Philips p8xcx66 DATASHEETS

INTEGRATED CIRCUITS

DATA SH EET

P8xCx66 family

Microcontrollers for PAL/SECAM TV with OSD and VST

Product speciﬁcation File under Integrated Circuits, IC20

1999 Mar 10

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

1 FEATURES 2 GENERAL DESCRIPTION 3 ORDERING INFORMATION 4 BLOCK DIAGRAM 5 PINNING INFORMATION 6 MEMORY ORGANIZATION 7 I/O FACILITY 8 TIMERS AND EVENT COUNTERS 9 REDUCED POWER MODE 10 I2C-BUS SERIAL I/O 11 INTERRUPT SYSTEM 12 OSCILLATOR CIRCUITRY 13 RESET CIRCUITRY 14 PIN FUNCTION SELECTION 15 ANALOG CONTROL 16 ANALOG-TO-DIGITAL CONVERTERS (ADC) 17 ON-SCREEN DISPLAY (OSD) 18 EPROM PROGRAMMER 19 SPECIAL FUNCTION REGISTERS

ADDRESS MAP 20 LIMITING VALUES 21 CHARACTERISTICS 22 PINNING CHARACTERIZATION 23 PACKAGE OUTLINES 24 SOLDERING 25 DEFINITIONS 26 LIFE SUPPORT APPLICATIONS 27 PURCHASE OF PHILIPS I2C COMPONENTS

P8xCx66 family

1999 Mar 10 2

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

1 FEATURES

1.1 P80C51 CPU core

• 80C51 8-bit CPU

• 64-kbyte Multiple Programming ROM (MTP ROM)

• Two 16-bit timer/event counters

• Crystal oscillator for system clock (up to 12 MHz)

• 12 source, 12 vector interrupt structure with two priority

levels

• Enhanced architecture with:

– Non-page orientated instructions – Direct addressing – Four 8-byte RAM register banks – Stack depth up to 128 bytes – Multiply, divide, subtract and compare instructions.

1.2 P8xCx66 family

• ROM/RAM: see Table 1

• Pulse Width Modulated (PWM) outputs:

– One 14-bit PWM output for Voltage Synthesized

Tuning (VST)

– Eight 7-bit PWM outputs for analog controls.

• 3 Analog-to-Digital (ADC) inputs with 4-bit DAC and

comparator

• LED driver port:

– All I/O port lines with 10 mA LED drive capability

<1.0 V)

– Up to 5 LEDs can be driven at any one time.

• Serial I/O:

– Multi-master I2C-bus interface – Maximum I2C-bus frequency 400 kHz.

• Watchdog timer

• Improved EMC measures and slope controlled I/Os

• OSD functions:

– Programmable VSYNC and HSYNC active levels – Display RAM: 192 × 12 bits – Display character fonts: 128 (126 customer fonts plus

2 reserved codes)

– 63 vertical starting positions controlled by software

P8xCx66 family

– 110 horizontal starting positions controlled by

software

– Character size: 4 different character sizes on a

line-by-line basis

– Character matrix: 12 × 18 with no spacing between

characters

– Foreground colours: 8 on a character-by-character

basis

– Background/shadowing modes: two primary modes -

TV mode and Frame mode on a frame basis. Each primary mode has four sub-modes on a line basis: Sub-mode 1: Superimpose (no background) Sub-mode 2: North-West shadowing Sub-mode 3: Box background Sub-mode 4: Border shadowing

– Background colours: 8 on a word-by-word basis,

available in all four sub-modes

– Display RAM starting address is programmable; fast

switching between banks of display (RAM)

characters is possible through software control – HSYNC driven PLL for OSD clock (4 to 12 MHz) – Character blinking ratio: 1 : 1 – Character blinking frequency: programmable using

divisors of 32 and 64, on a character basis

VSYNC

– Flexible display format using the Carriage Return

code and the Space codes – Display RAM address post incremented each time

new data is written into RAM – Vertical jitter cancelling circuit to avoid unstable

VSYNC leading edge mismatch with HSYNC signal – OSD meshing.

• Power-on reset

• Packages: SDIL42 (PLCC68 for piggy-back only)

• Operating voltage: 4.5 to 5.5 V

• Operating temperature: −20 to +70 °C

• System clock frequency: 4 to 12 MHz

• OSD clock frequency: 4 to 12 MHz.

1999 Mar 10 3

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV

P8xCx66 family

with OSD and VST

2 GENERAL DESCRIPTION

The P8xCx66 family consists of the following devices:

• P83C266

• P83C366

• P83C566

• P83C766

• P87C766.

The P8xCx66 family are 80C51-based microcontrollers designed for medium-high to high-end TV control applications. The P8xCx66 devices incorporate many unique features on-chip, giving them a competitive edge over similar devices from other manufacturers.

Table 1 Memory structure for the different family members

MEMORY P83C266 P83C366 P83C566 P83C766 P87C766

ROM 24 kbytes 32 kbytes 48 kbytes 64 kbytes − RAM 512 bytes 512 bytes 1 kbyte 1 kbyte 2 kbytes EPROM −−−−64 kbytes Main memory 256 bytes 256 bytes 256 bytes 256 bytes 256 bytes Auxiliary RAM 256 bytes 256 bytes 768 bytes 768 bytes 1792 bytes

The Philips 80C51 CPU is object code compatible with the industry standard 80C51. All devices are manufactured in an advanced CMOS technology.

The P8xCx66 family also function as arithmetic processors having facilities for both binary and BCD arithmetic plus bit handling capabilities. The instruction set consists of over 100 instructions: 49 one-byte, 46 two-byte and 16 three-byte. Multiply and divide instructions are implemented by hardware with a cycle time of 4 µs

= 12 MHz).

CLK

The term P8xCx66 is used throughout this data sheet to refer to all family members; differences between devices are highlighted in the text.

3 ORDERING INFORMATION

TYPE NUMBER

NAME DESCRIPTION VERSION

P83C266BDR SDIP42 plastic shrink dual in-line package; 42 leads (600 mil) SOT270-1 P83C366BDR P83C366CBP P83C566BDR P83C766BDP P87C766BDR P87C766CBP P83C366BDA PLCC68 plastic leaded chip carrier; 68 leads SOT188-2 P83C566BDA P83C766BDA P87C766CBA

PACKAGE

1999 Mar 10 4

This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in

_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in

white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...

1999 Mar 10 5

(3)

DDD

SSD

(3)

ok, full pagewidth

RB GFB HSYNC

VSYNC

4 BLOCK DIAGRAM

Microcontrollers for PAL/SECAM TV

with OSD and VST

Philips Semiconductors Product speciﬁcation

ROM

32 KBYTES

EPROM

64 KBYTES

XTALIN

XTALOUT

RESET

CPU

80C51 CORE

EXCLUDING

ROM/RAM

internal

interrupts

external

interrupts

TWO 16-BIT

TIMER/ COUNTERS (T0 AND T1)

PARALLEL

I/O PORT

8 4

8-BIT

WATCHDOG

TIMER

(T3)

FUNCTION

COMBINED

PARALLEL I/O PORTS

(1) For the P83C366. (2) For the P87C766. (3) Alternative functions of Port 1. (4) Alternative functions of Port 5, except PWM7 which is an alternative function of Port 3. (5) Alternative functions of Port 3.

(1)

512 BYTES

8 × 7-BIT

DACS

2 KBYTES

(2)

PWM0 to PWM7

RAM

(4)

(1)

(2)

8-bit internal bus

ON SCREEN DISPLAY

(OSD)

PLL

14-BIT DAC

(4)

TPWM

ADC0

3 × 4-BIT

ADCS

ADC1

(5)

ADC2

P8xCx66

INTERFACE

(5)

SDA

I2C-BUS

(3)

SCL

DDA

SSA

MGL302

(3)

P8xCx66 family

Fig.1 P83C366 and P87C766 block diagram.

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

5 PINNING INFORMATION

5.1 Pinning

handbook, halfpage

P5.0/TPWM P5.1/PWM0 P5.2/PWM1 P5.3/PWM2 P5.4/PWM3 P5.5/PWM4 P5.6/PWM5 P5.7/PWM6

P3.0/ADC0 P3.1/ADC1 P3.2/ADC2

P3.3/PWM7

P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7

SSD

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20

P8xCx66

MGL301

42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 2221

DDD

P1.7 P1.6/SDA P1.5/SCL P1.4/T1 P1.3/INT0 P1.2/T0 P1.1/INT1 P1.0 RESET XTALOUT XTALIN

SSA

DDA

VSYNC HSYNC FB R G B

P8xCx66 family

Fig.2 Pin configuration (SDIP42).

1999 Mar 10 6

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

n.c.

P5.5/PWM4

P5.4/PWM3

P5.3/PWM2

P5.2/PWM1

P5.1/PWM0

handbook, full pagewidth

P5.6/PWM5 P5.7/PWM6

P3.0/ADC0

PH1SEM

S1ESEM

P3.1/ADC1

P2.0

P3.2/ADC2

P2.1

P3.3/PWM7

P2.2 P2.3 P0.0 P0.1 P0.2

OSD_EPR_TST

n.c.

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

P5.0/TPWM

INTD

P87C766

VSSV 1

DDD1VSSD1

P1.7 66

P1.6/SDA

P1.5/SCL

P1.4/T1 63

P8xCx66 family

P1.3/INT0

n.c.

P1.2/T0

P1.1/INT1

P1.0

EMUPBX

RESET

IDLPDEM

P2.7

XTALOUT

XTALIN

P2.6

SSA

DDA

n.c.

P0.3

P0.4

P0.5

P0.6

P0.7

DDD

Fig.3 Pin configuration (PLCC68).

1999 Mar 10 7

P2.4

P2.5

HSYNC

MGL329

n.c.

VSYNC

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV

P8xCx66 family

with OSD and VST

5.2 Pin description Table 2 Pin description for SDIP42 and PLCC68 packages

SYMBOL

P5.0/TPWM 1 3 I/O Port 5: 8-bit open-drain, bidirectional port.(P5.0 to P5.7) with 8 alternative P5.1/PWM0 2 4 P5.2/PWM1 3 5 P5.3/PWM2 4 6 P5.4/PWM3 5 7 P5.5/PWM4 6 8 P5.6/PWM5 7 11 P5.7/PWM6 8 12 P3.0/ADC0 9 13 I/O Port 3: 4-bit open-drain, bidirectional port.(P3.0 to P3.3) with 4 alternative P3.1/ADC1 10 16 P3.2/ADC2 11 18 P3.3/PWM7 12 20 P0.0 to P0.7 13 to 20 23 to 25,

SSD

B 22 37 O OSD blue colour output. G 23 38 O OSD green colour output. R 24 39 O OSD red colour output. FB 25 40 O OSD fast blanking output. HSYNC 26 41 I TV horizontal sync Schmitt trigger input (for OSD synchronization). VSYNC 27 42 I TV vertical sync Schmitt trigger input (for OSD synchronization). V

DDA

SSA

XTALIN 31 50 I Crystal input. XTALOUT 32 51 O Crystal output.

SDIP42 PLCC68

I/O DESCRIPTION

functions.

TWPM: 14-bit PWM output. PWM0 to PWM6: 7-bit PWM outputs.

functions.

ADC0 to ADC2: ADC inputs. PWM7: 7-bit PWM output.

I/O Port 0: 8-bit open-drain, bidirectional port (P0.0 to P0.7).

28 to 32

21 − Ground line for digital circuits.

28 45 − 5 V analog power supply. 29 46 − Ground line for analog circuits. 30 48 I +12.75 V programming voltage supply (OTP) for EPROM only. 0 V in

normal application. For the ROM version this pin is not connected.

1999 Mar 10 8

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV

P8xCx66 family

with OSD and VST

SYMBOL

RESET 33 54 I Reset input. P1.0 34 57 I/O Port 1: 8-bit open-drain, bidirectional port (P1.0 to P1.7) with 6 alternative P1.1/INT1 35 58 P1.2/T0 36 59 P1.3/INT0 37 62 P1.4/T1 38 63 P1.5/SCL 39 64 P1.6/SDA 40 65 P1.7 41 66 V

DDD

n.c. − 9, 10, 27,

INTD − 2 I These 3 signals are used for metalink+ emulation. PH1SEM − 14 I/O S1ESEM − 15 I/O P2.0 − 17 I/O Port 2: 8-bit open-drain, bidirectional port (P2.0 to P2.7). P2.1 − 19 P2.2 − 21 P2.3 − 22 P2.4 − 35 P2.5 − 36 P2.6 − 47 P2.7 − 52 OSD_EPR_

TST IDLPDEM − 53 I/O These 2 signals are used for metalink+ emulation. EMUPBX − 55 I/O V

SSD1

DDD1

SDIP42 PLCC68

42 33 − 5 V digital power supply.

− 1, 49, 56 − Ground lines.

43, 44,

60, 61

− 26 I/O OSD EPROM test enable.

− 67 − Ground line for digital circuits.

− 68 − 5 V digital power supply.

I/O DESCRIPTION

functions.

INT1 and INT0: external interrupts 1 and 0. T1 and T0: 16-bit timer/counter 1 and 0 inputs

SCL: I SDA: I2C-bus data line

− not connected

C-bus clock line

1999 Mar 10 9

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

6 MEMORY ORGANIZATION

The P8xCx66 family provides 24, 32, 48 or 64 kbytes of program memory (ROM/EPROM) plus 512, 1024 or 2048 bytes of data memory (RAM) on-chip (see Table 1). The device has separate address spaces for program and data memory (see Fig.4). These devices have no external memory access capability as the RD (read), WR (write), EA (External Access), PSEN (read strobe) and ALE (Address Latch Enable) signals are not bonded out.

6.1 Data memory

The P8xCx66 family contains 512, 1024 or 2048 bytes of internal RAM and 56 Special Function Registers (SFRs). Figure 4 shows the internal data memory space divided into the lower 128, the upper 128, AUX-RAM and the SFR space. The lower 128 bytes of internal RAM are organized as shown in Fig.5. The lowest 32 bytes are grouped into 4 banks of 8 registers. Program instructions refer to these registers as R0 to R7. Two bits in the Program Status Word (PSW) select which register bank is in use. The next 16 bytes above the register bank form a block of bit-addressable memory space. The 128 bits in this area can be directly addressed by the single-bit manipulation instructions. The remaining registers (30H to 7FH) are directly and indirectly byte addressable. The registers that reside at addresses above 7FH and up to FFH can only be accessed indirectly. These register addresses overlap the SFR addresses as described in Section 6.2.

6.2 Special Function Registers

The upper 128 bytes are the address locations of the SFRs when accessed directly. SFRs include the port latches, timers, 7-bit PWMs, 14-bit VST PWM, ADCs and OSD control registers. These registers can only be accessed by direct addressing. There are 128 bit-addressable locations in the SFR address space (SFRs with addresses divisible by eight). Their addresses are a multiple of 08H, from 80H to F8H. (i.e., 80H, 88H, 90H, 98H etc.). See Chapter 19 for SFR list.

P8xCx66 family

6.3 AUX RAM

The 1792 byte (P87C766) or 768 byte (P83C766) AUX RAM, while physically located on-chip, logically occupies the first 1792/768 bytes of external data memory. As such, it is indirectly addressed in the same way as external data memory using MOVX instructions in combination with any of the registers R0, R1 or DPTR.

6.4 Addressing

The P80C51 CPU has five methods for addressing source operands

• Register

• Direct

• Register-indirect

• Immediate

• Base-register-plus index-register-indirect.

The first three methods can be used for addressing destination operands. Most instructions have a ‘destination/source’ field that specifies the data type, addressing methods and operands involved. For operations other than MOVs, the destination operand is also a source operand.

Access to memory addressing is as follows:

• Registers in one of the four register banks through register direct or indirect

• Internal RAM (128 bytes) through direct or register-indirect

• Special Function Registers through direct

• External data memory through register-indirect

(for AUX RAM)

• Program memory look-up tables through base-register-plus index-register-indirect.

1999 Mar 10 10

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

handbook, full pagewidth

64 KBYTES

INTERNAL

PROGRAM MEMORY

(1) For the P83C766 and the P87C766. (2) For the P87C766. (3) For the P83C566 and the P83C766.

(1)

AUX RAM

1792 BYTES

768 BYTES

Fig.4 Memory map.

P8xCx66 family

OVERLAPPED SPACE

(2)

(3)

255

127

INTERNAL

DATA RAM

INTERNAL DATA MEMORY

SPECIAL

FUNCTION

REGISTERS

MGM680

handbook, halfpage

R0 R7

7FH

30H 2FH

20H 1FH

18H 17H

10H 0FH

08H 07H

(bit addresses 00H to 7FH)

4 banks of 8 registers

MGM677

Fig.5 The lower 128 bytes of internal RAM.

bit-addressable space

(R0 to R7)

1999 Mar 10 11

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

7 I/O FACILITY

7.1 I/O ports

The SDIP42 package has 28 I/O lines treated as 28 individual addressable bits or as 3 parallel 8-bit addressable ports (Ports 0, 1 and 5) and one 4-bit port (Port 3).

When these 28 I/O lines are used as input ports, the corresponding bits in SFRs P0, P1, P3 and P5 should be set to a logic 1 to facilitate the external input signal.

Ports 1, 3 and 5 also perform the following alternative functions.

Port 1. Used for a number of special functions:

• Provides the external interrupt inputs (INT0 and INT1)

• Provides the 16-bit timer/counter inputs (T0 and T1)

• Provides the I

SCL)

• P1.0 and P1.7 can be used as external interrupt inputs.

C-bus data and clock signals (SDA and

P8xCx66 family

Port 3. Only 4 lines available for alternative functions:

• 7-bit PWM output (PWM7)

• ADC inputs ADC0 to ADC2.

Port 5.

• Provides the 14-bit PWM output (TPWM)

• 7-bit PWMs outputs (PWM0 to PWM6).

To enable the alternative functions of Ports 1, 3 and 5, the port bit latch of its associated SFR must contain a logic 1.

Each port consists of a latch (SFRs P0, P1, P3 and P5), an output driver and an input buffer.

7.2 Port conﬁgurations

1. Open-drain quasi-bidirectional I/O with n-channel

pull-down (see Fig.6). Use as an output requires the connection of an external pull-up resistor. Use as an input requires to write a logic 1 to the port latch before reading the port line.

2. Push-pull; gives drive capability of the output in both

polarities, see Fig.7.

handbook, halfpage

from port latch

input data

read port pin

INPUT

BUFFER

Fig.6 Open-drain port.

I/O pin

MGK547

handbook, halfpage

from port latch

strong pull-up

+5 V

output pin

MGM679

Fig.7 Push-pull port.

1999 Mar 10 12

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

8 TIMERS AND EVENT COUNTERS

The P8xCx66 contains two 16-bit timers/counters: Timer 0 and Timer 1 and also an 8-bit Watchdog timer.

8.1 16-bit timer/counters (T0 and T1)

Timer 0 and Timer 1 perform the following functions:

• Measure time intervals and pulse durations

• Count events

• Generate interrupt requests.

Timer 0 and Timer 1 can be independently programmed to operate in one of four modes.

Mode 0 8-bit timer or counter with divide-by-32 prescaler. Mode 1 16-bit time-interval or event counter. Mode 2 8-bit time-interval or event counter with automatic

reload upon overflow.

Mode 3 Timer 0 establishes TL0 and TL1 as two

separate counters.

In the ‘timer’ function, the register is incremented every machine cycle. Since a machine cycle consists of 12 oscillator periods, the count rate is

In the ‘counter’ function, the register is incremented in response to a HIGH-to-LOW transition. Since it takes 2 machine cycles (24 oscillator periods) to recognize a HIGH-to-LOW transition, the maximum count rate is

⁄24f

. To ensure that a given level is sampled, it should

osc

be held for at least one complete machine cycle.

8.2 Watchdog timer (T3)

In addition to the standard timers, a Watchdog timer is implemented on-chip. The Watchdog timer generates a hardware reset upon overflow. In this way a microcontroller system can recover from erroneous processor states caused by electrical noise, RFI or unexpected ROM code behaviour.

⁄12f

osc

P8xCx66 family

The Watchdog timer consists of an 8-bit timer with an 11-bit prescaler as shown in Fig.8. The prescaler input

frequency is ‘t’ seconds where ‘t’ is calculated as shown below:

t 12 2048×

The 8-bit timer is an up-counter so a value 00H gives the maximum timer interval (510 ms at 12 MHz, 1536 ms at 4 MHz), and a value of FFH gives the minimum timer interval (2 ms at 12 MHz, 6 ms at 4 MHz). When the 8-bit timer produces an overflow a short internal reset pulse is generated which will reset the P8xCx66.

The timer has no disable function. Consequently, all applications must reload the timer within the previously loaded timer interval otherwise a reset will occur. The timer is not stopped in the Idle mode. The interrupt routine for the Idle mode should also service the Watchdog timer.

The Watchdog timer is controlled by the WLE bit in the Power Control Register (see Section 9.6). The WLE bit must be set by the Watchdog timer service routine before the timer interval can be loaded into T3. A load of T3 automatically clears the WLE bit.

A system reset clears the Watchdog timer and the prescaler.

8.2.1 W

Table 3 Watchdog timer Register (SFR address FFH)

76543210

T37 T36 T35 T34 T33 T32 T31 T30

⁄12f

. The 8-bit timer is incremented every

osc

×=

-------f

osc

ATCHDOG TIMER REGISTER (WDT)

1999 Mar 10 13

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

ndbook, full pagewidth

1/12 f

write T3

osc

PRESCALER

11-BIT

INTERNAL BUS

WDT REGISTER

(8-BIT)

LOADCLEAR LOADEN

CLEAR

WLE IDL

PCON.4

RESET

P8xCx66 family

internal reset

RESET

LOADEN

PCON.0

INTERNAL BUS

Fig.8 Block diagram of the Watchdog timer.

MGL298

1999 Mar 10 14

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

9 REDUCED POWER MODE

Only one reduced power mode is implemented; this is the Idle mode.

During Idle mode all blocks are inactive except Timer 0, Timer 1, INT0, INT1 and the Watchdog timer. These active functions may generate an interrupt (if their interrupts are enabled) and this will cause the device to leave the Idle mode.

The Idle mode is activated by software using the PCON register; this register is described in Section 9.6.

9.1 Idle mode

The instruction that sets PCON.0 is the last instruction executed before entering the Idle mode. Once in the Idle mode, the internal clock is gated away from the CPU and from all derivative functions (PWM/TPWM/ADC/I except Timer 0, Timer 1 and interrupts INT0 and INT1. The Watchdog timer remains active. The CPU status is preserved along with the Stack Pointer, Program Counter, Program Status Word and the Accumulator. The RAM and all other registers maintain their data during Idle mode and the port pins retain the logic states held at Idle mode activation. The OSD clock is gated away from OSD circuit in Idle mode.

9.2 Recover from Idle mode

There are 3 methods used to terminate the Idle mode.

9.2.1 V Activation of INT0, INT1 or an interrupt from Timer 0 or

Timer 1 will cause PCON to be cleared by hardware thus terminating the Idle mode. The interrupt is serviced and following the RETI instruction, the next instruction to be executed will be the one following the instruction that put the device in the Idle mode. All the other interrupts are disabled and will not generate an interrupt to wake-up the CPU.

9.2.2 V The second method of terminating the Idle mode is with an

external hardware reset. Since the oscillator is still running, the hardware reset is required to be active for only two machine cycles to complete the reset operation. Reset redefines all SFRs, but does not effect the on-chip RAM.

IA AN INTERRUPT

IA RESET

C-bus),

P8xCx66 family

9.2.3 V

If the Watchdog timer is allowed to overflow or an erroneous processor state causes an overflow, a hardware reset will be generated, thus terminating the Idle mode.

9.3 General purpose ﬂags (GF0 and GF1)

Flags GF0 and GF1 may be used to determine whether the interrupt was received during normal execution or Idle mode. For example, the instruction that writes to PCON.0 to set the Idle mode can also set or clear one or both flags. When the Idle mode is terminated by an interrupt, the service routine can examine the status of the flag bits.

9.4 Output in Idle mode

• Ports will keep the value they had before entering the Idle mode

• The PWM0 to PWM7 outputs will be LOW

• The TPWM output will be LOW

• The I

• The pins R, G, B and FB will be the ‘inverse of Bp’,

(defined by bit 2 of SFR OSCON).

9.5 Pending interrupts in Idle mode

If pending interrupts (I P1.7) are present at the moment the CPU is switched to Idle mode, then these interrupts will wake-up the CPU. If this is not wanted then before entering the Idle mode all interrupts must be disabled, except those interrupts allowed to wake-up the CPU (INT0, INT1, Timer 0 and Timer1). New interrupts from I2C-bus, VSYNC, P1.0 to P1.4 or P1.7 are disabled as soon as Idle mode is entered.

For example if a high priority interrupt is serviced just before the instruction which sets PCON.0 and a lower priority interrupt is generated during the interrupt service routine of the high priority interrupt, then the lower priority interrupt is pending. After the high priority interrupt is serviced (last instruction of routine is RETI) the main program will execute at least one more instruction to prevent a deadlock of the main program. In this case, it is the instruction which sets the PCON.0 bit (enter Idle mode). The pending lower level interrupt will, if enabled, immediately wake-up the CPU for an interrupt service, even though this interrupt is not INT0, INT1 or an interrupt from Timer 1 or Timer 0.

IA A WATCHDOG TIMER OVERFLOW

C-bus output is HIGH

C-bus, VSYNC, P1.0 to P1.4 or

1999 Mar 10 15

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV

P8xCx66 family

with OSD and VST

9.6 Power Control Register (PCON)

PCON is byte addressable only.

Table 4 Power Control Register (SFR address 87H)

76543210

−−−WLE GF1 GF0 0 IDL

Table 5 Description of PCON bits

BIT SYMBOL DESCRIPTION

7 − These 3 bits are reserved. 6 − 5 − 4 WLE Watchdog Load Enable. If WLE = 1, the Watchdog timer can be loaded. If WLE = 0,

the Watchdog timer cannot be loaded. 3 GF1 General purpose flag 1. 2 GF0 General purpose flag 0. 1 − This bit is reserved and must be set to a logic 0. 0 IDL Idle mode select. If IDL = 1, the Idle mode is selected. If IDL = 0, the Idle mode is

inhibited, i.e. normal operation.

1999 Mar 10 16

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

10 I2C-BUS SERIAL I/O

10.1 The I

The serial port supports the two line I2C-bus. The I2C-bus consists of a serial data line (SDA) and a serial clock line (SCL). These lines can also function as I/O port lines P1.6 and P1.5 respectively. To utilize this facility pins P1.5/SCL and P1.6/SDA must be configured as alternative functions instead of port lines; see Section 10.8.

The system is unique because data transport, clock generation, address recognition and bus control arbitration are all controlled by hardware.

Full details of the I2C-bus are given in the document

“The I2C-bus and how to use it”

ordered using the code 9398 393 40011.

C-bus

. This document may be

P8xCx66 family

10.2 Operation modes

The I

C-bus serial I/O has complete autonomy in byte

handling and operates in four modes

• Master transmitter

• Master receiver

• Slave transmitter

• Slave receiver.

These functions are controlled by the S1CON register. S1STA is the status register whose contents may also be used as a vector to various service routines. S1DAT is the data shift register and S1ADR the slave address register. Slave address recognition is performed by hardware.

handbook, full pagewidth

SLAVE ADDRESS

S1ADR

SDA

ARBITRATION LOGIC

SCL BUS CLOCK GENERATOR

76543210

S1CON

76543210

S1STA

SHIFT REGISTER

S1DAT

MBC749 - 1

Fig.9 Block diagram of I2C-bus serial I/O.

INTERNAL BUS

1999 Mar 10 17

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV

P8xCx66 family

with OSD and VST

10.3 Serial Control Register (S1CON) Table 6 Serial Control Register (SFR address D8H)

76543210

CR2 ENS1 STA STO SI AA CR1 CR0

Table 7 Description of S1CON bits

BIT SYMBOL DESCRIPTION

6 ENSI Enable Serial I/O. When ENSI = 0, the SIO is disabled and reset. The SDA and SCL

outputs are in a high-impedance state; P1.5 and P1.6 function as open-drain ports.

When ENSI = 1, the SIO is enabled. The P1.5 and P1.6 port latches must be set to

logic 1. 5 STA START ﬂag. When the STA bit is set in Slave mode, the SIO hardware checks the

status of the I

while the SIO is in Master mode, SIO transmits a repeated START condition. 4STOSTOP ﬂag. With this bit set while in Master mode a STOP condition is generated. When

a STOP condition is detected on the bus, the SIO hardware clears the STO ﬂag. In the

Slave mode, the STO ﬂag may also be set to recover from an error condition. In this

case, no STOP condition is transmitted to the I

hardware behaves as if a STOP condition has been received and releases SDA and

SCL. The SIO then switches to the ‘not addressed’ slave receiver mode. The STO ﬂag

is automatically cleared by hardware. 3SISIO interrupt ﬂag. When the SI ﬂag is set, an acknowledge is returned after any one of

the following conditions:

• A START condition is generated in Master mode

• Own slave address received during AA = 1

• General call address received while S1ADR.0 = 1 and AA = 1

• Data byte received or transmitted in Master mode (even if arbitration is lost)

• Data byte received or transmitted as selected slave

• STOP or START condition received as selected slave receiver or transmitter.

2AAAssert Acknowledge. When the AA ﬂag is set, an acknowledge (LOW level to SDA)

will be returned during the acknowledge clock pulse on the SCL line when:

• Own slave address is received

• General call address is received (S1ADR.0 = 1)

• Data byte received while device is programmed as a Master receiver

• Data byte received while device is a selected Slave receiver.

With AA = 0, no acknowledge will be returned. Consequently, no interrupt is requested

when the ‘own slave address’ or general call address is received. 7 CR2 Clock Rate selection. These three bits determine the serial clock frequency when SIO 1 CR1 0 CR0

is in a Master mode; see Table 8. The maximum I

C-bus and generates a START condition if the bus is free. If STA is set

C-bus interface. However, the SIO

C-bus frequency is 400 KHz.

1999 Mar 10 18

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV

P8xCx66 family

with OSD and VST

Table 8 Selection of SCL frequency in Master mode

CR2 CR1 CR0 f

0 0 0 60 200 0 0 1 1600 7.5 0 1 0 40 300 0 1 1 30 400 1 0 0 240 50 1 0 1 3200 3.75 1 1 0 160 75 1 1 1 120 100

10.4 Status Register (S1STA)

S1STA is an 8-bit read-only Special Function Register. The contents of S1STA may be used as a vector to a service routine. This optimizes response time of the software and consequently that of the I possible modes of the I2C-bus interface are given in Table 12. The abbreviations used in Table 12 are defined in Table 11.

DIVISOR BIT RATE (kHz) at f

osc

C-bus. The status codes for all

= 12 MHz

osc

Table 9 Status Register (SFR address D9H)

76543210

SC4 SC3 SC2 SC1 SC0 0 0 0

Table 10 Description of S1STA bits

BIT SYMBOL DESCRIPTION

7 to 3 SC4 to SC0 5-bit status code; see Table 12. 2to0 − These 3 bits are held LOW.

Table 11 Abbreviations used in Table 12

SYMBOL DESCRIPTION

SLA 7-bit slave address

R read bit

W write bit ACK acknowledgment (Acknowledge bit = 0) ACK not acknowledge (Acknowledge bit = 1)

DATA 8-bit byte to or from the I

MST master

SLV slave

TRX transmitter

REC receiver

C-bus

1999 Mar 10 19

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

Table 12 Status codes

S1STA VALUE DESCRIPTION

MST/TRX mode

08H a START condition has been transmitted 10H a repeated START condition has been transmitted 18H SLA and W have been transmitted, ACK received 20H SLA and W have been transmitted. 28H DATA of S1DAT has been transmitted, ACK received 30H DATA of S1DAT has been transmitted, 38H arbitration lost in SLA, R/W or DATA

MST/REC mode

38H arbitration lost while returning 40H SLA and R have been transmitted, ACK received 48H SLA and R have been transmitted, 50H DATA has been received, ACK returned 58H DATA has been received,

P8xCx66 family

ACK received

ACK

ACK received

ACK returned

SLV/REC mode

60H own SLA and W have been received, ACK returned 68H arbitration lost in SLA, R/W as MST; own SLA and W have been received,

70H general CALL has been received, ACK returned 78H arbitration lost in SLA, R/W as MST; general CALL has been received 80H previously addressed with own SLA; DATA byte received, ACK returned 88H previously addressed with own SLA; DATA byte received, 90H previously addressed with general CALL; DATA byte has been received, ACK returned 98H previously addressed with general CALL; DATA byte has been received,

A0H a STOP condition or repeated START condition has been received while still addressed

SLV/TRX mode

A8H own SLA and R have been received. ACK returned B0H arbitration lost in SLA, R/W as MST. Own SLA and R have been received, ACK

B8H DATA byte has been transmitted, ACK received C0H DATA byte has been transmitted, C8H last DATA byte has been transmitted (AA = logic 0) ACK received

Miscellaneous

00H bus error during MST mode or SLV mode, due to an erroneous START or STOP

ACK

returned

ACK returned

as SLV/REC or SLV/TRX

returned

ACK received

condition

1999 Mar 10 20

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV

P8xCx66 family

with OSD and VST

10.5 Data Shift Register (S1DAT)

S1DAT contains the serial data to be transmitted or data that has just been received. Bit 7 is transmitted or received first.

Table 13 Data Shift Register (SFR address DAH)

76543210

D7 D6 D5 D4 D3 D2 D1 D0

10.6 Slave Address Register (S1ADR)

This 8-bit register may be loaded with the 7-bit slave address to which the controller will respond when programmed as slave receiver/transmitter. The LSB bit (GC) is used to determine whether the general CALL address is recognized.

Table 14 Slave Address Register (SFR address DBH)

76543210

SLA6 SLA5 SLA4 SLA3 SLA2 SLA1 SLA0 GC

Table 15 Description of S1ADR bits

BIT SYMBOL DESCRIPTION

7 to 1 SLA6 to

SLA0

0 GC When GC = 0, the general CALL address is not recognized. When GC = 1, the general

Own slave address.

CALL address is recognized.

10.7 Internal Status Register (S1IST)

S1IST is an 8-bit read-only Special Function Register and will exist in the design but is not mapped for the user.

Table 16 Internal Status Register (SFR address DCH)

76543210

MST TRX BB FB ARL SEL AD0 SHRA

10.8 I Table 17 I

Table 18 Description of I

C-bus Control Register (I2CCON)

C-bus Control Register (SFR address 86H)

76543210

−−−−−I

CCON bits

BIT SYMBOL DESCRIPTION

7to3 − These 5 bits are not used.

1to0 − These bits are not used.

CE I2C-bus enable. This bit selects the functions of pins 39 and 40 for the SDIP42 package

(or pins 64 and 65 for the PLCC68 package). When I2CE = 1, the alternative functions SCL and SDA are selected. When I2CE = 0, these pins act as port lines P1.5 and P1.6.

CE −−

1999 Mar 10 21

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

11 INTERRUPT SYSTEM

External events and the real-time driven on-chip peripherals require service by the CPU asynchronous to the execution of any particular section of code. To tie the asynchronous activities of these functions to normal program execution a multiple-source, two-priority-level, nested interrupt system is provided. The P8xCx66 acknowledges interrupt requests from twelve sources as shown in Table 20.

Each interrupt vectors to a separate location in program memory for its service routine. Each source can be individually enabled or disabled by using corresponding bits in the Interrupt Enable Registers (IEN0 and IEN1). The priority level is selected via the Interrupt Priority Registers (IP0 and IP1). All enabled sources can be globally disabled or enabled. The minimum width of the external interrupt signal is ≥6 XTAL clocks. The maximum width of the interrupt signal is the total length of all instructions in the interrupt service routine until the clear instruction of the IRQ bit. The external interrupts are INT0, INT1, P1.0, P1.1, P1.2, P1.3, P1.4 and P1.7.

11.1 External interrupts INT2 to INT7 and INT9

Port 1 lines also serve as additional interrupts INT2 to INT7 (P1.0, P1.1, P1.2, P1.3, P1.4 and P1.7). INT7 is used by the derivative functional blocks as follows:

X7 VSYNC interrupt 0063H

P8xCx66 family

Register. Each flag will be set on interrupt request but it must be cleared by software, i.e. via the interrupt software.

11.2 Interrupt priority

Each interrupt source can be set to either high or low priority. If both priorities are requested simultaneously, the controller will branch to the high priority vector.

A low priority interrupt can only be interrupted by a high priority interrupt. A high priority interrupt routine cannot be interrupted

11.3 Related registers

The following registers are used in conjunction with the interrupt system.

Table 19 Interrupt registers

Interrupt Polarity Register (IX1) E9H Interrupt Request Flag Register (IRQ1) C0H Interrupt Enable Register 0 (IEN0) A8H Interrupt Enable Register 1 (IEN1);

interrupts INT2 to INT9 Interrupt Priority Register 0 (IP0) B8H Interrupt Priority Register 1 (IP1);

interrupts INT2 to INT9

E8H

F8H

Using the IX1 register, each pin may be initialized to be either active HIGH or active LOW except INT7 which is fixed active HIGH because this interrupt is from another derivative function. IRQ1 is the Interrupt Request Flag

Table 20 Interrupt request (priority within level)

INTERRUPT MNEMONIC SOURCE VECTOR ADDRESS

PX0 (highest) external interrupt 0 (INT0) 0003H S1 I2C-bus 002BH T0 Timer 0 overflow 000BH PX2 P1.0 port line 0033H PX6 P1.4 port line 005BH PX1 external interrupt 1 (INT1) 0013H PX3 P1.1 port line 003BH PX7 VSYNC interrupt 0063H T1 Timer 1 overflow 001BH PX4 P1.2 port line 0043H PX5 P1.3 port line 004BH PX9 (lowest) P1.7 port line 0073H

1999 Mar 10 22

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

handbook, full pagewidth

INTERRUPT

SOURCES

PX0

PX2

IEN0/1

REGISTERS

IP0/1

REGISTERS

P8xCx66 family

PRIORITY

HIGH

LOW

PX6

PX1

PX3

PX7

PX4

PX5

PX9

GLOBAL ENABLE

INTERRUPT POLLING SEQUENCE

MGL297

Fig.10 Interrupt system.

1999 Mar 10 23

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV with OSD and VST

handbook, full pagewidth

P1.7

VSYNC

P1.4

P1.3

P1.2

P1.1

P1.0

IX1

IEN1

P8xCx66 family

IRQ1

MGL296

Fig.11 External and derivative interrupt configuration.

1999 Mar 10 24

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV

P8xCx66 family

with OSD and VST

11.4 Interrupt Enable Register 0 (IEN0) Table 21 Interrupt Enable Register (SFR address A8H)

76543210

EA − ES1 − ET1 EX1 ET0 EX0

Table 22 Description of IEN0 bits A logic 0 disables the interrupt; a logic 1 enables the interrupt.

BIT SYMBOL DESCRIPTION

7EAGeneral enable/disable control. When EA = 0, no interrupt is enabled. When EA = 1,

any individually enabled interrupt will be accepted.

6 − not used

5 ES1 enable I 4 − not used 3 ET1 enable Timer 1 interrupt 2 EX1 enable external interrupt 1 1 ET0 enable Timer 0 interrupt 0 EX0 enable external interrupt 0

C-bus SIO interrupt

11.5 Interrupt Enable Register 1 (IEN1) Table 23 Interrupt Enable Register (SFR address E8H)

76543210

EX9 − EX7 EX6 EX5 EX4 EX3 EX2

Table 24 Description of IEN1 bits Where EXx = 0, interrupt disabled. EXx = 1, interrupt enabled

BIT SYMBOL DESCRIPTION

7 EX9 enable external interrupt 9 (P1.7 port line) 6 − not used 5 EX7 enable external interrupt 7 (VSYNC interrupt) 4 EX6 enable external interrupt 6 (P1.4 port line) 3 EX5 enable external interrupt 5 (P1.3 port line) 2 EX4 enable external interrupt 4 (P1.2 port line) 1 EX3 enable external interrupt 3 (P1.1 port line) 0 EX2 enable external interrupt 2 (P1.0 port line)

1999 Mar 10 25

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV

P8xCx66 family

with OSD and VST

11.6 Interrupt Priority Register 0 (IP0) Table 25 Interrupt Priority Register 0 (SFR address B8H)

76543210

−−PS1 − PT1 PX1 PT0 PX0

Table 26 Description of IP0 bits A logic 0 selects low priority; a logic 1 selects high priority.

BIT SYMBOL DESCRIPTION

7 − These 2 bits are not used. 6 −

5 PS1 I 4 − This bit is not used. 3 PT1 Timer 1 interrupt priority level 2 PX1 external interrupt 1 priority level 1 PT0 Timer 0 interrupt priority level 0 PX0 external interrupt 0 priority level

C-bus SIO interrupt priority level

11.7 Interrupt Priority Register 1 (IP1) Table 27 Interrupt Priority Register 1 (SFR address F8H)

76543210

PX9 − PX7 PX6 PX5 PX4 PX3 PX2

Table 28 Description of IP1 bits Where PXx = 0 selects low priority; PXx = 1 selects high priority.

BIT SYMBOL DESCRIPTION

7 PX9 enable external interrupt 9 priority level (P1.7 port line) 6 − not used 5 PX7 enable external interrupt 7 priority level (VSYNC interrupt) 4 PX6 enable external interrupt 6 priority level (P1.4 port line) 3 PX5 enable external interrupt 5 priority level (P1.3 port line) 2 PX4 enable external interrupt 4 priority level (P1.2 port line) 1 PX3 enable external interrupt 3 priority level (P1.1 port line) 0 PX2 enable external interrupt 2 priority level (P1.0 port line)

1999 Mar 10 26

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV

P8xCx66 family

with OSD and VST

11.8 Interrupt Polarity Register (IX1)

Writing a logic 1 to bits IL9, IL6, IL5, IL4, IL3 and IL2 will set the polarity level of the corresponding external interrupt to be active HIGH. Writing a logic 0 to these bits will set the corresponding external interrupt to be active LOW.

External interrupts INT1 and INT0 however can be programmed to be edge sensitive. Writing a logic 1 to bits IL8 and IL7 will activate the external interrupts INT1 and INT0 on a rising edge (LOW-to-HIGH). Writing a logic 0 to bits IL8 and IL7 will activate the external interrupts INT1 and INT0 on a falling edge (HIGH-to-LOW). This feature is useful for pulse width measurement; see Section 11.8.1.

Table 29 Interrupt Polarity Register (SFR address E9H)

76543210

IL9 IL8 IL7 IL6 IL5 IL4 IL3 IL2

Table 30 Description of IX1 bits

BIT SYMBOL DESCRIPTION

7 IL9 external interrupt 9 polarity level (P1.7 port line) 6 IL8 external interrupt 1 polarity level (INT1) polarity level 5 IL7 external interrupt 0 polarity level (INT0) polarity level 4 IL6 external interrupt 6 polarity level (P1.4 port line) 3 IL5 external interrupt 5 polarity level (P1.3 port line) 2 IL4 external interrupt 4 polarity level (P1.2 port line) 1 IL3 external interrupt 3 polarity level (P1.1 port line) 0 IL2 external interrupt 2 polarity level (P1.0 port line)

11.8.1 P

ULSE WIDTH MEASUREMENT EXAMPLE

To determine the LOW time of a signal on the external interrupt pin INT0 the following sequence should be followed.

1. External interrupt 0 must be programmed to edge sensitivity (SFR TCON, address 88H).

2. IL7 must be programmed as shown in Fig.12.

3. The value held in Timer 0 or Timer 1 represents the pulse width of the signal on the INT0 pin.

handbook, full pagewidth

INT0

IL7

INT0(CPU)

Start interrupt service routine to start counting system clock periods with Timer 0 or Timer 1

Start interrupt service routine to stop counting of Timer 0 or Timer 1

MGL295

Fig.12 Pulse width measurement timing diagram.

1999 Mar 10 27

Philips Semiconductors Product speciﬁcation

Microcontrollers for PAL/SECAM TV

P8xCx66 family

with OSD and VST

11.9 Interrupt Request Flag Register (IRQ1)

Bits IQ9 and IQ6 to IQ2 will be set to a logic 1, if one of the two conditions specified below is met:

• If its associated port line is programmed to generate an interrupt when HIGH (selected using the Interrupt Polarity Register) and the state of that port line is HIGH

• If its associated port line is programmed to generate an interrupt when LOW (selected using the Interrupt Polarity Register) and the state of that port line is LOW.

IQ7 is set to a logic 1, if the interrupt condition is met within the corresponding derivative function. Therefore, all IRQ1 bits serve not only as pending interrupt request bits but also as interrupt status bits. This means that even if the external interrupts are disabled (using the Interrupt Enable Register 1) the IRQ1 bits can still be set to a logic 1 if the interrupt condition is met within the corresponding derivative function. For example, if the interrupt condition within VSYNC is met then:

• If IEN0.7 = X, IEN1.5 = 0 then IRQ1.5 = 1, no pending interrupt to CPU

• If IEN0.7 = 0, IEN1.5 = 1 then IRQ1.5 = 1, interrupt to CPU is pending

• If IEN0.7 = 1, IEN1.5 = 1 then IRQ1.5 = 1, interrupt will be serviced when either:

– The CPU finishes current instruction, if not in the interrupt service routine – The current interrupt service routine is interrupted if the VSYNC has a higher interrupt priority – This VSYNC interrupt becomes pending, waiting until the current higher priority level interrupt is serviced.

Bits IQ9 and IQ7 to IQ2 can be reset by software.

Table 31 Interrupt Request Flag Register (SFR address C0H)

76543210

IQ9 − IQ7 IQ6 IQ5 IQ4 IQ3 IQ2

Table 32 Description of IRQ1 bits

BIT SYMBOL DESCRIPTION

7 IQ9 external interrupt 9 request flag (P1.7 port line) 6 − reserved 5 IQ7 external interrupt 7 request flag (VSYNC interrupt) 4 IQ6 external interrupt 6 request flag (P1.4 port line) 3 IQ5 external interrupt 5 request flag (P1.3 port line) 2 IQ4 external interrupt 4 request flag (P1.2 port line) 1 IQ3 external interrupt 3 request flag (P1.1 port line) 0 IQ2 external interrupt 2 request flag (P1.0 port line)

1999 Mar 10 28

+ 64 hidden pages

Philips p8xcx66 DATASHEETS

CONTENTS

1 FEATURES

1.1 P80C51 CPU core

1.2 P8xCx66 family

2 GENERAL DESCRIPTION

3 ORDERING INFORMATION

4 BLOCK DIAGRAM

5 PINNING INFORMATION

5.1 Pinning

5.2 Pin description Table 2 Pin description for SDIP42 and PLCC68 packages

6 MEMORY ORGANIZATION

6.1 Data memory

6.2 Special Function Registers

6.3 AUX RAM

6.4 Addressing

7 I/O FACILITY

7.1 I/O ports

8 TIMERS AND EVENT COUNTERS

8.1 16-bit timer/counters (T0 and T1)

8.2 Watchdog timer (T3)

9 REDUCED POWER MODE

9.1 Idle mode

9.2 Recover from Idle mode

9.4 Output in Idle mode

9.5 Pending interrupts in Idle mode

9.6 Power Control Register (PCON)

10 I2C-BUS SERIAL I/O

10.2 Operation modes

10.3 Serial Control Register (S1CON) Table 6 Serial Control Register (SFR address D8H)

10.4 Status Register (S1STA)

10.5 Data Shift Register (S1DAT)

10.6 Slave Address Register (S1ADR)

10.7 Internal Status Register (S1IST)

11 INTERRUPT SYSTEM

11.1 External interrupts INT2 to INT7 and INT9

11.2 Interrupt priority

11.3 Related registers

11.4 Interrupt Enable Register 0 (IEN0) Table 21 Interrupt Enable Register (SFR address A8H)

11.5 Interrupt Enable Register 1 (IEN1) Table 23 Interrupt Enable Register (SFR address E8H)

11.6 Interrupt Priority Register 0 (IP0) Table 25 Interrupt Priority Register 0 (SFR address B8H)

11.7 Interrupt Priority Register 1 (IP1) Table 27 Interrupt Priority Register 1 (SFR address F8H)

11.8 Interrupt Polarity Register (IX1)

11.9 Interrupt Request Flag Register (IRQ1)