.6.3). As inputs, port 2 pins that are externally pulled LOW will

source current because of the internal pull-ups. (see Chapter “DC

characteristics”: I

). Port 2 emits the high-order address byte during fetches from external program memory. In this application, it uses strong internal pull-ups when emitting logic 1s. Port 2 is also used to control the parallel programming mode of the on-chip OTP.

P0.0 to P0.4 12 to 16 I/O Port 0: Port 0 is a bidirectional I/O port with internal pull-ups (option 1S; see

Section 6.6.3). Port 0 pins that have logic 1s written to them are pulled HIGH by the internal pull-ups and can be used as inputs. Port 0 is also the multiplexed low-order address and data bus during access to external program and data memory. In this application, it uses strong internal pull-ups when emitting 1s. Port 0 also outputs the code bytes during OTP programming veriﬁcation.

DDA

17 S supply voltage for the analog parts of the PCA5007 and the

receiver/synthesizer control signals (Port 0 pins)

AFCOUT 18 O Buffered analog output of DAC for automatic receiver frequency control.

A voltage proportional to the offset of the receiver frequency can be generated. Can be enabled/disabled by software.

I(D1) 19 I input from receiver: may be demodulated NRZ signal or Zero-IF. In phase

limited signal

Q(D0) 20 I input from receiver: may be demodulated NRZ signal or Zero-IF, Quadrature

limited signal.

SSA

21 S ground signal reference (for the analog parts) (connected to substrate)

P0.5 to P0.7 22 to 24 I/O Port 0: Port 0 is a bidirectional I/O port with internal pull-ups (option 1R,1R and

1S; see Section 6.6.3). Port 0 pins that have logic 1s written to them are pulled HIGH by the internal pull-ups and can be used as inputs. Port 0 is also the multiplexed low-order address and data bus during access to external program and data memory. In this application, it uses strong internal pull-ups when emitting 1s. Port 0 also outputs the code bytes during OTP programming veriﬁcation.

P1.0 to P1.2 25 to 27 I/O Port 1: Port 1 is an 8-bit quasi bidirectional I/O port with internal pull-ups.

Port 1 pins that have logic 1s written to them are pulled HIGH by the internal pull-ups and can be used as inputs. As inputs, port 1 pins that are externally pulled LOW will source current because of the internal pull-ups (see Chapter “DC characteristics”: I

). P1.0 to P1.2 have external interrupts INT2 to

INT4 assigned.

P1.3 28 I/O If the UART is disabled (ENS1 in S1CON.4 = 0) then P1.3 can be used as

general purpose P1 port pin. If the UART function is required, then a logic 1 must be written to P1.3. This I/O then becomes the RXD/data line of the UART.

1998 Oct 07 7

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

P1.4 29 I/O If the UART is disabled (ENS1 in S1CON.4 = 0) then P1.4 can be used as

general purpose P1 port pin. If the UART function is required, then a logic 1 must be written to P1.4. This I/O then becomes the TXD/clock line of the UART. P1.4 has external interrupt INT6 (X6) assigned.

30 S ground (connected to substrate)

31 S supply voltage for the core logic and most peripheral drivers of the PCA5007

(see V

DDA

)

ALE 32 I/O Address Latch Enable: output pulse for latching the low byte of the address

during an access to external memory.

PSEN 33 I/O Program Store Enable: the read strobe to external program memory. When

the device is executing code from the external program memory, PSEN is activated for each code byte fetch.

EA 34 I/O External Access Enable: EA must be externally held LOW to enable the

device to fetch code from external program memory locations 0000H to 4FFFH. If EA is held HIGH, the device executes from internal program memory unless the program counter contains an address greater the 4FFFH (20 kbytes).

TCLK 35 I clock input for use as timing reference in external access mode and emulation V

36 S Programming voltage (12.5 V) for the OTP. Is connected to VSS in the

application.

P1.6(SCL) 37 I/O If the I

C-bus is disabled (ENS1 in S1CON.6 = 0) then P1.6 can be used as general purpose P1 port pin. If the I2C-bus function is required, then a logic 1 must be written to P1.6. This I/O then becomes the clock line of the I2C-bus. P1.6 is equipped with an open-drain output buffer. The pin has no clamp diode to VDD.

P1.7(SDA) 38 I/O If the I

C-bus is disabled (ENS1 in S1CON.6 = 0) then P1.7 can be used as general purpose P1 port pin. If the I2C-bus function is required, then a logic 1 must be written to P1.7. This I/O then becomes the data line of the I2C-bus. P1.7 is equipped with an open-drain output buffer. The pin has no clamp diode to VDD.

XTL2 39 O output from the current source oscillator ampliﬁer XTL1 40 I input to the inverting oscillator ampliﬁer and time reference for pager decoder,

real-time clock and timers

BAT

41 S Supply terminal from battery . Is used for supplying parts of the chip that need to

operate at all times.

DD(DC)

42 O Supply voltage output of the DC/DC converter. An external capacitor is

required.

VIND 43 I Current input for the DC/DC converter. The booster inductor needs to be

connected externally.

SS(DC)

44 S ground (connected to substrate) OTP

RESETIN 45 I Schmitt trigger reset input for the PCA5007. External R and C need to be

connected to the battery supply. All internal storage elements (except microcontroller RAM) are initialized when this input is activated.

SYMBOL PIN TYPE DESCRIPTION

1998 Oct 07 8

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

RESOUT 46 O Monitor output for the emulation system. Is active (LOW) whenever a reset is

applied to the microcontroller. (a reset can be forced by RESETIN, watchdog or wake-up from DC/DC converter in off mode). A reset to the microcontroller initializes all SFRs and port pins; it has no impact on the blocks operating from V

BAT

P3.2 to P3.3 47 and 48 I/O Port 3: P3.2 and P3.3 are conﬁgured as push-pull output only (option 3R; see

Section 6.6). Using the software input commands or the secondary port function is possible by driving the port 3 output lines accordingly:

P3.2 secondary function: INT0 (external interrupt 0) P3.3 secondary function: INT1 (external interrupt 1)

SYMBOL PIN TYPE DESCRIPTION

Fig.2 Pin configuration.

handbook, full pagewidth

1 2 3 4 5 6 7 8

9 10 11

36 35 34 33 32 31 30 29 28 27 26

24 37

PCA5007H

MGR108

TCLK EA PSEN

P1.4 P1.3 P1.2 P1.1 P1.0

ALE

P3.2

RESOUT

RESETIN

SS(DC)

VIND

DD(DC)

XTL1

XTL2

P1.7

P1.6

P3.3

BAT

P3.4 P3.5

AT P2.0 P2.1 P2.2

P2.4 P2.5

P2.7 P0.0

P2.3

P2.6

P0.2

P0.3

P0.4

DDA

AFCOUT

I(D1)

Q(D0)

P0.5

P0.6

P0.7

P0.1

SSA

1998 Oct 07 9

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6 FUNCTIONAL DESCRIPTION

6.1 General

The PCA5007 contains a high-performance CMOS microcontroller and the required peripheral circuitry to implement high-speed pagers for the modern paging protocols. For this purpose, features such as FSK demodulator, protocol timer, real-time clock and DC/DC converter have been integrated on-chip.

The microcontroller embedded within the PCA5007 implements the standard 80C51 architecture and supports the complete instruction set of the 80C51 with all addressing modes.

The PCA5007 contains 20 kbytes of OTP program memory; 1-kbyte of static read/write data memory, 27 I/O lines, two 16-bit timer/event counters, a fifteen-source two priority-level, nested interrupt structure and on-chip oscillator and timing circuit.

The PCA5007 devices have several software selectable modes of reduced activity for power reduction; Idle for the CPU and standby or off for the DC/DC converter. The Idle mode freezes the CPU while allowing the RAM, timers, serial I/O and interrupt system to continue functioning. The standby mode for the DC/DC converter allows a high efficiency of the latter at low currents and the off mode reduces the supply voltage to the battery level. In the off mode the RAM contents are preserved, the real-time clock and protocol timer are operating, but all other chip functions are inoperative.

Two serial interfaces are provided on-chip; a UART serial interface and an I

C-bus serial interface. The I2C-bus serial interface has byte oriented master functions allowing communication with a whole family of I2C-bus compatible slave devices.

6.2 CPU timing

The internal CPU timing of the PCA5007 is completely different to other implementations of this core. The CPU is realized in asynchronous handshaking technology, which results in extremely low power consumption and low EMC noise generation.

6.2.1 B

ASICS

The implementation of the CPU of the PCA5007 as a block in handshake technology has become possible through the TANGRAM tool set, developed in the Philips Natlab in Eindhoven.

TANGRAM is a high level programming language which allows the description of parallel and sequential processes that can be compiled into logic on silicon. The CPU has the following features:

• No clock is needed. Every function within the CPU is self timed and always runs at the maximum speed that a given silicon die under the current operating conditions (supply voltage and temperature) allows.

• The CPU fetches opcodes with maximum speed until a special mode (e.g. Idle) is entered that stops this sequence.

• Only bytes that are required are fetched from the program memory. The dummy read cycles which exist in the standard 80C51 have been omitted to save power.

• To further speed up the execution of a program, the next sequential byte is always fetched from the code memory during the execution of the current command. In the event of jumps the prefetched byte is discarded.

• Since no clocks are required, the operating power consumption is essentially lower compared to conventional architectures and Idle power consumption is reduced to nearly zero (leakage only).

• Clocks are only required as timing references for timers/counters and for generating the timing to the off-chip world.

6.2.2 E

XECUTION OF PROGRAMS FROM INTERNAL CODE

MEMORY

When code is executed in internal access mode (EA = 1), the opcodes are fetched from the on-chip OTP. The OTP is a self timed block which delivers data at maximum speed. This is the preferred operating mode of the PCA5007.

6.2.3 E

XECUTION OF PROGRAMS FROM EXTERNAL CODE

MEMORY

When code is executed in external access mode (EA = 0), the opcodes are fetched from an off-chip memory using the standard signals ALE, PSEN and P0, P2 for multiplexed data and address information. In this mode the identical hardware configurations as for a standard 80C51 system can be used, even if the timing for ALE and PSEN is slightly different because it is generated from an internal oscillator.

1998 Oct 07 10

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.3 Overview on the different clocks used within the PCA5007

Figure 3 gives an overview on the clocks available within the PCA5007 for the different functions.

Fig.3 Overview on the clocks used within the PCA5007.

handbook, full pagewidth

MGR109

TIMER 1

(both clock edges

are used)

DEMODULATOR/

CLOCK RECOVERY

MICROCONTROLLER

OUTPUT AND

EXTERNAL ACCESS

TIMER 0

REAL-TIME CLOCK

WATCHDOG

WAKE-UP COUNTER

DC/DC CONVERTER

I2C-BUS

UART

(both clock edges

are used)

TONE GENERATOR

(both clock edges

are used)

76.8 kHz

256 Hz

4 Hz

16 Hz

9.6 kHz

6 MHz

76.8 kHz

400 kHz

6 MHz

DIVIDER

FOR THE

DIFFERENT

FREQUENCIES

÷150

÷9600

÷2400

÷4

DIVIDER

38.4 kHz

CORR

CLOCK

CORRECTION

76.8 kHz

OSCILLATOR

CCON.7

6 MHz

OSCILLATOR

OS6CON.7

1998 Oct 07 11

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.4 Memory organization

The PCA5007 has a program memory (OTP) plus data memory (RAM) on-chip. The device has separate address spaces for program and data memory (see Fig.4). If ports P0 and P2 are not used as I/O signals these pins can be used to address up to 64 kbytes of external program memory. In this case, the CPU generates the latch signal (ALE) for an external address latch and the read strobe (PSEN) for external program memory. External data memory is not supported.

6.4.1 P

ROGRAM MEMORY

After reset the CPU begins execution of the program memory at location 0000H. The program memory can be implemented in either internal OTP or external memory. If the EA pin is strapped to VDD, then program memory fetches are directed to the internal program memory. If the EA pin is strapped to VSS, then program memory fetches are directed to external memory.

Programming the on-chip OTP is detailed in Chapter 15. Usually Philips will deliver programmed parts to a customer. Supply of blank engineering samples is possible, but then Philips cannot give any guarantee on the programmability and retention of the program memory.

6.4.2 D

ATA MEMORY

The PCA5007 contains 1024 bytes of internal RAM (consisting of 256 bytes standard RAM and 768 bytes AUX-RAM) and Special Function Registers (SFRs). Figure 4 shows the internal data memory space divided into the lower 128 bytes the upper 128 bytes and the SFR space and 768 bytes auxiliary RAM. Internal RAM locations 0 to 127 are directly and indirectly addressable. Internal RAM locations 128 to 255 are only indirectly addressable. The SFR locations 128 to 255 are only directly addressable and the auxiliary RAM is indirectly addressable as external RAM (MOVX). External Data Memory (EDM) is not supported.

6.4.3 S

PECIAL FUNCTION REGISTERS

The second 128 bytes are the address locations of the special function registers. Table 1 shows the special function registers space. The SFRs include the port latches, timers, peripheral control, serial I/O registers, etc. These registers can only be accessed by direct addressing. There are 128 bit addressable locations in the SFR address space (those SFRs whose addresses are divisible by eight).

Fig.4 Memory map.

handbook, full pagewidth

MGR110

Internal RAM

INDIRECT AND

DIRECT

ADDRESSING

SFR space External XRAM

is not supported

EXTERNAL

(EAN = 0)

INTERNAL

(EAN = 1)

EXTERNAL

INDIRECT

ADDRESSING

DIRECT

ADDRESSING

Internal XRAM

INDIRECT

ADDRESSING

WITH DPTR

INDIRECT

ADDRESSING

WITH Ri, DPTR

FFH

00H

7FH

80H

2FFH

000H

0FFH

100H

DATA MEMORYPROGRAM MEMORY

4FFFH

FFFFH

1998 Oct 07 12

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.5 Addressing

The PCA5007 has five methods for addressing source operands:

• Register

• Direct

• Register-Indirect

• Immediate

• Base-Register plus Index-Register-Indirect.

The first three methods can be used for addressing destination operands. Most instructions have a ‘destination/source’ field that specifies the data type, addressing methods and operands involved. For operations other than MOVs, the destination operand is also a source operand.

Access to memory addressing is as follows:

• Registers in one of the four 8-register banks through Register-Direct or Register-Indirect

• Maximum 1024 bytes of internal data RAM through Direct or Register-Indirect

– Bytes 0 to 127 of internal RAM may be addressed

directly/indirectly. Bytes 128 to 255 of internal RAM share their address location with the SFRs and so may only be addressed Register-Indirect as data RAM.

– Bytes 0 to 768 of AUX-RAM can only be addressed

indirectly via MOVX. Bytes 256 to 768 can only be addressed using indirect addressing with the data pointer, while bytes 0 to 255 may be also addressed using R0 or R1.

• Special function registers through Direct

• Program memory Look-Up Tables (LUTs) through

Base-Register plus Index-Register-Indirect.

The PCA5007 is classified as an 8-bit device since the internal ROM, RAM, Special Function Registers (SFRs), Arithmetic Logic Unit (ALU) and external data bus are all 8 bits wide. It performs operations on bit, nibble, byte and double-byte data types.

Facilities are available for byte transfer, logic and integer arithmetic operations. Data transfer, logic and conditional branch operations can be performed directly on Boolean variables to provide excellent bit handling.

While the PCA5007 is executing code from the internal memory, ALE and

PSEN pins are inactive with

ALE = LOW and PSEN = HIGH. External XRAM is not supported for this device, since

P3.7 (RD) and P3.6 (WR) pins are not available. If the external XRAM is accessed accidentally, no PSEN or ALE cycle is done and actual P0 values are read. Internal XRAM access is not visible from outside the chip (no ALE, PSEN, P0 and P2 activity).

1998 Oct 07 13

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

Table 1 Special Function Registers Overview; note 1

ADDR

(HEX)

NAME 7 6 5 4 3 2 1 0 R/W

RESET VALUE

COMMENT

80 P0 R/W 9FH bit addressable 81 SP R/W 07H 82 DPL R/W 00H 83 DPH R/W 00H 87 PCON SMOD XRE ENIS − GF1 GF0 PD IDL R/W 00H 88 TCON TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 R/W 00H bit addressable 89 TMOD GATE C/T M1 M0 GATE C/T M1 M0 R/W 00H 8A TL0 R/W 00H 8B TL1 R/W 00H 8C TH0 R/W 00H 8D TH1 R/W 00H 90 P1 R/W FFH bit addressable 92 TGCON ENB CLK2 −−−− −−R/W 00H 93 TG0 R/W 00H 94 WUCON RUN WUP TEST CPL Z1 Z0 LOAD SET R/W 00H note 2 95 WUC0 R/W 00H note 2 96 WUC1 R/W 00H note 2 98 S0CON SM0 SM1 − REN TB8 RB8 TI RI R/W 00H bit addressable 99 S0BUF R/W 00H 9E AFCON ENB − AFC5 AFC4 AFC3 AFC2 AFC1 AFC0 R/W 00H A0 P2 R/W FFH bit addressable A5 WDCON COND WD3 WD2 WD1 WD0 −−LD R/W 00H A8 IEN0/IE EA EWU ES1 ES0 ET1 EX1 ET0 EX0 R/W 00H bit addressable B0 P3 R/W C3H bit addressable B8 IP/IP0 − PWU PS1 PS0 PT1 PX1 PT0 PX0 R/W 00H bit addressable C0 IRQ1 IQ9 IQ8 IQ7 IQ6 IQ5 IQ4 IQ3 IQ2 R/W 00H bit addressable

CD RTCON MIN −−−−W/

R LOAD SET R/W 00H note 2 CE RTC0 R/W 00H note 2 D0 PSW CY AC F0 RS1 RS0 OV P

(3)

R/W 00H bit addressable

D1 DCCON0 OFF SBY RXE SBLI −−STB

(3)

BLI

(3)

R/W 03H D2 DCCON1 VBG1 VBG0 VLO1 VLO0 −− −−R/W 00H D3 OS6CON ENB −

SF4 SF3 SF2 SF1 SF0 MFR R/W 00H D4 OS6M0 R 00H D8 S1CON − ENS1 STA STO SI AA −−R/W 00H bit addressable D9 S1STA SC4 SC3 SC2 SC1 SC0 0 0 0 R 78H DA S1DAT R/W 00H

E0 ACC R/W 00H bit addressable E8 IEN1 EMIN EWD EDC EX6 ESC EX4 EX3 EX2 R/W 00H bit addressable E9 IX1 IL9 IL8 IL7 IL6 IL5 IL4 IL3 IL2 R/W 00H

1998 Oct 07 14

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

Notes

1. An empty field in this map indicates a bit that can be read from or written to by software.

2. Value only reset with RESETIN and not or only partly with an off-restart sequence.

3. This bit cannot be changed by writing to it.

EC DMD0 ENB M − RES LEV BD2 BD1 BD0 R/W 00H ED DMD1 ENA AVG6 AVG5 AVG4 AVG3 AVG2 AVG1 AVG0 R 00H ENA is RW EE DMD2 ENC − BF − TEST B2 B1 B0 R/W 00H EF DMD3 R/W 00H

F0 B R/W 00H bit addressable

F8 IP1 PMIN PWD PDC PX6 PSC PX4 PX3 PX2 R/W 00H bit addressable FC CCON ENB PLUS TEST CIV17 CIV16 − BYPAS SET R/W 00H FD CC0 CIV7 CIV6 CIV5 CIV4 CIV3 CIV2 CIV1 CIV0 R/W 00H FE CC1 CIV15 CIV14 CIV13 CIV12 CIV11 CIV10 CIV9 CIV8 R/W 00H

ADDR

(HEX)

NAME 7 6 5 4 3 2 1 0 R/W

RESET VALUE

COMMENT

Fig.5 The lower 128 bytes of internal data memory.

handbook, halfpage

MLA560 - 1

07H

0FH

08H

17H

10H

1FH

18H

2FH

7FH

20H

30H

bit-addressable space (bit addresses 0 to 7F)

4 banks of 8 registers

(R0 to R7)

1998 Oct 07 15

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.6 I/O facilities

6.6.1 P

ORTS

The PCA5007 has 27 I/O lines treated as 27 individually addressable bits or as four parallel 8-bit addressable ports. Ports 0 and 2 are complete, Port 1 has only 7 and Port 3 has only 4 pins externally available. Ports 0, 1, 2 and 3 perform the following alternative functions:

Port 0 Is also used for external access, parallel OTP

programming mode and emulation (see Table 2 for configuration details):

• Provides the multiplexed low-order address and data bus for expanding the device with standard memories and peripherals

• Provides access to the OTP data I/O lines in OTP parallel programming mode.

Port 1 Used for a number of alternative functions

(see Table 3 for configuration details):

• Provides the inputs for the external interrupts INT2/P1.0 to INT4/P1.2 and INT6/P1.4

• SCL/P1.6 and SDA/P1.7 for the I2C-bus interface are real open-drain outputs; no other port configurations are available

• RXD/P1.3 and TXD/P1.4 for the UART data input and output.

Port 2 Is also used for external access, parallel OTP

programming mode and emulation (see Table 4 for configuration details):

• Provides the high-order address bus when expanding the device with external program memory

• Allows control of the on-chip OTP parallel programming mode.

Port 3 Pins are configured as strong push-pull outputs

(see Table 5 for configuration details). The following alternative Port 3 functions are available, but to avoid short-circuiting of the port pins, the input signals cannot be applied externally to the Port 3 pins. The alternative function can only be stimulated via the respective port output function:

• External interrupt request inputs INT0/P3.2 and INT1/P3.3

• Counter inputs T0/P3.4 and T1/P3.5.

To enable a port pin alternative function, the port bit latch in its SFR must contain a logic 1.

Each port consists of a latch (SFRs P0 to P3), an output driver and input buffer. Standard ports have internal pull-ups. Figure 6a shows that the strong transistor p1 is turned on for only a short time after a LOW-to-HIGH transition in the port latch. When on, it turns on p3 (a weak pull-up) through the inverter IN1. This inverter and p3 form a latch which holds the logic 1.

6.6.2 P

ORT I/O CONFIGURATION (OPTIONS)

I/O port output configurations are determined on-chip according to one of the options illustrated in Fig.6. They cannot be changed by software.

1998 Oct 07 16

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

Fig.6 Port configuration options.

a. Standard/quasi-bidirectional (option 1).

b. Push-pull (option 3).

c. Open-drain (only SDA/P1.7, SCL/P1.6; option 2).

handbook, full pagewidth

MGR111

I/O pin

strong pull-up

delay >50 ns

IN1

from port latch

weak pull-up

hold pull-up

input data

handbook, full pagewidth

MGR112

I/O pin

strong pull-up

from port latch

input data

handbook, full pagewidth

MGR113

LOW-PASS

FILTER

SLEW RATE

CONTROL

external

I/O pin

input data

external pull-up

from port latch

1998 Oct 07 17

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.6.3 PORT I/O CONFIGURATION Tables 2 to 6 show the hardwired configuration for the different I/Os of the PCA5007.

Table 2 Port 0 conﬁguration; notes 1 and 2

Notes

1. Option 1S means port configuration option 1 with post-reset set to HIGH; option 1R means post-reset state will be LOW.

2. ‘hys’ means input stage with hysteresis.

Table 3 Port 1 conﬁguration

Table 4 Port 2 conﬁguration

PORT PIN CONFIGURATION PULL-UP INPUT RESET DRIVE

POSSIBLE

APPLICATION IN A

PAGER

P0.0 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA LCD_enable (O) P0.1 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA SPI_enable (O) P0.2 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA SPI_clock (O) P0.3 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA SPI_data (O) P0.4 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA SPI_data (I) P0.5 quasi bidirectional I/O (option 1R) yes hys LOW 0.75 mA RXE (O) P0.6 quasi bidirectional I/O (option 1R) yes hys LOW 0.75 mA ROE (O) P0.7 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA bandwidth (O)/RSSI (I)

PORT PIN CONFIGURATION PULL-UP INPUT RESET DRIVE

POSSIBLE

APPLICATION IN A

PAGER

P1.0 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA Key P1.1 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA Key P1.2 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA Key P1.3 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA RXD P1.4 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA TXD P1.5 not available P1.6 I

C-bus open-drain I/O (option 2S)

(slew rate limited)

no hys HIGH 2.25 mA SCL

P1.7 I

C-bus open-drain I/O (option 2S)

(slew rate limited)

no hys HIGH 2.25 mA SDA

PORT PIN CONFIGURATION PULL-UP INPUT RESET DRIVE

POSSIBLE

APPLICATION IN A

PAGER

P2.0 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA LCD_Data P2.1 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA LCD_Data P2.2 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA LCD_Data P2.3 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA LCD_Data

1998 Oct 07 18

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

Table 5 Port 3 conﬁguration

The port configuration is fixed and cannot be reconfigured by software or ROM code.

Table 6 Other pins

P2.4 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA LCD_Data P2.5 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA LCD_Data P2.6 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA LCD_Data P2.7 quasi bidirectional I/O (option 1S) yes hys HIGH 0.75 mA LCD_Data

PORT PIN CONFIGURATION PULLUP INPUT RESET DRIVE

POSSIBLE

APPLICATION IN A

PAGER

P3.0 not available P3.1 not available P3.2 push-pull output (option 3R) no hys LOW 3 mA call LED P3.3 push-pull output (option 3R) no hys LOW 3 mA vibrator P3.4 push-pull output (option 3R) no hys LOW 3 mA backlight P3.5 push-pull output (option 3R) no hys LOW 3 mA LCD R/

W/RXD Enable P3.6 not available P3.7 not available

PORT PIN CONFIGURATION PULL-UP INPUT RESET DRIVE

POSSIBLE

APPLICATION IN A

PAGER

AT push-pull output no LOW 3 mA tone generator output I(D1) digital input no hys Q(D0) digital input no hys TCLK digital input no hys RESETIN digital input no hys reset input RESOUT push-pull output no LOW 1.5 mA reset output XTL1 analog input/output (10 pF) no hys to crystal quartz XTL2 analog input/output (10 pF) no to crystal quartz AFCOUT analog output no ALE quasi bidirectional I/O yes hys HIGH 1.5 mA PSEN quasi bidirectional I/O yes hys HIGH 0.75 mA EA 3-state I/O with bus keeper hold buffer HIGH 0.75 mA

PORT PIN CONFIGURATION PULL-UP INPUT RESET DRIVE

POSSIBLE

APPLICATION IN A

PAGER

1998 Oct 07 19

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.7 Timer/event counters

The PCA5007 contains two 16-bit timer/event counters, Timer 0 and Timer 1, which can perform the following functions:

• Measure time intervals and pulse durations

• Count events

• Generate interrupt requests

• Generate output on comparator match

• Generate a Pulse Width Modulated (PWM) output

signal.

Timer 0 and Timer 1 can be programmed independently to operate in four modes:

Mode 0: 8-bit timer or 8-bit counter each with divide-by-32 prescaler

Mode 1: 16-bit time interval or event counter Mode 2: 8-bit time interval or event counter with

automatic reload upon overflow Mode 3: this mode of the standard 80C51 is not

available.

In the timer mode the timers count events on the XTL1 input. Timer 0 counts through a prescaler at a rate of 256 Hz and Timer 1 counts directly on both edges of the XTL1 signal at a rate of 153.6 kHz. The nominal frequency of the XTL1 signal is 76.8 kHz.

In the counter mode, the register is incremented in response to a HIGH-to-LOW transition at P3.4 (T0) and P3.5 (T1).

Besides the different input frequencies and the non-availability of Mode 3, both Timer 0 and Timer 1 behave identically to the standard 80C51 Timer 0 and Timer 1.

Fig.7 Timer/counter 0 and 1: clock sources and control logic.

Detailed configuration of the 4 available modes is found in the 80C51 family hardware description (

“Philips Semiconductors IC20 Data Handbook”

handbook, full pagewidth

MGR114

153.6 kHz C/T = 0

C/T = 1

TL1 TH1

÷ 300

256 Hz

C/T = 0 C/T = 1

TL0

XTL1

TR0 Gate INT0

XTL1

TR1 Gate INT1

TH0

1998 Oct 07 20

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.8 I2C-bus serial I/O

The serial port supports the 2-line I2C-bus which consists of a data line (SDA) and a clock line (SCL). These lines also function as the I/O port lines P1.7 and P1.6 respectively. The system is unique because data transport, clock generation, address recognition and bus control arbitration are all controlled by hardware. The I2C-bus serial I/O has complete autonomy in byte handling. The implementation in the PCA5007 operates in single master mode as:

• Master transmitter

• Master receiver.

These functions are controlled by the S1CON register. S1STA is the status register whose contents may also be used as a vector to various service routines. S1DAT is the data shift register. The block diagram of the I2C-bus serial I/O is shown in Fig.8.

6.8.1 DIFFERENCES TO A STANDARD I2C-BUS INTERFACE The I2C-bus interface of the PCA5007 implements the

standard for master receiver and transmitter as defined in e.g. P83CL781/782 with the following restrictions:

• The baud rate is fixed to 100 kHz derived from the on-chip 6 MHz oscillator. Therefore bits CR0, CR1 and CR2 in the S1CON SFR are not available.

• Only single master functions are implemented. – Slave address (S1ADR) is not available – Status register (S1STA) reports only status defined

for the MST/TRX and MST/REC modes

– Multimaster operation is not supported.

Fig.8 Block diagram of I2C-bus serial I/O.

handbook, full pagewidth

MGL449

SHIFT REGISTER

S1DAT

SDA

ARBITRATION LOGIC

SCL BUS CLOCK GENERATOR

S1STA

INTERNAL BUS

76543210

S1CON

76543210

1998 Oct 07 21

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.8.2 SERIAL CONTROL REGISTER (S1CON)

Table 7 Serial Control Register (S1CON, SFR address D8H)

Table 8 Description of the S1CON bits

6.8.3 D

ATA SHIFT REGISTER (S1DAT)

S1DAT contains the serial data to be transmitted or data which has just been received. Bit 7 is transmitted or received first; i.e. data shifted from left to right.

Table 9 Data Shift Register (S1DAT, SFR address DAH)

6.8.4 A

DDRESS REGISTER (S1ADR)

The slave address register is not available since slave mode is not supported.

6.8.5 S

ERIAL STATUS REGISTER (S1STA)

The contents of this register may be used as a vector to a service routine. This optimizes the response time of the software and consequently that of the I2C-bus. S1STA is a read-only register. The status codes for all available modes of a single master I2C-bus interface are given in Tables 12 to 14.

76543210

−ENS1 STA STO SI AA −−

BIT SYMBOL FUNCTION

S1CON.7 − CR2 is not available. S1CON.6 ENS1 Enable Serial I/O. When ENS1 = 0, the serial I/O is disabled. SDA and SCL outputs are

in the high-impedance state; P1.6 and P1.7 function as open-drain ports. When ENS1 = 1, the serial I/O is enabled. Output port latches P1.6 and P1.7 must be set to logic 1.

S1CON.5 STA START ﬂag. If STA is set while the SIO is in master mode, SIO will generate a repeated

START condition.

S1CON.4 STO STOP ﬂag. With this bit set while in master mode a STOP condition is generated. When

a STOP condition is detected on the I

C-bus, the SIO hardware clears the STO ﬂag.

S1CON.3 SI SIO interrupt ﬂag. This ﬂag is set, and an interrupt is generated, after any of the

following events occur:

• A START condition is generated in master mode

• A data byte has been received or transmitted in master mode (even if arbitration is lost).

If this ﬂag is set, the I

C-bus is halted (by pulling down SCL). Received data is only valid

until this ﬂag is reset.

S1CON.2 AA Assert Acknowledge. When this bit is set, an acknowledge (LOW level to SDA) is

returned during the acknowledge clock pulse on the SCL line when:

• A data byte is received while the device is programmed to be a master receiver.

When this bit is reset, no acknowledge is returned. S1CON.1 − CR1 and CR0 are not available. S1CON.0 −

76543210

D7 D6 D5 D4 D3 D2 D1 D0

1998 Oct 07 22

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

Table 10 Serial Status Register (S1STA and SFR address D9H)

Table 11 Description of the S1STA bits

Table 12 MST/TRX mode

Table 13 MST/REC mode

Table 14 Miscellaneous

Table 15 Symbols used in Tables 12 to 14

76543210

SC4 SC3 SC2 SC1 SC0 0 0 0

BIT SYMBOL FUNCTION

S1STA.3 to S1STA.7 SC4 to SC0 5-bit status code S1STA.0 to S1STA.2 − these 3 bits are held LOW

S1STA VALUE DESCRIPTION

08H a START condition has been transmitted 10H a repeated START condition has been transmitted 18H SLA and W have been transmitted, ACK has been received 20H SLA and W have been transmitted,

ACK received 28H DATA of S1DAT has been transmitted, ACK received 30H DATA of S1DAT has been transmitted,

ACK received

S1STA VALUE DESCRIPTION

40H SLA and R have been transmitted, ACK received 48H SLA and R have been transmitted,

ACK received 50H DATA has been received, ACK returned 58H DATA has been received,

ACK returned

S1STA VALUE DESCRIPTION

78H no information available (reset value); the serial interrupt ﬂag SI, is not yet set

SYMBOL DESCRIPTION

SLA 7-bit slave address R read bit W write bit ACK acknowledgement (acknowledge bit = logic 0) ACK no acknowledgement (acknowledge bit = logic 1) DATA 8-bit data byte to or from I

C-bus MST master SLV slave TRX transmitter REC receiver

1998 Oct 07 23

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.9 Serial interface SIO0: UART

The UART interface of the PCA5007 implements a subset of the complete standard as defined in e.g. the P80CL580.

6.9.1 D

IFFERENCES TO THE STANDARD 80C51 UART

The following deviations from the standard exist:

• If [SM1 and SM0] = 10 then Mode 1 (8-bit data transmission) is selected, with a fixed baud rate (4800/9600 bits/s)

• If [SM1 and SM0] = 01 then Mode 2 (9-bit data transmission) is selected, with a fixed baud rate (4800/9600 bits/s)

• Modes 0 and 3 and the variable baud rate selection using Timer 1 overflow is not available

• The SM2 bit has no function

• The time reference for Modes 1 and 2 is taken from the

76.8 kHz oscillator, instead of the original

6.9.2 UART

MODES

This serial port is full duplex which means that it can transmit and receive simultaneously. It is also receive-buffered and can commence reception of a second byte before a previously received byte has been read from the register. However, if the first byte has not been read by the time the reception of the second byte is complete, the second byte will be lost. The serial port receive and transmit registers are both accessed via the special function register S0BUF. Writing to S0BUF loads the transmit register and reading from S0BUF accesses a physically separate receive register.

OSC

-----------

The serial port can operate in 2 modes: Mode 1 10 bits are transmitted (through TXD) or received

(through RXD): a START bit (0), 8 data bits (LSB first) and a STOP bit (1). On receive, the stop bit goes into RB8 in special function register S0CON (see Figs 9 and 10).

Mode 2 11 bits are transmitted (through TXD) or received

(through RXD): a START bit (0), 8 data bits (LSB first), a programmable 9th data bit and a STOP bit (1). On transmit, the 9th data bit (TB8 in S0CON) can be assigned the value of 0 or 1. Or, for example, the parity bit (P, in the PSW) could be moved into TB8. On receive, the 9th data bit goes into RB8 in S0CON, while the STOP bit is ignored (see Figs 9 and 11).

In both modes the baud rate can be selected to either 4800 or 9600 depending on the SMOD bit in the PCON SFR. If SMOD = 0 the baud rate is 4800, if SMOD = 1 the baud rate is 9600 with a 76.8 kHz quartz crystal.

In both modes, transmission is initiated by any instruction that uses S0BUF as a destination register. Reception is initiated by the incoming start bit if REN = 1.

6.9.3 S

ERIAL PORT CONTROL REGISTER (S0CON)

The serial port control and status register is the special function register S0CON (see Table 16). The register contains not only the mode selection bits, but also the 9th data bit for transmit and receive (TB8 and RB8), and the serial port interrupt bits (TI and RI).

Table 16 Serial Port Control Register (S0CON, SFR address 98H)

76543210

SM0 SM1 − REN TB8 RB8 TI RI

1998 Oct 07 24

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

Table 17 Description of the S0CON bits

Table 18 Selection of the serial port modes

6.9.4 UART

DATA REGISTER (S0BUF)

The UART data register (S0BUF) contains the serial data to be transmitted or data which has just been received. Bit 0 is transmitted or received first.

Table 19 Data Shift Register (S0BUF, SFR address 99H)

6.9.5 B

AUD RATES

The baud rate in Modes 1 and 2 depends on the value of the SMOD bit in SFR PCON and may be calculated as:

• If SMOD = 0, (which is the value on reset), the baud rate is

⁄16f

osc

• If SMOD = 1, the baud rate is1⁄8f

osc

BIT SYMBOL FUNCTION

S0CON.7 SM0 this bit together with the SM1 bit, is used to select the serial port mode; see Table 18 S0CON.6 SM1 this bit together with the SM0 bit, is used to select the serial port mode; see Table 18 S0CON.5 − SM2 is not available S0CON.4 REN this bit enables serial reception and is set by software to enable reception, and cleared by

software to disable reception

S0CON.3 TB8 this bit is the 9th data bit that will be transmitted in Mode 2; set or cleared by software as

desired S0CON.2 RB8 in Mode 2, this bit is the 9th data bit received; in Mode 1 it is the stop bit that was received S0CON.1 TI The transmit interrupt ﬂag; Set by hardware at the end of the 8th bit time in Mode 0, or at

the beginning of the stop bit time in the other modes, in any serial transmission; must be

cleared by software. S0CON.0 RI The receive interrupt ﬂag; Set by hardware at the end of the 8th bit time in Mode 0, or

halfway through the stop bit time in the other modes, in any serial transmission (for exception

see SM2); must be cleared by software.

SM0 SM1 MODE DESCRIPTION BAUD RATE

0 1 1 8-bit UART

⁄16f

osc

or1⁄8f

osc

1 0 2 9-bit UART

⁄16f

osc

or1⁄8f

osc

76543210

D7 D6 D5 D4 D3 D2 D1 D0

Baud rate

SMOD

---------------- -

osc

×=

1998 Oct 07 25

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

Fig.9 Serial port Mode 1and Mode 2.

handbook, full pagewidth

MGL452

START

STOP BIT SHIFT

DATA

TX CONTROL

TX CLOCK SEND

serial port

interrupt

RX CLOCK R1

LOAD SBUF

SHIFT

RX CONTROL

START

sample

INPUT SHIFT

(9-BITS)

BIT

DETECTOR

S0 BUFFER

INTERNAL BUS

READ SBUF

SHIFT

LOAD SBUF

S0 BUFFER

ZERO DETECTOR

SHIFT

D CL

TB8

INTERNAL BUS

write to

SBUF

XTL1

RXD

TXD

CSMOD at

PCON.7

HIGH-TO-LOW

TRANSITION

DETECTOR

1998 Oct 07 26

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in

_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in

white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...

Fig.10 Serial port Mode 1 timing.

handbook, full pagewidth

MGL451

D0 D1 D2 D3 D4 D5

D6 D7

START BIT

D4 D5

TX CLOCK

WRITE TO SBUF

DATA

SHIFT

TXD

START BIT

STOP BIT

÷8 RESET

RX CLOCK

RXD

STOP BIT

BIT DETECTOR SAMPLE TIME

SHIFT

SEND

T R A N S M

R E C E

I V E

1998 Oct 07 27

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in

_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in

white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...

Fig.11 Serial port Mode 2 timing.

handbook, full pagewidth

TX CLOCK

STOP BIT GEN

RX CLOCK

BIT DETECTOR SAMPLE TIME

SHIFT

MGL450

D0 D1 D2

D3 D4 D5 D6

D7 TB8

WRITE TO SBUF

SEND

DATA

SHIFT

TXD TI

START BIT

STOP BIT

÷8 RESET

START BIT

RXD

D0 D1 D2 D3 D4 D5 D6 D7

STOP BIT

RB8

T R A N S M

R E C E

V E

1998 Oct 07 28

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.10 76.8 kHz oscillator

6.10.1 F

UNCTION

The oscillator produces a reference frequency of 76.8 kHz. The frequency offset is compensated for by a separate digital clock correction block. The oscillator operates directly on V

BAT

and is always enabled.

6.10.2 O

SCILLATOR CIRCUITRY

The on-chip inverting oscillator amplifier is a single NMOS transistor supplied with a constant current. The amplitude visible at terminals XTL1 and XTL2 is therefore not a full rail swing with a very high impedance. To reduce the power consumption, the input Schmitt trigger buffer is limited to approximately 100 kHz maximum frequency.

The whole circuit operates directly at the battery supply. The 76.8 kHz oscillator cannot be disabled. It also continues its operation during DC/DC converter off or 8051 stop mode.

The simplest application configuration is shown in Fig.12a. C1 and C2 can be added to operate a crystal at its optimum load condition. The resulting capacitance of the series connection of C1 and C2 must be smaller than 5 pF for a guaranteed start-up of the oscillator.

Fig.12 Oscillator circuit.

handbook, full pagewidth

MGR115

2 MΩ

76.8 kHz

10 pF

(a) (b) (c)

10 pF

76.8 kHz 76.8 kHz 76.8 kHz

XTL1 XTL2

76.8 kHz

10 pF10 pF

XTL1 XTL2

2 MΩ

VP = V

BAT

max

= 100 kHz

10 pF10 pF

XTL1 XTL2

1998 Oct 07 29

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.11 Clock correction

6.11.1 F

UNCTION

The clock correction block is connected to the 76.8 kHz oscillator. It operates directly from V

BAT

. By means of the clock correction circuit a digital adjustment of the 76.8 kHz oscillator signal is implemented.

An 18-bit interval counter inserts or deletes one pulse from the 76.8 kHz clock each time its count has expired. The interval is stored by the processor to the 18-bit interval register CIV. Addition or deletion is performed by hardware.

Crystal offset correction can be performed with a resolution of 5 ppm.

This block also generates the timing reference signals for other functional blocks such as the RTC (4 Hz), watchdog (16 Hz), Timer 0 (256 Hz), wake-up counter (9600 Hz) and the demodulator/clock recovery block. The generation of these timing references is always active and cannot be disabled.

Fig.13 Block diagram for clock compensation.

handbook, full pagewidth

MGR116

QD Q

STORE

76.8 kHz

corrected

38.4 kHz

internal set flag

SFR to

microcontroller

RESET

with each

OFF cycle

SET ENB PLUS

BYPASS TEST

CIV0 to CIV17

INTERVAL LATCH

(18-BIT)

reload data

INTERVAL COUNTER

(18-BIT)

(RELOAD ON CARRY)

VDD supply

RESET only

on RESETIN

CARRY

ADD/DELETE

ONE PULSE

ON CARRY

÷2

BAT

supply

1998 Oct 07 30

Philips Semiconductors Product speciﬁcation

Pager baseband controller PCA5007

6.11.2 CLOCK CORRECTION CONTROL REGISTER (CCON) The CCON special function register is used to control the clock correction by software.

Table 20 Clock Correction Control Register (CCON, SFR address FCH)

Table 21 Description of the CCON bits

6.11.3 C

LOCK CORRECTION INTERVAL REGISTERS (CC0 AND CC1)

The CC0 and CC1 special function registers (together with CCON.3 and CCON.4) are used to define the interval between subsequent clock correction actions.

Table 22 Clock Correction Interval Register (CC0, SFR address FDH)

Table 23 Clock Correction Interval Register (CC1, SFR address FEH)

76543210

ENB PLUS TEST CIV17 CIV16 −

BYPASS

SET

BIT SYMBOL FUNCTION

CCON.7 ENB Enable clock correction. If ENB = 1 has been set, then correction is enabled and will

stay enabled even when the DC/DC converter is shut down and restarted. CCON.6 PLUS ± sign for value. If PLUS = 1 then clock pulses are inserted, or else deleted. CCON.5 TEST Test signal, must always be logic 0 in normal mode. It is s used during test to bypass

the ﬁrst 9 FFs in the timing generator divider chain. If TEST = 1 the clock rate of the

signals 9600 Hz and 256 Hz is doubled and the frequency on 16 Hz and 4 Hz is

multiplied by 300. CCON.4 CIV17 bit 17 of interval value, is used as extension of CC0 and CC1 CCON.3 CIV16 bit 16 of interval value, is used as extension of CC0 and CC1 CCON.2 − unused. CCON.1 BYPASS Test signal, must always be logic 0 in normal mode. It is used during test to generate

76.8 kHz on all outputs of the timing generator (4 Hz, 16 Hz, 256 Hz and 9600 Hz).

CCON.0 SET A load signal to the interval register. After a logic 0 to logic 1 transition of this bit the

value of ENB, PLUS, TEST, BYPASS and CIV are copied into the local latches with the

next 76.8 kHz clock pulse. The duration of one MOV instruction is long enough for the

set operation to complete. The SFR values must remain stable for at least one oscillator

period because the actual transfer happens synchronized with the local clock

(see Figs 14 and 16).

76543210

CIV7 CIV6 CIV5 CIV4 CIV3 CIV2 CIV1 CIV0

76543210

CIV15 CIV14 CIV13 CIV12 CIV11 CIV10 CIV9 CIV8

+ 82 hidden pages