Philips MP2, MP5 Installation Manual

Installation Guide

Philips MP2/MP5 Roll Stand

The purpose of this guide is to:

1. Describe assembly of Roll Stand (pages 2 – 3).

2. Describe attachment of Fixed Tilt Mounts (page 4).

3. Describe mounting MP5 on Roll Stand (page 5).

4. Describe mounting MP2 on Roll Stand (page 6).

5. Describe cable management – MP2 only (page 7).

Parts Reference

The following parts and hardware are included with this installation kit (hardware not shown):

Tools Required: Phillips screwdriver (not provided), 1/2'' [13mm] wrench (not provided).

WARNING: USE OF THIS ROLL STAND FOR INSTRUMENTS OTHER THAN THOSE DESCRIBED IN

THIS DOCUMENT MAY RESULT IN INJURY DUE TO TIPPING OF THE ROLL STAND. THE CUSTOMER
SHOULD VERIFY THE STABILITY OF ANY DEVIATION FROM THE CONFIGURATIONS SHOWN.

Item # Description Qty

1 Post, 40'' 1

2 Base, 21'' 1

3 5/16-18 x 1'' Hex Head Cap Screw (HHCS) 1

4 5/16 Flat Washer 1

5 5/16 Split Lock Washer 1

6 Utility Basket 1

7 Basket Clip 2

8 #8-32 x 7/8'' Pan Head Machine Screw (PHMS) 2

9 #8-32 Hex Nut 2

10 Handle 1

11 #10-32 x 9/16'' PHMS 4

12 Fixed Tilt Mount, MP5

13 Fixed Tilt Mount, MP2 1

14 M4 x 14mm PHMS 2

15 #10-32 x 3/4'' Flat Head Machine Screw (FHMS) 3

16 Power Supply Mount 1

17 M4 x 12mm PHMS 2

18 M6 x 10mm FHMS 3

19 M6 x 8mm PHMS 2

20 Cable Clip (not shown – see page 7) 2

21 Screw Cover, Adhesive-backed Lexan 1

1

12

10

6

2

13

16

DU-PH-0062-60 Rev A 7/16/07 GCX Corp Page 1 of 7

Assembling the Roll Stand

1. Insert bottom end of Post in center of Base and lay assembly on its side for access to bottom of base (not shown).

2. Using a 1/2'' [13mm] wrench, fasten Post to Base with one (1) 5/16-18 x 1'' HHCS, with 5/16 split lock washer, and
5/16'' flat washer as shown below. Return Roll Stand to upright position.

5/16 Flat Washer

5/16 Lock Washer

5/16-18 x 1'' HHCS

DU-PH-0062-60 Rev A 7/16/07 GCX Corp Page 2 of 7

Attaching Utility Basket and Handle to Roll Stand Post

1. Attach two (2) Basket Clips to Utility Basket as shown below left. Insert two (2) #8-32 x 7/8'' PHMS and #8-32 hex nuts
in Basket Clips but do not tighten.

2. Slide Basket Clips over top end of Roll Stand Post (below right) and move Basket to mounting position. Do not tighten
screws at this time. Basket may require re-alignment after the Fixed Tilt Mount is attached.

Basket Clips

#8-32 x 7/8'' PHMS (2)
#8-32 Hex Nuts (2)

3. Position the Handle below the top of the Roll Stand Post opposite the Basket. Fasten Handle to Post with two (2) #10­32 x 9/16'' PHMS as shown, but do not tighten at this time. Handle may require re-alignment after the Fixed Tilt Mount
is attached.

#10-32 x 9/16'' PHMS (2)

DU-PH-0062-60 Rev A 7/16/07 GCX Corp Page 3 of 7